NCV7424 D

NCV7424
Four Channel LIN
Transceiver
NCV7424 is a four channel physical layer device using the Local
Interconnect Network (LIN) protocol. It allows interfacing of four
independent LIN physical buses and the LIN protocol controllers. The
device is compliant to LIN 2.x Protocol Specification package and the
SAE J2602 standard.
The NCV7424 LIN device is a member of the in-vehicle networking
(IVN) transceiver family. The device is a monolithic solution
incorporating 4 times the NCV7321-1 transceiver.
www.onsemi.com
16
1
Features
TSSOP−16
CASE 948F
• TSSOP−16 Package. Pin-out Compatible with One Single LIN
•
•
•
•
•
•
•
•
•
•
•
NCV7321 Transceiver (Pin Numbers 4 to 7, and 10 to 13)
Compliant with LIN2.x, Backwards Compatible to Version 1.3 and
J2602
Transmission Rate 1 kbps to 20 kbps
Indefinite Short-Circuit Protection on LIN towards Supply and
Ground
Bus Pins Protected Against Transients in an Automotive
Environment
Thermal Shutdown
System ESD on LIN Pin Exceeding 10 kV, No Need for External
ESD Protections
Load Dump Protection (45 V)
Integrated Slope Control Resulting into Excellent EME Performance
also without any Capacitor on LIN Pin
Excellent EMI Performance
Remote Wake-up via LIN Bus on all Four Channels
3.3 V and 5 V Compatible Digital Inputs
NCV7424
TxD4
RxD3
TxD3
RxD1
EN
TxD2
TxD1
RxD2
16
1
TSSOP−16
8
9
RxD4
LIN4
GND
LIN3
VBB
LIN1
GND
LIN2
MARKING DIAGRAM
16
NV74
24−0
ALYWG
G
1
Quality
• NCV Prefix for Automotive and Other Applications Requiring
•
PACKAGE PICTURE
Unique Site and Control Change Require− ments; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
NV7424−0 = Specific Device Code
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W
= Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering, marking and shipping information in the
package dimensions section on page 11 of this data sheet.
© Semiconductor Components Industries, LLC, 2015
May, 2015 − Rev. 2
1
Publication Order Number:
NCV7424/D
NCV7424
BLOCK DIAGRAM
NCV7424
VBB
Undervoltage
POR
State
&
Wake−up
Control
EN
VINT
Osc
GND
Thermal
Shutdown
Timeouts
GND
RxD1
COMP
Vint
Filter
Driver
Control
TxD1
LIN1
Slope
Control
Channel1
RxD2
TxD2
RxD3
TxD3
RxD4
TxD4
Channel2
LIN2
Channel3
LIN3
Channel4
LIN4
RB20111020.1
Figure 1. Block Diagram
www.onsemi.com
2
NCV7424
Table 1. KEY TECHNICAL CHARACTERISTICS AND OPERATING RANGES
Symbol
VBB
Parameter
Nominal Battery Operating Voltage (Note 1)
Min
Typ
Max
Unit
5
12
27
V
Load Dump Protection
45
30
mA
−45
45
V
0
5.5
V
185
°C
125
°C
−4
4
kV
−10
10
kV
IBB_SLP
Supply Current in Sleep Mode, VBB = 12 V, TJ < 85°C VLINx = VBB
10
VLIN
LIN Bus Voltage
V_Dig_IO
Operating DC Voltage on Digital IO Pins (EN, RxD1-4, TxD1-4)
TJ
Junction Thermal Shutdown Temperature
150
Tamb
Operating Ambient Temperature
−40
VESD
Electrostatic Discharge Voltage (all pins) Human Body Model (Note 2)
Conform to EIA−JESD22−A114−B
Electrostatic Discharge Voltage (LIN) System Human Body Model (Note 3)
Conform to EIC 61000−4−2
165
1. Below 5 V on VBB in normal mode, the bus will either stay recessive or comply with the voltage level specifications and transition time
specifications as required by SAE J2602. It is ensured by the battery monitoring circuit. Above 27 V on VBB, LIN communication is operational
(LIN pin toggling) but parameters cannot be guaranteed. For higher battery voltage operation above 27 V, LIN pull-up resistor must be
selected large enough to avoid clamping of LIN pin by voltage drop over external pull-up resistor and LIN pin min current limitation.
2. Equivalent to discharging a 100 pF capacitor through a 1.5 kW resistor.
3. Equivalent to discharging a 150 pF capacitor through a 330 W resistor. System HBM levels are verified by an external test−house.
Table 2. PIN FUNCTION DESCRIPTION
Pin
Name
Description
1
TxD4
Transmit Data Input, Low for Dominant State; Pull-up to internal supply guaranteed above pin input threshold
2
RxD3
Receive Data Output; Low in Dominant State
3
TxD3
Transmit Data Input, Low for Dominant State; Pull-up to internal supply guaranteed above pin input threshold
4
RxD1
Receive Data Output; Low in Dominant State
5
EN
6
TxD2
Enable Input, Transceiver in Normal Operation Mode when High, Pull-down Resistor to GND
Transmit Data Input, Low for Dominant State; Pull-up to internal supply guaranteed above pin input threshold
7
TxD1
Transmit Data Input, Low for Dominant State; Pull-up to internal supply guaranteed above pin input threshold
8
RxD2
Receive Data Output; Low in Dominant State
9
LIN2
LIN Bus Output/Input
10
GND
Ground
11
LIN1
LIN Bus Output/Input
12
VBB
Battery Supply Input
13
LIN3
LIN Bus Output/Input
14
GND
Ground
15
LIN4
LIN Bus Output/Input
16
RxD4
Receive Data Output; Low in Dominant State
www.onsemi.com
3
NCV7424
TYPICAL APPLICATION
VBAT
VBB
VCC
2.7 V to
5V
4
5.1k
1k
VBB
4
RxDx
4
LINx
4
4
Micro
4
LINx
TxDx
controller
NCV7424
EN
1nF
GND
GND
GND
GND
RB 20111103
4
KL30
LIN BUS
1,2,3,4
KL31
Figure 2. Application Diagram, Four LIN Master Nodes
Table 3. ABSOLUTE MAXIMUM RATINGS
Max
Unit
VBB
Symbol
Voltage on Pin VBB
Parameter
−0.3
Min
Typ
45
V
VLINx
LINx Bus Voltage (LIN1-4)
−45
45
V
V_Dig_IO
DC Input Voltage on Pins (EN, RxD1-4, TxD1-4)
−0.3
7
V
TJ
Maximum Junction Temperature
−40
150
°C
VESD
HBM (All Pins) (Note 4)
Conform to EIA−JESD22−A114−B
−4
4
kV
CDM (All Pins)
According to ESD STM 5.3.1−1999
−750
750
V
HBM (LINx and VBB) (Note 4)
−8
8
kV
System HBM (LINx and VBB) (Note 5)
Conform to EIC 61000−4−2
−10
10
kV
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
4. Equivalent to discharging a 100 pF capacitor through a 1.5 kW resistor.
5. Equivalent to discharging a 150 pF capacitor through a 330 W resistor. System HBM levels are verified by an external test−house.
www.onsemi.com
4
NCV7424
Table 4. THERMAL CHARACTERISTICS
Symbol
Parameter
Conditions
Value
Unit
RqJA_1
Thermal Resistance Junction−to−Air, JESD51-3 1S0P PCB
Free air
128
K/W
RqJA_2
Thermal Resistance Junction−to−Air, JESD51-7 2S2P PCB
Free air
72
K/W
FUNCTIONAL DESCRIPTION
Overall Functional Description
excellent EMC performance due to reduced slew rate of the
LIN outputs.
The junction temperature is monitored via a thermal
shutdown circuit that switches the LIN transmitters off when
temperature exceeds the TSD trigger level.
The NCV7424 has four operating states (unpowered
mode, standby mode, normal mode and sleep mode) that are
determined by the supply voltage VBB, input signals EN and
activity on the LIN bus. The operating states and principal
transitions between them are depicted in Figure 3.
LIN is a serial communication protocol that efficiently
supports the control of mechatronic nodes in distributed
automotive applications. The domain is class-A multiplex
buses with a single master node and a set of slave nodes.
The NCV7424 contains four independent LIN
transmitters, LIN receivers plus common battery
monitoring, power-on-reset (POR) circuits and thermal
shutdown (TSD). The used LIN transmitter is optimized for
the maximum specified transmission speed of 20 kbps with
OPERATING STATES
Standby mode
Normal mode
EN = High
− LIN transceivers: OFF
− LIN term: 30 kW
− RxD1, 2, 3, 4:
Low to indicate wake−up on
bus
− LIN transceivers: ON
− LIN term: 30 kW
− RxD1, 2, 3, 4:
Received LIN data
for t > tenable
EN = High for t > tenable
LIN1, 2, 3 or 4 wakeup
EN = Low for t > tdisable
Unpowered
(VBB Below Reset Level)
− LIN transceivers: OFF
− LIN term: floating
− RxD1, 2, 3, 4: floating
Sleep Mode
− LIN transceivers: OFF
− LIN term: current source
− RxD1, 2, 3, 4: floating
VBB above reset level
Figure 3. State Diagram
Unpowered Mode
As long as VBB remains below its power-on-reset level,
the chip is kept in a safe unpowered state. LIN transmitters
are inactive, LINx pins are left floating. Pins RxDx remain
floating.
The unpowered state will be entered from any other state
when VBB falls below its power-on-reset level.
sleep mode, the RxD1,2,3 or 4 pin is pulled low depending
on which of the respective pins LIN1,2,3 or 4 the valid LIN
wake-up occurred. While staying in standby mode, wake-up
signaling by RxDx pins on each LIN channel is fully
functional. This is also in case if wake event(s) started in
sleep mode but actual transition from sleep to standby was
caused by preceding wake-up event on other LIN channel.
Standby Mode
Normal Mode
Standby mode is a low-power mode, where the LIN
transceivers remain inactive. A 30 kW resistor in series with
a reverse-protection diode is internally connected between
individual LIN pins and pin VBB. Standby mode is entered
after a wake-up event is recognized while the chip was in the
In normal mode, the full functionality of the LIN
transceivers is available. Data are sent to the LINx bus
according to the state of TxDx inputs and RxDx pins reflect
the logical symbol received on the LINx bus –
high-impedant for recessive and Low level for dominant.
www.onsemi.com
5
NCV7424
Normal mode can be entered from either standby or sleep
mode when EN Pin is High for longer than tenable. When the
transition is made from standby mode, RxDx is put
high-impedant immediately after EN becomes High (before
the expiration of tenable filtering time). Transmission on each
LINx channel is only possible for particular TxDx pin
starting from High to Low level (if TxDx pin is Low when
entering Normal mode, transmission is not enabled).
A 30 kW resistor in series with a reverse-protection diode is
internally connected between LIN and VBB pins.
To avoid that, due to a failure of the application (e.g.
software error, a short to ground, etc.), the LIN bus is
permanently driven dominant and thus blocking all
subsequent communication, the signal on each TxDx pin
passes through an independent timer per LIN channel, which
releases the bus in case TxDx remains
Low for longer than tTxD_timeout. The transmission can
continue once the TxDx returns to High logical level. This
is independent on each channel, means permanent dominant
on one channel is not blocking the other channels from
communication.
In case the junction temperature increases above the
thermal shutdown threshold, e.g. due to a short of the LIN
wiring to the battery and high ambient temperature, all four
transmitters are disabled and LIN buses are kept in recessive
state independently of TxDx inputs. RxDx pins are kept Low
during thermal shutdown.
Once the junction temperature decreases below the
thermal shutdown release level, the transmission is enabled
again. RxD pins are released from asserted thermal
shutdown low level immediately when chip is below
thermal shutdown threshold.
As required by SAE J2602, the transceiver behaves safely
below its operating range – it either continues to transmit
correctly (according to its specification) or remains silent
(transmits a recessive state regardless of the TxDx signal).
A battery monitoring circuit in NCV7424 deactivates the
transmitter in normal mode if the VBB level drops below
MONL_VBB. Transmission is enabled again when VBB
reaches MONH_VBB. The internal logic remains in normal
mode and the reception from the LIN line is still possible
even if the battery monitor disables the transmission.
Although the specifications of the monitoring and
power-on-reset levels are overlapping, it is ensured by the
implementation that the monitoring level never falls below
the power-on-reset level.
Sleep Mode
Sleep mode provides extremely low current consumption.
The LIN transceiver is inactive and the battery consumption
is minimized. Only a weak pull-up current source is
internally connected between LIN and VBB pins, in order to
minimize current consumption even in case of LIN short to
GND.
Sleep mode can be entered:
• After the voltage level at VBB pin rises above its
power-on-reset level. RxDx pins are set high-impedant
after start-up
• From normal mode by assigning a Low logical level to
pin EN for longer than tdisable. The sleep mode can be
entered even if a permanent short occurs on the LINx
Pin.
If a wake-up event occurs during the transition between
normal and sleep mode (during the tdisable filtering time), it
will be regarded as a valid wake-up and the chip will enter
standby mode with the appropriate setting of pins RxDx.
LIN Wake−up
Remote (or LIN) wake-up can be recognized on all LINx
pins on NCV7424 when LINx bus is externally driven
dominant for longer than tLIN_wake and a rising edge on LIN
occurs afterwards – see Figure 4. Wake-up events can be
exclusively detected in sleep mode or during the transition
from normal mode to sleep mode. Due to timing tolerances,
valid wake-up events beginning shortly before
normal-to-sleep mode transition can be also sometimes
regarded as valid wake−ups.
LINx
Detection of Remote Wake−Up
VBB
LIN recessive level
tLIN_wake
60% VBB
tto_stb
40% VBB
Sleep Mode
LIN dominant level
Standby Mode
Figure 4. LIN Bus Wake−up Detection
www.onsemi.com
6
t
NCV7424
ELECTRICAL CHARACTERISTICS
Definitions
All voltages are referenced to GND (Pins 10, 14. These
pins are electrically connected inside of the package).
Positive currents flow into the IC.
Table 5. DC CHARACTERISTICS (VBB = 5 V to 27 V; TJ = −40°C to +150°C; RL(LIN−VBB) = 500 W, unless otherwise specified.
Typical values are given at V(VBB) = 12 V and TJ = 25°C, unless otherwise specified.)
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
CURRENT CONSUMPTION
IBB_ON_rec
VBB Consumption
Normal Mode; LIN Recessive
VLINx = VBB
2.3
4.7
mA
IBB_ON_dom
VBB Consumption
Normal Mode; LIN Dominant
TxDx = Low
16.5
28
mA
IBB_STB
VBB Consumption
Standby Mode
VLINx = VBB
0.22
0.45
mA
IBB_SLP
VBB Consumption
Sleep Mode
VLINx = VBB
11
35
mA
IBB_SLP_18V
VBB Consumption
Sleep Mode, VBB < 18 V
VLINx = VBB
10
33
mA
IBB_SLP_12V
VBB Consumption
Sleep Mode, VBB = 12 V, TJ < 85°C
VLINx = VBB
9
30
mA
POR AND VBB MONITOR
PORH_VBB
Power−on Reset
High Level on VBB
VBB Rising
2
3.3
4.5
V
PORL_VBB
Power−on Reset Low
Level on VBB
VBB Falling
1.7
2.9
4
V
MONH_VBB
Battery Monitoring
High Level
VBB Rising
4.1
4.5
V
MONL_VBB
Battery Monitoring
Low Level
VBB Falling
VLINx_dom_LoSup
LINx Dominant
Output Voltage
TxDx = Low; VBB = 7.3 V
1
1.2
V
VLINx_dom_HiSup
LINx Dominant
Output Voltage
TxDx = Low; VBB = 18 V
1.4
2.0
V
VLINx_REC
LIN Recessive
Output Voltage
TxDx = High; ILIN = 10 mA (Note 6)
VBB
V
ILINx_lim
Short Circuit Current
Limitation
VLINx = VBB = 18 V; TxDx = Low
RLINxslave
Internal Pull−up
Resistance
3
4
V
LIN TRANSMITTERs
VBB − 1.5
70
140
200
mA
20
33
47
kW
0.4
VBB
LIN RECEIVERs
VLINx_bus_dom
Bus Voltage for
Dominant State
VLINx_bus_rec
Bus Voltage for
Recessive State
VLINx_rec_dom
Receiver Threshold
LIN Bus Recessive − Dominant
0.4
0.45
0.6
VBB
VLINx_rec_rec
Receiver Threshold
LIN Bus Dominant − Recessive
0.4
0.55
0.6
VBB
0.6
VBB
6. The voltage drop in Normal mode between LIN and VBB pin is the sum of the diode drop and the drop at serial pull−up resistor. The drop
at the switch is negligible. See Figure 1.
www.onsemi.com
7
NCV7424
Table 5. DC CHARACTERISTICS (VBB = 5 V to 27 V; TJ = −40°C to +150°C; RL(LIN−VBB) = 500 W, unless otherwise specified.
Typical values are given at V(VBB) = 12 V and TJ = 25°C, unless otherwise specified.)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
LIN RECEIVERs
VLINx_rec_cnt
Receiver Centre
Voltage
(VLINx_rec_dom +
VLINx_rec_rec) / 2
0.475
0.5
0.525
VBB
VLINx_rec_hys
Receiver Hysteresis
(VLINx_rec_rec − VLINx_rec_dom)
0.05
0.1
0.175
VBB
ILINx_off_dom
LIN Output Current,
Bus externally driven
to dominant state
Normal Mode, Driver Off;
VBB = 12 V; TxDx = High;
VLINx = 0 V
−1
−0.37
−0.2
mA
ILINx_off_dom_slp
LIN Output Current,
Bus externally driven
to dominant state
Sleep Mode, Driver Off;
VBB = 12 V; TxDx = High;
VLINx = 0 V
−20
−8
−2
mA
ILINx_off_rec
LIN Output Current,
Bus in Recessive
State
Driver Off;
VBB < 18 V; VBB < VLINx < 18 V
2
mA
ILINx_no_GND
Communication not
Affected
VBB = GND = 12 V; 0 < VLINx < 18 V
1
mA
ILINx_no_VBB
LIN Bus Remains
Operational
VBB = GND = 0 V; 0 < VLINx < 18 V
0
5
mA
CLINx
Capacitance on LINx
pin
Not tested in production,
guaranteed by design
20
30
pF
−1
PIN EN
Vil_EN
Low Level Input
Voltage
−0.3
0.8
V
Vih_EN
High Level Input
Voltage
2.0
5.5
V
Rpd_EN
Pull−down
Resistance to Ground
150
350
650
kW
PIN RxDx
Iol_RxDx
Low Level Output
Current
VRxD = 0.4 V, Normal Mode,
VLINx = 0 V
1.5
4.3
Ioh_RxDx
High Level Output
Current
VRxD = 5 V, Normal Mode,
VLINx = VBB
−5
0
mA
5
mA
PIN TxDx
Vil_TxDx
Low Level Input
Voltage
−0.3
0.8
V
Vih_TxDx
High Level Input
Voltage
2.0
5.5
V
Rpd_TxDx
Pull−up on TxDx Pins
60
100
150
kW
150
165
185
°C
THERMAL SHUTDOWN
TJSD
Thermal Shutdown
Junction Temperature
TJSD_HYST
Thermal Shutdown
Hysteresis
Temperature Rising
5
°C
6. The voltage drop in Normal mode between LIN and VBB pin is the sum of the diode drop and the drop at serial pull−up resistor. The drop
at the switch is negligible. See Figure 1.
www.onsemi.com
8
NCV7424
Table 6. AC CHARACTERISTICS (VBB = 5 V to 27 V; TJ = −40°C to +150°C; RL(LIN−VBB) = 500 W, unless otherwise specified.
For the transmitter parameters, the following bus loads are considered: L1 = 1 kW / 1 nF; L2 = 660 W / 6.8 nF; L3 = 500 W / 10 nF
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
LIN TRANSMITTER
D1
Duty Cycle 1 =
tBUS_REC(min) /
(2 x tBIT)
THREC(max) = 0.744 x VBB
THDOM(max) = 0.581 x VBB
tBIT = 50 ms
V(VBB) = 7 V to 18 V
0.396
0.5
D2
Duty Cycle 2 =
tBUS_REC(max) /
(2 x tBIT)
THREC(min) = 0.422 x VBB
THDOM(min) = 0.284 x VBB
tBIT = 50 ms
V(VBB) = 7.6 V to 18 V
0.5
0.581
D3
Duty Cycle 3 =
tBUS_REC(min) /
(2 x tBIT)
THREC(max) = 0.778 x VBB
THDOM(max) = 0.616 x VBB
tBIT = 96 ms
V(VBB) = 7 V to 18 V
0.417
0.5
D4
Duty Cycle 4 =
tBUS_REC(max) /
(2 x tBIT)
THREC(min) = 0.389 x VBB
THDOM(min) = 0.251 x VBB
tBIT = 96 ms
V(VBB) = 7.6 V to 18 V
0.5
0.590
D1e
Duty Cycle 1 =
tBUS_REC(min) /
(2 x tBIT)
THREC(max) = 0.744 x VBB
THDOM(max) = 0.581 x VBB
tBIT = 50 ms
V(VBB) = 5 V to 40 V, (Notes 7 and 8)
0.39
0.5
D2e
Duty Cycle 2 =
tBUS_REC(max) /
(2 x tBIT)
THREC(min) = 0.422 x VBB
THDOM(min) = 0.284 x VBB
tBIT = 50 ms
V(VBB) = 5 V to 40 V, (Notes 7 and 8)
0.5
0.59
D3e
Duty Cycle 3 =
tBUS_REC(min) /
(2 x tBIT)
THREC(max) = 0.778 x VBB
THDOM(max) = 0.616 x VBB
tBIT = 96 ms
V(VBB) = 5 V to 40 V, (Notes 7 and 8)
0.41
0.5
D4e
Duty Cycle 4 =
tBUS_REC(max) /
(2 x tBIT)
THREC(min) = 0.389 x VBB
THDOM(min) = 0.251 x VBB
tBIT = 96 ms
V(VBB) = 5 V to 40 V, (Notes 7 and 8)
0.5
0.6
ttx_prop_down_x
Propagation Delay of
TxDx to LINx. TxD
High to Low
1.3
4.2
10
ms
ttx_prop_up_x
Propagation Delay of
TxDx to LINx. TxD Low
to High
1.3
4.6
10
ms
ttx_sym_x
Propagation Delay
Symmetry
ttrx_prop_down_x − ttrx_prop_up_x
−2.5
−0.4
2.5
ms
tfall
LINx Falling Edge
Normal Mode; VBB = 12 V
9
22.5
ms
trise
LINx Rising Edge
Normal Mode; VBB = 12 V
tsym
LINx Slope Symmetry
Normal Mode; VBB = 12 V
10
22.5
ms
−4
0
4
ms
LIN RECEIVERs
trec_prop_down_x
Propagation Delay of
LINx to RxDx Receiver
Falling Edge
0.1
1.6
6
ms
trec_prop_up_x
Propagation Delay of
LINx to RxDx Receiver
Rising Edge
0.1
1.35
6
ms
trec_sym_x
Propagation Delay
Symmetry
−2
0.25
2
ms
trec_prop_down_x − trec_prop_up_x
7. The external pull-up resistor for duty cycles on V(VBB) = 40 V is 1 kW
8. Not tested in production Extended battery range (5 V; 40 V) is tested on limited sample base only
www.onsemi.com
9
NCV7424
Table 6. AC CHARACTERISTICS (VBB = 5 V to 27 V; TJ = −40°C to +150°C; RL(LIN−VBB) = 500 W, unless otherwise specified.
For the transmitter parameters, the following bus loads are considered: L1 = 1 kW / 1 nF; L2 = 660 W / 6.8 nF; L3 = 500 W / 10 nF
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
MODE TRANSITIONS AND TIMEOUTS
tLINx_wake
Duration of LINx
Dominant for Detection
of Wake−up via LINx
bus
Sleep Mode
30
90
150
ms
tto_stb
Delay from LIN Bus
Dominant to Recessive
Edge to Entering of
Standby Mode after
Valid LIN Wake−up
See Figure 4
2
2.8
18.5
ms
tenable
Duration of High Level
on EN Pin for Tran−
sition to Normal Mode
2
18
47
ms
tdisable
Duration of Low Level
on EN Pin for Tran−
sition to Sleep Mode
2
7.5
18.5
ms
tTxD_timeout
TxD Dominant Timeout
15
28
50
ms
Normal Mode, TxD = Low, Guaran−
tees Baudrate as Low as 1 kbps
7. The external pull-up resistor for duty cycles on V(VBB) = 40 V is 1 kW
8. Not tested in production Extended battery range (5 V; 40 V) is tested on limited sample base only
TxDx
t BIT
t BIT
50%
t
LINx
tBUS_dom(max)
tBUS_rec(min)
THREC(max)
THDOM(max)
Thresholds of
receiving node 1
THREC(min)
THDOM(min)
Thresholds of
receiving node 2
t
tBUS_dom(min)
tBUS_rec(max)
Figure 5. LINx Bus Transmitter Duty Cycle
www.onsemi.com
10
NCV7424
LINx
100%
60%
60%
40%
40%
0%
t
tfall
trise
Figure 6. LINx Bus Transmitter Rising and Falling Times
LINx
VBB
60% VBB
40% VBB
t
RxDx
trec_prop_down
trec_prop_up
50%
t
Figure 7. LINx Bus Receiver Timing
TxDx
tBIT
tBIT
50%
t
LINx
VBB
60% VBB
40% VBB
ttx_prop_down
t
ttx_prop_up
Figure 8. LINx Transmitter Timing
ORDERING INFORMATION
Part Number
NCV7424DB0R2G
Description
Temperature Range
Package
Shipping†
Quad LIN
Transceiver
−40°C to +125°C
TSSOP−16
(Pb−Free)
2500 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
11
NCV7424
PACKAGE DIMENSIONS
TSSOP−16
CASE 948F
ISSUE B
16X K REF
0.10 (0.004)
0.15 (0.006) T U
T U
M
S
V
S
S
K
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K1
2X
L/2
16
9
J1
B
−U−
L
SECTION N−N
J
PIN 1
IDENT.
N
0.25 (0.010)
8
1
M
0.15 (0.006) T U
S
A
−V−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH. PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
N
F
DETAIL E
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
H
D
DETAIL E
G
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
−−−
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.193 0.200
0.169 0.177
−−− 0.047
0.002 0.006
0.020 0.030
0.026 BSC
0.007
0.011
0.004 0.008
0.004 0.006
0.007 0.012
0.007 0.010
0.252 BSC
0_
8_
SOLDERING FOOTPRINT
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
12
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCV7424/D