MC10H016 D

MC10H016
4−Bit Binary Counter
Description
The MC10H016 is a high−speed synchronous, presettable,
cascadable 4−bit binary counter. It is useful for a large number of
conversion, counting and digital integration applications.
http://onsemi.com
Features
• Counting Frequency, 200 MHz Minimum
• Improved Noise Margin 150 mV (Over Operating Voltage and
•
•
•
•
MARKING DIAGRAMS*
Temperature Range)
Voltage Compensated
MECL 10K™ − Compatible
Positive Edge Triggered
Pb−Free Packages are Available*
16
MC10H016L
AWLYYWW
CDIP−16
L SUFFIX
CASE 620
1
16
MC10H016P
AWLYYWWG
16
1
PDIP−16
P SUFFIX
CASE 648
1
1 20
20 1
PLLC−20
FN SUFFIX
CASE 775
A
WL
YY
WW
G
10H016G
AWLYYWW
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
*For additional marking information, refer to
Application Note AND8002/D.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 5 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2006
February, 2006 − Rev. 8
1
Publication Order Number:
MC10H016/D
MC10H016
VCC1
1
16
VCC2
Q1
2
15
Q2
Q0
3
14
Q3
TC
4
13
CP
PE
5
12
MR
CE
6
11
P3
PO
7
10
P2
VEE
8
9
P1
Table 1. TRUTH TABLE
CE
PE
MR
CP
L
H
L
H
X
X
L
L
H
H
X
X
L
L
L
L
L
H
Z
Z
Z
Z
ZZ
X
Function
Load Parallel (Pn to Qn)
Load Parallel (Pn to Qn)
Count
Hold
Masters Respond; Slaves Hold
Reset (Qn = LOW, TC = HIGH)
Z = Clock Pulse (Low to High); ZZ = Clock Pulse (High to Low)
Features include assertion inputs and outputs on each of the
four master/slave counting flip−flops. Terminal count is generated internally in a manner that allows synchronous loading at
nearly the speed of the basic counter.
Pin assignment is for Dual−in−Line Package
Figure 1. Pin Assignment
Table 2. MAXIMUM RATINGS
Symbol
Rating
Unit
VEE
Power Supply (VCC = 0)
Characteristic
−8.0 to 0
Vdc
VI
Input Voltage (VCC = 0)
0 to VEE
Vdc
Iout
Output Current
50
100
mA
TA
Operating Temperature Range
0 to +75
°C
Tstg
Storage Temperature Range
−55 to +150
−55 to +165
°C
Continuous
Surge
Plastic
Ceramic
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
http://onsemi.com
2
MC10H016
Table 3. ELECTRICAL CHARACTERISTICS (VEE = −5.2 V ±5%) (Note 1)
0°
Symbol
Characteristic
25°
75°
Min
Max
Min
Max
Min
Max
Unit
−
126
−
115
−
126
mA
−
−
450
1190
−
−
265
700
−
−
265
700
0.5
−
0.5
−
0.3
−
mA
IE
Power Supply Current
IinH
Input Current High
IinL
Input Current Low
VOH
High Output Voltage
−1.02
−0.84
−0.98
−0.81
−0.92
−0.735
Vdc
VOL
Low Output Voltage
−1.95
−1.63
−1.95
−1.63
−1.95
−1.60
Vdc
VIH
High Input Voltage
−1.17
−0.84
−1.13
−0.81
−1.07
−0.735
Vdc
VIL
Low Input Voltage
−1.95
−1.48
−1.95
−1.48
−1.95
−1.45
Vdc
All Except MR
Pin 12 MR
mA
1. Each MECL 10H™ series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been
established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 Ifpm is maintained.
Outputs are terminated through a 50 W resistor to −2.0 V.
Table 4. AC CHARACTERISTICS
0°
Symbol
Characteristic
25°
75°
Min
Max
Min
Max
Min
Max
Clock to Q
Clock to TC
MR to Q
1.0
0.7
0.7
2.4
2.4
2.4
1.0
0.7
0.7
2.5
2.5
2.5
1.0
0.7
0.7
2.7
2.6
2.6
Pn to Clock
CE or PE to Clock
2.0
2.5
−
−
2.0
2.5
−
−
2.0
2.5
−
−
Clock to Pn
Clock to CE or PE
1.0
0.5
−
−
1.0
0.5
−
−
1.0
0.5
−
−
Unit
tpd
Propagation Delay
ns
tset
Set−up Time
thold
Hold Time
fcount
Counting Frequency
200
−
200
−
200
−
MHz
tr
Rise Time
0.5
2.0
0.5
2.1
0.5
2.2
ns
tf
Fall Time
0.5
2.0
0.5
2.1
0.5
2.2
ns
ns
ns
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
http://onsemi.com
3
Figure 2. 4−Bit Binary Counter Logic Diagram
http://onsemi.com
4
CP
CLOCK
CE
MR
P0
PE
C
MR
CE
P0−P3
LSB
Q0−Q3
Tc
PE
1/2 10H109
MASTER
SLAVE
Q
P1
MASTER
Q
Q
SLAVE
Q
Q1
P2
MASTER
Q
Q
SLAVE
Q
Q2
P3
C
MR
CE
Tc
PE
1/2 10H109
C
MR
CE
P0−P3
Q0−Q3
Tc
PE
1/2 10H109
C
MR
CE
P0−P3
Q0−Q3
Max freq. is only OR gate delay below max when counting alone.
PN Counter 1 to 16 5
MC10H016 Cascaded for 5 Stage Presettable Counter
P0−P3
Q0−Q3
Tc
PE
1/2 10H109
Note that this diagram is provided for understanding of logic operation only. It should not be used for evaluation of
propagation delays as many gate functions are achieved internally without incurring a full gate delay.
Q
Q
Q0
C
MR
CE
P0−P3
MSB
Q0−Q3
Tc
PE
FO
Q
Q3
TC
MC10H016
MC10H016
ORDERING INFORMATION
Package
Shipping †
MC10H016FN
PLLC−20
46 Unit / Rail
MC10H016FNG
PLLC−20
(Pb−Free)
46 Unit / Rail
MC10H016FNR2
PLLC−20
500 / Tape & Reel
MC10H016FNR2G
PLLC−20
(Pb−Free)
500 / Tape & Reel
MC10H016L
CDIP−16
25 Unit / Rail
MC10H016P
PDIP−16
25 Unit / Rail
MC10H016PG
PDIP−16
(Pb−Free)
25 Unit / Rail
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
5
MC10H016
PACKAGE DIMENSIONS
20 LEAD PLLC
CASE 775−02
ISSUE E
0.007 (0.180) M T L−M
B
Y BRK
−N−
U
N
S
0.007 (0.180) M T L−M
S
S
N
S
D
−L−
−M−
Z
W
20
D
1
V
0.007 (0.180) M T L−M
S
N
S
R
0.007 (0.180) M T L−M
S
N
S
Z
T L−M
S
N
H
J
0.007 (0.180) M T L−M
S
−T−
VIEW S
SEATING
PLANE
F
0.007 (0.180) M T L−M
S
VIEW S
N
S
N
S
K
0.004 (0.100)
G
S
S
K1
E
G1
0.010 (0.250) S T L−M
S
VIEW D−D
A
C
0.010 (0.250)
G1
X
NOTES:
1. DIMENSIONS AND TOLERANCING PER ANSI Y14.5M,
1982.
2. DIMENSIONS IN INCHES.
3. DATUMS −L−, −M−, AND −N− DETERMINED WHERE TOP
OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD
PARTING LINE.
4. DIMENSION G1, TRUE POSITION TO BE MEASURED AT
DATUM −T−, SEATING PLANE.
5. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH.
ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE.
6. DIMENSIONS IN THE PACKAGE TOP MAY BE SMALLER
THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE
BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY
MISMATCH BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION
TO BE GREATER THAN 0.037 (0.940). THE DAMBAR
INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO
BE SMALLER THAN 0.025 (0.635).
http://onsemi.com
6
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.385
0.395
0.385
0.395
0.165
0.180
0.090
0.110
0.013
0.019
0.050 BSC
0.026
0.032
0.020
−−−
0.025
−−−
0.350
0.356
0.350
0.356
0.042
0.048
0.042
0.048
0.042
0.056
−−− 0.020
2_
10 _
0.310
0.330
0.040
−−−
MILLIMETERS
MIN
MAX
9.78
10.03
9.78
10.03
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
−−−
0.64
−−−
8.89
9.04
8.89
9.04
1.07
1.21
1.07
1.21
1.07
1.42
−−−
0.50
2_
10 _
7.88
8.38
1.02
−−−
N
S
MC10H016
PACKAGE DIMENSIONS
CDIP−16
L SUFFIX
CERAMIC DIP PACKAGE
CASE 620−10
ISSUE T
−A−
16
9
1
8
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION F MAY NARROW TO 0.76 (0.030)
WHERE THE LEAD ENTERS THE CERAMIC
BODY.
−B−
C
−T−
DIM
A
B
C
D
E
F
G
H
K
L
M
N
K
N
SEATING
PLANE
L
M
E
F
J
G
D
16 PL
0.25 (0.010)
16 PL
0.25 (0.010)
M
T A
M
−A−
9
1
8
B
F
S
S
PDIP−16
P SUFFIX
PLASTIC DIP PACKAGE
CASE 648−08
ISSUE R
16
T B
C
H
L
SEATING
PLANE
K
G
D
M
J
16 PL
0.25 (0.010)
M
T A
MILLIMETERS
MIN
MAX
19.05
19.93
6.10
7.49
−−−
5.08
0.39
0.50
1.27 BSC
1.40
1.65
2.54 BSC
0.21
0.38
3.18
4.31
7.62 BSC
0_
15 _
0.51
1.01
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
S
−T−
INCHES
MIN
MAX
0.750
0.785
0.240
0.295
−−− 0.200
0.015
0.020
0.050 BSC
0.055
0.065
0.100 BSC
0.008
0.015
0.125
0.170
0.300 BSC
0_
15 _
0.020
0.040
M
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740
0.770
0.250
0.270
0.145
0.175
0.015
0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008
0.015
0.110
0.130
0.295
0.305
0_
10 _
0.020
0.040
MILLIMETERS
MIN
MAX
18.80
19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0_
10 _
0.51
1.01
MECL 10H and MECL 10K are trademarks of Motorola, Inc.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Phone: 81−3−5773−3850
Email: [email protected]
http://onsemi.com
7
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
MC10H016/D