NCP1650 D

NCP1650
Power Factor Controller
The NCP1650 is an active, power factor correction controller that
can operate over a wide range of input voltages, and output power
levels. It is designed to operate on 50/60 Hz power systems. This
controller offers several different protection methods to assure safe,
reliable operation under any conditions.
The PWM is a fixed frequency, average current mode controller
with a wide complement of features. These features allow for both
flexibility as well as precision in it’s application to a circuit. Critical
components of the internal circuitry are designed for high accuracy,
which allows for precise power and current limiting, therefore
minimizing the amount of overdesign necessary for the power stage
components.
The NCP1650 is designed with a true power limiting circuit that will
maintain excellent power factor even in constant power mode. It also
contains features that allow for fast transient response to changing
load currents and line voltages.
www.onsemi.com
SO−16
D SUFFIX
CASE 751B
16
1
MARKING DIAGRAM
16
NCP1650G
AWLYWW
Features
•
•
•
•
•
•
•
•
•
•
•
•
Fixed Frequency Operation
Average Current Mode PWM
Continuous or Discontinuous Mode Operation
Fast Line/Load Transient Compensation
True Power Limiting Circuit
High Accuracy Multipliers
Undervoltage Lockout
Overvoltage Limiting Comparator
Brown Out Protection
Ramp Compensation Does Not Affect Oscillator Accuracy
Operation from 25 to 250 kHz
This is a Pb−Free Device
1
A
WL
Y
WW
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
PIN CONNECTIONS
Vin 1
16 OUTPUT
Vref 2
15 GND
14 CT
AC COMP 3
AC REF 4
13 RAMP COMP
AC INPUT 5
Typical Applications
12 IS−
FB/SD 6
• Server Power Converters
• Front End for Distributed Power Systems
11 Iavg−fltr
LOOP COMP 7
10 Iavg
PCOMP 8
9 Pmax
(Top View)
ORDERING INFORMATION
Device
NCP1650DR2G
Package
Shipping†
SOIC−16
(Pb−Free)
2500/Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2015
March, 2015 − Rev. 13
1
Publication Order Number:
NCP1650/D
NCP1650
PIN FUNCTION DESCRIPTION
Pin #
Function
1
VCC
Provides power to the device. This pin is monitored for undervoltage and the unit will not operate if the
VCC voltage is not within the UVLO range.
Description
2
Vref
6.5 V regulated reference output. This reference voltage is disabled when the chip is in the shutdown
mode.
3
AC
Compensation
4
AC REF
This pin accommodates a capacitor to ground for filtering and stability of the AC error amplifier. The AC
error amplifier is a transconductance amplifier and is terminated with an internal high impedance load.
5
AC Input
The rectified input AC rectified sinewave is connected to this pin. This information is used for the
reference comparator, maximum power circuit, and the average current compensation circuit.
6
Feedback/
Shutdown
7
Loop
Compensation
8
PCOMP
9
PMAX
10
Iavg
11
Iavgfltr
12
IS−
13
Ramp
Compensation
14
CT
15
Ground
Ground reference for the circuit.
16
Output
Drive output for power FET or IGBT. Capable of driving small devices, or can be connected to an external
driver for larger transistors.
Provides pole for the AC Reference Amplifier. This amplifier compares the sum of the AC input voltage
and the low frequency component of the input current to the reference signal. The response must be slow
enough to filter out most of the high frequency content of the current signal that is injected from the
current sense amplifier, but fast enough to cause minimal distortion to the line frequency information.
The DC output of the converter is reduced through a resistive voltage divider, to a level of 4.0 V, and
connected to this pin to provide feedback for the voltage regulation loop. This pin also provides an input
undervoltage lockout feature by disabling the chip until the divided output voltage exceeds 0.75 V. It can
also be used as a shutdown pin by shorting it to ground with an open collector comparator, or a small
signal transistor.
A compensation network for the voltage regulation loop, is connected to the output of the voltage error
amplifier at this pin.
A compensation network for the maximum power loop, is connected to the output of the power error
amplifier at this pin.
This pin allows the output of the power multiplier to be scaled for the desired maximum power limit level.
This multiplier is a proprietary switching design and requires both a resistor and capacitor to ground. The
value of this resistor is determined in conjunction with R10.
An external resistor with a low temperature coefficient is connected from this terminal to ground, to set
and stabilize the gain of the Current Sense Amplifier output that drives the Power Multiplier and the AC
error amplifier. This resistor should be of the same type as that used on pin 9. The value of this resistor
will determine the maximum average current that the unit will allow before limiting will occur.
A capacitor connected to this pin filters the high frequency component from the instantaneous current
waveform, to create a waveform that resembles the average line current.
Negative current sense input. Designed to connect to the negative side of the current shunt.
This pin biases the ramp compensation circuit, to adjust the amount of compensation that is added to the
instantaneous current and AC error amp outputs.
Timing capacitor for the internal oscillator. This capacitor adjusts the oscillator frequency.
www.onsemi.com
2
NCP1650
MAXIMUM RATINGS (Maximum ratings are those that, if exceeded, may cause damage to the device. Electrical Characteristics are
not guaranteed over this range.)
Rating
Power Supply Voltage (Operating) Output (Pin 16)
Current Sense Inverting Input (Pin 12)
Reference Voltage (Pin 2)
Reference Filter (Pin 4)
Symbol
Value
Unit
VCC
−0.3 to 20
V
V(IS−)
−0.5 to 1.0
V
Vref
−0.3 to 7.5
V
Ref fltr
−0.3 to 5.0
V
−0.3 to 6.5
V
All Other Inputs
Thermal Resistance, Junction−to−Air
0.1 in2 Copper
0.5 in2 Copper
qJA
Thermal Resistance, Junction−to−Lead (Pin 1) (Note 1)
qJL
°C/W
130
110
Maximum Power Dissipation @ TA = 25°C
°C/W
50
Pmax
0.77
W
Operating Temperature Range
TJ
−40 to 125
°C
Non−operating Temperature Range
TJ
−55 to 150
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. qJL is equivalent to PsiJL
ELECTRICAL CHARACTERISTICS (Unless otherwise noted: VCC = 14 volts, CT = 470 pF, C2 = 0.1 mF, TJ = 25°C for typical
values. For min/max values TJ is the applicable junction temperature.)
Characteristic
Symbol
Min
Typ
Max
Unit
Frequency
Fosc
90
100
110
kHz
Max Duty Cycle
dmax
0.95
0.97
−
−
Min Duty Cycle (Note 2)
dmin
−
0
5.0
%
Ramp Peak (Note 2)
VRpeak
−
4.0
−
V
Ramp Valley (Note 2)
OSCILLATOR
VRvalley
−
0.100
−
V
Ramp Compensation Peak Voltage (Pin 13) (Note 2)
−
−
4.0
−
V
Ramp Compensation Current (Pin 13) (Note 2)
−
−
400
−
mA
VOLTAGE ERROR AMPLIFIER
Input Bias Current (Note 2)
Ibias
−
0.2
0.6
mA
Input Offset Voltage (Note 2)
VIO
−
10
−
mV
Transconductance (TJ = −40°C to + 125°C)
gm
90
120
150
umho
IOsource
10
20
−
mA
IOsink
−10
−20
−
mA
Source Boost Current Threshold (Vpin6/Vref)
Vfb(boost+)
−
1.06
−
V/V
Sink Boost Current Threshold (Vpin6/Vref)
Vfb(boost−)
−
0.920
−
V/V
Source Boost Current (Vref + 0.4 V)
I(boost+)
150
230
−
mA
Sink Boost Current (Vref − 0.4 V)
I(boost−)
−150
−260
−
mA
Output Source (Vref + 0.2 V)
Output Sink (Vref − 0.2 V)
Boost Current (Vref = 4.0 volts nominal)
2. Verified by design.
www.onsemi.com
3
NCP1650
ELECTRICAL CHARACTERISTICS (continued) (Unless otherwise noted: VCC = 14 volts, CT = 470 pF, C2 = 0.1 mF, TJ = 25°C for
typical values. For min/max values TJ is the applicable junction temperature.)
Characteristic
Symbol
Min
Typ
Max
Unit
Input Offset Voltage (Note 3)
VIO
−
20
−
mV
Transconductance
gm
60
100
150
umho
IOsource
10
20
−
mA
IOsink
−10
−20
−
mA
Source Boost Current Threshold
Vfb(boost+)
−
1.175
−
V/V
Sink Boost Current Threshold
Vfb(boost−)
−
0.825
−
V/V
Source Boost Current (1.3 X Vref)
I(boost+)
150
250
−
mA
Sink Boost Current
I(boost−)
−150
−285
−
mA
Input Offset Voltage (Note 3)
VIO
−
20
−
mV
Transconductance
gm
60
100
150
umho
IOsource
25
70
−
mA
Output Sink (Pin 4 = 0 V, Pin 5 = 4 V)
IOsink
−25
−70
−
mA
AC Inverting Input Clamp Voltage (250 mA) (TJ = 25°C)
Vclamp
4.30
4.45
4.60
V
AC Inverting Input Clamp Voltage (250 mA) (TJ = −40°C to +125°C)
Vclamp
3.70
−
4.60
V
AV
−
2.0
−
V/V
Input Bias Current (Pin 11)
Ibias
−40
−50
−80
mA
Differential Input Voltage Range (Note 3)
VIdiff
−
−0.20
−
V
Input Offset Voltage
VIO
0
2.5
5.0
mV
Output Gain (150 mA/0.150 V) (Voltage Loop Outputs) (Note 3)
Av
−
1000
−
umho
Output Gain (150 mA/0.150 V) (Max Pwr Output) (R10 = 15 kW) (Note 3)
Av
−
1000
−
umho
funity
−
1.5
−
MHz
PWM Output Voltage Gain (k = VPWM+ / Vsense−) (Pin 13 = Open)
(TJ = −40°C to + 125°C)
Av
12.9
15
17
V/V
Current Limit Voltage Gain (k = Vace/a / Vsense−) (Vpin5 = 0, R10 = 15 k)
Av
13
15
17
V/V
k
13.4
15
17
V/V
ILIMthr
225
270
315
mV
ILIMdelay
−
300
−
nS
−
−
−
3.75
−
1.0
−
−
−
−
8.0
−
POWER ERROR AMPLIFIER (Vcomp = 2.0 V, Vref = 2.5 V)
Output Source (Vref + 0.2 V)
Output Sink (Vref − 0.2 V)
Boost Current (Vref = 2.5 V nominal)
AC ERROR AMPLIFIER
Output Source (Pin 4 = 4 V, Pin 5 = 0 V)
Gain from ACcomp to PWM+ (Av = VPWM+ / (VACcomp – Voffset)) (Note 3)
CURRENT SENSE AMPLIFIER
Bandwidth (Note 3)
Power Output Voltage Gain (k = Vpin10 / Vsense−) (TJ = −40°C to + 125°C)
Current Limit Threshold (Vpin5 = 0, Pin 13 = Open)
Current Limit Delay (0 to –450 mV Step) (Note 3)
REFERENCE MULTIPLIER
Dynamic Input Voltage Range
Ac Input (p−input) (Note 3)
Compensation Input (a−input) (Note 3)
Offset Voltage (a−input)
Multiplier Gain
k+
Vmax
Vmult out
(VACńVramp pk) (VLOOPcomp * Voffset)
(Note 3)
3. Verified by design.
www.onsemi.com
4
k
V
1.0/V
NCP1650
ELECTRICAL CHARACTERISTICS (continued) (Unless otherwise noted: VCC = 14 volts, CT = 470 pF, C2 = 0.1 mF, TJ = 25°C for
typical values. For min/max values TJ is the applicable junction temperature.)
Characteristic
Symbol
Min
Typ
Max
Unit
12.1
11.8
12.8
12.8
13.3
13.3
Vmax
−
3.75
−
V
IINbias
−
0.01
−
mA
Rsource
4.0
8.0
15
W
Rsink
3.0
8.0
15
W
Rise Time (CL = 1.0 nF, 20% to 80%)
tr
−
50
−
ns
Fall Time (CL = 1.0 nF, 20% to 80%)
tf
−
50
−
ns
VO(UV)
−
1.0
10
mV
4.0 Volt Reference (Pin 6) (TJ = 25°C)
Vref
3.94
4.00
4.06
V
4.0 Volt Regulation (TJ = −55°C to 125°C)
Vref
3.92
4.00
4.08
V
2.5 Volt Reference (Pmax, Pin 9)
Vref2.5
2.40
2.50
2.60
V
Buffered Output (Iload = 0 mA)
VrefOUT
6.24
6.50
6.76
V
DVrefOUT
0
4.0
40
mV
UVLO Startup Threshold (VCC Increasing)
VSU
10
10.5
11
V
UVLO Hysteresis (Shutdown Voltage = VSU – VH)
VH
0.3
0.5
0.7
V
Shutdown Startup Threshold (Pin 6) (Vout Increasing)
VSD
0.50
0.85
1.00
V
Shutdown Hysteresis (Pin 6)
VH
0.10
0.18
0.3
V
VOV
106.5
108
109.5
V/V
VOVdiff
−
50
−
mV
IBIAS
−
4.0
5.0
mA
IBshutdown
−
0.6
1.0
mA
MAXIMUM POWER MULTIPLIER
Multiplier Gain
Vpin9
4.0 R9
K+
[
(−Vpin12) Vpin5
R10
R9 = 47 k, R10 = 15 k
k
(TJ = 25°C)
(TJ = −40°C to +125°C)
Dynamic Input Voltage Range
Ac Input (p−input) (Note 4)
1.0/V
AC INPUT (Pin 5)
Input Bias Current
(Total bias current for both multipliers and current compensation amplifier)
DRIVE OUTPUT
Source Resistance (80 mA Load)
Sink Resistance (−80 mA Load)
Output Voltage in UVLO Condition
VOLTAGE REFERENCE
Load Regulation (Buffered Output, Io = 0 to 10 mA, VCC > 10 V)
UNDERVOLTAGE LOCKOUT/SHUTDOWN
OVERVOLTAGE PROTECTION
Overvoltage Voltage Trip Point (Vpin6/Vref)
Overvoltage Voltage Differential (VOV − Vboost+)
TOTAL DEVICE
Operational Bias Current (CL(Driver) = 1.0 nF, 100 kHz)
Bias Current in Undervoltage Mode
4. Verified by design.
www.onsemi.com
5
NCP1650
VCC
LOOP
COMP
4.24 V
200 mA
+
FB/SD
4V
3.68 V
ERROR
AMP
20 mA
+
+
-
REFERENCE
REGULATOR
VOLTAGE/POWER
ORing NETWORK
200 mA
+
0.85 V
UVLO
SHUTDOWN
PCOMP
POWER
MULTIPLIER
AC INPUT
REFERENCE
MULTIPLIER
2.5 V
POWER
AMP
+
-
1.08 Vref
+
OVERVOLTAGE
COMPARATOR
CURRENT
SHAPING
NETWORK
CONTROL
LOGIC
OUT
+
OSCILLATOR
CURRENT
SENSE
AMPLIFIER
−
GND
RAMP COMP
CT
Figure 1. Simplified Block Diagram
www.onsemi.com
6
IS−
NCP1650
UVLO or
SHUTDOWN
OVERVOLTAGE
COMPARATOR
DRIVE
LATCH Q
AC Error Amp + Ramp Comp + Inductor Current
PWM
4V
GND
OSCILLATOR
RAMP
OSCILLATOR
BLANKING PULSE
Figure 2. Timing Diagram
Typical Performance Characteristics
(Test circuits are located in the document TND307/D)
130
125
qJA (°C/W)
120
115
110
105
100
95
90
0
100
200
300
COPPER AREA
400
500
600
(mm2)
Figure 3. qJA as a Function of the Pad Copper
Area (1 oz. Cu Thickness) for a JEDEC Test PCB
www.onsemi.com
7
NCP1650
Typical Performance Characteristics
(Test circuits are located in the document TND307/D)
102
100 k
FREQUENCY (Hz)
101
CT (pF)
10 k
1k
100
99
98
97
96
−50
100
1.0
10
100
1000
0
25
50
75
100
TEMPERATURE (°C)
Figure 4. CT versus Frequency
Figure 5. Frequency versus Temperature
125
4.12
4.40
NOTE: Ramp Valley Voltage
is Zero for all Frequencies
4.35
NOTE: Valley
Voltage is Zero
4.30
4.10
RAMP PEAK (V)
PEAK RAMP VOLTAGE (V)
−25
FREQUENCY (kHz)
4.25
4.20
4.08
4.15
4.10
4.06
4.05
4.00
3.95
50
100
150
200
250
4.04
−50
300
−25
0
25
50
75
100
FREQUENCY (kHz)
TEMPERATURE (°C)
Figure 6. Ramp Peak versus Frequency
Figure 7. Peak Ramp Voltage versus
Temperature
99
6
98
5
DUTY CYCLE (%)
DUTY CYCLE (%)
0
97
96
95
94
125
4
3
2
1
93
0
0
50
100
150
200
250
300
0
50
100
150
200
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 8. Max Duty Cycle versus Frequency
Figure 9. Minimum Duty Cycle versus
Frequency
www.onsemi.com
8
250
NCP1650
300
30
200
20
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
Typical Performance Characteristics
(Test circuits are located in the document TND307/D)
100
0
−100
−200
−300
−0.6
10
0
−10
−20
−0.4
−0.2
0
0.2
0.4
−30
−0.3
0.6
PIN 6 VOLTAGE RELATIVE TO 4.0 V REF−BOOST CIRCUIT
−0.2
Figure 10. Voltage Amplifier Gain
0.1
0.2
0.3
40
30
OUTPUT CURRENT (mA)
300
OUTPUT CURRENT (mA)
0
Figure 11. Voltage Amplifier Gain
400
200
100
0
−100
−200
−300
−1.5
−0.1
PIN 6 VOLTAGE RELATIVE TO 4.0 V REF−LINEAR REGION
20
10
0
−10
−20
−30
−40
−1.0
−0.5
0
0.5
1.0
−50
−0.6
1.5
PIN 9 VOLTAGE RELATIVE TO 2.5 V REF−BOOST CIRCUIT
−0.4
−0.2
0
0.2
0.4
0.6
PIN 9 VOLTAGE RELATIVE TO 2.5 V REF−LINEAR REGION
Figure 12. Power Amplifier Gain
Figure 13. Power Amplifier Gain
5.0
PIN 11
4.5
4.0
PIN 10
OUTPUT (V)
3.5
IS− (pin 12)
100 mV/div
3.0
2.5
GND
2.0
1.5
Iavg fltr (pin 11)
200 mV/div
1.0
0.5
0
−50
GND
C11 = 1 nF
0
50
100
150
200
250
300 350
Ch 1 200 mV
BW
Ch 4
VIS− (mV)
M 1.00 ms
100 mVW BW
Ch 4 −58 mV
Figure 15. Current Sense Amplifier High
Frequency Response
Figure 14. Current Sense Amplifier Gain
www.onsemi.com
9
NCP1650
Typical Performance Characteristics
(Test circuits are located in the document TND307/D)
5.0
6.0
PIN 7 = 0 V
1.5 V
2V
2.5 V
Pmax, PIN 9 (V)
4.0
Vref, PIN 4 (V)
IS− = −0.2
5.0
3.0
2.0
−0.15
4.0
−0.1
3.0
2.0
−0.05
3V
1.0
1.0
−0.02
0
0
0
1.0
2.0
3.0
4.0
5.0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
VAC, PIN 5 (V)
VAC, PIN 5 (V)
Figure 16. Reference Multiplier Transfer
Function
Figure 17. Power Multiplier Transfer Function
10 k
4.01
RISE TIME
4.00
4.0 Vref (V)
C, PIN 16 CAPACITANCE (pF)
FALL TIME
1k
3.99
3.98
3.97
100
3.96
0
50
100
150
200
250
300
350
−50
−25
0
25
50
75
100
RISE/FALL TIME (ns)
TEMPERATURE (°C)
Figure 18. Capacitance versus 10−90% Drive
Rise and Fall Times
Figure 19. 4.0 Volt Reference versus
Temperature
2.51
125
6.51
25°C
6.50
Vref (V)
2.5 Vref (V)
−40°C
2.50
6.49
6.48
2.49
125°C
6.47
2.48
−50
6.46
−25
0
25
50
75
100
125
10
12
14
16
18
TEMPERATURE (°C)
VCC, VOLTAGE (V)
Figure 20. 2.5 Volt Reference versus
Temperature
Figure 21. Vref Line Regulation
www.onsemi.com
10
20
NCP1650
Typical Performance Characteristics
(Test circuits are located in the document TND307/D)
6.52
25°C
Vref
50 mV/div
Vref (V)
6.50
−40°C
10 mA
6.48
Vref Load
6.46
0 mA
125°C
6.44
0
2
4
6
8
10
2.0 ms/div
LOAD CURRENT (mA)
Figure 23. Vref Transient Response
Figure 22. Vref Load Regulation
7
−40°C
TURN ON
10.5
6
INPUT CURRENT (mA)
TURN ON/OFF VOLTAGE (V)
10.6
10.4
10.3
10.2
10.1
TURN OFF
10.0
9.9
−50
5
25°C
4
125°C
3
2
25°C
125°C
−40°C
1
0
−25
0
25
50
75
100
125
0
2
4
6
8
10
12
14
16
18
TEMPERATURE (°C)
INPUT VOLTAGE (V)
Figure 24. UVLO versus Temperature
Figure 25. Input Current versus Input Voltage
www.onsemi.com
11
20
NCP1650
Vout
Vout
R1
FB/SD
R1
6
FB/SD
Vref
6
2
NCP1650
Vref
R2
2
4.7 V
NCP1650
R2
R2
R2
ZENER DIODE
RESISTOR−DIODE NETWORK
Figure 26. Shutdown Override Circuit
Figure 27. Shutdown Override Circuit
(This circuit will not override the shutdown until the
chip has achieved it’s initial enable state)
5 V − Shutdown
0 V − Normal Operation
Vout
Vref
2
20 k
R1
33 k
BAS16LT1
AC COMP
FB/SD
6
NCP1650
3
MMBT2907AL
2N3904
R2
R3
0.33 mF
4.7 k
Figure 28. External Shutdown Circuit
NCP1650
C3
Figure 29. Soft−Start Circuit
www.onsemi.com
12
NCP1650
LOOP
COMP
7
1
4.24 V
VCC
200 mA
+
4V
ERROR
AMP
20 mA
+
FB/SD
6
6.5 V
Vref
REFERENCE
REGULATOR
VOLTAGE/POWER
ORing NETWORK
2
4V
3.68 V
200 mA
+
-
UVLO
+
Pmax
SHUTDOWN
0.85 V
9
PCOMP
+
1.08 Vref
8
a
POWER
MULTIPLIER
2.5 V
+
-
POWER
AMP
OVERVOLTAGE
COMPARATOR
p
AC INPUT
5
AC REF
AC REFERENCE
BUFFER
a
REFERENCE
MULTIPLIER
0.75 Vline + k ⋅ Iin = Vref
V−I
+
p
4V
S
+
-
4
25 k
4.5 V
AC ERROR
AMP
16 k
S
Q
PWM
R
DRIVER
AC COMP
OUTPUT
RAMP
COMPENSATION
3
16
20 k
+
+
OSCILLATOR
60 k
AVERAGE
CURRENT
COMPENSATION
CURRENT
SENSE
AMPLIFIER
−
GND
IS−
12
15
RAMP COMP 13
14 CT
Figure 30. Detailed Block Diagram
www.onsemi.com
13
Iavg 10 11 Iavg fltr
NCP1650
THEORY OF OPERATION
Introduction
Optimizing the power factor of units operating off of AC
lines is becoming more and more important. There are a
number of reasons for this.
There are a growing number of government regulations
requiring Power Factor Correction (PFC). Many of these are
originating in Europe. Regulations such as IEC1000−3−2
are forcing equipment to utilize input stages with topologies
other than a simple off−line front end which contains a
bridge rectifier and capacitor.
There are also system requirements that dictate the use of
PFC. In order to obtain the maximum power from an
existing circuit in a building, the power factor is very critical.
The real power available from such a circuit is:
Preal + Vrms
Irms
Unity power factor is defined as the current waveform
being in phase with the voltage, and undistorted. Therefore,
there are two causes of power factor degradation – phase
shift and distortion. Phase shift is normally caused by
reactive loads such as motors which are inductive, or
electroluminescent lighting which is highly capacitive. In
such a case the power factor is relatively simple to analyze,
and is determined by the phase shift.
PF + cos q
Where q is the phase angle between the voltage and the
current.
Reduced power factor due to distortion is more
complicated to analyze and is normally measured with AC
analyzers, although most circuit simulation programs can
also calculate power factor. One of the major causes of
distortion is rectification of the line into a capacitive filter.
This causes current spikes that do not follow the input
voltage waveform. An example of this type of waveform is
shown in the upper diagram in Figure 2.
A power converter with PFC forces the current to follow
the input waveform. This reduces the peak current, the rms
current and eliminates any phase shift.
The NCP1650 accomplishes this for both continuous and
discontinuous mode power converters.
PF
A typical off−line converter will have a power factor of
0.5 to 0.6, which means that for a given circuit breaker rating
only 50% to 60% of the maximum power is available. If the
power factor is increased to unity, the maximum available
power can be obtained.
There is a similar situation in aircraft systems, where a
limited supply of power is available from the on−board
generators. Increasing the power factor will increase the
load on the aircraft without the need for a larger generator.
PFC Operation
The basic PWM function of the NCP1650 is controlled by
a small block of circuitry, which comprises the DC
regulation loop and the PFC circuit. These components are
shown in Figure 26.
There are three inputs to this loop. They are the fullwave
rectified input sinewave, the instantaneous input current and
the DC output voltage.
The input current is forced to maintain a near unity power
factor due to the control of the AC error amplifier. This
amplifier uses information from the AC input voltage and
the AC input current to control the power switch in a manner
that provides good DC regulation as well as an excellent
power factor.
The reference multiplier sets a reference level for the input
fullwave rectified sinewave waveform. One of its inputs is
connected to the scaled down fullwave rectified sinewave,
and the other is connected to the output of the DC error
amplifier. The signal from the DC error amplifier adjusts the
level of the fullwave rectified sinewave on its output without
distorting it. To accomplish this, it is necessary for the
bandwidth of the DC error amp to be less than twice the
lowest line frequency. Typically it is set at a factor of ten less
than the rectified frequency (e.g. for a 60 Hz input, the
bandwidth would be 12 Hz).
V
I
v, i
t
OFF−LINE CONVERTER
V
I
v, i
t
PFC CONVERTER
Figure 31. Voltage and Current Waveforms
www.onsemi.com
14
NCP1650
+Bus
FB/SD
Verror(dc)
+
4V
LOOP
COMP
VOLTAGE
ERROR
AMP
4V
+
REFERENCE
MULTIPLIER
Vref
Verror(ac)
+
-
.75
DRIVE
PWM
Logic
1
PWM
Rac2
Verror(ac)′
AC ERROR
AMP
+
-
AC INPUT
Rac1
DRIVER
-
Vline
Verror(ac)
V−I
AC
REFERENCE
BUFFER
k ⋅ Iin
CURRENT
SENSE
AMPLIFIER
IS−
AVERAGE CURRENT
COMPENSATION
−Bus
REF FILTER
Figure 32. Simplified Block Diagram of Basic PFC Control Circuit
output so that the signal can be summed with the
instantaneous input switching current (Iin). The output of the
buffer is still Verrorac.
The key to understanding how the input current is shaped
into a high quality sine wave is the operation of the AC error
amplifier. The inputs of an operational amplifier operating
in its linear range, must be equal.
There are several secondary effects, that create small
differences between the inverting and non−inverting inputs,
but for the purpose of this analysis they can be considered to
be equal.
The fullwave rectified sinewave output of the reference
multiplier is fed into the non−inverting input of the AC error
amplifier. The inverting input to the AC error amplifier
receives a signal that is comprised of the input fullwave
rectified sinewave (which is not modified by the reference
multiplier), and summed with the filtered input current.
Since the two inputs to this amplifier will be at the same
potential, the complex signal at the inverting input will have
the same wave shape as the AC reference signal. The AC
reference signal (Vref) is a fullwave rectified sinewave, and
the AC input signal (Vline) is also a fullwave rectified
sinewave, therefore, the AC current signal (Iin), must also be
a fullwave rectified sinewave. This relationship gives the
formula:
AC Input
Vref
Vline
OSC
k ⋅ Iin
Vref
Vline + k ⋅ Iin
4 V ref
Verror(ac)
Vref + .75 · Vline ) (k · Iin)
GND
The Iin signal has a wide bandwidth, and its instantaneous
value will not follow the low frequency fullwave rectified
sinewave exactly, however, the output of the AC error
amplifier has a low frequency pole that allows the average
value of the .75 Vline + (k x Iin) to follow Vref. Since the AC
error amplifier is a transconductance amplifier, it is followed
by an inverting unity gain buffer stage with a low impedance
4 V ref
Verror(ac)′
Verror(ac)
GND
Figure 33. Typical Signals for PFC Circuit
www.onsemi.com
15
NCP1650
The difference between Verror(ac) and the 4.0 volt
reference, sets the window that the instantaneous current
will modulate in, to determine when to turn the power switch
off.
The switch is turned on by the oscillator, which makes this
a fixed frequency controller. Under normal operation, the
switch will remain on until the instantaneous value of
Verror(ac)′ reaches the 4.0 volt reference level, at which time
the switch will turn off.
Since the input current has a fundamental frequency that
is twice that of the line, the output filter must have poles
lower than the input current to create a reasonable DC
waveform. The output DC voltage is divided down via. an
external divider and fed back to the DC error amplifier.
Instantaneous Current Limit
Protection Features
The NCP1650 contains a number of features to protect the
device and circuit from overload and stressful conditions.
These include:
• Output voltage overshoot protection
• Low line input protection
• Instantaneous current limit
• Line frequency current limit
• Maximum power limit
Line Frequency Current Limit
The fastest protection available is a cycle−by−cycle
current limit feature.
The current sense amplifier has three outputs. One is the
instantaneous current in the inductor, and the other two are
average current waveforms. The instantaneous current
signal goes directly to the PWM and is terminated by an
internal 16 kW resistor. This current signal is added to the
output of the AC error amplifier and the ramp compensation
signal. The switch will conduct current until the sum of these
three signals reaches the 4.0 V reference of the inverting
input to the PWM comparator. The peak current is
determined by the value of the ramp compensation resistor
(R13) and the current shunt.
The output of the reference multiplier determines the
current that will be required for the unit to regulate. The sum
of the input voltage from the Average Current
Compensation amplifier and the averaged current signal
from the current sense amplifier must add to the level of the
reference multiplier. The output of this multiplier is clamped
to a 4.5 maximum level. The maximum average current is set
by R10.
This form of protection is slower than the cycle−by−cycle
current limiting, but faster than the maximum power limit
circuit.
Output Voltage Overshoot Protection
An overshoot comparator has been provided to monitor
the output voltage. Due to the slow transient response of a
PFC controller, a fast load dump can cause a large output
voltage transient to occur.
The overshoot comparator uses the same input as the
feedback and shutdown signals. Its reference is set 8%
higher than the reference used by the error amplifier. This
comparator will shutdown the output stage if the output
voltage exceeds the set level by 8%. The circuit will resume
operation once the voltage is reduced to within 8% of the set
level.
Maximum Power Limit
The NCP1650 can limit the output power to protect
against nuisance tripping of circuit breakers or other input
power restrictions. It should be understood that boost
regulators by design, can not be short circuit limited.
Operation of the power limiting circuit will reduce the
output voltage only to the level where it is equal to the peak
of the input line voltage. At this point, the rectified line
voltage will continue to provide output voltage through line
frequency rectification by means of the series rectifier
diode.
The input power of the converter is calculated by the
power multiplier. By multiplying the instantaneous input
voltage (AC input signal, pin 5) and the instantaneous input
current (averaged current sense amplifier output), the actual
input power is accurately calculated.
The power multiplier has a very low frequency pole which
converts the power to a filtered DC level. The power error
amplifier has a reference set at 2.5 volts. If the output of the
power multiplier reaches 2.5 volts, the power error amplifier
takes control of the loop via the ORing network and will
regulate a constant power output within the limits of the
power stage. It should be understood that once the output
voltage is reduced to a level equal to the peak of the input
voltage, the converter can no longer control the output
power.
The output power level is set by combination of the Iavg
resistor at pin 10 and the Pmax resistor at pin 9.
Low Line Input Protection
This feature uses the shutdown circuitry to assure that the
unit does not start under low line condition. PFC converters
typically are designed with an output voltage of 400 VDC.
To reduce this to the level of the 4.0 volt reference, a 100:1
ratio is required for the voltage divider to the FB/SD pin.
When the converter is energized, the output voltage will be
the peak line voltage. If the peak line voltage does not exceed
75 volts (0.75 volts at the FB/SD pin) the unit will not start.
This corresponds to a line voltage of 53 volts rms.
Application circuits have been provided in Figures 33
and 34 to override this feature if desired.
www.onsemi.com
16
NCP1650
OPERATING DESCRIPTION
DC Reference and Buffer
The internal DC reference is a precision bandgap design
with a nominal output voltage of 4.0 volts. It is temperature
compensated, and trimmed for a $1% tolerance of its
nominal voltage, with an overall tolerance over line and
temperature of $2%. To assure maximum stability, this is
only used as a reference so there is minimal loading on this
source.
The DC reference is fed into a buffer with a gain of 1.625
which creates a 6.5 volt supply. This is used as an internal
voltage to power many of the blocks inside of the NCP1650
and is also available for external use. The 6.5 volt reference
is designed to be terminated with at 0.1 mF capacitor for
stability reasons.
There is no buffer between the internal and external 6.5 V
supply, so care should be used when connecting external
loads. A short or overload on this voltage output will inhibit
the operation of the chip.
There is also a 2.5 volt reference on the power amplifier.
This is derived by a resistive voltage divider off of the 4.0 V
reference.
by the RC network on the output. This network creates a low
pass filter, and removes the high frequency content from the
original waveform.
INPUT A
V to I
CONVERTER
INPUT P
RAMP
+
-
Inverting Input
OUTPUT
NI Input
Undervoltage Lockout
An Undervoltage Lockout circuit (UVLO) is provided to
assure that the unit does not exhibit undesirable behavior at
low Vcc levels. It also reduces power consumption to a level
that allows rapid charging of the Vcc cap.
When the Vcc cap is originally charging, the UVLO will
hold the unit off, and in a low bias current mode until the Vcc
voltage reaches a nominal 10.5 volt level. At this point the
unit will begin operation, and the UVLO will no longer be
active. If the Vcc voltage falls to a level that is 0.5 volts
below the turn−on point, the UVLO circuit will again
become active.
When in the shutdown state, the UVLO circuit removes
power from all internal circuitry by shutting off the 6.5 volt
supply. The 4.0 volt reference remains active, and the UVLO
and Shutdown comparators are also active.
Figure 34. Simplified Multiplier Schematic
The multiplier ramp is generated by the internal oscillator,
and is the same signal as is used in the PWM. It will therefore
have the same frequency as the power stage.
It is not necessary for Input P (into the PWM comparator)
to be a DC signal, low frequency AC signals (relative to the
ramp frequency) work well also.
The gain of the multiplier is determined by the
current−to−voltage ratio of the V−I converter, the load
resistor of the output filter and the peak and valley points of
the sawtooth ramp. When the P input signal is at the peak of
the ramp waveform, the comparator will allow the A input
signal to pass without chopping it at all. This gives an output
voltage of the A current multiplied by the output filter
resistance. When the P input signal is at the ramp valley
voltage, the comparator is held low and no current is passed
into the output filter. Between these two extremes, the duty
cycle (and therefore, the output signal) is proportional to the
level of the P input signal.
The output filter is a parallel RC network. The pole for this
network needs to be greater than twice the highest line
frequency (120 Hz for a 60 Hz line), and less than the
switching frequency.
Reference Multiplier The two multipliers have different
rules for designing their filters. The reference multiplier
contains an internal loading resistor, with a nominal value of
25 kW. This is because the resistor that converts the A input
voltage into a current is internal. Making both of these
resistors internal, allows for good accuracy and good
temperature performance. Only a capacitor needs to added
externally to properly compensate this multiplier. It is not
Multipliers
The NCP1650 uses a new proprietary concept for the
Power and Reference multipliers. This innovative design
allows greatly improved accuracy compared to a
conventional linear analog multiplier. The multipliers use a
PWM switching circuit to create a scalable output signal,
with a very well defined gain.
One input (A) to the multiplier is a voltage−to−current
(V−I) converter. By converting the input voltage into a
current, an overall multiplier gain can be accomplished. In
addition, there will be no error in the output signal due to the
series rectifier.
The other signal (Input P) is inputted into the PWM
comparator. This selects a pulse width for the comparator
output. The current signal from the V−I converter is factored
by the duty cycle of the PWM comparator, and then filtered
www.onsemi.com
17
NCP1650
recommended that an external resistor be used at the “Ref
Gain” pin, due to tolerance variations of the internal
resistances.
The voltage−to−current conversion is performed in the
Voltage/Power ORing network. This circuit also limits the
maximum input signal (from the error amplifier) to 3 volts.
Power Multiplier/Current Sense Amplifier There is no
voltage−to−current converter on the power multiplier. The
current output of the current sense amplifier is used for the
analog input with no scaling.
The power multiplier requires an external resistor as well
as an external capacitor. The value of the resistor at pin 9
(max power) will depend on the value of the resistor used at
pin 10 for the current gain and the maximum desired output
power of the converter. These resistors should be the same
style of resistor and have the same temperature coefficients
for best performance.
The gain of the power multiplier is based on the values of
external components on this multiplier as well as the current
sense amplifier. The current sense amplifier output that
drives the power multiplier has its gain controlled by R9 and
R10, and is filtered by a capacitor on pin 11 which removes
the high frequency content from the inductor current signal.
The gain for the power multiplier can be calculated as
follows:
(1.) V9 + ICS
R9
Multiplier
AC Ref
+
25 k
AC Error
Amplifier
There is a 1 k resistor between the AC Ref pin and the AC
Error Amplifier for ESD protection. Due to this resistor, the
voltage on pin 4 will exceed 4.5 volts under some conditions,
but the maximum voltage at the non−inverting AC Error
Amplifier input will be clamped at 4.5 volts.
Feedback/Shutdown
The FB/SD pin is a multiple function pin. Its primary
function is to provide an input to the error amplifier for
sensing of the output voltage. The signal at this pin is also
sensed by an internal comparator that will shutdown the unit
if the voltage falls below 0.75 volts.
The feedback circuit applies the signal to the
non−inverting input of the voltage loop error amp. The other
input of the error amp is connected to the internal 4.0 volt
reference. The output of a voltage divider from the high
voltage DC output to ground, feeds this pin.
The shutdown function can be used for multiple purposes
including overvoltage, undervoltage or hot−swap control.
An external transistor, open collector or open drain gate,
connected to this pin can be used to pull it low, which will
inhibit the operation of the chip, and change the operating
state to a low power standby mode. An example of a
shutdown circuit is shown in Figure 36.
The shutdown circuit is designed such that under normal
line conditions the unit will be on. At startup, the AC line is
rectified and charges up the output capacitor. Under normal
line conditions, the output voltage will be great enough to
apply more than 1.0 volt to this pin and the circuit will
commence switching. If the unit is turned on into a low line
condition, the voltage at this pin will not allow the unit to
start.
Figures 33 and 34 shown circuits that can be used to
disable the shutdown function. Both of these circuits limit
the minimum voltage that can appear at the FB/SD input
when the chip is properly biased, while not interfering with
the 4.0 volt level that pin 6 sees when the unit is operating
properly.
(VacńVramp)
and,
15ńR10
Since the pole at pin 12 is much greater than twice the line
frequency we can ignore the effects of the capacitor on this
pin. VCS is the differential current sense rms input voltage.
Equations 1 and 2 can be rearranged to give the gain of the
multiplier:
(3.) V9 +
4.5 V
Figure 35. Reference Multiplier Clamp Circuit
Where:
ICS is the rms value of the average current out of the current
sense amplifier
R9 is the resistor value at pin 9 (Ohms)
Vac is the rms voltage at pin 5
Vramp is the sawtooth p−p ramp voltage (4.0 volts)
(2.) ICS + VCS
1k
3.75 @ R9 @ VCS @ Vac
R10
This gain equation gives the output voltage of the
multiplier, where the inputs are the AC fullwave rectified
sinewave and the current sense input signal.
Ramp Compensation
The Ramp Compensation pin allows the amount of ramp
compensation to be adjusted for optimum performance.
Ramp compensation is necessary in a current mode
www.onsemi.com
18
NCP1650
converter to stabilize the units operation when the duty cycle
is greater than 50%.
The amount of compensation required is dependent on
several variables, including the boost inductor value, and the
desires of the designer. The value should be based on the
falling di/dt of the inductor current. For a boost inductor with
a variable input voltage, this will vary over the AC input
cycle, and with changes in the input line. A di/dt chart is
included in the design spreadsheet that is available for the
NCP1650.
This pin is a buffered output of the oscillator, which
provides a voltage equal to the ramp on the oscillator CT pin.
A resistor from this pin to ground, programs a current that
is transformed via a current mirror to the non−inverting
input of the PWM comparator.
The ramp voltage due to the inductor di/dt at the input to
the PWM comparator is the current shunt voltage at pin 11
multiplied by 15, which is the gain of the current amplifier
output that feeds the PWM.
Current
Sense
Amp
i
CT + 47, 000ńf
Where CT is in pF and f is in kHz.
It is important not to load the capacitor on this pin, since
this could affect the accuracy of the frequency as well as that
of the multipliers which use the ramp signal. Any use of this
signal should incorporate a high impedance buffer.
Due to the required accuracy of the peak and valley ramp
voltages, the NCP1650 is not designed to be synchronized
to the frequency of another oscillator.
AC Ref
Buffer
1.6i
Average Current Compensation
The Peak Current Compensation circuit adjusts the
maximum current that can occur before the controller limits
the current. This allows for higher levels of current under
low line conditions than at high line.
The input signal to this amplifier is the input fullwave
rectified sinewave. The amplifier is a unity gain amplifier,
with a voltage divider on the output that attenuates the signal
by a factor of 0.75. This scaled down fullwave rectified
sinewave is summed with the low frequency current signal
out of the current sense amplifier.
The sum of these signals must equal the signal at the
inverting input to the AC error amplifier, which is the output
of the reference multiplier. Since there is a hard limit of
4.5 volts at the inverting input, the sum of the line voltage
plus the current cannot exceed this level.
A typical universal input design operates from 85 to
265 vac, which is a range of 3.1:1. The output of the Average
Current Compensation amplifier will change by this amount
to allow the maximum current to vary inversely to the line
voltage.
+
16 k
Oscillator
pin with a saturated transistor. A hysteretic comparator
monitors that ramp signal and is used to switch between the
current source and discharge transistor. While the cap is
charging, the comparator has a reference voltage of
4.0 volts. When the ramp reaches that voltage, the
comparator switches from the charging circuit to the
discharge circuit, and its reference changes from 4.0
to X0.5 volts (overshoot and delays will allow the valley
voltage to reach 0 volts).
The relationship between the frequency and timing
capacitor is:
PWM
Comparator
+
-
13
Ramp Compensation
RRC
Figure 36. Ramp Compensation Circuit
The current mirror is designed with a 1:1.6 current ratio.
The ramp signal injected can be calculated by the following
formula:
VRcomp +
1.6 Voscpk 16 k
RRC
+ 102
RRC
Where:
VRcomp = Peak injected ramp signal (v)
Driver
The output driver can be used to directly drive a FET, for
low and medium power applications, or a larger driver for
high power applications.
It is a complementary MOS, totem pole design, and is
capable of sourcing and sinking over 1.5 amps, with typical
rise and fall times of 30 ns with a 1.0 nF load. The totem pole
output has been optimized to minimize cross conduction
current during high speed operation.
Additional internal circuitry has been added to keep the
Driver in its low state whenever the Undervoltage Lockout
is active. This characteristic eliminates the need for an
external gate pulldown resistor.
RRC = Ramp compensation resistor (kW)
Oscillator
The oscillator generates the sawtooth ramp signal that sets
the switching frequency, as well as sets the gain for the
multipliers. Both the frequency and the peak−to−peak
amplitude are important parameters.
The oscillator uses a current source for charging the
capacitor on the CT pin. The charge rate is approximately
200 mA and is trimmed to maintain an accurate, repeatable
frequency. Discharge is accomplished by grounding the CT
www.onsemi.com
19
NCP1650
Error Amplifiers
The NCP1650 has three error amplifiers. These amplifiers
regulate the DC output voltage, the maximum output power,
and shape the AC reference fullwave rectified sinewave
signal.
All three of these are transconductance amplifiers.
Transconductance amplifiers differ from voltage amplifiers
in that the output is a high impedance with a controlled
voltage−to−current gain (i.e. the output current is
proportional to the differential input voltage). The gain of a
transconductance amplifier is determined by the equation:
amplifier does not contain a boost circuit, and has a constant
transconductance across its operating range.
Voltage and Power ORing Network
The ORing network for the voltage and power amplifiers
are inverting transconductance amplifiers. The network uses
an internal reference of approximately 3.0 volts. Its gain is:
4 + 3 V * Vin
Iout + (Vref * Vin) ·
3,125
12.5 k
Where the 12.5 k is the internal resistor, and 4 is the gain
of the current mirror.
Av + gm RL
Voltage Error Amplifier The voltage loop has a low
bandwidth amplifier, which is referred to simply as “Error
Amp” on the block diagram. This amplifier compares the
output DC voltage to the 4.0 volt reference and generates an
error signal which is used to adjust the AC reference voltage
from the reference multiplier.
The voltage error amplifier has a nominal gain of
100 umhos (or 0.0001 amps/volt). This means that an input
voltage differential of 10 mv would cause the output current
to change by 1.0 mA. The maximum output current for this
amplifier in its normal operating range is 50 mA.
This amplifier is a switched gain transconductance
amplifier, that increases the output current (or gain) when
the differential input voltage exceeds the reference voltage
by +6% or −8% the output current is increased to 250 or
–300 mA respectively. This boost circuit allows for rapid
changes to line or load transients by increasing the dv/dt of
the output capacitance of the amplifier.
Power Error Amplifier The power loop has a low
bandwidth error amplifier which is referred to as the “Power
Amp”. This amplifier performs a similar function to the
Error Amp, only it generates an error signal that holds the
power to a constant level.
The power error amplifier has a nominal gain of
100 umhos (or 0.0001 amps/volts). The maximum output
current for this amplifier in its normal operating range is
20 mA. It is also a switched gain transconductance amplifier
similar to the voltage error amplifier, however, the
thresholds are different.
AC Error Amplifier The third error amplifier, is the “AC
error amp”. It requires a higher bandwidth than the voltage
or power error amplifiers. This amplifier forces a signal
which is the sum of the current and input voltage to equal the
AC reference signal from the reference multiplier.
The AC error amplifier has a nominal gain of 100 umhos
(or 0.0001 amps/volt). The maximum output current for this
amplifier in its normal operating range is 20 mA. This
FB/SD
6
VOLTAGE
+ AMP
CURRENT
MIRROR
i
Vin
+
8
4i
3.0 V
POWER
AMP
12.5 k
To
Reference
Multiplier,
Input a
COMP
Figure 37. Voltage/Power ORing Network
The amplifier (voltage or power) with the highest output
voltage will control the loop, as the buffer transistor from the
other amplifier will be in cutoff. As the output voltage of an
amplifier increases, it’s contribution to the current sink will
increase, and the current driving the current mirror will
decrease, thus the output of the current mirror will decrease.
The current mirror output feeds the analog (a) input to the
reference multiplier.
Overvoltage Comparator
For a load transient, in which the current is suddenly
reduced, the output voltage will overshoot. This circuit, will
minimize the overshoot, and effectively decrease the
response time of the loop.
A comparator is provided to monitor the feedback voltage
and shut down the PWM in the event that the output exceeds
8% of the designed output voltage. The feedback voltage is
supplied to this comparator from pin 6, which is the same
signal that the voltage error amplifier uses to regulate the DC
voltage loop.
www.onsemi.com
20
NCP1650
Current Sense Amplifier
The current sense amplifier is a wide bandwidth amplifier
with a differential input. It consists of a differential input
stage, a high frequency current mirror and a low frequency
current mirror, for a total of three current outputs. Two of
them (AC Error Amplifier and Power Multiplier) are
generated from the i2 mirror, and their waveforms have been
filtered to resemble the average value of the input current.
The third output is the instantaneous inductor current and is
generated from the i1 mirror which directly feeds the input
of the PWM.
CURRENT
MIRROR
i1
i1
across an internal 15 kW resistor, and filtered by a capacitor
at pin 11. This signal, when properly filtered, will be the 2x
line frequency fullwave rectified sinewave. The filter pole
on pin 11 should be far enough below the switching
frequency to remove most of the high frequency component,
but high enough above the line frequency so as not to cause
significant distortion to the input fullwave rectified
sinewave waveform.
For a 100 kHz switching frequency and a 60 Hz line
frequency, a 10 kHz pole will normally work well. The
capacitor at pin 11 can be calculated knowing the desired
pole frequency by the equation:
C11 + 10.5
f
CURRENT
MIRROR
i1
i2
i2
Where:
C11 = Pin 11 capacitance (nF)
f = pole frequency (kHz)
i2
PWM
Pwr Mult
1k
1k
12
+
-
15 k
IS−
11
or, for a 10 kHz pole, C11 would be 1.0 nF.
AC Error
Amp
Iavg fltr
10
The gain of the low frequency current buffer is set by the
value of the resistor at pin 10. The value of R10 affects the
operation of the AC error amplifier as well as the maximum
power level. Power multiplier gain calculations are included
in the description of that circuit.
Iavg
R10
C11
PWM and Logic
The PWM and logic circuits are comprised of a PWM
comparator, an RS flip−flop (latch) and an OR gate. The
latch has two Set inputs and one Reset input. The Reset input
is dominant over the PWM Set input, but the Overshoot
Comparator Set input is dominant over the Reset input. The
two Set Inputs are effectively OR’ed together although their
dominance varies.
The NCP1650 uses a standard Pulse Width Modulation
scheme based on a fixed frequency oscillator. The oscillator
outputs a ramp waveform as well as a pulse which is
coincident with the falling edge of the ramp. The pulse is fed
into the PWM latch and AND gate that follows. During the
pulse, the latch is reset, and the output drive is in it’s low state.
On the falling edge of the pulse, the output drive goes high
and the power switch begins conduction. The instantaneous
inductor current is summed with the AC error amplifier
voltage and the ramp compensation signal to create a
complex waveform that is compared to the 4.0 volt reference
signal on the inverting input to the PWM comparator. When
the signal at the non−inverting input to the PWM comparator
exceeds 4.0 volts, the output of the PWM comparator
changes to a high state which drives one of the Set inputs to
the latch and turns the power switch off until the next
oscillator cycle. Figure 40 shows the relationships of the
oscillator and logic signals.
There are two override signals to the normal
cycle−by−cycle PWM operation. The UVLO circuit feeds
directly into the AND gate and will inhibit operation until
the input voltage is in a valid range. The Overshoot
Figure 38. Current Sense Amplifier
The input to the current sense amplifier is a common base
configuration. The voltage developed across the current
shunt is sensed at the Is− input. The amplifier input is
designed for negative going voltages only; the power stage
should resemble the configuration of the circuit in Figure 39.
Caution should be exercised when designing a filter
between the shunt resistor and this input, due to the low
impedance of this amplifier. Any series resistance due to a
filter, will create an offset of:
VOS + 50 mA
Rexternal
which will add a negative offset to the current signal. The
effect of this is that current information will be lost when the
current signal is below the offset level. This will be a
problem mainly at light loads and near the zero crossings.
The voltage across the current shunt resistor is converted
into a current (i1), which drives a current mirror. The output
of the i1 current mirror is a high frequency signal that is a
replica of the instantaneous current in the inductor. The
conversion of the current sense signal to current i1 is:
i1 + Vis−ń1 k
The PWM output sends that information directly to the
PWM input where it is added to the AC error amp signal and
the ramp compensation signal.
The other output of the i1 mirror provides a voltage signal
to a buffer amplifier. This signal is the result of i1 dropped
www.onsemi.com
21
NCP1650
Comparator monitors the output voltage and will shutdown
operation of the PWM circuit if the output voltage exceeds
8% above the normal regulation level. The Overshoot
Comparator signal is fed into the second Set input to the
latch.
The buffer amplifier, converts the input voltage to a
current by creating a current equal to the voltage difference
between the AC error amplifier output and the 2.9 volt
reference dropped across the 14 kW resistor. The bipolar
transistor level shifts the voltage and maintains the proper
current into the current mirror. The current mirror has a 1:2
ratio and delivers the output current to the PWM input. This
current is summed with the currents of the ramp
compensation signal and the instantaneous current signal to
determine the turn−off point in the switching cycle.
AC Reference Buffer
The AC reference buffer converts the voltage generated
by the AC error amplifier to be converted into a current to
be summed with the ramp compensation signal and the
instantaneous current signal.
Soft−Start Circuit
The AC error amplifier has been configured such that a
low output level will cause the output duty cycle to go to
zero. This will have the effect of soft−starting the unit at
turn−on, since the output is coupled to ground through a
capacitor.
There will be an initial offset of the output voltage due to
the output current and the resistor at pin 3. For example, if
the output is saturated in the high state at turn on, it will
source 50 mA. If pin 3 is terminated with a 2.2 kW resistor
and a 0.01 F capacitor, the initial step will be:
CURRENT
MIRROR
i1
2 X i1
2.9 V
AC
Comp
3
AC
ERROR
AMP
+
-
14 k
+
-
16 k
PWM,
Ramp
Comp
Current
Sense
Amp
50 mA
2.2 k + 0.11 volts
and the rate of rise will be:
Unity Gain Amplifier
50 mAń0.01 mF + 5 mvńms
Figure 39. AC Reference Buffer Schematic
or, 560 ms until the output is at 2.9 volts, which corresponds
to full duty cycle.
An external soft−start circuit can be added, as shown in
Figure 29, if additional time is desired.
The buffer’s transfer function is:
iout + (2.9 V * Vac)ń7 k
www.onsemi.com
22
NCP1650
DESIGN GUIDELINES
D1
VCC
LOOP COMP
Vin
D2
7
Cin
D3
4.24 V
R7
D4
+
-
4V
ERROR
AMP
FB/SD
C7
1
6
4V
PCOMP 3.68 V
+
-
9
C8
Vref
Cref
VOLTAGE/POWER
ORing NETWORK
+
-
+
0.85 V
UVLO
SHUTDOWN
POWER
AMP
a
POWER
MULTIPLIER
C9
2.5 V
+
-
1.08 Vref
INRUSH
LIMITER
(OPTIONAL)
+
4V
Pmax
R9
0.1 mF
2
REFERENCE
REGULATOR
8
R8
6.5 V
OVERVOLTAGE
COMPARATOR
p
Rac1
a
REFERENCE
MULTIPLIER
AC INPUT
5
AC REF
AC
REFERENCE
BUFFER
AC ERROR AMP
+
-
p
L1
S
V−I
0.75 Vline +
k ⋅ Iin = Vref
4V
+
S
Q
PWM
16 k
R
D5
4
25 k
4.5 V
RDC1
Rac2
DRIVER
AC COMP
Cac
3
C4
R3
GND
16
Cout
to FB
RDC2
20 k
+
+
C3
Q1
OUT
RAMP
COMPENSATION
OSCILLATOR
60 k
AVERAGE CURRENT
COMPENSATION
CURRENT
SENSE
AMPLIFIER
Rshunt
15
IS−
−
12
13
RAMP
COMP
14
R13
CT
CT
Iavg 10 11 Iavg fltr
R10
C11
Note: This is a theoretical design, and it is not implied that a circuit designed by this procedure will operate properly without normal
troubleshooting and adjustments as are common with any power conversion circuit. ON Semiconductor provides a spread sheet that
incorporates the following equations, and will calculate the bias components for a circuit using the above schematic.
Figure 40. Typical Application Schematic
Basic Specifications
The design of any power converter begins with a basic set
of specifications. As a minimum, the following parameters
should be known before beginning:
(Maximum rated output power)
Pomax
Vrmsmin (Minimum operational line voltage)
Vrmsmax (Maximum operational line voltage)
(Nominal switching frequency)
fswitch
Vout
(Nominal regulated output voltage)
Most of these parameters will be dictated by system
requirements. The output voltage may not be defined. In
general, it should be slightly greater than the peak of the line
waveform at high line. For a 265 vrms input, the peak line
voltage would be 375 volts, and 400 volts is a standard
output voltage. In no case should it be less than the peak
input line voltage.
Inductor
For an average current mode, fixed frequency PFC
converter, there is no magic formula to determine the
optimum value of the inductor. There are several trade−off’s
that should be considered. These include peak current vs.
average current, and switching losses vs. core losses. All of
these are a function of inductance, line and load. These
parameters determine when the converter is operating in the
continuous conduction mode and when it is operating in the
discontinuous conduction mode.
www.onsemi.com
23
NCP1650
For a first approach, the following formula will give the
inductance value that will cause the peak current to be a
fraction of the peak line frequency current.
L+
T · Vin2
2 · I% · Pout
ǒ
1*
Ǹ2 · V
in
Vout
Using the ON Semiconductor spreadsheet, a value of
250 mH allows for continuous mode operation at full load
and most input voltages. At the high line value of 265 vac,
the unit will operate in the continuous mode from 30° to
150°, and discontinuous when the input voltage is near zero.
Using information from the ON Semiconductor
spreadsheet the inductor can either be specified to a
magnetics company to design, or can be designed by the
Magnetics Inc. software. In either case, the critical
information for the inductor design, (inductance, maximum
average current, peak−to−peak ripple current, and switching
frequency) can be obtained from the spreadsheet.
If a secondary winding is desired to provide a bias supply,
it should provide a minimum of 11.8 volts (to exceed the
UVLO spec) and a maximum of 18 volts. The secondary
should be connected such that it conducts when the power
switch is off. This will create an output voltage that varies
with the input voltage, and near the zero crossings of the line
frequency will have a peak voltage equal to the regulated
output voltage divided by the turns ratio. The filter cap on the
Vcc pin needs to be of sufficient size to hold the voltage up
over between the zero crossings.
Ǔ
Where:
L is the inductance (mH)
T is the switching period (ms)
Vin is the minimum rms line voltage (v)
I% is the percent switching current ripple relative to the line
current (.xx)
Pout is the maximum output power (w)
Vout is the output voltage (v)
So for the following unit:
Vin = 85 vrms
Vout = 400 VDC
Pmax = 1000 watts
T = 10 ms (100 kHz)
I% = .30
Oscillator
The relationship between the frequency and timing
capacitor is:
the inductance would be 84 mH.
CT + 47, 000ńf
Ǹ2 · P
out
I max +
Vin
Where CT is in pF and f is in kHz.
The maximum low frequency line current would be
determined at full load and low line, or:
where the definitions of Pout and Vin are as in the above
equation. For the above conditions, Imax would be
16.6 amps. The peak current in the inductor at full load and
low line would be 30% greater than this, or 21.6 amps.
For thermal calculations the transformer will have to pass
11.8 amps rms, and not saturate with a peak current of
21.6 amps.
There are several options available for the design of
inductors. You can contact a magnetics manufacturer, such
as Coiltronics (cooperet.com) or inductor designs can be
made simply with the use of programs such as the DC
inductor design program from Magnetics Inc. This software
is free at their website, www.mag−inc.com.
Using the equation provided, and the following variables:
AC Voltage Divider
The voltage divider from the input rectifiers to ground is
a simple but important calculation. For this calculation it is
necessary to know the maximum line that the unit can
operate at. The peak input voltage will be:
Vinpeak + 1.414
Vrms max
The maximum voltage at the AC input (pin 5) is 3.75 volts
(this is true for both multipliers).
If the maximum line voltage is 265 vac, the peak input
voltage is:
Vinpeak + 1.414
265 Vrms + 375 Vpk
To keep the power dissipation reasonable for a ½ watt
resistor (Rac1), it should dissipate no more than ¼ watt.
Depending on environmental conditions, further derating
may be required. The power in this resistor is:
T = 10 ms (f = 100 kHz)
Vrms = 265 v
Vo = 400 VDC
Pmax = 1000 watts
I% = 30
PRac1 + (375 v * 3.75 v)2ńRac1 + .25 watts
so : Rac1 + 551 kOhms
To minimize dissipation, use the next largest standard
value, or 560 kOhms.
Then, Rac2 + 3.75 vń((375 v * 3.75 v)ń560 k)
+ 5.6 kOhms
the inductance would be 74 mH.
www.onsemi.com
24
NCP1650
Current Sense Resistor/Ramp Compensation
The combination of the voltage developed across the
current sense resistor and ramp compensation signal, will
determine the peak instantaneous current that the power
switch will be allowed to conduct before it is turned off.
The vector sum of the three signals that combine to create
the signal at the non−inverting input to the PWM comparator
must add up to 4.0 volts in order to terminate the switch
cycle. These signals are the error signal from the AC error
amp, the ramp compensation signal, and the instantaneous
current. For a worst case condition, the output of the AC
error amp could be zero (current), which would require that
the sum of the ramp compensation signal and current signal
be 4.0 volts. This must be evaluated under full load and low
line conditions.
Ramp Compensation:
Equation 3)
Vrefpwm + Vinst ) VRCOMP
Where: Vrefpwm = 3.8 V
3.8 + (ipk * RS * 16 )
RRC +
t
102, 400
) * on
T
RRC
t
102, 400
* on
T
(3.8 * (16 * ipk * RS))
Where:
RS = Shunt resistance (W)
L = Inductance (H)
Vout = Output voltage (V)
RRC = Ramp comp resistor (kW)
Equation 1)
VRCOMP +
1.6 * Voscpk * 16 k
Current Shunt:
Equation 4)
Combining equations 2 and 3:
RRC
Where: Voscpk = 4.0 V
VRCOMP +
1.6 * 4 * 16 k
102, 400
+
RRC
RRC
RS +
For proper ramp compensation, the ramp signal should
match the falling di/dt (which has been converted to a dv/dt)
of the inductor at 50% duty cycle. 50% duty cycle will occur
when the input voltage is 50% of the output voltage. Thus the
following equations must be satisfied:
RS +
di * T * R * High Frequency Current Gain
S
dt
Vo * T * RS * 16
102, 400
+
RRC
L * 2
RS = Shunt resistance (W)
PO = Output power (W)
L = Inductance (H)
Ǔ
Ǹ2 · Vin
LL
Vout
L
Ǔ ) ǒ16 * ipkǓ
Current Scaling Resistor and Filter Capacitor
R10 sets the gain of the averaged current signal out of the
current sense amplifier. This signal is fed into the AC error
amplifier and is also used in the power multiplier. R10 is used
to scale the current to the appropriate level for protection
purposes in the AC error amplifier circuit. The power
multiplier has an external resistor, R9 that will adjust the gain
of that circuit.
R10 should be calculated to limit the maximum current
signal at the input to the AC error amplifier to less than
4.5 volts at low line and full load. 4.5 volts is the clamp
voltage at the output of the reference amplifier and limits the
maximum averaged current that the unit can process. The
equation for R10 is:
12800 * L
RS +
Vo * T * RRC
ǒ
ǒ
3.8
8 * Vo * ton
Solve for RS and then RRC, using the above equations. It
should be understood that these equations do not take into
account tolerances of the inductor, switching frequency, etc…
The shunt should be a non−wirewound (low inductance)
type of resistor. There are several types of metal film
resistors available for shunt applications.
Equation 2)
ton + T 1 *
(3.8 * 16 * ipk * RS)
12800 * L
* T *
t
Vo * T * RRC
102, 400
on
Where: ton = Switch on time (s)
T = Period (s)
VinLL = Low line input voltage (Vrms)
Vout = DC output voltage (V)
R10 +
Ǹ2 @ P
in VinLL @ ton
ipk +
)
Ǹ2 @ L
VinLL
318, 200 · Pin · RSńVinLL
4.5 * (1.06 · VinLL · ACratio)
Where:
Pin = rated input power (w)
RS = Shunt resistance (W)
VinLL = min. operating rms input voltage (v)
ACratio = AC attenuation factor at pin 5
www.onsemi.com
25
NCP1650
Reference Multiplier
The output of the reference multiplier is a pulse width
modulated representation of the analog input. The multiplier
is internally loaded with a resistor to ground which will set
the DC gain. An external capacitor is required to filter the
signal back into one that resembles the input fullwave
rectified sinewave. The pole for this circuit should be greater
than the line frequency and lower than the switching
frequency.
1/15th of the switching frequency is a recommended
starting value for a 60 Hz line frequency. The filter capacitor
for pin 4 can be determined by the following equation:
This equation does not allow for tolerances, and it would
be advisable to increase the input power to assure operation
at maximum power over production tolerance variations.
The current sense filter capacitor should be selected to set
it’s pole about a factor of 10 below the switching frequency.
C11 + 10.6
f
Where:
C11 = Pin 11 capacitance (nF)
f = pole frequency (kHz)
so, for a 100 kHz switching frequency, a 10 kHz pole is
desirable, and C11 would be 1.0 nF.
C4 +
Maximum Power Circuit
The power multiplier multiplies the input voltage, current
and a scale factor, to output a value that is proportional to the
input power. This voltage is filtered to remove the line
frequency components. The resulting output is compared to
the 2.5 volt reference on the power error amplifier. When the
output of the multiplier reaches 2.5 volts the power loop
takes control and will reduce the output voltage as necessary,
but can not reduce it to less than the peak of the line voltage.
For proper operation, resistor R9 should be chosen such
that the unit will power limit at a value slightly greater than
the maximum power desired. R9 can be calculated by the
formula:
R9 +
C4 = Pin 4 capacitance (F)
fpole = Ref gain pole freq (Hz)
AC Error Amplifier
The AC error amplifier is a transconductance amplifier
that is terminated with a series RC impedance. This creates
a pole−zero pair.
To determine the values of R3 and C3, it is necessary to
look at the two signals that reach the PWM inputs. The
non−inverting input is a slow loop using the averaged
current signal. It’s gain is:
Alf +
V9 R10
ACratio Pin RS 3.75
15 k 15 k
@
@ (gm @ R3) @ 2.3
1 k R10
Where the first two terms are the gains in the current sense
amplifier averaging circuit. The next term is the gain of the
transconductance amplifier and the constant is the gain of
the AC Reference Buffer.
The high frequency path is that of the instantaneous
current signal to the PWM non−inverting input. This gain is
simply 16, since the input signal is converted to a current
through a 1 k resistor, and then terminated by the 16 k
resistor at the PWM input.
For stability, the gain of the low frequency path must be
less than the gain of the high frequency path. This can be
written as:
Where:
V9 = Power reference voltage (2.5 v nom)
R10 = Current scaling resistor (W)
ACratio = AC attenuation factor at pin 5
Pin = rated input power (w)
RS = Shunt resistance (W)
The NCP1650 has been designed such that with a 2%
current shunt and a 1% AC divider, the RSS error will be 7%
maximum, or a worst case error of 14%. In order to assure
maximum power output the reference voltage (V9) should
be reduced by the error factor.
The output signal from the power multiplier should be
close to a DC level, so a filter cap needs to be added with a
high frequency pole relative to the line frequency. For a
60 Hz line, a 0.6 Hz pole would allow 40 dB of attenuation,
or .01 which would reduce a 5.0 volt p−p signal to a DC level
of 2.5 volts, with 50 mv of ripple. The chosen frequency will
be a tradeoff of response time vs. ripple. For a pole of 0.6 Hz:
C9 +
1
+ 6.366E * 6
fpole
2 @ p @ 25 k @ fpole
517, 500 @ gm @ R3
R10
t 16
The suggested resistor and capacitor values are:
R3 +
R10
56, 000 gm
and for a zero at 1/10th of the switching frequency
C3 + 1.59
fsw R3
1
+ 0.265
2 @ p @ R9 @ 0.6
R9
Where:
Where:
C9 = Pin 9 capacitance (F)
R3 and R10 are in units of W
gm is in units of mhos
C3 is in Farads
fsw is in Hz
R9 = Pin 9 resistance (W)
www.onsemi.com
26
NCP1650
Loop Compensation
Rac2
Rac1
Vac
Vline
Vo
Rdc1
V′
FB/SD
+
-
6
4V
Rdc2
Ve/a
ORing NET
−0.32 mA/V
REFERENCE
MULTIPLIER
AC
ERROR
AMP
Vref
RL
4V
OUT
-
-
LOGIC
+
+
ERROR
AMP
C
Q1
16
PWM
25 k
RS
12
C.S. Amp
LOOP COMP
7
Iavg
IS−
RECTIFIER
10
R10
R7
C7
DIVIDER
Rdc2
VȀ +
Vo
Rdc1 ) Rdc2
ERROR AMP
Gm
funity +
2pC
REFERENCE SIGNAL
7
1
fz +
2 p C7 R7
MODULATOR AND OUTPUT STAGE
RL R10
DVo
+
DVref
225k RS
Vref
+ −2 Vac
Veńa
Vac +
Vline Rac2
1
fp +
2pRC
Rac1 ) Rac2
Av + G m R 7
(High Frequency Gain, Past Zero)
Figure 41. Voltage Loop Model
Voltage Loop
Block Diagram
20
GAIN (dB)
The block diagram for the voltage loop has been broken down
into four sections. These are the voltage divider, voltage error
amplifier, reference signal and modulator and output stage.
The modulator and output stage circuitry is greatly
simplified based on the assumption that that poles and zeros
in the current feedback loop are considerably greater than
the bandwidth of the overall loop. This should be a good
assumption, because a bandwidth in the kilohertz is
necessary for a good current waveform, and the voltage error
amplifier needs to have a bandwidth of less than the lowest
line frequency that will be used.
There are two poles in this circuit. The output filter has a
pole that varies with the load. The pole on the voltage error
amplifier will be determined by this analysis.
0
UNITY GAIN
Av
−20
FREQUENCY
Figure 42. Pole−Zero Bode Plot
Reference Signal
The voltage divider is a simple resistive divider that
reduces the output voltage to the 4.0 volt level required by
the internal reference on the voltage error amplifier.
The output of the error amplifier is modified by the ORing
network, which has a negative gain, and is then used as an
input to the reference multiplier. The gain of this block is
dependent on the AC input voltage, because of the multiplier
which requires two inputs for one output.
Voltage Error Amplifier
Modulator and Output Stage
The voltage error amplifier is constrained by the three
equations. When this amplifier is compensated with a
pole−zero pair, there will be a unity gain pole which will be
cancelled by the zero at frequency fZ. The corresponding
bode plot would be:
The AC error amplifier receives an input from the
reference multiplier and forces the current to follow the
shape and amplitude of the reference signal. The current
shaping circuit is an internal loop within this section due to
the current sense amplifier. Based on the assumptions listed
Voltage Divider
www.onsemi.com
27
NCP1650
Plot the sum of these three values. Figure 43 shows a gain
of 35.5 dB until the pole of the output filter is reached at
0.3 Hz. After that, the gain is reduced at a rate of
20 dB/decade.
in the introduction to this analysis, this is not analyzed
separately.
The equation for the gain is good for frequencies below
the pole. There is a single pole due to the output filter. Since
the NCP1650 is a current mode converter, the inductor is not
part of the output pole as can be seen in that equation.
40
LOOP GAIN
WITHOUT
ERROR AMP
30
Calculating the Loop Gain
At this point in the design process, all of the parameters
involved in this calculation have been determined with the
exception of the pole−zero pair on the output of the voltage
error amplifier.
All equations give gains in absolute numbers. It is
necessary to convert these to the decibel format using the
following formula:
GAIN (dB)
20
10
0
−10
−20
A(dB) + 20 Log10 (A)
−30
For example, the voltage divider would be:
−40
0.01
5.6 k
A+
+ .0099
560 k ) 5.6 k
0.1
1
10
FREQUENCY (Hz)
100
1000
Figure 43. Open Loop Gain Less Error Amp
A(dB) + 20 Log10 .0099 + * 40 dB
The gain of the loop will vary as the input voltage changes.
It is recommended that the compensation for the voltage
error amplifier be calculated under high line, full load
conditions. This should be the greatest bandwidth that the
unit will see.
By necessity, the unity gain (OdB) loop bandwidth for a
PFC unit, must be less than the line frequency. If the
bandwidth approaches or exceeds the line frequency, the
voltage error amplifier signal will have frequency
components in its output that are greater than the line
frequency. These components will cause distortion in the
output of the reference amplifier, which is used to shape the
current waveform. This in turn will cause distortion in the
current and reduce the power factor.
Typically the maximum bandwidth for a 60 Hz PFC
converter is 10 Hz, and slightly less for a 50 Hz system. This
can be adjusted to meet the particular requirements of a
system. The unity gain bandwidth is determined by the
frequency at which the loop gain passes through the 0 dB
level.
For stability purposes, the gain should pass through 0 dB
with a slope of –20 dB/decade for approximately one decade
on either side of the unity gain frequency. This assures a
phase margin of greater than 45°.
The gain can be calculated graphically using the equations
of Figure 43 as follows:
Divider: Calculate V’/Vo in dB, this value is constant so
it will not change with frequency.
Reference Signal: Calculate Vref/Ve/a using the peak level
of the AC input signal at high line that will be seen on pin 5.
Convert this to dB. This is also a constant value.
Modulator and Output Stage: Calculate the gain in dB for
DVo/DVref. Calculate the pole frequency. The gain will be
constant for all frequencies less than fp. Starting at the pole
frequency, this gain will drop off at a rate of 20 dB/decade.
A typical error amplifier bode plot is shown in Figure 44.
The zero is used to offset the pole of the output filter. The
output filter pole will typically be lower than the unity gain
loop bandwidth, so the zero will be necessary.
This plot shows a forward gain of 7.0 dB at 10 Hz. To
compensate for this the error amplifier should have a gain of
–7.0 dB (0.45) at 10 Hz, and a zero at 0.4 Hz. The gain at
10 Hz is determined by the resistor since it is well past the
zero. The resistor can be calculated by the equation:
R7 + AvńGm + .45ń.0001 + 4.5 kW
4.7 kW is the closest standard value. Using this, the
capacitor can be calculated based on the zero frequency of
0.4 Hz. This would give a value for C7 of:
C+
1
+ 85 mF
2 @ p @ 4.7 k @ 0.4 Hz
Using these values (4.7 kW and 86 mF), the open loop gain
plot would be:
80
VOLTAGE
LOOP BODE
PLOT
60
GAIN (dB)
40
20
0
−20
−40
0.01
0.1
1
10
FREQUENCY (Hz)
100
Figure 44. Open Loop Gain of Voltage Loop
www.onsemi.com
28
1000
NCP1650
Vline
Rac1
AC INPUT
Vac
5
Rac2
POWER
MULTIPLIER
Vpm
Pmax
+
-
9
2.5 V
R9
Vpa
ORing NET
−0.32 mA/V
REFERENCE
MULTIPLIER
Vref
AC
ERROR
AMP
+
POWER
AMP
Q1
4V
OUT
-
LOGIC
+
16
PWM
25 k
C9
12
C.S. Amp
IS−
IO
LOOP COMP
Iavg
8
10
R10
R8
RS
C8
POWER MULTIPLIER
Vpm
io
+
Vac +
3.75 R9 Vac RS
R10
Vline Rac2
Rac1 ) Rac2
1
fp +
2 p C9 R9
POWER AMP
Av +
REFERENCE SIGNAL
MODULATOR AND OUTPUT STAGE
Vref
+ −2 Vac
Vpa
Gm
2 p f C8
1
fz +
2 p C8 R8
Vac +
io
R10
+
Vref
225k RS
Vline Rac2
Rac1 ) Rac2
Av + G m R 8
(High Frequency Gain, Past Zero)
Figure 45. Power Loop Model
Power Loop
Power Multiplier
The power multiplier’s gain is a function of the input
voltage. This multiplier has a very low frequency pole that
must be considerably lower than the line frequency, so that
the power signal is essentially a DC level.
Block Diagram
The block diagram for the power loop has been broken
down into four sections. These are the power multiplier,
power amplifier, reference signal and modulator and output
stage.
Similar to the voltage loop, the modulator and output stage
circuitry has been greatly simplified due to the location of
the associated poles and zeros.
There are two significant poles in this circuit. The first is
on the power multiplier and the second is due to the power
error amplifier. Because the pole on the power multiplier is
very low, it will normally be necessary to include the resistor
(R8) for the zero on this amplifier.
Reference Signal
The reference signal block is unchanged from the voltage
loop model.
Modulator and Output Stage
For the power circuit, the transfer function of the
modulator and output circuitry follows the path from the AC
reference voltage (Vref) to the output current. Since this
circuit regulates the power, and the input and output voltages
are the two basic components of the power, the output
current is the output variable for this block.
There is no pole associated with this function.
www.onsemi.com
29
NCP1650
Power Amplifier
For this example it can be seen that for a bandwidth of
1.0 Hz, the power amplifier needs a gain of –27 dB
(0.045 v/v) at 1.0 Hz, with a zero at 0.7 Hz. The zero
frequency is chosen to match the pole frequency. Although
it is not essential to do this, it is a safe method of assuring a
stable system.
Since the frequency that we are interested in is greater than
the zero frequency, the gain of the amplifier is:
The compensation for this amplifier will be determined
similar to the network for the voltage error amplifier. The
series RC on pin 8 will create a pole−zero pair based on the
equations given.
Calculating the Loop Gain
The power loop gain should be calculated using high line
conditions. At lower lines the bandwidth will decrease.
Similar to the voltage loop, calculate the gains and power
multiplier pole. Make sure that they are converted to dB’s.
Begin with all stages except the power amplifier, and
determine what the gain of the power amplifier needs to be
at the unity gain frequency. This loop is normally slower
than the voltage loop and will generally be a factor of 5 to 10
lower in bandwidth.
The loop gain without the amplifier should resemble the
following plot:
Av + G m R 8
or, R8 + AvńGm + 0.045ń.0001 + 446 Ohms
a 470 Ohm resistor would be a good choice, and for a zero
at 0.7 Hz:
C8 +
and a 470 mF cap would be a good choice. Using these two
values, the resulting open loop plot would be:
30
60
POWER LOOP
GAIN LESS
POWER AMP
20
40
20
GAIN (dB)
10
GAIN (dB)
1
+ 483 mF
2 @ p @ 470 W @ 0.7 Hz
0
−10
0
−20
−20
−40
−30
−60
−40
0.01
0.1
1
10
FREQUENCY (Hz)
100
−80
1000
0.01
Figure 46. Power Loop without Power Amp
0.1
1
10
FREQUENCY (Hz)
100
1000
Figure 47. Power Circuit Open Loop Gain
As stated previously, these are calculated values, and may
require adjustment in actual circuit conditions.
www.onsemi.com
30
NCP1650
PACKAGE DIMENSIONS
SOIC−16
CASE 751B−05
ISSUE K
−A−
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
9
−B−
1
P
8 PL
0.25 (0.010)
8
B
M
S
DIM
A
B
C
D
F
G
J
K
M
P
R
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT*
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
31
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP1650/D