MC33762 D

MC33762
Dual Ultra Low−Noise Low
Dropout Voltage Regulator
with 1.0 V ON/OFF Control
The MC33762 is a dual Low DropOut (LDO) regulator featuring
excellent noise performances. Thanks to its innovative design, the
circuit reaches an impressive 40 mVRMS noise level without an
external bypass capacitor. Housed in a small m8 package, it represents
the ideal designer’s choice when space and noise are at premium.
The absence of external bandgap capacitor accelerates the response
time to a wake−up signal and keeps it within 40 ms, making the
MC33762 as a natural candidate for portable applications.
The MC33762 also hosts a novel architecture which prevents
excessive undershoots in the presence of fast transient bursts, as in any
bursting systems.
Finally, with a static line regulation better than −75 dB, it naturally
shields the downstream electronics from choppy lines.
Features
• Nominal Output Current of 80 mA with a 100 mA Peak Capability
• Ultra−Low Noise: 150 nV/√Hz @ 100 Hz, 40 mVRMS
•
•
8
1
Micro8t
DM SUFFIX
CASE 846A
PIN CONFIGURATION AND
MARKING DIAGRAM
1
GND1
En1
GND2
En2
8
xxxx
AYW G
G
•
•
•
•
•
•
•
•
100 Hz−100 kHz Typical, Iout = 60 mA, Co = 1.0 mF
Fast Response Time from OFF to ON: 40 ms Typical
Ready for 1.0 V Platforms: ON with a 900 mV High Level
Typical Dropout of 90 mV @ 30 mA, 160 mV @ 80 mA
Ripple Rejection: 70 dB @ 1.0 kHz
1.5% Output Precision @ 25°C
Thermal Shutdown
Vout Available at 2.5 V, 2.8 V, and 3.0 V
Separate Dice for Each Regulator Provides Maximum Isolation
Between Regulators
Operating Range from −40 to +85°C
Pb−Free Packages are Available
http://onsemi.com
Vout1
VCC1
Vout2
VCC2
(Top View)
xxxx = Device Code
See Table − Page 4
A
= Assembly Location
Y
= Year
W
= Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
Applications
• Noise Sensitive Circuits: VCOs RF Stages, etc.
• Bursting Systems (TDMA Phones)
• All Battery Operated Devices
© Semiconductor Components Industries, LLC, 2006
June, 2006 − Rev. 6
1
Publication Order Number:
MC33762/D
MC33762
EN1
On/Off
2
7
VCC1
8
Vout
5
VCC2
6
Vout
Thermal
Shutdown
Band Gap
Reference
GND1
EN2
1
*Current Limit
*Antisaturation Protection
*Load Transient Improvement
On/Off
4
Thermal
Shutdown
Band Gap
Reference
GND2
3
*Current Limit
*Antisaturation Protection
*Load Transient Improvement
Figure 1. Simplified Block Diagram
PIN FUNCTION DESCRIPTIONS
Pin #
Pin Name
1
GND1
Function
Description
2
En1
3
GND2
4
En2
Enables the 2nd LDO
A 900 mV level on this pin is sufficient to start this LDO. A 150 mV shuts it down.
5
Vcc2
2nd LDO Vcc pin
This pin brings the power to the 1st LDO and requires adequate decoupling.
6
Vout2
Shuts or wakes−up the IC
This pin requires a 1.0 mF output capacitor to be stable.
7
Vcc1
1st LDO Vcc pin
This pin brings the power to the 1st LDO and requires adequate decoupling.
8
Vout1
Delivers the output voltage
This pin requires a 1.0 mF output capacitor to be stable.
Ground of the 1st LDO
Enables the 1st LDO
A 900 mV level on this pin is sufficient to start this LDO. A 150 mV shuts it down.
Ground of the 2nd LDO
MAXIMUM RATINGS
Value
Rating
Pin #
Symbol
Min
Max
Unit
1
Vin
−
12
V
ESD Capability, HBM Model
All Pins
−
−
1.0
kV
ESD Capability, Machine Model
All Pins
−
−
200
V
Maximum Power Dissipation
NW Suffix, Plastic Package
Thermal Resistance Junction−to−Air
−
PD
−
Internally Limited
W
−
RqJ−A
−
240
°C/W
Operating Ambient Temperature
Maximum Junction Temperature (Note 1)
Maximum Operating Junction Temperature (Note 2)
−
−
−
TA
TJmax
TJ
−
−
−
−40 to +85
150
125
°C
°C
°C
Storage Temperature Range
−
Tstg
−
−60 to +150
°C
Power Supply Voltage
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Internally limited by shutdown.
2. Specifications are guaranteed below this value.
http://onsemi.com
2
MC33762
ELECTRICAL CHARACTERISTICS
(For typical values TA = 25°C, for min/max values TA = −40°C to +85°C, max TJ = 125°C unless otherwise noted)
Characteristics
Pin #
Symbol
Min
Typ
Max
Unit
Input Voltage Range
2−4
VON/OFF
0
−
Vin
V
ON/OFF Input Resistance (all versions)
2−4
RON/OFF
−
250
−
kW
2−4
VON/OFF
−
900
−
−
150
−
mV
Current Consumption in OFF State (all versions)
OFF Mode Current: Vin = Vout + 1.0 V, IO = 0, VOFF = 150 mV
−
IQOFF
−
0.1
2.0
mA
Current Consumption in ON State (all versions)
ON Mode Current: Vin = Vout + 1.0 V, IO = 0, VON = 3.5 V
−
IQON
−
180
−
mA
Current Consumption in ON State (all versions), ON Mode
Saturation Current: Vin = Vout − 0.5 V, No Output Load
−
IQSAT
−
800
−
mA
Current Limit Vin = Voutnom + 1.0 V,
Output is brought to Voutnom − 0.3 V (all versions)
−
IMAX
100
180
−
mA
LOGIC CONTROL SPECIFICATIONS
ON/OFF Control Voltages (Note 3)
Logic Zero, OFF State, IO = 50 mA
Logic One, ON State, IO = 50 mA
CURRENTS PARAMETERS
OUTPUT VOLTAGES
Vout + 1.0 V < Vin < 6.0 V, TA = 25°C, 1.0 mA < Iout < 80 mA
2.5 V
5−7
Vout
2.462
2.5
2.537
V
2.8 V
5−7
Vout
2.758
2.8
2.842
V
3.0 V
5−7
Vout
2.955
3.0
3.045
V
3.3 V
5−7
Vout
3.250
3.3
3.349
V
3.6 V
5−7
Vout
3.546
3.6
3.654
V
5−7
Vout
−1.5
X
+1.5
%
2.5 V
5−7
Vout
2.425
2.5
2.575
V
2.8 V
5−7
Vout
2.716
2.8
2.884
V
3.0 V
5−7
Vout
2.91
3.0
3.090
V
3.3 V
5−7
Vout
3.201
3.3
3.399
V
3.6 V
5−7
Vout
3.492
3.6
3.708
V
5−7
Vout
−3.0
X
+3.0
%
Vout + 1.0 V < Vin < 12 V, Iout = 80 mA
5−7
Regline
−
−
20
mV
Load Regulation (all versions)Vin = Vout + 1.0 V, Cout = 1.0 mF, Iout = 1.0 to 80 mA
5−7
Regload
−
−
40
mV
Dropout Voltage (all versions) (Note 3)
5−7
5−7
5−7
Vin−Vout
Vin−Vout
Vin−Vout
−
−
−
90
140
160
150
200
250
mV
Ripple Rejection (all versions)
Vin = Vout + 1.0 V + 1.0 kHz 100 mVpp Sinusoidal Signal
5−7
Ripple
−
−70
−
dB
Output Noise Density @ 1.0 kHz
5−7
−
−
150
−
nV/√Hz
RMS Output Noise Voltage (all versions)
Cout = 1.0 mF, Iout = 50 mA, F = 100 Hz to 1.0 MHz
5−7
Noise
−
35
−
mV
Output Rise Time (all versions) Cout = 1.0 mF, Iout = 50 mA,
10% of Rising ON Signal to 90% of Nominal Vout
5−7
trise
−
40
−
ms
−
−
−
−
125
°C
Other Voltages up to 5.0 V Available in 50 mV Increment Steps
Vout + 1.0 V < Vin < 6.0 V, TA = −40°C to +85°C, 1.0 mA < Iout < 80 mA
Other Voltages up to 5.0 V Available in 50 mV Increment Steps
LINE AND LOAD REGULATION, DROPOUT VOLTAGES
Line Regulation (all versions)
Iout = 30 mA
Iout = 60 mA
Iout = 80 mA
DYNAMIC PARAMETERS
THERMAL SHUTDOWN
Thermal Shutdown (all versions)
3. Voltage slope should be greater than 2.0 mV/ms
http://onsemi.com
3
MC33762
ORDERING INFORMATION
Device
Marking
Voltage Output
Package
MC33762DM−2525R2
MC33762DM−2525R2G
Micro8
2525
2.5 V
2528
2.8 V
3030
3.0 V
Micro8
(Pb−Free)
MC33762DM−2828R2
MC33762DM−2828R2G
Micro8
Micro8
(Pb−Free)
MC33762DM−3030R2
MC33762DM−3030R2G
Shipping †
4000 Units / Tape & Reel
Micro8
Micro8
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
DEFINITIONS
Load Regulation
Line Regulation
The change in output voltage for a change in output
current at a constant chip temperature.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse technique such that the average
chip temperature is not significantly affected. One usually
distinguishes static line regulation or DC line regulation (a
DC step in the input voltage generates a corresponding step
in the output voltage) from ripple rejection or audio
susceptibility where the input is combined with a frequency
generator to sweep from a few hertz up to a defined
boundary while the output amplitude is monitored.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 100 mV
below its nominal value (which is measured at 1.0 V
differential value). The dropout level is affected by the chip
temperature, load current and minimum input supply
requirements.
Thermal Protection
Output Noise Voltage
This is the integrated value of the output noise over a
specified frequency range. Input voltage and output current
are kept constant during the measurement. Results are
expressed in mVRMS.
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 125°C,
the regulator turns off. This feature is provided to prevent
catastrophic failures from accidental overheating.
Maximum Power Dissipation
Maximum Package Power Dissipation
The maximum total dissipation for which the regulator
will operate within its specs.
The maximum power package power dissipation is the
power dissipation level at which the junction temperature
reaches its maximum operating value, i.e. 125°C.
Depending on the ambient temperature, it is possible to
calculate the maximum power dissipation and thus the
maximum available output current.
Quiescent Current
The quiescent current is the current which flows through
the ground when the LDO operates without a load on its
output: internal IC operation, bias etc. When the LDO
becomes loaded, this term is called the Ground current. It is
actually the difference between the input current (measured
through the LDO input pin) and the output current.
http://onsemi.com
4
MC33762
Characterization Curves
Curves are Common to Both Regulators
4.5
185
GROUND CURRENT (mA)
3.5
QUIESCENT CURRENT (m A)
−40°C
25°C
85°C
4.0
3.0
2.5
2.0
1.5
1.0
180
175
170
0.5
0
0
20
40
60
OUTPUT CURRENT (mA)
80
165
−60
100
Figure 2. Ground Current versus
Output Current
−20
0
20
40
60
AMBIENT TEMPERATURE (°C)
80
100
Figure 3. Quiescent Current versus
Temperature
200
2.805
150
25°C
−40°C
100
50
OUTPUT VOLTAGE (V)
85°C
85°C
2.800
40°C
2.795
2.790
2.785
25°C
0°C
2.780
−20°C
−40°C
0
2.775
0
20
60
40
OUTPUT CURRENT (mA)
80
100
0
20
Figure 4. Dropout versus Output Current
40
60
OUTPUT CURRENT (mA)
80 mA
160
60 mA
140
120
30 mA
100
80
60
40
20
0
−60
1.0 mA
−40
−20
80
Figure 5. Output Voltage versus
Output Current
180
DROPOUT VOLTAGE (mV)
DROPOUT (mV)
−40
0
20
40
TEMPERATURE (°C)
60
80
Figure 6. Dropout versus Temperature
http://onsemi.com
5
100
100
MC33762
APPLICATION HINTS
Input Decoupling
Protections
As with any regulator, it is necessary to reduce the
dynamic impedance of the supply rail that feeds the
component. A 1.0 mF capacitor either ceramic or tantalum is
recommended and should be connected close to the
MC33762 package. Higher values will correspondingly
improve the overall line transient response.
The MC33762 hosts several protections, giving natural
ruggedness and reliability to the products implementing the
component. The output current is internally limited to a
maximum value of 180 mA typical while temperature
shutdown occurs if the die heats up beyond 125°C. These
values let you assess the maximum differential voltage the
device can sustain at a given output current before its
protections come into play.
The maximum dissipation the package can handle is given
by:
Output Decoupling
Thanks to a novel concept, the MC33762 is a stable
component and does not require any specific Equivalent
Series Resistance (ESR) neither a minimum output current.
Capacitors exhibiting ESRs ranging from a few mW up to
3.0 W can thus safely be used. The minimum decoupling
value is 1.0 mF and can be augmented to fulfill stringent load
transient requirements. The regulator accepts ceramic chip
capacitors as well as tantalum devices.
T
*T
A
P max + Jmax
R
qJA
If TJmax is limited to 125°C, then the MC33762 can
dissipate up to 395 mW @ 25°C. The power dissipated by
the MC33762 can be calculated from the following formula:
ǒ
Noise Performances
Ptot + V
Unlike other LDOs, the MC33762 is a true low−noise
regulator. Without the need of an external bypass capacitor,
it typically reaches the incredible level of 40 mVRMS overall
noise between 100 Hz and 100 kHz. To give maximum
insight on noise specifications, ON Semiconductor includes
spectral density graphics. The classical bypass capacitor
impacts the startup phase of standard LDOs. However,
thanks to its low−noise architecture, the MC33762 operates
without a bypass element and thus offers a typical 40 ms
startup phase.
in
I
Ǔ
(I ) ) ǒV * V outǓ
gnd out
in
I out
or
Vin max +
Ptot ) V out
I
gnd
I out
) I out
If a 80 mA output current is needed, the ground current is
extracted from the data−sheet curves: 4.0 mA @ 80 mA. For
a half 2.8 V MC33762 (2.8 V) operating at 25°C, the
maximum input voltage will then be 7.3 V.
Typical Applications
The following picture portrays the typical application of
the MC33762.
Input
1
8
2
7
3
6
Output 1
Output 2
5
4
MC33762
+
C3
1.0 mF
Regulator 1
On/Off
+
+
C1
C2
1.0 mF 1.0 mF
Regulator 2
R1
100 k
On/Off
R2
100 k
Figure 7. A Typical Application Schematic
As for any low noise designs, particular care has to be
taken when tackling Printed Circuit Board (PCB) layout.
Connections shall be kept short and wide. Layout example
as given in the MC33761 application hints can be used as a
starting basis.
http://onsemi.com
6
MC33762
Understanding the Load Transient Improvement
The MC33762 features a novel architecture which allows
the user to easily implement the regulator in burst systems
where the time between two current shots is kept very small.
The quality of the transient response time is related to
many parameters, among which the closed−loop bandwidth
with the corresponding phase margin plays an important
role. However, other characteristics also come into play like
the series pass transistor saturation. When a current
perturbation suddenly appears on the output, e.g. a load
increase, the error amplifier reacts and actively biases the
PNP transistor. During this reaction time, the LDO is in
open−loop and the output impedance is rather high. As a
result, the voltage brutally drops until the error amplifier
effectively closes the loop and corrects the output error.
When the load disappears, the opposite phenomenon takes
place with a positive overshoot. The problem appears when
this overshoot decays down to the LDO steady−state value.
During this decreasing phase, the LDO stops the PNP bias
and one can consider the LDO asleep (Figure 8). If by
misfortune a current shot appears, the reaction time is
incredibly lengthened and a strong undershoot takes place.
This reaction is clearly not acceptable for line sensitive
devices, such as VCOs or other Radio−Frequency parts.
This problem is dramatically exacerbated when the output
current drops to zero rather than a few mA. In this later case,
the internal feedback network is the only discharge path,
accordingly lengthening the output voltage decay period
(Figure 9).
The MC33762 cures this problem by implementing a
clever design where the LDO detects the presence of the
overshoot and forces the system to go back to steady−state
as soon as possible, ready for the next shot. Figure 10 and 11
show how it positively improves the response time and
decreases the negative peak voltage.
Figure 8. A Standard LDO Behavior when the Load
Current Disappears
Figure 9. A Standard LDO Behavior when the Load
Current Appears in the Decay Zone
Figure 10. Without Load Transient Improvement
Figure 11. MC33762 with Load Transient Improvement
http://onsemi.com
7
MC33762
MC33762 Has a Fast Startup Phase
Thanks to the lack of bypass capacitor the MC33762 is
able to supply its downstream circuitry as soon as the OFF
to ON signal appears. In a standard LDO, the charging time
of the external bypass capacitor hampers the response time.
A simple solution consists in suppressing this bypass
element but, unfortunately, the noise rises to an
unacceptable level. MC33762 offers the best of both worlds
since it no longer includes a bypass capacitor and starts in
less than 40 ms typically (Repetitive at 200 Hz). It also
ensures an incredible low−noise level of 40 mVRMS
100 Hz−100 kHz. The following picture details the typical
33762 startup phase.
Figure 12. Repetitive Startup Waveforms
TYPICAL TRANSIENT RESPONSES
Figure 13. Output is Pulsed from 2.0 mA to 80 mA
Figure 14. Discharge Effects from 0 to 40 mA
http://onsemi.com
8
MC33762
TYPICAL TRANSIENT RESPONSES
Figure 15. Load Transient Improvement Effect
Figure 16. Load Transient Improvement Effect
250
200
0
Vin = Vout + 1.0 V
TA = 25°C
Cout = 1.0 mF
RMS Noise, IO = 50 mA:
20 Hz − 100 kHz: 27 mV
20 Hz − 1.0 MHz: 30 mV
−10
−20
150
−40
(dB)
nV/sqrt Hz
−30
IO = 50 mA
10 mA
100
50
IO = 50 mA
−50
−60
−70
RMS Noise, IO = 10 mA:
20 Hz − 100 kHz: 29 mV
20 Hz − 1.0 MHz: 31 mV
0
100
10 mA
Vin = VO + 1.0 V
TA = 25°C
Cout = 1.0 mF
−80
−90
−100
1,000
10,000
100,000
f, FREQUENCY (Hz)
1,000,000
100
Figure 17. MC33762 Typical Noise Density Performance
1,000
10,000
100,000
f, FREQUENCY (Hz)
Figure 18. MC33762 Typical Ripple Rejection
Performance
3.5
IO = 1.0 mA
3.0
Z O (OHMS)
2.5
10 mA
2.0
1.5
80 mA
1.0
0.5
20 mA
0
100
1,000
1,000,000
10,000
100,000
f, FREQUENCY (Hz)
Figure 19. Output Impedance Plot
Cout = 1.0 mF, Vin = Vout + 1.0 V
http://onsemi.com
9
1,000,000
MC33762
PACKAGE DIMENSIONS
Micro8t
CASE 846A−02
ISSUE G
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. 846A−01 OBSOLETE, NEW STANDARD 846A−02.
D
HE
PIN 1 ID
E
e
b 8 PL
0.08 (0.003)
M
T B
S
A
S
SEATING
−T− PLANE
0.038 (0.0015)
MILLIMETERS
NOM
MAX
−−
1.10
0.08
0.15
0.33
0.40
0.18
0.23
3.00
3.10
3.00
3.10
0.65 BSC
0.40
0.55
0.70
4.75
4.90
5.05
DIM
A
A1
b
c
D
E
e
L
HE
MIN
−−
0.05
0.25
0.13
2.90
2.90
INCHES
NOM
−−
0.003
0.013
0.007
0.118
0.118
0.026 BSC
0.016
0.021
0.187
0.193
MIN
−−
0.002
0.010
0.005
0.114
0.114
MAX
0.043
0.006
0.016
0.009
0.122
0.122
0.028
0.199
A
A1
L
c
SOLDERING FOOTPRINT*
8X
1.04
0.041
0.38
0.015
3.20
0.126
6X
8X
4.24
0.167
0.65
0.0256
5.28
0.208
SCALE 8:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
Micro8 is a trademark of International Rectifier.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC33762/D