EMI5204MU D

EMI5204MU, EMI5206MU,
EMI5208MU
Four-Six-Eight-Channel EMI
Filter with Integrated ESD
Protection
The EMI520xMU Series are a 4, 6, 8−channel (C−R−C) Pi−style
EMI filter array with integrated ESD protection. Its typical component
values of R = 100 and C = 7 pF deliver a cutoff frequency of 250
MHz and stop band attenuation greater than 20 dB from 800 MHz to
5.0 GHz.
This performance makes the part ideal for parallel interfaces with
data rates up to 167 Mbps in applications where wireless interference
must be minimized. The specified attenuation range is very effective
in minimizing interference from 2G/3G, GPS, Bluetooth® and
WLAN signals.
The EMI520xMU Series is available in the low−profile 4, 6, 8−lead,
0.5mm thick UDFN packages with 0.4mm lead pitch.
http://onsemi.com
MARKING
DIAGRAMS
8
1
12
1
• ±8.0 kV ESD Protection on each channel (IEC61000−4−2 Level 4,
1
XX
M
G
Contact Discharge)
• R/C Values of 100 and 7 pF deliver Exceptional S21 Performance
•
Characteristics of 250 MHz f3dB and 20 dB Stop Band Attenuation
from 800 MHz to 5.0 GHz
Integrated EMI/ESD System Solution in UDFN Package Offers
Exceptional Cost, System Reliability and Space Savings
This is a Pb−Free Device
54 MG
G
1
56 MG
G
UDFN12
CASE 517BD
1
16
Features/Benefits
•
UDFN8
CASE 517BC
UDFN16
CASE 517BE
58 MG
G
1
= Specific Device Code
= Date Code
= Pb−Free Package
(*Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
Applications
• EMI Filtering for LCD and Camera Data Lines
• EMI Filtering and Protection for I/O Ports and Keypads
0
−5
R=100 Filter + ESDn
Cd = 7 pF
Cd = 7 pF
Filter + ESDn
S21 (dB)
−10
−15
−20
−25
−30
See Table 1 for pin description
−35
−40
1E+6
10E+6
100E+6
1E+9
10E+9
FREQUENCY (Hz)
Figure 1. Electrical Schematic
© Semiconductor Components Industries, LLC, 2011
July, 2011 − Rev. 0
Figure 2. Typical Insertion Loss Curve
1
Publication Order Number:
EMI5204MU/D
EMI5204MU, EMI5206MU, EMI5208MU
1 2 3 4
1 2 3 4 5 6
1 2 3 4 5 6 7 8
GND
GND
GND
8 7 6 5
EMI5204MU
12 1110 9 8 7
EMI5206MU
1615141312 11 10 9
EMI5208MU
Figure 3. Pin Diagram
(Bottom View)
Table 1. FUNCTIONAL PIN DESCRIPTION
Filter
Device Pins
Description
EMI5204MU
EMI5206MU
EMI5208MU
Filter 1
1&8
1 & 12
1 & 16
Filter + ESD Channel 1
Filter 2
2&7
2 & 11
2 & 15
Filter + ESD Channel 2
Filter 3
3&6
3 & 10
3 & 14
Filter + ESD Channel 3
Filter 4
4&5
4&9
4 & 13
Filter + ESD Channel 4
Filter 5
5&8
5 & 12
Filter + ESD Channel 5
Filter 6
6&7
6 & 11
Filter + ESD Channel 6
Filter 7
7 & 10
Filter + ESD Channel 7
Filter 8
8&9
Filter + ESD Channel 8
GND
Ground
Ground Pad
GND
GND
MAXIMUM RATINGS
Parameter
ESD Discharge IEC61000−4−2
Symbol
Value
Unit
VPP
8.0
kV
Contact Discharge
Operating Temperature Range
TOP
−40 to 85
°C
Storage Temperature Range
TSTG
−55 to 150
°C
TL
260
°C
Maximum Lead Temperature for Soldering Purposes (1.8 in from case for 10 seconds)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted)
Parameter
Maximum Reverse Working Voltage
Breakdown Voltage
Symbol
Test Conditions
Min
Typ
VRWM
5.0
V
8.0
V
100
nA
115
IR = 1.0 mA
Leakage Current
IR
VRWM = 3.3 V
Resistance
RA
IR = 10 mA
Diode Capacitance
Cd
VR = 2.5 V, f = 1.0 MHz
7.0
11
pF
Line Capacitance
CL
VR = 2.5 V, f = 1.0 MHz
14
22
pF
3 dB Cut−Off Frequency (Note 1)
f3dB
Above this frequency,
appreciable attenuation occurs
250
http://onsemi.com
2
85
7.0
Unit
VBR
1. 50 source and 50 load termination.
6.0
Max
100
MHz
EMI5204MU, EMI5206MU, EMI5208MU
Theory of Operation
From this it can be seen that a square wave consists of odd
order harmonics and to fully construct a square wave n must
go to infinity. However, to retain an acceptable portion of the
waveform, the first two terms are generally sufficient. These
two terms contain about 85% of the signal amplitude and
allow a reasonable square wave to be reconstructed.
Therefore, to reasonably pass a square wave of frequency x
the minimum filter bandwidth necessary is 3x. All
ON Semiconductor EMI filters are rated according to this
principle. Attempting to violate this principle will result in
significant rounding of the waveform and cause problems in
transmitting the correct data. For example, take the filter
with the response shown in Figure 4 and apply three
different data waveforms. To calculate these three different
frequencies, the 3 dB, 6 dB, and 9 dB bandwidths will be
used.
The EMI520x combines ESD protection and EMI
filtering conveniently into a small package for today’s size
constrained applications. The capacitance inherent to a
typical protection diode is utilized to provide the
capacitance value necessary to create the desired frequency
response based upon the series resistance in the filter. By
combining this functionality into one device, a large number
of discrete components are integrated into one small
package saving valuable board space and reducing BOM
count and cost in the application.
Application Example
The accepted practice for specifying bandwidth in a filter
is to use the 3 dB cutoff frequency. Utilizing points such as
the 6 dB or 9 dB cutoff frequencies results in signal
degradation in an application. This can be illustrated in an
application example. A typical application would include
EMI filtering of data lines in a camera or display interface.
In such an example it is important to first understand the
signal and its spectral content. By understanding these
things, an appropriate filter can be selected for the desired
application. A typical data signal is pattern of 1’s and 0’s
transmitted over a line in a form similar to a square wave.
The maximum frequency of such a signal would be the
pattern 1−0−1−0 such that for a signal with a data rate of
100 Mbps, the maximum frequency component would be
50 MHz. The next item to consider is the spectral content of
the signal, which can be understood with the Fourier series
approximation of a square wave, shown below in
Equations 1 and 2 in the Fourier series approximation.
Equation 1:
x(t) +
a
1 2
1
)
sinǒ(2n * 1) 0tǓ
2 n + 1 2n * 1
ƪ
ƫ
(eq. 1)
Equation 2 (Simplified form of Equation 1):
x(t) +
1
)
2
ǒ Ǔ
2 sin 0t
ƪ
1
(eq. 2)
) p20
sinǒ3 0tǓ
3
) p20
sinǒ5 0tǓ
5
)AAA
ƫ
−3 dB
MAGNITUDE
(dB)
−6 dB
−9 dB
f1
100k
1M
10M
f2
f3
100M
1G
10G
FREQUENCY
(Hz)
Figure 4. Filter Bandwidth
multiply the result by two). The following table gives the
bandwidth values and the corresponding maximum
supported frequencies and the third harmonic frequencies.
From the above paragraphs it is shown that the maximum
supported frequency of a waveform that can be passed
through the filter can be found by dividing the bandwidth by
a factor of three (to obtain the corresponding data rate
http://onsemi.com
3
EMI5204MU, EMI5206MU, EMI5208MU
the third harmonic term is significantly attenuated. This
serves to round the signal edges and skew the waveform, as
is shown in Figure 5b. In the case that a 100 MHz signal is
input to this filter, the third harmonic term is attenuated even
further and results in even more rounding of the signal edges
as is shown in Figure 5c. The result is the degradation of the
data being transmitted making the digital data (1’s and 0’s)
more difficult to discern. This does not include effects of
other components such as interconnect and other path losses
which could further serve to degrade the signal integrity.
While some filter products may specify the 6 dB or 9 dB
bandwidths, actually using these to calculate supported
frequencies (and corresponding data rates) results in
significant signal degradation. To ensure the best signal
integrity possible, it is best to use the 3 dB bandwidth to
calculate the achievable data rate.
Table 2. FREQUENCY CHART
Bandwidth
Maximum
Supported
Frequency
Third
Harmonic
Frequency
3 dB − 100 MHz
33.33 MHz (f1)
100 MHz
6 dB − 200 MHz
66.67 MHz (f2)
200 MHz
9 dB − 300 MHz
100 MHz (f3)
300 MHz
Considering that 85% of the amplitude of the square is in
the first two terms of the Fourier series approximation most
of the signal content is at the fundamental (maximum
supported) frequency and the third harmonic frequency. If a
signal with a frequency of 33.33 MHz is input to this filter,
the first two terms are sufficiently passed such that the signal
is only mildly affected, as is shown in Figure 5a. If a signal
with a frequency of 66.67 MHz is input to this same filter,
Input Waveform
Output Waveform
a) Frequency = f1
Input Waveform
b) Frequency = f2
Input Waveform
Output Waveform
Output Waveform
c) Frequency = f3
Figure 5. Input and Output Waveforms of Filter
ORDERING INFORMATION
Package
Shipping†
EMI5204MUTAG
UDFN8
(Pb−Free)
3000 / Tape & Reel
EMI5206MUTAG
UDFN12
(Pb−Free)
3000 / Tape & Reel
EMI5208MUTAG
UDFN16
(Pb−Free)
3000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
4
EMI5204MU, EMI5206MU, EMI5208MU
PACKAGE DIMENSIONS
UDFN8, 1.7x1.35, 0.4P
CASE 517BC−01
ISSUE O
A
B
D
2X
0.10 C
PIN ONE
REFERENCE
2X
ÉÉÉ
ÉÉÉ
ÇÇ
ÇÇ
ÉÉ
MOLD CMPD
EXPOSED Cu
A1
E
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.25 mm FROM THE TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
A3
DETAIL B
ALTERNATE
CONSTRUCTIONS
0.10 C
TOP VIEW
A
DETAIL B
0.05 C
8X
L
L1
DETAIL A
0.05 C
NOTE 4
SIDE VIEW
DETAIL A
8X
L
(A3)
L
A1
C
SEATING
PLANE
ALTERNATE TERMINAL
CONSTRUCTIONS
MILLIMETERS
MIN
MAX
0.45
0.55
0.00
0.05
0.13 REF
0.15
0.25
1.70 BSC
1.10
1.30
1.35 BSC
0.30
0.50
0.40 BSC
0.15
−−−
0.20
0.30
−−−
0.05
RECOMMENDED
SOLDERING FOOTPRINT*
D2
1
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
E2
1.40
8X
0.40
8X
8
K
e
e/2
PACKAGE
OUTLINE
8X b
0.10 C A B
0.05 C
NOTE 3
1.55
BOTTOM VIEW
0.50
8X
0.25
1
0.40 PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
5
EMI5204MU, EMI5206MU, EMI5208MU
PACKAGE DIMENSIONS
UDFN12, 2.5x1.35, 0.4P
CASE 517BD−01
ISSUE O
A
B
D
2X
0.10 C
PIN ONE
REFERENCE
2X
ÉÉÉ
ÉÉÉ
0.10 C
L1
DETAIL A
E
OPTIONAL
CONSTRUCTIONS
TOP VIEW
EXPOSED Cu
A
DETAIL B
(A3)
0.05 C
12X
A1
0.05 C
NOTE 4
12X
A1
SIDE VIEW
6
1
C
SEATING
PLANE
ÇÇ
ÉÉ
ÉÉ
MOLD CMPD
A3
DETAIL B
OPTIONAL
CONSTRUCTION
DETAIL A
D2
L
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.25 mm FROM THE TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
L
L
12
7
e
E2
BOTTOM VIEW
12X
MILLIMETERS
MIN
MAX
0.45
0.55
0.00
0.05
0.13 REF
0.15
0.25
2.50 BSC
1.90
2.10
1.35 BSC
0.30
0.50
0.40 BSC
0.15
−−−
0.20
0.30
−−−
0.05
RECOMMENDED
SOLDERING FOOTPRINT*
PACKAGE
OUTLINE
K
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
2.20
12X
0.40
b
0.10 C A B
0.05 C
1.55
NOTE 3
0.50
12X
0.40
PITCH
0.25
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
6
EMI5204MU, EMI5206MU, EMI5208MU
PACKAGE DIMENSIONS
UDFN16, 3.3x1.35, 0.4P
CASE 517BE−01
ISSUE O
A
B
D
2X
0.10 C
PIN ONE
REFERENCE
2X
0.10 C
ÉÉÉ
ÉÉÉ
L1
DETAIL A
E
OPTIONAL
CONSTRUCTIONS
TOP VIEW
EXPOSED Cu
A
DETAIL B
0.05 C
(A3)
16X
A1
0.05 C
NOTE 4
16X
A1
SIDE VIEW
8
1
C
SEATING
PLANE
ÇÇ
ÉÉ
16
9
e
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
MOLD CMPD
A3
OPTIONAL
CONSTRUCTION
E2
16X
MILLIMETERS
MIN
MAX
0.45
0.55
0.00
0.05
0.13 REF
0.15
0.25
3.30 BSC
2.70
2.90
1.35 BSC
0.30
0.50
0.40 BSC
0.15
−−−
0.20
0.30
−−−
0.05
RECOMMENDED
SOLDERING FOOTPRINT*
PACKAGE
OUTLINE
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.25 mm FROM THE TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
DETAIL B
DETAIL A
D2
L
L
L
3.00
16X
0.40
b
BOTTOM VIEW
1.55
0.10 C A B
0.05 C
NOTE 3
0.50
16X
0.40
PITCH
0.25
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
Bluetooth is a registered trademark of Bluetooth SIG.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
7
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
EMI5204MU/D