NCP3231 D

NCP3231
High Current Synchronous
Buck Converter
The NCP3231 is a high current, high efficiency, voltage−feed−
forward voltage−mode synchronous buck converter which operates
from 4.5 V to 18 V input and generates output voltages down to 0.6 V
at up to 25 A DC load or 30 A instantaneous load.
www.onsemi.com
Features
MARKING
DIAGRAM
Wide Input Voltage Range from 4.5 V to 18 V
0.6 V Internal Reference Voltage
500 kHz Switching Frequency
External Programmable Soft−start
Lossless Low−side FET Current Sensing
Output Over−voltage Protection and Under−voltage Protection
System Over−temperature Protection using a Thermistor or Sensor
Hiccup Mode Operation for All Faults
Pre−bias Start−up
Adjustable Output Voltage
Power Good Output
Internal Over−temperature Protection
This is a Pb−Free Device*
1
1 40
NCP3231
A
WL
YY
WW
G
ISET
SS
AGND
FB
OTS
COMP
PG
VIN
VIN
VIN
4
1
5
3
6
2
8
9
7
10
VIN
11
VIN
12
VIN
13
VIN
14
37 PGND
VSWH
15
36 BST
PGND
16
PGND
17
PGND
18
PGND
19
32 VSWH
PGND
20
31 VSWH
40 EN
VIN
EP42
39 VCC
GND
EP41
38 VB
35 VSW
34 VSWH
27
28
29
PGND
PGND
VSWH
30
26
PGND
VSWH
25
PGND
23
PGND
24
22
33 VSWH
PGND
21
VSWH
EP43
PGND
Cellular Base Stations
ASIC, FPGA, DSP and CPU Core and I/O Supplies
Telecom and Network Equipment
Server and Storage System
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
PIN CONNECTIONS
Typical Applications
•
•
•
•
NCP3231
AWLYYWWG
QFN40 6x6, 0.5P
CASE 485CM
PGND
•
•
•
•
•
•
•
•
•
•
•
•
•
(TOP VIEW)
ORDERING INFORMATION
Device
Package
Shipping†
NCP3231MNTXG
QFN−40
(Pb−Free)
2500 /
Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2015
May, 2015 − Rev. 5
1
Publication Order Number:
NCP3231/D
NCP3231
VB
VCC
LDO
VCC
VB
VB
VB
BST
VIN
OSC
COMP
VDD
VREF
FB
Control Logic
Ramp Generator
PWM Logic
+
E/A
−
− and −
VSWH
SS
UVLO
OVP, UVP
Power Good
OCP, TSD
Protection
Soft Start
VCC
2 mA
EN
VB
VSW
PVDD
Enable
Logic
1.2 V
POR
PGND
PG
VB
+
−
VREF
OTS
ISET
AGND
Figure 1. NCP3231 Block Diagram
www.onsemi.com
2
NCP3231
PIN DESCRIPTION
Pin No.
Symbol
1
SS
A capacitor from this pin to GND allows the user to adjust the soft−start ramp time.
Description
2
FB
Output voltage feedback.
3
COMP
4
ISET
5
AGND
6
OTS
7
PG
Power good indicator of the output voltage. Open−drain output. Connect PG to VDD with an external resistor.
8−14,
EP42
VIN
The VIN pin is connected to the internal power NMOS switch. The VIN pin has high di/dt edges and must be
decoupled to ground close to the pin of the device.
15, 29−34,
EP43
VSWH
The VSWH pin is the connection of the drain and source of the internal NMOS switches. At switch off, the
inductor will drive this pin below ground as the body diode and the NMOS conducts with a high dv/dt.
16−28, 37
PGND
Ground reference and high−current return path for the bottom gate driver and low- side NMOS.
35
VSW
IC connection to the switch node between the top MOSFET and bottom MOSFET. Return path of the high−
side gate driver.
36
BST
Top gate driver input supply, a bootstrap capacitor connection between the switch node and this pin.
38
VB
The internal LDO output and input supply for the NCP3231. Connect a minimum of 4.7 mF ceramic capacitor
from this pin to ground.
39
VCC
Input Supply for IC. This pin must be connected to VIN. Decouple the VCC pin close to ground near the pin
of the device.
40
EN
Logic control for enabling the switcher. An internal pull−up enables the device automatically. The EN pin can
also be driven high to turn on the device, or low to turn off the device. A comparator and precision reference
allow the user to implement this pin as an adjustable UVLO circuit.
EP41
GND
Output of the error amplifier.
A resistor from this pin to ground sets the over−current protection (OCP) threshold.
Analog ground.
Negative input of internal thermal comparator. Tie this pin to ground if not in use.
Exposed Pad. Connect GND to a large copper plane at ground potential to improve thermal dissipation.
www.onsemi.com
3
NCP3231
VIN
VIN
BST
VCC
VOUT
VSWH
VSW
VB
PGND
NCP3231
ISET
AGND
VPG
EN
FB
OTS
PG
COMP
SS
Figure 2. Typical Application Circuit
ABSOLUTE MAXIMUM RATINGS (measured vs. GND pads, unless otherwise noted)
Rating
Symbol
Value
Unit
VIN, VCC
20.5
−0.3
V
VSW to GND
VSWH, VSW
26
−0.6 (DC)
30 (t < 50 ns)
−4 (t < 100 ns)
V
BST to GND
BST
30 (DC)
−0.6 (DC)
32 (t < 50 ns)
V
6.0
−0.3
V
Power Supply to GND
All other pins
Operating Ambient Temperature Range (Note 1)
TA
−40 to +85
°C
Operating Junction Temperature Range (Note 1)
TJ
−40 to +125
°C
TJ(MAX)
+150
°C
Tstg
−55 to +150
°C
HS FET Junction−to−Case Thermal Resistance (Note 2)
RqJC−HS
1.3
°C/W
LS FET Junction−to−Case Thermal Resistance (Note 2)
RqJC−LS
0.6
°C/W
Maximum Junction Temperature
Storage Temperature Range
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. The maximum package power dissipation limit must not be exceeded.
PD +
T J(MAX) * T A
R qJA
2. RqJC thermal resistance is obtained by simulating a cold plate test on the exposed power pad. No specific JEDEC standard test exists, but
a close description can be found in the ANSI SEMI standard G30−88.
www.onsemi.com
4
NCP3231
ELECTRICAL CHARACTERISTICS
(−40°C < TJ < +125°C, VCC = 12 V, for min/max values unless otherwise noted, TJ = +25°C for typical values)
Parameter
Symbol
Test Conditions
Min
Typ
Max
Units
18
V
POWER SUPPLY
VIN/VCC Operation Voltage
VIN/VCC
4.5
VB UVLO Threshold (Rising)
4.1
4.2
4.3
V
VB UVLO Threshold (Falling)
3.4
3.66
3.8
V
4.9
5.15
5.45
V
IB = 25 mA, VCC = 4.5 V
36
110
mV
EN = H, COMP = H, no switching;
PG open; no switching
4.7
6.1
mA
NCP3231; EN = 0; VCC = 18 V; PG open
100
140
mA
NCP3231; EN = 0; VCC = 4.5 V; PG open
53
70
mA
V
VB Output Voltage
VB
VB Dropout Voltage
VCC Quiescent Current
Shutdown Supply Current
VCC = 6 V, 0 ≤ IB ≤ 40 mA
FEEDBACK VOLTAGE
FB Input Voltage
VFB
Feedback Input Bias Current
IFB
TJ = 25°C, 4.5 V ≤ VCC ≤ 18 V
0.597
0.6
0.603
−40°C ≤ TJ ≤ 125°C; 4.5 V ≤ VCC ≤ 18 V
0.594
0.6
0.606
VFB = 0.6 V
75
nA
ERROR AMPLIFIER
60
Open Loop DC Gain (Note 4)
Open Loop Unity Gain Bandwidth
F0dB,EA
Open Loop Phase Margin
Slew Rate
COMP pin to GND = 10 pF
COMP Clamp Voltage, High
COMP Clamp Voltage, Low
85
dB
24
MHz
60
°
2.5
V/m
3.46
V
465
mV
Output Source Current
VFB = 0 V
15
mA
Output Sink Current
VFB = 1 V
20
mA
Sourced from ISET pin, before SS,
TJ = 25°C
30.5
CURRENT LIMIT
Low−side ISET Current Source
LS_ISET
Low−side ISET Current Source
Temperature Coefficient
TC_LS_I−
SET
Low−side OCP Switch−over
Threshold (Note 4)
Low−side Fixed OCP Threshold
(Note 4)
LS_OCPth
Low−side Programmable OCP Range
LS_OCPth
LS OCP Blanking time (Note 4)
LS_Tblnk
33
35.5
mA
+0.31
%/°C
600
mV
300
mV
< 600
mV
150
ns
92
%
PWM
Maximum duty cycle
fsw = 500 kHz, VFB = 0 V
4.5 V < VCC < 18 V
Minimum duty cycle
VCOMP < PWM Ramp Offset Voltage
0
%
Minimum GH on−time (Note 3)
60
ns
PWM Ramp Amplitude (Note 3)
VCC/8.6 VCC/6.6 VCC/5.6
V
0.64
V
PWM Ramp Offset (Note 3)
3. Guaranteed by characterization
4. Guaranteed by design
www.onsemi.com
5
NCP3231
ELECTRICAL CHARACTERISTICS
(−40°C < TJ < +125°C, VCC = 12 V, for min/max values unless otherwise noted, TJ = +25°C for typical values)
Parameter
Symbol
Test Conditions
Min
Typ
Max
Units
fsw
fsw = 500 kHz
4.5 V < VCC < 18 V
450
500
550
kHz
thiccup
tss < 1 ms, fsw = 500 kHz
4
ms
tss > 1 ms, fsw = 500 kHz
4 x tss
ms
OSCILLATOR
Oscillator Frequency Range
Hiccup Timer
ENABLE INPUT (EN)
EN Input Operating Range
Enable Threshold Voltage
VEN rising
Enable Hysteresis
VEN falling
Deep Disable Threshold
1.11
1.2
5.5
V
1.29
V
144
0.7
Enable Pull−up Current
0.78
mV
0.9
V
2
mA
SOFTSTART INPUT (SS)
SS Startup Delay
tSSD
1.33
ms
SS End Threshold
SSEND
0.6
V
SS Source Current
ISS
2.15
2.5
2.8
mA
10
20
30
mA
665
675
685
mV
VOLTAGE MONITOR
PG = 0.15 V
Power Good Sink Current
Output Overvoltage Rising Threshold
Overvoltage Fault Blanking Time
ms
20
Output Under−Voltage Trip Threshold
500
525
550
mV
Under−voltage Protection Blanking
Time
20
ms
OVP and UVP Enable Delay
tSS
s
POWER STAGE
High−side On Resistance
RDSONH
VGS = 5 V, ID = 2 A
Low−side On Resistance
RDSONL
VFBOOT
7
9.9
mW
VGS = VB, ID = 2 A
1.5
2.9
mW
IBOOT = 2 mA
0.28
V
THERMAL MONITOR (OTS)
0.59
OTS comparator reference voltage
(Rising Threshold)
OTS comparator reference voltage
(Falling Hysteresis) (Note 3)
0.6
0.61
V
50
mV
Thermal Shutdown Threshold
150
°C
Thermal Shutdown Hysteresis
25
°C
THERMAL SHUTDOWN
3. Guaranteed by characterization
4. Guaranteed by design
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
6
NCP3231
fSW, SWITCHING FREQUENCY (kHz)
0.602
0.601
0.600
0.599
0.598
0.597
0.596
−40 −25 −10
5
20
35
50
65
80
95 110 125
503
VCC = 12 V
502
501
500
VCC = 4.5 V
499
498
−40 −25 −10
5
20
35
50
65
80
95 110 125
TJ, JUNCTION TEMPERATURE (°C)
Figure 3. Reference Voltage vs. Temperature
Figure 4. Switching Frequency vs.
Temperature
1.23
1.22
1.21
1.20
1.19
−40 −25 −10
5
20
35
50
65
80
95 110 125
1.10
1.09
1.08
1.07
1.06
−40 −25 −10
5
20
35
50
65
80
95 110 125
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 5. Rising Enable Threshold vs.
Temperature
Figure 6. Falling Enable Threshold vs.
Temperature
7
100
90
IQ, QUIESCENT CURRENT (mA)
ISD, SHUTDOWN CURRENT (mA)
504
TJ, JUNCTION TEMPERATURE (°C)
VEN, FALLING ENABLE THRESHOLD (V)
VEN, RISING ENABLE THRESHOLD (V)
VFB, FEEDBACK REFERENCE VOLTAGE (V)
TYPICAL CHARACTERISTICS
80
70
60
50
40
30
20
VCC = 12 V
10
0
−40 −25 −10
5
20
35
50
65
80
6
5
4
3
2
1
VCC = 12 V, No Switching
0
−40 −25 −10
95 110 125
5
20
35
50
65
80
95 110 125
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 7. Shutdown Current vs. Temperature
Figure 8. Quiescent Current vs. Temperature
www.onsemi.com
7
NCP3231
TYPICAL CHARACTERISTICS
50
ISET, LSOCP SET CURRENT (mA)
ISS, SOFT−START CURRENT (mA)
2.70
2.65
2.60
2.55
2.50
2.45
2.40
2.35
2.30
−40 −25 −10
5
20
35
50
65
80
40
35
30
25
20
−40 −25 −10
95 110 125
5
20
35
50
65
80
95 110 125
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 9. Soft−start Current vs. Temperature
Figure 10. ISET Current vs. Temperature
9.5
2.5
9.0
LOW−SIDE FET RDS(on) (mW)
HIGH−SIDE FET RDS(on) (mW)
45
8.5
VIN/VCC = 4.5 V
8.0
7.5
VIN/VCC = 12 V
7.0
6.5
6.0
5.5
5.0
−40 −25 −10
5
20
35
50
65
80
95
2.0
VIN/VCC = 4.5 V
1.5
VIN/VCC = 12 V
1.0
0.5
0
−40 −25 −10
110 125
5
20
35
50
65
80
95 110 125
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 11. High−side RDS(on) vs. Temperature
Figure 12. Low−side RDS(on) vs. Temperature
100
100
VOUT = 3.3 V
95
VOUT = 3.3 V
95
85
EFFICIENCY (%)
EFFICIENCY (%)
90
VOUT = 1.0 V
80
VOUT = 2.5 V
75
VOUT = 1.8 V
70
VOUT = 1.2 V
65
90
85
VOUT = 2.5 V
VOUT = 1.0 V
VOUT = 1.8 V
80
VOUT = 1.2 V
75
70
60
VIN/VCC = 12 V
TA = 25°C
55
50
VIN/VCC = 5 V
TA = 25°C
65
60
0
2.5
5.0
0
7.5 10.0 12.5 15.0 17.5 20.0 22.5 25.0
2.5
5.0
7.5 10.0 12.5 15.0 17.5 20.0 22.5 25.0
IOUT, LOAD CURRENT (A)
IOUT, LOAD CURRENT (A)
Figure 13. Efficiency vs. Iout
(Vin = 12 V)
Figure 14. Efficiency vs. Iout
(Vin = 5 V)
www.onsemi.com
8
NCP3231
TYPICAL CHARACTERISTICS
0.61
4.30
0.60
0.59
0.58
0.57
0.56
Falling Threshold
0.55
0.54
−40 −25 −10
5
20
35
50
65
80
4.26
4.22
4.18
4.14
4.10
−40 −25 −10
95 110 125
5
20
35
50
65
80
95 110 125
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 15. OTS Threshold vs. Temperature
Figure 16. VB UVLO Rising Threshold vs.
Junction Temperature
OVP, OVERVOLTAGE THRESHOLD (mV)
3.80
3.76
3.72
3.68
3.64
3.60
−40 −25 −10
5
20
35
50
65
80
95 110 125
680
679
678
677
676
675
674
673
672
671
670
−40 −25 −10
5
20
35
50
65
80
95 110 125
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 17. VB UVLO Falling Threshold vs.
Junction Temperature
Figure 18. Output OVP vs. Junction
Temperature
UVP, UNDERVOLTAGE THRESHOLD (mV)
VB UVLO, FALLING THRESHOLD VOLTAGE (V)
VB UVLO RISING THRESHOLD
VOLTAGE (V)
OTS, OVERTEMPERATURE
THRESHOLD VOLTAGE (V)
Rising Threshold
560
558
556
554
552
550
548
546
544
542
540
−40 −25 −10
5
20
35
50
65
80
95 110 125
TJ, JUNCTION TEMPERATURE (°C)
Figure 19. Output UVP vs. Junction
Temperature
www.onsemi.com
9
NCP3231
TYPICAL CHARACTERISTICS
CH1 (Blue): EN
CH2 (Aqua): COMP
CH3 (Purple): Vout
CH4 (Green): SS
CH1 (Blue): VSW
CH2 (Aqua): COMP
CH3 (Purple): Vout
CH4 (Green): SS
Figure 20. Typical Startup Waveforms
(Vin = 12 V, Iout = 25 A, Vout = 1 V)
Figure 21. Typical Short Circuit Waveforms
(Vin = 12 V)
www.onsemi.com
10
NCP3231
OPERATION DESCRIPTION
Overview
Adaptive Non−Overlap Gate Driver
The NCP3231 is a 500 kHz, high efficiency, high current
PWM synchronous buck converter. It operates with a single
supply voltage from 4.5 to 18 V and can provide output
current as high as 30 A. NCP3231 utilizes voltage mode with
voltage feed−forward control to respond instantly to Vin
changes and provide for easier compensation over the
supply range of the converter. The device also includes
pre−bias startup capability to allow monotonic startup in the
event of a pre−biased output condition.
Protection features include overcurrent protection (OCP),
output over and under voltage protection (OVP, UVP), and
power good. The enable function is highly programmable to
allow for adjustable startup voltages at higher input
voltages. There is also an adjustable soft−start, an over−
temperature comparator, and internal thermal shutdown.
In a synchronous buck converter, a certain dead time is
required between the low side drive signal and high side
drive signal to avoid shoot through. During the dead time,
the body diode of the low side FET freewheels the current.
NCP3231 implements adaptive dead time control to
minimize the dead time, as well as preventing shoot through.
Precision Enable (EN)
The ENABLE block allows the output to be toggled on
and off and is a precision analog input.
When the EN voltage exceeds V_EN, the controller will
initiate the soft−start sequence as long as the input voltage
and sub−regulated voltage have exceeded their UVLO
thresholds. V_EN_hyst helps to reject noise and allow the
pin to be resistively coupled to the input voltage or
sequenced with other rails.
If the EN voltage is held below typically 0.8 V, the
NCP3231 enters a deep disable state where the internal bias
circuitry is off. As the voltage at EN continues to rise, the
Enable comparator and reference are active and provide a
more accurate EN threshold. The drivers are held off until
the rising voltage at EN crosses V_EN.
An internal 2 mA pullup automatically enables the device
when the EN pin is left floating.
Reference Voltage
The NCP3231 incorporates an internal reference that
allows output voltages as low as 0.6 V. The tolerance of the
internal reference is guaranteed over the entire operating
temperature range of the controller. The reference voltage is
trimmed using a test configuration that accounts for error
amplifier offset and bias currents.
Oscillator Ramp
The ramp waveform is a saw tooth formed at the PWM
frequency with a peak−to−peak amplitude of VCC/6.6,
offset from GND by typically 0.64 V. The PWM duty cycle
is limited to a typical 92%, allowing the bootstrap capacitor
to charge during each cycle.
INPUT SUPPLY / VCC
VDD
2 mA
EN
Error Amplifier
The error amplifier’s primary function is to regulate the
converter’s output voltage using a resistor divider connected
from the converter’s output to the FB pin of the controller,
as shown in the Applications Schematic. A type III
compensation network must be connected around the error
amplifier to stabilize the converter. It has a bandwidth of
greater than 24 MHz, with open loop gain of at least 60 dB.
1.2 V
Figure 22. Enable Functional Block Diagram
Pre−bias Startup
In some applications the controller will be required to start
switching when its output capacitors are charged anywhere
from slightly above 0 V to just below the regulation voltage.
This situation occurs for a number of reasons: the
converter’s output capacitors may have residual charge on
them or the converter’s output may be held up by a low
current standby power supply. NCP3231 supports pre−bias
start up by holding off switching until the feedback voltage
and thus the output voltage rises above the set regulated
voltage. If the pre−bias voltage is higher than the set
regulated voltage, switching does not occur until the output
voltage drops back to the regulation point.
Programmable Soft−Start
An external capacitor connected from the SS pin to
ground sets up the soft start period, which can limit the
start−up inrush current. The soft start period can be
programmed based on the Equation 1.
t SS +
V ref
C SS
I SS
Enable
Logic
(eq. 1)
OCP is the only fault that is active during a soft−start.
www.onsemi.com
11
NCP3231
Power Good (PG) Operation
Power Good Pullup Voltage
LSOCP Trip Level
Inductor Current
Start
Reset/Start
Reset/Start
Backup Counter
Start
Hiccup
Hiccup Counter
1
2
3
tHiccup = 4xtSS
Skipped Pulses showing Skip Count
Figure 23. LSOCP Function with Counters and Power Good Shown (exaggerated for informational purposes)
www.onsemi.com
12
NCP3231
PROTECTION FEATURES
Hiccup Mode
Over Current Protection Threshold (ISET)
The NCP3231 utilizes hiccup mode for all of its fault
conditions. Upon entering hiccup mode after a fault
detection, the NCP3231 turns off the high side and low side
FET’s and PG goes low. It waits for tHICCUP ms before
reinitiating a soft−start. tHiccup is defined as four soft start
timeouts (tss). The equation for tss is shown in Equation 1.
OCP is the only active fault detection during the hiccup
mode soft start.
The NCP3231 allows the user to adjust the LSOCP
threshold with an external resistor, RSET. This resistor,
along with an internal temperature compensated current
source, ISET, sets the current limit reference voltage for the
LSOCP comparator.
Internally, a current sense circuit samples the voltage from
VSW to GND. This voltage is then multiplied by a factor of
2X and compared against the ISET*RSET voltage
threshold.
The basic design equation for LSOCP trip point selection is:
Over Temperature Comparator (OTS)
The NCP3231 provides an over−temperature shutdown
(OTS) comparator with 50 mV hysteresis and a 0.6 V
reference in order to remotely sense an external temperature
detector or thermistor. When the voltage at the OTS pin rises
above 0.6 V, the drivers stop switching and both FET’s
remain off. When this voltage drops below typically 0.55 V,
a new soft−start cycle is generated automatically. Tie the
OTS pin to ground if this function is not required.
(eq. 2)
RSET +
2 LSOCP RDSON (1 ) TC RDS DTJ Control)
ISET TC ISET (1 ) TC RDS DTJ LSFET)
Where:
LSOCP is the targeted LSOCP trip point after 150 ns
blanking from the peak current
ISET is typically 33 mA current sourcing from the ISET pin
into the RSET resistor
RDSON is the RDSON of the LSFET
TCRDS is the change in RDSON vs. temperature
TCISET is the change in ISET vs. temperature
DTJIC is the change in junction temperature from 255C of
the NCP3231 control block
DTJLSFET is the change in junction temperature from 255C
of the LSFET
There will also be an error due to the blanking time as the
inductor current falls during the off time. It can be
approximated from the following equation:
Over Voltage Protection (OVP)
When the voltage at the FB pin (VFB) is above the OVP
threshold for greater than 20 ms (typical), an OVP fault is set.
The high side FET (HSFET) will turn off and the low side
FET (LSFET) will turn on. The open-drain PG pull down
will turn on at that point as well, thus pulling PG low. Once
VFB has fallen below the Undervoltage Protection
Threshold (UVP), the device will enter hiccup mode.
Under Voltage Protection (UVP)
A UVP circuit monitors the VFB voltage to detect an
under voltage event. If the VFB voltage is below this
threshold for more than 20 ms, a UVP fault is set and the
device will enter hiccup mode.
OCPoffset +
Over Current Protection (OCP)
The NCP3231 over current protection scheme senses the
peak freewheeling current in the low−side FET (LSOCP)
after a blanking time of 150 ns as shown in Figure 23. The
low−side FET drain−to−source voltage, VDS, is compared
against the voltage of a fixed, internal current source, ISET
and a user−selected resistor, RSET. Voltage across the
low−side FET is sensed from the VSW pin to GND.
After an OCP detection, the NCP3231 keeps the
high−side FET off until the Low−side FET current falls
below the trip point again and the next clock cycle occurs.
An internal OCP counter will count up to 3 consecutive
LSOCP events. After the third consecutive count, the device
enters hiccup mode.
To prevent nuisance trips, there is a backup counter that
will reset the OCP counter after 7 consecutive cycles without
an LSOCP trigger. The backup counter is reset and then
started again after each OCP trip until the third OCP count
as stated above occurs.
ǒ
Ǔ
Vout OCP
@ ǒtblank LSǓ
L
(eq. 3)
Where:
VoutOCP is the output voltage during an overcurrent event.
tblankLS is the LSOCP blanking time which is typically
150 ns.
Therefore:
Ipeak + LSOCP ) OCPoffset
(eq. 4)
The ISET threshold has a typical value of 33 mA with a
typical temperature coefficient of 0.31%/oC.
The LSFET has a typical RDSon of 2 mW, and a
temperature coefficient of 0.35%/°C.
In case RSET is not connected, the device switches the
OCP threshold to a fixed 300 mV value: an internal safety
clamp on ISET is triggered as soon as the ISET voltage
reaches 600 mV, enabling the 300 mV fixed threshold.
www.onsemi.com
13
NCP3231
Thermal Shutdown (TSD)
Via Placement for Power and Ground
The NCP3231 protects itself from overheating with an
internal thermal monitoring circuit. If the junction
temperature exceeds the thermal shutdown threshold both
the upper and lower MOSFETs will be shut OFF. Once the
temperature drops below the falling hysteresis threshold, the
voltage at the COMP pin will be pulled below the ramp
valley voltage and a soft−start will be initiated.
Place enough vias to adequately connect outer layers to
inner layers for thermal transfer and to minimize added
inductance in layer transition. Multiple vias should be
placed near important components like input ceramics and
output ceramic capacitors.
Key Signal Routes
Do not route sensitive signals, such as FB, near or under
noisy nets such as the switch node, VSW, to reduce noise
coupling on the sensitive lines.
Power Good Monitor (PG)
NCP3231 monitors the output voltage and signal when the
output is out of regulation or during a non−regulated pre−bias
condition, or fault condition. When the output voltage is
within the OVP and UVP thresholds, the power good pin is
a high impedance output. If the NCP3231 detects an OCP,
OVP, UVP, OTS, TSD or is in soft start, it pulls PG pin low.
The PG pin is an open drain 10−mA pull down output.
Thermal Copper Shapes
Duplicate and extend shapes from Component Layers to
improve thermal performance.
To improve the Low−side OCP accuracy, users should use
single ground connection instead of separate analog ground
and power ground. Make sure that the inner layers (at least
2nd layer, 3rd layer and 4th layer) are dedicated for ground
plane. Do not use other copper planes to break or interrupt
the shape of ground plane, which may add more parasitic
components to affect the sensing accuracy.
Thermal management consideration: the major heat flow
path from package to the ambient is through the copper on
the PCB, the area and thickness of copper plane affect the
themeral performance; maximize the copper coverage on all
the layers to increase the effective thermal conductivity of
the board. This is importatnt especially when there is no heat
sinks attached to the PCB on the other side of the package;
add as many thermal vias as possible directly under the
package ground pad to maximize the effective out−of−plane
thermal conductivity of the board; all the thermal vias must
be either plated (copper) shut or plugged and capped on both
sides of the board. This prevents solder seeping in to the
thermal vias causing solder voids. Solder voides are higher
detrimental to the thermal and electrical performance of the
package; to ensure reliability and performance, the solder
coverage should be at least 85 percent. This means the total
voids on the ground pad should be less than 15 percent with
no single void larger than 1 mm. Several smaller voids are
always better than a few big voids.
Layout Guidelines
When laying out a power PCB for the NCP3231 there are
several key points to consider.
Base Component Placement
High current path components should be placed to keep
the current path as tight as possible. Placement of
components on the bottom of the board such as input or
output decoupling can add loop inductance.
Ground Return for Power and Signals
Solid, uninterrupted ground planes must be present and
adjacent to the high current path.
Copper Shapes on Component Layers
Large copper planes on one or multiple layers with adequate
vias will increase thermal transfer, reduce copper conduction
losses, and minimize loop inductance. Greater than 20 A
designs require 2−3 layer shapes or more, increasing the
number of layers will only improve performance. This
applies to input, output, and switch node shapes.
www.onsemi.com
14
NCP3231
PACKAGE DIMENSIONS
QFN40 6x6, 0.5P
CASE 485CM
ISSUE O
A B
D
PIN ONE
LOCATION
2X
ÉÉÉ
ÉÉÉ
ÉÉÉ
L1
DETAIL A
ALTERNATE
CONSTRUCTIONS
E
ÉÉ
ÉÉ
0.15 C
EXPOSED Cu
2X
TOP VIEW
0.15 C
(A3)
DETAIL B
0.10 C
DIM
A
A1
A3
b
D
D2
D3
E
E2
E3
E4
e
G
K
L
L1
MOLD CMPD
DETAIL B
ALTERNATE
CONSTRUCTION
A
43X
0.08 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSIONS: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30mm FROM TERMINAL
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
5. POSITIONAL TOLERANCE APPLIES TO ALL
THREE EXPOSED PADS.
L
L
SIDE VIEW A1
C
NOTE 4
SEATING
PLANE
0.10 C A B
D3
D2
NOTE 5
G
DETAIL A
40X
L
MILLIMETERS
MIN
MAX
0.80
1.00
−−−
0.05
0.20 REF
0.18
0.30
6.00 BSC
2.30
2.50
1.40
1.60
6.00 BSC
4.30
4.50
1.90
2.10
1.64
1.84
0.50 BSC
2.20 BSC
0.20
−−−
0.30
0.50
−−−
0.15
SOLDERING FOOTPRINT
E3
6.30
E2
4.56
E4
1.66
1
G
40
K
e
40X
e/2
G
BOTTOM VIEW
40X
0.63
2.56
1
b
0.10 C A B
0.05 C
2.16
NOTE 3
4.56
6.30
2.16
PKG
OUTLINE
40X
0.50
PITCH
0.30
DIMENSIONS: MILLIMETERS
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
15
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP3231/D