T2322B Sensitive Gate Triacs Silicon Bidirectional Thyristors Designed primarily for ac power switching. The gate sensitivity of these triacs permits the use of economical transistorized or integrated circuit control circuits, and it enhances their use in low-power phase control and load-switching applications. http://onsemi.com TRIACS 2.5 AMPERES RMS 200 VOLTS Features • • • • • Very High Gate Sensitivity Low On-State Voltage at High Current Levels Glass-Passivated Chip for Stability Small, Rugged Thermopad Construction for Low Thermal Resistance, High Heat Dissipation and Durability Pb−Free Package is Available* MT2 MT1 G MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating Symbol Value Unit Peak Repetitive Off-State Voltage (Note 1) (TJ = 25 to 110°C, Gate Open) VDRM, VRRM 200 V On-State RMS Current (TC = 70°C) (Full Cycle Sine Wave 50 to 60 Hz) IT(RMS) 2.5 A Peak Non−Repetitive Surge Current (One Full Cycle, Sine Wave 60 Hz, TC = 70°C) ITSM 25 A Circuit Fusing Consideration (t = 8.3 ms) I2t 2.6 A2s PGM 10 W PG(AV) 0.5 W Peak Gate Current (Pulse Width = 10 ms, TC = 70°C) IGM 0.5 A Operating Junction Temperature Range TJ −40 to +110 °C Storage Temperature Range Tstg −40 to +150 °C − 8.0 in. lb. 3 Peak Gate Power (Pulse Width ≤ 10 ms, TC = 70°C) Average Gate Power (t = 8.3 ms, TC = 70°C) Mounting Torque (6-32 Screw) (Note 2) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. VDRM and VRRM for all types can be applied on a continuous basis. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. 2. Torque rating applies with use of torque washer (Shakeproof WD19523 or equivalent). Mounting Torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Main terminal 2 and heat-sink contact pad are common. TO−225AA (formerly TO−126) CASE 077 STYLE 5 2 1 MARKING DIAGRAM YWW T 2322BG Y WW T2322B G = Year = Work Week = Device Code = Pb−Free Package PIN ASSIGNMENT 1 Main Terminal 1 2 Main Terminal 2 3 Gate ORDERING INFORMATION Device *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2006 May, 2006 − Rev. 5 1 Package Shipping T2322B TO225AA 500 Units/Box T2322BG TO225AA (Pb−Free) 500 Units/Box Publication Order Number: T2322/D T2322B THERMAL CHARACTERISTICS Symbol Max Unit Thermal Resistance, Junction−to−Case Characteristic RqJC 3.5 °C/W Thermal Resistance, Junction−to−Ambient RqJA 60 °C/W TL 260 °C Maximum Lead Temperature for Soldering Purposes 1/8″ from Case for 10 Sec ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit − − − 0.2 10 0.75 mA mA OFF CHARACTERISTICS Peak Repetitive Blocking Current (VD = Rated VDRM, VRRM; Gate Open) TJ = 25°C TJ = 110°C IDRM, IRRM ON CHARACTERISTICS Peak On-State Voltage (Note 3) (ITM = "10 A) VTM − 1.7 2.2 V Gate Trigger Current (Continuous dc) (VD = 12 V, RL = 100 W) All Quadrants IGT − − 10 mA Gate Trigger Voltage (Continuous dc) (VD = 12 Vdc, RL = 100 W, TC = 25°C) VGT − 1.0 2.2 V Gate Non−Trigger Voltage (VD = 12 V, RL = 100 W, TC = 110°C) VGD 0.15 − − V Holding Current (VD = 12 V, IT (Initiating Current) = "200 mA, Gate Open) IH − 15 30 mA Gate Controlled Turn-On Time (VD = Rated VDRM, ITM = 10 A pk, IG = 60 mA, tr = 0.1 msec) tgt − 1.8 2.5 ms dv/dt 10 100 − V/ms dv/dt(c) 1.0 4.0 − V/ms DYNAMIC CHARACTERISTICS Critical Rate-of-Rise of Off-State Voltage (VD = Rated VDRM, Exponential Waveform, TC = 100°C) Critical Rate-of-Rise of Commutation Voltage (VD = Rated VDRM, ITM = 3.5 A pk, Commutating di/dt = 1.26 A/ms, Gate Unenergized, TC = 90°C) 3. Pulse Test: Pulse Width ≤ 1.0 ms, Duty Cycle ≤ 2%. http://onsemi.com 2 T2322B Voltage Current Characteristic of Triacs (Bidirectional Device) + Current Symbol Parameter VDRM Peak Repetitive Forward Off State Voltage IDRM Peak Forward Blocking Current VRRM Peak Repetitive Reverse Off State Voltage IRRM Peak Reverse Blocking Current VTM Maximum On State Voltage IH Holding Current VTM on state IH IRRM at VRRM off state IH Quadrant 3 MainTerminal 2 − VTM Quadrant Definitions for a Triac MT2 POSITIVE (Positive Half Cycle) + (+) MT2 Quadrant II (+) MT2 Quadrant I (+) IGT GATE (−) IGT GATE MT1 MT1 REF REF IGT − + IGT (−) MT2 Quadrant III Quadrant 1 MainTerminal 2 + (−) MT2 Quadrant IV (+) IGT GATE (−) IGT GATE MT1 MT1 REF REF − MT2 NEGATIVE (Negative Half Cycle) All polarities are referenced to MT1. With in−phase signals (using standard AC lines) quadrants I and III are used. http://onsemi.com 3 + Voltage IDRM at VDRM T2322B PACKAGE DIMENSIONS TO−225 CASE 77−09 ISSUE Z −B− U F Q −A− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 077−01 THRU −08 OBSOLETE, NEW STANDARD 077−09. C M 1 2 3 H DIM A B C D F G H J K M Q R S U V K J V G S R 0.25 (0.010) A M M B M D 2 PL 0.25 (0.010) M A M B M INCHES MIN MAX 0.425 0.435 0.295 0.305 0.095 0.105 0.020 0.026 0.115 0.130 0.094 BSC 0.050 0.095 0.015 0.025 0.575 0.655 5 _ TYP 0.148 0.158 0.045 0.065 0.025 0.035 0.145 0.155 0.040 −−− MILLIMETERS MIN MAX 10.80 11.04 7.50 7.74 2.42 2.66 0.51 0.66 2.93 3.30 2.39 BSC 1.27 2.41 0.39 0.63 14.61 16.63 5 _ TYP 3.76 4.01 1.15 1.65 0.64 0.88 3.69 3.93 1.02 −−− STYLE 5: PIN 1. MT 1 2. MT 2 3. GATE ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 4 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative T2322/D