MC74HC160A D

MC74HC160A
Presettable Counters
High−Performance Silicon−Gate CMOS
The MC74HC160A is identical in pinout to the LS160. The device
inputs are compatible with standard CMOS outputs; with pullup
resistors, they are compatible with LSTTL outputs.
The HC160A is a programmable BCD counters with asynchronous
Reset input.
http://onsemi.com
16
Features
•
•
•
•
•
•
•
•
Output Drive Capability: 10 LSTTL Loads
Outputs Directly Interface to CMOS, NMOS, and TTL
Operating Voltage Range: 2 to 6 V
Low Input Current: 1 mA
High Noise Immunity Characteristic of CMOS Devices
In Compliance with the Requirements Defined by JEDEC Standard
No. 7A
Chip Complexity: 234 FETs or 58.5 Equivalent Gates
These are Pb−Free Devices
P0
PRESENT
DATA
INPUTS
P1
P2
P3
CLOCK
COUNT
ENABLES
3
14
4
13
5
12
6
11
2
15
Q0
Q1
Q2
MARKING
DIAGRAMS
SOIC−16
D SUFFIX
CASE 751B
16
1
HC160AG
AWLYWW
1
16
TSSOP−16
DT SUFFIX
CASE 948F
16
1
HC
160A
ALYWG
G
1
A
= Assembly Location
WL, L
= Wafer Lot
YY, Y
= Year
WW, W = Work Week
G or G
= Pb−Free Package
(Note: Microdot may be in either location)
BCD
OUTPUTS
PIN ASSIGNMENT
Q3
RIPPLE
CARRY
OUT
RESET
1
16
CLOCK
2
15
P0
3
14
VCC
RIPPLE
CARRY OUT
Q0
P1
4
13
Q1
P2
5
12
Q2
RESET
P3
6
11
Q3
LOAD
ENABLE P
7
10
ENABLE T
ENABLE P
GND
8
9
PIN 16 = VCC
PIN 8 = GND
ENABLE T
ORDERING INFORMATION
Figure 1. Logic Diagram
Device
Count Mode
Reset Mode
HC160
BCD
Asynchronous
© Semiconductor Components Industries, LLC, 2013
May, 2013 − Rev. 2
LOAD
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
1
Publication Order Number:
MC74HC160A/D
MC74HC160A
FUNCTION TABLE
Inputs
Clock
Outputs
Reset*
Load
Enable P
Enable T
Q
L
X
X
X
Reset
H
L
X
X
Load Preset Data
H
H
H
H
Count
H
H
L
X
No Count
H
H
X
L
No Count
*HC160 is an Asynchronous Reset Device.
H = High Level
L = Low Level
X = Don’t Care
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
−0.5 to +7.0
V
V
VCC
DC Supply Voltage (Referenced to GND)
Vin
DC Input Voltage (Referenced to GND)
−0.5 to VCC + 0.5
Vout
DC Output Voltage (Referenced to GND)
−0.5 to VCC + 0.5
V
Iin
DC Input Current, per Pin
±20
mA
Iout
DC Output Current, per Pin
±25
mA
ICC
DC Supply Current, VCC and GND Pins
±50
mA
PD
Power Dissipation in Still Air, Plastic or Ceramic DIP†
SOIC Package†
750
500
mW
Tstg
Storage Temperature
−65 to +150
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress
ratings only. Functional operation above the Recommended Operating Conditions is not implied.
Extended exposure to stresses above the Recommended Operating Conditions may affect device
reliability.
†Derating − SOIC Package: − 7 mW/°C from 65° to 125°C
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Vin, Vout
Parameter
DC Supply Voltage (Referenced to GND)
DC Input Voltage, Output Voltage (Referenced to GND)
TA
Operating Temperature, All Package Types
tr, tf
Input Rise and Fall Time
(Figure 3)
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
Min
Max
Unit
2.0
6.0
V
0
VCC
V
−55
+125
°C
0
0
0
1000
500
400
ns
http://onsemi.com
2
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND v (Vin or Vout) v VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
MC74HC160A
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
Guaranteed Limit
Symbol
Parameter
Test Conditions
VCC
V
− 55 to
25°C
v 85°C
v 125°C
Unit
VIH
Minimum High−Level Input
Voltage
Vout = 0.1 V or VCC − 0.1 V
|Iout| v 20 mA
2.0
3.0
4.5
6.0
1.5
2.1
3.15
4.2
1.5
2.1
3.15
4.2
1.5
2.1
3.15
4.2
V
VIL
Maximum Low−Level Input
Voltage
Vout = 0.1 V or VCC − 0.1 V
|Iout| v 20 mA
2.0
3.0
4.5
6.0
0.5
0.9
1.35
1.8
0.5
0.9
1.35
1.8
0.5
0.9
1.35
1.8
V
VOH
Minimum High−Level Output
Voltage
Vin = VIH or VIL
|Iout| v 20 mA
2.0
4.5
6.0
1.9
4.4
5.9
1.9
4.4
5.9
1.9
4.4
5.9
V
3.0
4.5
6.0
2.48
3.98
5.48
2.34
3.84
5.34
2.20
3.70
5.20
2.0
4.5
6.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
3.0
4.5
6.0
0.26
0.26
0.26
0.33
0.33
0.33
0.40
0.40
0.40
Vin = VIH or VIL
VOL
Maximum Low−Level Output
Voltage
|Iout| v 2.4 m
|Iout| v 4.0 mA
|Iout| v 5.2 mA
Vin = VIH or VIL
|Iout| v 20 mA
Vin = VIH or VIL
|Iout| v 2.4 m
|Iout| v 4.0 mA
|Iout| v 5.2 mA
V
Iin
Maximum Input Leakage Current
Vin = VCC or GND
6.0
± 0.1
± 1.0
± 1.0
mA
ICC
Maximum Quiescent Supply
Current (per Package)
Vin = VCC or GND
Iout = 0 mA
6.0
4
40
160
mA
http://onsemi.com
3
MC74HC160A
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
Guaranteed Limit
Parameter
Symbol
VCC
V
− 55 to
25°C
v 85°C
v 125°C
Unit
fmax
Maximum Clock Frequency (50% Duty Cycle)*
(Figures 3 and 8)
2.0
4.5
6.0
6.0
30
35
4.8
24
28
4.0
20
24
MHz
tPLH
Maximum Propagation Delay, Clock to Q
(Figures 3 and 8)
2.0
4.5
6.0
170
34
29
215
43
37
255
51
43
ns
2.0
4.5
6.0
205
41
35
255
51
43
310
62
53
tPHL
tPHL
Maximum Propagation Delay, Reset to Q (HC160A Only)
(Figures 4 and 8)
2.0
4.5
6.0
210
42
36
265
53
45
315
63
54
ns
tPLH
Maximum Propagation Delay, Enable T to Ripple Carry Out
(Figures 5 and 8)
2.0
4.5
6.0
160
32
27
200
40
34
240
48
41
ns
2.0
4.5
6.0
195
39
33
245
49
42
295
59
50
2.0
4.5
6.0
175
35
30
220
44
37
265
53
45
2.0
4.5
6.0
215
43
37
270
54
46
325
65
55
tPHL
tPLH
Maximum Propagation Delay, Clock to Ripple Carry Out
(Figures 3 and 8)
tPHL
ns
tPHL
Maximum Propagation Delay, Reset to Ripple Carry Out
(HC160A Only)
(Figures 4 and 8)
2.0
4.5
6.0
220
44
37
275
55
47
330
66
56
ns
tTLH,
tTHL
Maximum Output Transition Time, Any Output
(Figures 3 and 8)
2.0
4.5
6.0
75
15
13
95
19
16
110
22
19
ns
−
10
10
10
pF
Cin
Maximum Input Capacitance
*Applies to noncascaded/nonsynchronously clocked configurations only. With synchronously cascaded counters, (1) Clock to Ripple Carry Out
propagation delays, (2) Enable T or Enable P to Clock setup times, and (3) Clock to Enable T or Enable P hold times determine fmax. However,
if Ripple Carry Out of each stage is tied to the Clock of the next stage (nonsynchronously clocked), the fmax in the table above is applicable.
See Applications Information in this data sheet.
Typical @ 25°C, VCC = 5.0 V
CPD
60
Power Dissipation Capacitance (Per Package)*
*Used to determine the no−load dynamic power consumption: PD = CPD VCC
2f
+ ICC VCC .
http://onsemi.com
4
pF
MC74HC160A
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
TIMING REQUIREMENTS (Input tr = tf = 6 ns)
Guaranteed Limit
Symbol
Parameter
VCC
V
− 55 to
25°C
v 85°C
v 125°C
Unit
tsu
Minimum Setup Time, Preset Data Inputs to Clock
(Figure 6)
2.0
4.5
6.0
150
30
26
190
38
33
225
45
38
ns
tsu
Minimum Setup Time, Load to Clock
(Figure 6)
2.0
4.5
6.0
135
27
23
170
34
29
205
41
35
ns
tsu
Minimum Setup Time, Enable T or Enable P to Clock
(Figure 7)
2.0
4.5
6.0
200
40
34
250
50
43
300
60
51
ns
th
Minimum Hold Time, Clock to Preset Data Inputs
(Figure 6)
2.0
4.5
6.0
50
10
9
65
13
11
75
15
13
ns
th
Minimum Hold Time, Clock to Load
(Figure 6)
2.0
4.5
6.0
3
3
3
3
3
3
3
3
3
ns
th
Minimum Hold Time, Clock to Enable T or Enable P
(Figure 7)
2.0
4.5
6.0
3
3
3
3
3
3
3
3
3
ns
trec
Minimum Recovery Time, Reset Inactive to Clock
(Figure 4)
2.0
4.5
6.0
125
25
21
155
31
26
190
38
32
ns
trec
Minimum Recovery Time, Load Inactive to Clock
(Figure 6)
2.0
4.5
6.0
125
25
21
155
31
26
190
38
32
ns
tw
Minimum Pulse Width, Clock
(Figure 3)
2.0
4.5
6.0
80
16
14
100
20
17
120
24
20
ns
tw
Minimum Pulse Width, Reset
(Figure 4)
2.0
4.5
6.0
80
16
14
100
20
17
120
24
20
ns
Maximum Input Rise and Fall Times
(Figure 3)
2.0
4.5
6.0
1000
500
400
1000
500
400
1000
500
400
ns
tr, tf
http://onsemi.com
5
MC74HC160A
FUNCTION DESCRIPTION
Loading
The HC160A is a programmable 4−bit synchronous
counters that feature parallel Load, synchronous or
asynchronous Reset, a Carry Output for cascading, and
count−enable controls. The HC160A is a BCD counter with
asynchronous Reset.
With the rising edge of the Clock, a low level on Load (pin
9) loads the data from the Preset Data Input pins (P0, P1, P2,
P3) into the internal flip−flops and onto the output pins, Q0
through Q3. The count function is disabled as long as Load
is low.
Although the HC160A is a BCD counters, they may be
programmed to any state. If they are loaded with a state
disallowed in BCD code, they will return to their normal
count sequence within two clock pulses (see the Output State
Diagram).
INPUTS
Clock (Pin 2)
The internal flip−flops toggle and the output count
advances with the rising edge of the Clock input. In addition,
control functions, such as loading occur with the rising edge
of the Clock input.
Count Enable/Disable
Preset Data Inputs P0, P1, P2, P3 (Pins 3, 4, 5, 6)
These devices have two count−enable control pins:
Enable P (pin 7) and Enable T (pin 10). The devices count
when these two pins and the Load pin are high. The logic
equation is:
Count Enable = Enable P Enable T Load
The count is either enabled or disabled by the control
inputs according to Table 1. In general, Enable P is a
count−enable control; Enable T is both a count−enable and
a Ripple−Carry Output control.
These are the data inputs for programmable counting.
Data on these pins may be synchronously loaded into the
internal flip−flops and appear at the counter outputs. P0 (pin
3) is the least−significant bit and P3 (pin 6) is the
most−significant bit.
OUTPUTS
Q0, Q1, Q2, Q3 (Pins 14, 13, 12, 11)
These are the counter outputs (BCD or binary). Q0 (pin
14) is the least−significant bit and Q3 (pin 11) is the
most−significant bit.
Table 1. COUNT ENABLE/DISABLE
Control Inputs
Ripple Carry Out (Pin 15)
When the counter is in its maximum state (1001 for the
BCD counters or 1111 for the binary counters), this output
goes high, providing an external look−ahead carry pulse that
may be used to enable successive cascaded counters. Ripple
Carry Out remains high only during the maximum count
state. The logic equation for this output is:
Ripple Carry Out =
Enable T Q0 Q1 Q2 Q3
for BCD counters
Result at Outputs
Load
Enable P
Enable T
Q0 − Q3
Ripple Carry Out
H
H
H
Count
L
H
H
No Count
High when
Q0 −Q3 are maximum*
X
L
H
No Count
High when
Q0 −Q3 are maximum*
X
X
L
No Count
L
*Q0 through Q3 are maximum for the HC160A when Q3 Q2 Q1 Q0
= 1001.
CONTROL FUNCTIONS
Resetting
A low level on the Reset pin (pin 1) resets the internal
flip−flops and sets the outputs (Q0 through Q3) to a low
level. The HC160A resets asynchronously.
0
1
2
3
4
15
5
14
6
13
7
12
11
10
9
8
Figure 2. Output State Diagrams HC160A BCD Counters
http://onsemi.com
6
MC74HC160A
SWITCHING WAVEFORMS
tr
tw
tf
VCC
90%
50%
10%
CLOCK
VCC
50%
RESET
GND
GND
tPHL
tw
1/fmax
tPHL
tPLH
ANY
OUTPUT
50%
ANY
OUTPUT
90%
50%
10%
trec
VCC
tTHL
tTLH
50%
CLOCK
GND
Figure 3.
Figure 4.
tr
tf
ENABLE T
RIPPLE
CARRY
OUT
VALID
VCC
90%
50%
10%
tPLH
90%
50%
10%
GND
tPHL
INPUTS
P0, P1,
P2, P3
VCC
50%
GND
tsu
tTLH
th
VCC
tTHL
LOAD
50%
GND
Figure 5.
tsu
trec
th
VCC
CLOCK
50%
GND
Figure 6.
TEST CIRCUIT
VALID
ENABLE T
OR
ENABLE P
TEST POINT
VCC
50%
OUTPUT
GND
tsu
DEVICE
UNDER
TEST
th
VCC
CLOCK
CL*
50%
GND
Figure 7.
*Includes all probe and jig capacitance
Figure 8.
http://onsemi.com
7
3
http://onsemi.com
8
LOAD
CLOCK
RESET
ENABLE T
ENABLE P
P3
P2
3
2
1
10
7
6
5
P1 4
P0
LOAD
LOAD
C
C
R
Q3
Q3
Q2
Q2
Q1
Q1
Q0
Q0
VCC = PIN 16
GND = PIN 8
Q3
Q2
Q1
Q0
15 RIPPLE
CARRY
OUT
11
12
13
14
The flip−flops shown in the circuit diagrams are Toggle−Enable flip−flops. A Toggle−
Enable flip−flop is a combination of a D flip−flop and a T flip−flop. When loading data from
Preset inputs P0, P1, P2, and P3, the Load signal is used to disable the Toggle input (Tn) of
the flip−flop. The logic level at the Pn input is then clocked to the Q output of the flip−flop
on the next rising edge of the clock.
A logic zero on the Reset device input forces the internal clock (C) high and resets the Q
output of the flip−flop low.
T3
R
C
C
LOAD
LOAD
P3
T2
R
C
C
LOAD
LOAD
P2
T1
R
C
C
LOAD
LOAD
P1
T0
R
C
C
LOAD
LOAD
P0
MC74HC160A
BCD Counter with Asynchronous Reset
MC74HC160A
MC74HC160A
Sequence illustrated in waveforms:
1. Reset outputs to zero.
2. Preset to BCD seven.
3. Count to eight, nine, zero, one, two, and three.
4. Inhibit.
RESET (HC160A)
(ASYNCHRONOUS)
LOAD
P0
PRESET
DATA
INPUTS
P1
P2
P3
CLOCK
(HC160A)
CLOCK
(HC162A)
COUNT
ENABLES
ENABLE P
ENABLE T
Q0
Q1
OUTPUTS
Q2
Q3
RIPPLE
CARRY
OUT
7
8
9
0
1
2
3
COUNT
RESET
LOAD
Figure 9. MC74HC160A Timing Diagram
http://onsemi.com
9
INHIBIT
MC74HC160A
TYPICAL APPLICATIONS CASCADING
LOAD
INPUTS
INPUTS
LOAD
H = COUNT
L = DISABLE
H = COUNT
L = DISABLE
P0 P1 P2 P3
ENABLE P
LOAD
P0 P1 P2 P3
ENABLE T
LOAD
P0 P1 P2 P3
ENABLE P
ENABLE P
RIPPLE
CARRY
OUT
INPUTS
RIPPLE
CARRY
OUT
ENABLE T
CLOCK
CLOCK
CLOCK
R
R
R
Q0 Q1 Q2 Q3
Q0 Q1 Q2 Q3
RIPPLE
CARRY
OUT
ENABLE T
TO
MORE
SIGNIFICANT
STAGES
Q0 Q1 Q2 Q3
RESET
OUTPUTS
OUTPUTS
OUTPUTS
CLOCK
NOTE:
When used in these cascaded configurations the clock fmax guaranteed limits may not apply. Actual performance will depend
on number of stages. This limitation is due to set up times between Enable (Port) and Clock.
Figure 10. N−Bit Synchronous Counters
INPUTS
INPUTS
INPUTS
LOAD
ENABLE P
ENABLE T
LOAD
P0 P1 P2 P3
ENABLE P
P0 P1 P2 P3
ENABLE P
RIPPLE
CARRY
OUT
ENABLE T
CLOCK
LOAD
ENABLE T
LOAD
P0 P1 P2 P3
ENABLE P
RIPPLE
CARRY
OUT
ENABLE T
CLOCK
CLOCK
CLOCK
R
R
R
Q0 Q1 Q2 Q3
Q0 Q1 Q2 Q3
RIPPLE
CARRY
OUT
TO
MORE
SIGNIFICANT
STAGES
Q0 Q1 Q2 Q3
RESET
OUTPUTS
OUTPUTS
OUTPUTS
Figure 11. Nibble Ripple Counter
ORDERING INFORMATION
Package
Shipping†
MC74HC160ADG
SOIC−16
(Pb−Free)
48 Units / Rail
MC74HC160ADR2G
SOIC−16
(Pb−Free)
2500 Tape & Reel
Device
MC74HC160ADTG
TSSOP−16*
96 Units / Rail
MC74HC160ADTR2G
TSSOP−16*
2500 Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently Pb−Free.
http://onsemi.com
10
MC74HC160A
PACKAGE DIMENSIONS
TSSOP−16
DT SUFFIX
CASE 948F−01
ISSUE B
16X K REF
0.10 (0.004)
0.15 (0.006) T U
T U
M
S
V
S
K
S
K1
2X
L/2
16
9
B
−U−
L
SECTION N−N
J
PIN 1
IDENT.
N
8
1
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
J1
0.25 (0.010)
M
0.15 (0.006) T U
S
A
−V−
N
F
DETAIL E
C
0.10 (0.004)
−T− SEATING
PLANE
D
H
G
DETAIL E
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH. PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
MILLIMETERS
INCHES
DIM MIN
MAX
MIN
MAX
A
4.90
5.10 0.193 0.200
B
4.30
4.50 0.169 0.177
C
−−−
1.20
−−− 0.047
D
0.05
0.15 0.002 0.006
F
0.50
0.75 0.020 0.030
G
0.65 BSC
0.026 BSC
H
0.18
0.28 0.007
0.011
−W−
J
0.09
0.20 0.004 0.008
J1
0.09
0.16 0.004 0.006
K
0.19
0.30 0.007 0.012
K1
0.19
0.25 0.007 0.010
L
6.40 BSC
0.252 BSC
M
0_
8_
0_
8_
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
11
MC74HC160A
PACKAGE DIMENSIONS
SOIC−16
CASE 751B−05
ISSUE K
−A−
16
9
1
8
−B−
P
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
8 PL
0.25 (0.010)
B
M
S
DIM
A
B
C
D
F
G
J
K
M
P
R
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT*
8X
6.40
16X
1.12
1
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
12
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC74HC160A/D