MC74AC373 D

MC74AC373, MC74ACT373
Octal Transparent Latch
with 3-State Outputs
The MC74AC373/74ACT373 consists of eight latches with 3−state
outputs for bus organized system applications. The flip−flops appear
transparent to the data when Latch Enable (LE) is HIGH. When LE is
LOW, the data that meets the setup time is latched. Data appears on the
bus when the Output Enable (OE) is LOW. When OE is HIGH, the bus
output is in the high impedance state.
www.onsemi.com
SOIC−20W
DW SUFFIX
CASE 751D
Features
•
•
•
•
•
Eight Latches in a Single Package
3−State Outputs for Bus Interfacing
Outputs Source/Sink 24 mA
′ACT373 Has TTL Compatible Inputs
These are Pb−Free Devices
1
TSSOP−20
DT SUFFIX
CASE 948E
VCC
O7
D7
D6
O6
O5
D5
D4
O4
LE
20
19
18
17
16
15
14
13
12
11
1
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 8 of this data sheet.
1
2
3
4
5
6
7
8
9
10
OE
O0
D0
D1
O1
O2
D2
D3
O3
GND
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 9 of this data sheet.
Figure 1. Pinout: 20−Lead Packages Conductors
(Top View)
PIN ASSIGNMENT
PIN
FUNCTION
D0−D7
Data Inputs
LE
Latch Enable Input
OE
Output Enable Input
O0−O7
3−State Latch Outputs
D0 D1 D2 D3 D4 D5 D6 D7
LE
OE
O0 O1 O2 O3 O4 O5 O6 O7
Figure 2. Logic Symbol
© Semiconductor Components Industries, LLC, 2015
February, 2015 − Rev. 9
1
Publication Order Number:
MC74AC373/D
MC74AC373, MC74ACT373
FUNCTIONAL DESCRIPTION
The MC74AC373/74ACT373 contains eight D−type
latches with 3−state standard outputs. When the Latch
Enable (LE) input is HIGH, data on the Dn inputs enters the
latches. In this condition the latches are transparent, i.e., a
latch output will change state each time its D input changes.
When LE is LOW, the latches store the information that was
present on the D inputs a setup time preceding the
HIGH−to−LOW transition of LE. The 3-state standard
outputs are controlled by the Output Enable (OE) input.
When OE is LOW, the standard outputs are in the 2−state
mode. When OE is HIGH, the standard outputs are in the
high impedance mode but this does not interfere with
entering new data into the latches.
TRUTH TABLE
Inputs
Outputs
OE
LE
Dn
On
H
L
L
L
X
H
H
L
X
L
H
X
Z
L
H
O0
H = HIGH Voltage Level
L = LOW Voltage Level
Z = High Impedance
X = Immaterial
O0 = Previous O0 before LOW-to-HIGH Transition of Clock
D0
D1
D
D2
D
G
O
D3
D
G
O
D4
D
G
O
D5
D
G
O
D6
D
G
O
D7
D
G
O
D
G
LE
OE
NOTE:
This diagram is provided only for the understanding of logic operations and
should not be used to estimate propagation delays.
Figure 3. Logic Diagram
www.onsemi.com
2
O
G
O
MC74AC373, MC74ACT373
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
−0.5 to +7.0
V
VCC
DC Supply Voltage (Referenced to GND)
VIN
DC Input Voltage (Referenced to GND)
−0.5 to VCC +0.5
V
DC Output Voltage (Referenced to GND) (Note 1)
−0.5 to VCC +0.5
V
VOUT
IIK
DC Input Diode Current
±20
mA
IOK
DC Output Diode Current
±50
mA
IOUT
DC Output Sink/Source Current
±50
mA
ICC
DC Supply Current, per Output Pin
±50
mA
IGND
DC Ground Current, per Output Pin
±100
mA
TSTG
Storage Temperature Range
*65 to )150
_C
TL
Lead temperature, 1 mm from Case for 10 Seconds
260
_C
TJ
Junction Temperature Under Bias
140
_C
qJA
Thermal Resistance (Note 2)
65.8
110.7
_C/W
MSL
Moisture Sensitivity
FR
Flammability Rating
VESD
ILatchup
SOIC
TSSOP
Level 1
Oxygen Index: 30% − 35%
ESD Withstand Voltage
Latchup Performance
UL 94 V−0 @ 0.125 in
Human Body Model (Note 3)
Machine Model (Note 4)
Charged Device Model (Note 5)
Above VCC and Below GND at 85_C (Note 6)
> 2000
> 200
> 1000
V
±100
mA
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. IOUT absolute maximum rating must be observed.
2. The package thermal impedance is calculated in accordance with JESD 51−7.
3. Tested to EIA/JESD22−A114−A.
4. Tested to EIA/JESD22−A115−A.
5. Tested to JESD22−C101−A.
6. Tested to EIA/JESD78.
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
VIN, VOUT
tr, tf
Parameter
Supply Voltage
Min
Typ
Max
′AC
2.0
5.0
6.0
′ACT
4.5
5.0
5.5
0
−
VCC
VCC @ 3.0 V
−
150
−
VCC @ 4.5 V
−
40
−
VCC @ 5.5 V
−
25
−
VCC @ 4.5 V
−
10
−
VCC @ 5.5 V
−
8.0
−
−40
25
85
°C
DC Input Voltage, Output Voltage (Ref. to GND)
Input Rise and Fall Time (Note 7)
′AC Devices except Schmitt Inputs
Unit
V
V
ns/V
tr, tf
Input Rise and Fall Time (Note 8)
′ACT Devices except Schmitt Inputs
TA
Operating Ambient Temperature Range
IOH
Output Current − High
−
−
−24
mA
IOL
Output Current − Low
−
−
24
mA
ns/V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
7. VIN from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times.
8. VIN from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times.
www.onsemi.com
3
MC74AC373, MC74ACT373
DC CHARACTERISTICS
Symbol
Parameter
VCC
(V)
74AC
74AC
TA = +25°C
TA =
−40°C to +85°C
Typ
VIH
VIL
VOH
VOL
Unit
Conditions
Guaranteed Limits
Minimum High Level
Input Voltage
3.0
4.5
5.5
1.5
2.25
2.75
2.1
3.15
3.85
2.1
3.15
3.85
V
VOUT = 0.1 V
or VCC − 0.1 V
Maximum Low Level
Input Voltage
3.0
4.5
5.5
1.5
2.25
2.75
0.9
1.35
1.65
0.9
1.35
1.65
V
VOUT = 0.1 V
or VCC − 0.1 V
Minimum High Level
Output Voltage
3.0
4.5
5.5
2.99
4.49
5.49
2.9
4.4
5.4
2.9
4.4
5.4
V
3.0
4.5
5.5
−
−
−
2.56
3.86
4.86
2.46
3.76
4.76
3.0
4.5
5.5
0.002
0.001
0.001
0.1
0.1
0.1
0.1
0.1
0.1
3.0
4.5
5.5
−
−
−
0.36
0.36
0.36
0.44
0.44
0.44
Maximum Low Level
Output Voltage
IOUT = −50 mA
V
*VIN = VIL or VIH
−12 mA
IOH
−24 mA
−24 mA
IOUT = 50 mA
V
V
*VIN = VIL or VIH
12 mA
IOL
24 mA
24 mA
IIN
Maximum Input
Leakage Current
5.5
−
±0.1
±1.0
mA
VI = VCC, GND
IOZ
Maximum
3−State
Current
5.5
−
±0.5
±5.0
mA
VI (OE) = VIL, VIH
VI = VCC, GND
VO = VCC, GND
5.5
−
−
75
mA
VOLD = 1.65 V
Max
5.5
−
−
−75
mA
VOHD = 3.85 V Min
5.5
−
8.0
80
mA
VIN = VCC or GND
IOLD
†Minimum Dynamic
Output Current
IOHD
ICC
Maximum Quiescent
Supply Current
*All outputs loaded; thresholds on input associated with output under test.
†Maximum test duration 2.0 ms, one output loaded at a time.
NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC.
www.onsemi.com
4
MC74AC373, MC74ACT373
AC CHARACTERISTICS (For Figures and Waveforms − See AND8277/D at www.onsemi.com)
Symbol
Parameter
VCC*
(V)
74AC
74AC
TA = +25°C
CL = 50 pF
TA = −40°C
to +85°C
CL = 50 pF
Min
Typ
Max
Min
Max
Unit
Fig.
No.
tPLH
Propagation Delay
Dn to On
3.3
5.0
1.5
1.5
10
7.0
13.5
9.5
1.5
1.5
15
10.5
ns
3−5
tPHL
Propagation Delay
Dn to On
3.3
5.0
1.5
1.5
9.5
7.0
13
9.5
1.5
1.5
14.5
10.5
ns
3−5
tPLH
Propagation Delay
LE to On
3.3
5.0
1.5
1.5
10
7.5
13.5
9.5
1.5
1.5
15
10.5
ns
3−6
tPHL
Propagation Delay
LE to On
3.3
5.0
1.5
1.5
9.5
7.0
12.5
9.5
1.5
1.5
14
10.5
ns
3−6
tPZH
Output Enable Time
3.3
5.0
1.5
1.5
9.0
7.0
11.5
8.5
1.0
1.0
13
9.5
ns
3−7
tPZL
Output Enable Time
3.3
5.0
1.5
1.5
8.5
6.5
11.5
8.5
1.0
1.0
13
9.5
ns
3−8
tPHZ
Output Disable Time
3.3
5.0
1.5
1.5
10
8.0
12.5
11
1.0
1.0
14.5
12.5
ns
3−7
tPLZ
Output Disable Time
3.3
5.0
1.5
1.5
8.0
6.5
11.5
8.5
1.0
1.0
12.5
10
ns
3−8
*Voltage Range 3.3 V is 3.3 V ±0.3 V.
Voltage Range 5.0 V is 5.0 V ±0.5 V.
AC OPERATING REQUIREMENTS
Symbol
VCC*
(V)
Parameter
74AC
74AC
TA = +25°C
CL = 50 pF
TA = −40°C
to +85°C
CL = 50 pF
Typ
Unit
Fig.
No.
Guaranteed Minimum
ts
Setup Time, HIGH or LOW
Dn to LE
3.3
5.0
3.5
2.0
5.5
4.0
6.0
4.5
ns
3−9
th
Hold Time, HIGH or LOW
Dn to LE
3.3
5.0
−3.0
−1.5
1.0
1.0
1.0
1.0
ns
3−9
tw
LE Pulse Width, HIGH
3.3
5.0
4.0
2.0
5.5
4.0
6.0
4.5
ns
3−6
*Voltage Range 3.3 V is 3.3 V ±0.3 V.
Voltage Range 5.0 V is 5.0 V ±0.5 V.
www.onsemi.com
5
MC74AC373, MC74ACT373
DC CHARACTERISTICS
Symbol
Parameter
VCC
(V)
74ACT
74ACT
TA = +25°C
TA =
−40°C to +85°C
Typ
Unit
Conditions
Guaranteed Limits
VIH
Minimum High Level
Input Voltage
4.5
5.5
1.5
1.5
2.0
2.0
2.0
2.0
V
VOUT = 0.1 V
or VCC − 0.1 V
VIL
Maximum Low Level
Input Voltage
4.5
5.5
1.5
1.5
0.8
0.8
0.8
0.8
V
VOUT = 0.1 V
or VCC − 0.1 V
VOH
Minimum High Level
Output Voltage
4.5
5.5
4.49
5.49
4.4
5.4
4.4
5.4
V
4.5
5.5
−
−
3.86
4.86
3.76
4.76
4.5
5.5
0.001
0.001
0.1
0.1
0.1
0.1
4.5
5.5
−
−
0.36
0.36
0.44
0.44
V
*VIN = VIL or VIH
24 mA
IOL
24 mA
Maximum Input
Leakage Current
5.5
−
±0.1
±1.0
mA
VI = VCC, GND
Additional Max. ICC/Input
5.5
0.6
−
1.5
mA
VI = VCC − 2.1 V
Maximum
3-State
Current
5.5
−
±0.5
±5.0
mA
VI (OE) = VIL, VIH
VI = VCC, GND
VO = VCC, GND
5.5
−
−
75
mA
VOLD = 1.65 V Max
5.5
−
−
−75
mA
VOHD = 3.85 V Min
5.5
−
8.0
80
mA
VIN = VCC or GND
VOL
IIN
DICCT
IOZ
IOLD
IOHD
ICC
Maximum Low Level
Output Voltage
†Minimum Dynamic
Output Current
Maximum Quiescent
Supply Current
*All outputs loaded; thresholds on input associated with output under test.
†Maximum test duration 2.0 ms, one output loaded at a time.
www.onsemi.com
6
V
V
IOUT = −50 mA
*VIN = VIL or VIH
IOH −24 mA
−24 mA
IOUT = 50 mA
MC74AC373, MC74ACT373
AC CHARACTERISTICS (For Figures and Waveforms − See AND8277/D at www.onsemi.com)
Parameter
Symbol
VCC*
(V)
74ACT
74ACT
TA = +25°C
CL = 50 pF
TA = −40°C
to +85°C
CL = 50 pF
Min
Typ
Max
Min
Max
Unit
Fig.
No.
tPLH
Propagation Delay
Dn to On
5.0
2.5
8.5
10
1.5
11.5
ns
3−5
tPHL
Propagation Delay
Dn to On
5.0
2.0
8.0
10
1.5
11.5
ns
3−5
tPLH
Propagation Delay
LE to On
5.0
2.5
8.5
11
2.0
11.5
ns
3−6
tPHL
Propagation Delay
LE to On
5.0
2.0
8.0
10
1.5
11.5
ns
3−6
tPZH
Output Enable Time
5.0
2.0
8.0
9.5
1.5
10.5
ns
3−7
tPZL
Output Enable Time
5.0
2.0
7.5
9.0
1.5
10.5
ns
3−8
tPHZ
Output Disable Time
5.0
2.5
9.0
11
2.5
12.5
ns
3−7
5.0
1.5
7.5
8.5
1.0
10
ns
3−8
tPLZ
Output Disable Time
*Voltage Range 5.0 V is 5.0 V ±0.5 V.
AC OPERATING REQUIREMENTS (For Figures and Waveforms − See AND8277/D at www.onsemi.com)
Parameter
Symbol
VCC*
(V)
Typ
74ACT
74ACT
TA = +25°C
CL = 50 pF
TA = −40°C
to +85°C
CL = 50 pF
Unit
Fig.
No.
Guaranteed Minimum
ts
Setup Time, HIGH or LOW
Dn to LE
5.0
3.0
7.0
8.0
ns
3−9
th
Hold Time, HIGH or LOW
Dn to LE
5.0
0
0
1.0
ns
3−9
5.0
2.0
7.0
8.0
ns
3−6
tw
LE Pulse Width, HIGH
*Voltage Range 5.0 V is 5.0 V ±0.5 V.
CAPACITANCE
Symbol
Parameter
Value
Typ
Unit
Test Conditions
CIN
Input Capacitance
4.5
pF
VCC = 5.0 V
CPD
Power Dissipation Capacitance
40
pF
VCC = 5.0 V
www.onsemi.com
7
MC74AC373, MC74ACT373
ORDERING INFORMATION
Package
Shipping†
MC74AC373DWG
SOIC−20
(Pb−Free)
38 Units / Rail
MC74AC373DWR2G
SOIC−20
(Pb−Free)
1000 / Tape & Reel
MC74ACT373DWG
SOIC−20
(Pb−Free)
38 Units / Rail
MC74ACT373DWR2G
SOIC−20
(Pb−Free)
1000 / Tape & Reel
MC74AC373DTG
TSSOP−20
(Pb−Free)
75 Units / Rail
MC74AC373DTR2G
TSSOP−20
(Pb−Free)
2500 / Tape & Reel
MC74ACT373DTG
TSSOP−20
(Pb−Free)
75 Units / Rail
MC74ACT373DTR2G
TSSOP−20
(Pb−Free)
2500 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MARKING DIAGRAMS
SOIC−20W
TSSOP−20
20
20
AC
373
ALYWG
G
AC373
AWLYYWWG
1
1
20
20
ACT
373
ALYWG
G
ACT373
AWLYYWWG
1
1
A
= Assembly Location
WL, L
= Wafer Lot
YY, Y
= Year
WW, W = Work Week
G or G
= Pb−Free Package
(Note: Microdot may be in either location)
www.onsemi.com
8
MC74AC373, MC74ACT373
PACKAGE DIMENSIONS
TSSOP−20
DT SUFFIX
CASE 948E−02
ISSUE C
20X
0.15 (0.006) T U
2X
K REF
0.10 (0.004)
S
L/2
20
M
T U
S
V
ÍÍÍÍ
ÍÍÍÍ
ÍÍÍÍ
K
K1
S
J J1
11
B
L
SECTION N−N
−U−
PIN 1
IDENT
0.25 (0.010)
N
1
10
M
0.15 (0.006) T U
S
A
−V−
N
F
DETAIL E
C
G
D
0.100 (0.004)
−T− SEATING
H
DETAIL E
SOLDERING FOOTPRINT*
PLANE
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION:
MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE
MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH OR GATE BURRS
SHALL NOT EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION
SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
MILLIMETERS
INCHES
DIM MIN
MAX
MIN
MAX
A
6.40
6.60 0.252
0.260
B
4.30
4.50 0.169
0.177
C
--1.20
--0.047
D
0.05
0.15 0.002
0.006
F
0.50
0.75 0.020
0.030
G
0.65 BSC
0.026 BSC
−W−
H
0.27
0.37
0.011
0.015
J
0.09
0.20 0.004
0.008
J1
0.09
0.16 0.004
0.006
K
0.19
0.30 0.007
0.012
K1
0.19
0.25 0.007
0.010
L
6.40 BSC
0.252 BSC
M
0_
8_
0_
8_
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
9
MC74AC373, MC74ACT373
PACKAGE DIMENSIONS
SOIC−20W
DW SUFFIX
CASE 751D−05
ISSUE G
20
11
X 45 _
h
H
M
E
0.25
10X
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF B
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
q
A
B
M
D
1
10
20X
B
B
0.25
M
T A
S
B
S
L
A
18X
e
A1
DIM
A
A1
B
C
D
E
e
H
h
L
q
MILLIMETERS
MIN
MAX
2.35
2.65
0.10
0.25
0.35
0.49
0.23
0.32
12.65
12.95
7.40
7.60
1.27 BSC
10.05
10.55
0.25
0.75
0.50
0.90
0_
7_
SEATING
PLANE
C
T
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC74AC373/D