HA5022 T UCT R OD RODU C P E P T E E OL UT O B S U B S TI T 5 S 4 2 E FA 1 IBL DataHSheet O SS ® P Dual, 125MHz, Video Current Feedback Amplifier with Disable The HA5022 is a dual version of the popular Intersil HA5020. It features wide bandwidth and high slew rate, and is optimized for video applications and gains between 1 and 10. It is a current feedback amplifier and thus yields less bandwidth degradation at high closed loop gains than voltage feedback amplifiers. The low differential gain and phase, 0.1dB gain flatness, and ability to drive two back terminated 75Ω cables, make this amplifier ideal for demanding video applications. The HA5022 also features a disable function that significantly reduces supply current while forcing the output to a true high impedance state. This functionality allows 2:1 video multiplexers to be implemented with a single IC. The current feedback design allows the user to take advantage of the amplifier’s bandwidth dependency on the feedback resistor. By reducing RF , the bandwidth can be increased to compensate for decreases at higher closed loop gains or heavy output loads. PART NUMBER FN3392.7 Features • Dual Version of HA-5020 • Individual Output Enable/Disable • Input Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . .800µV • Wide Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 125MHz • Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475V/µs • Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03% • Differential Phase. . . . . . . . . . . . . . . . . . . . . 0.03 Degrees • Supply Current (per Amplifier) . . . . . . . . . . . . . . . . 7.5mA • ESD Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V • Guaranteed Specifications at ±5V Supplies Applications • Video Multiplexers; Video Switching and Routing • Video Gain Block • Video Distribution Amplifier/RGB Amplifier • Flash A/D Driver Part Number Information TEMP. RANGE (oC) May 2003 • Current to Voltage Converter PACKAGE PKG. NO. • Medical Imaging HA5022IP -40 to 85 16 Ld PDIP E16.3 • Radar and Imaging Systems HA5022IB -40 to 85 16 Ld SOIC M16.15 Pinout HA5022EVAL High Speed Op Amp DIP Evaluation Board 1 HA5022 (PDIP, SOIC) TOP VIEW -IN1 1 +IN1 2 DIS1 - + 16 OUT1 15 NC 3 14 NC V- 4 13 V+ DIS2 5 12 NC +IN2 6 -IN2 7 NC 8 + - 11 NC 10 OUT2 9 NC CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003. All Rights Reserved All other trademarks mentioned are the property of their respective owners. HA5022 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 36V DC Input Voltage (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . ±VSUPPLY Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V Output Current (Note 4) . . . . . . . . . . . . . . . . . Short Circuit Protected ESD Rating (Note 3) Human Body Model (Per MIL-STD-883 Method 3015.7) . . 2000V Thermal Resistance (Typical, Note 2) θJA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . .175oC Maximum Junction Temperature (Plastic Package, Note 1) . .150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC Supply Voltage Range (Typical) . . . . . . . . . . . . . . . . ±4.5V to ±15V CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175oC for die, and below 150oC for plastic packages. See Application Information section for safe operating area information. 2. θJA is measured with the component mounted on an evaluation PC board in free air. 3. The non-inverting input of unused amplifiers must be connected to GND. 4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle) output current should not exceed 15mA for maximum reliability. VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified Electrical Specifications (NOTE 11) TEST LEVEL TEMP. (oC) MIN TYP MAX UNITS A 25 - 0.8 3 mV A Full - - 5 mV Delta VIO Between Channels A Full - 1.2 3.5 mV Average Input Offset Voltage Drift B Full - 5 - µV/oC A 25 53 - - dB A Full 50 - - dB A 25 60 - - dB A Full 55 - - dB A Full ±2.5 - - V A 25 - 3 8 µA A Full - - 20 µA A 25 - - 0.15 µA/V A Full - - 0.5 µA/V A 25 - - 0.1 µA/V A Full - - 0.3 µA/V A 25, 85 - 4 12 µA A -40 - 10 30 µA A 25, 85 - 6 15 µA A -40 - 10 30 µA A 25 - - 0.4 µA/V A Full - - 1.0 µA/V TEST CONDITIONS PARAMETER INPUT CHARACTERISTICS Input Offset Voltage (VIO) VIO Common Mode Rejection Ratio VIO Power Supply Rejection Ratio Input Common Mode Range Note 5 ±3.5V ≤ VS ≤ ±6.5V Note 5 Non-Inverting Input (+IN) Current +IN Common Mode Rejection (+IBCMR = 1 ) +RIN Note 5 +IN Power Supply Rejection ±3.5V ≤ VS ≤ ±6.5V Inverting Input (-IN) Current Delta -IN BIAS Current Between Channels -IN Common Mode Rejection Note 5 2 HA5022 VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified (Continued) Electrical Specifications TEST CONDITIONS PARAMETER ±3.5V ≤ VS ≤ ±6.5V -IN Power Supply Rejection (NOTE 11) TEST LEVEL TEMP. (oC) MIN TYP MAX UNITS A 25 - - 0.2 µA/V A Full - - 0.5 µA/V Input Noise Voltage f = 1kHz B 25 - 4.5 - nV/√Hz +Input Noise Current f = 1kHz B 25 - 2.5 - pA/√Hz -Input Noise Current f = 1kHz B 25 - 25.0 - pA/√Hz Note 16 A 25 1.0 - - MΩ A Full 0.85 - - MΩ A 25 70 - - dB A Full 65 - - dB A 25 50 - - dB A Full 45 - - dB A 25 ±2.5 ±3.0 - V A Full ±2.5 ±3.0 - V TRANSFER CHARACTERISTICS Transimpedance RL = 400Ω, VOUT = ±2.5V Open Loop DC Voltage Gain RL = 100Ω, VOUT = ±2.5V Open Loop DC Voltage Gain OUTPUT CHARACTERISTICS Output Voltage Swing RL = 150Ω Output Current RL = 150Ω B Full ±16.6 ±20.0 - mA Output Current, Short Circuit VIN = ±2.5V, VOUT = 0V A Full ±40 ±60 - mA Output Current, Disabled VOUT = ±2.5V, VIN = 0V, DISABLE = 0V A Full - - 2 µA Output Disable Time Note 12 B 25 - 40 - µs Output Enable Time Note 13 B 25 - 40 - ns Output Capacitance, Disabled Note 14 B 25 - 15 - pF Supply Voltage Range A 25 5 - 15 V Quiescent Supply Current A Full - 7.5 10 mA/Op Amp POWER SUPPLY CHARACTERISTICS Supply Current, Disabled DISABLE = 0V A Full - 5 7.5 mA/Op Amp Disable Pin Input Current DISABLE = 0V A Full - 1.0 1.5 mA Minimum Pin 8 Current to Disable Note 6 A Full 350 - - µA Maximum Pin 8 Current to Enable Note 7 A Full - - 20 µA Slew Rate Note 8 B 25 275 400 - V/µs Full Power Bandwidth Note 9 B 25 22 28 - MHz Rise Time Note 10 B 25 - 6 - ns Fall Time Note 10 B 25 - 6 - ns Propagation Delay Note 10 B 25 - 6 - ns B 25 - 4.5 - % AC CHARACTERISTICS (AV = +1) Overshoot -3dB Bandwidth VOUT = 100mV B 25 - 125 - MHz Settling Time to 1% 2V Output Step B 25 - 50 - ns Settling Time to 0.25% 2V Output Step B 25 - 75 - ns 3 HA5022 VSUPPLY = ±5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified (Continued) Electrical Specifications TEST CONDITIONS PARAMETER (NOTE 11) TEST LEVEL TEMP. (oC) MIN TYP MAX UNITS AC CHARACTERISTICS (AV = +2, RF = 681Ω) Slew Rate Note 8 B 25 - 475 - V/µs Full Power Bandwidth Note 9 B 25 - 26 - MHz Rise Time Note 10 B 25 - 6 - ns Fall Time Note 10 B 25 - 6 - ns Propagation Delay Note 10 B 25 - 6 - ns B 25 - 12 - % Overshoot -3dB Bandwidth VOUT = 100mV B 25 - 95 - MHz Settling Time to 1% 2V Output Step B 25 - 50 - ns Settling Time to 0.25% 2V Output Step B 25 - 100 - ns Gain Flatness 5MHz B 25 - 0.02 - dB 20MHz B 25 - 0.07 - dB AC CHARACTERISTICS (AV = +10, RF = 383Ω) Slew Rate Note 8 B 25 350 475 - V/µs Full Power Bandwidth Note 9 B 25 28 38 - MHz Rise Time Note 10 B 25 - 8 - ns Fall Time Note 10 B 25 - 9 - ns Propagation Delay Note 10 B 25 - 9 - ns B 25 - 1.8 - % Overshoot -3dB Bandwidth VOUT = 100mV B 25 - 65 - MHz Settling Time to 1% 2V Output Step B 25 - 75 - ns Settling Time to 0.1% 2V Output Step B 25 - 130 - ns Differential Gain (Note 15) RL = 150Ω B 25 - 0.03 - % Differential Phase (Note 15) RL = 150Ω B 25 - 0.03 - Degrees VIDEO CHARACTERISTICS NOTES: 5. VCM = ±2.5V. At -40oC Product is tested at VCM = ±2.25V because short test duration does not allow self heating. 6. RL = 100Ω, VIN = 2.5V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is considered disabled when -10mV ≤ VOUT ≤ +10mV. 7. VIN = 0V. This is the maximum current that can be pulled out of the Disable pin with the HA5022 remaining enabled. The HA5022 is considered disabled when the supply current has decreased by at least 0.5mA. 8. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points. Slew Rate9. FPBW = ---------------------------;V = 2V. 2πV PEAK PEAK 10. RL = 100Ω, VOUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay. 11. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only. 12. VIN = +2V, DISABLE = +5V to 0V. Measured from the 50% point of DISABLE to VOUT = 0V. 13. VIN = +2V, DISABLE = 0V to +5V. Measured from the 50% point of DISABLE to VOUT = 2V. 14. VIN = 0V, Force VOUT from 0V to ±2.5V, tR = tF = 50ns, DISABLE = 0V. 15. Measured with a VM700A video tester using an NTC-7 composite VITS. 16. VOUT = ±2.5V. At -40oC Product is tested at VOUT = ±2.25V because short test duration does not allow self heating. 4 HA5022 Test Circuits and Waveforms + DUT 50Ω HP4195 NETWORK ANALYZER 50Ω FIGURE 1. TEST CIRCUIT FOR TRANSIMPEDANCE MEASUREMENTS (NOTE 17) 100Ω (NOTE 17) 100Ω VIN + VIN DUT VOUT - 50Ω RL 100Ω + DUT VOUT - 50Ω RI 681Ω RF , 681Ω RL 400Ω RF , 1kΩ FIGURE 2. SMALL SIGNAL PULSE RESPONSE CIRCUIT FIGURE 3. LARGE SIGNAL PULSE RESPONSE CIRCUIT NOTE: 17. A series input resistor of ≥100Ω is recommended to limit input currents in case input signals are present before the HA5022 is powered up. Vertical Scale: VIN = 100mV/Div., VOUT = 100mV/Div. Horizontal Scale: 20ns/Div. FIGURE 4. SMALL SIGNAL RESPONSE 5 Vertical Scale: VIN = 1V/Div., VOUT = 1V/Div. Horizontal Scale: 50ns/Div. FIGURE 5. LARGE SIGNAL RESPONSE Schematic Diagram (One Amplifier of Two) V+ R5 2.5K R2 800 R6 15K R10 820 D2 QP8 R15 400 QP9 R19 400 QP1 QP5 R11 1K R17 280 QN5 R24 140 6 QN12 R7 15K QN1 QP6 QN6 -IN R12 280 QP4 QP17 QN13 +IN QN17 R25 20 C2 1.4pF QN15 QN2 R21 140 QN10 QP7 QN4 R14 280 R22 280 QN14 R16 400 QN21 R25 140 QN16 R13 1K QN7 HA5022 QP13 R3 6K QN3 QP20 R28 20 DIS D1 QP16 QP12 QP3 R31 5 QP15 C1 1.4pF QN8 R1 60K QP19 R20 140 1.25K QP2 QP18 R18 280 QP10 R8 200 QP14 QP11 R29 9.5 R33 2K R27 QN18 R23 400 R26 200 R32 5 QN19 QN20 R26 200 R30 7 OUT R4 800 V- R33 800 R9 820 QN9 QN11 HA5022 Application Information as short as possible to minimize the capacitance from this node to ground. Optimum Feedback Resistor The plots of inverting and non-inverting frequency response, see Figure 11 and Figure 12 in the Typical Performance Curves section, illustrate the performance of the HA5022 in various closed loop gain configurations. Although the bandwidth dependency on closed loop gain isn’t as severe as that of a voltage feedback amplifier, there can be an appreciable decrease in bandwidth at higher gains. This decrease may be minimized by taking advantage of the current feedback amplifier’s unique relationship between bandwidth and RF . All current feedback amplifiers require a feedback resistor, even for unity gain applications, and RF , in conjunction with the internal compensation capacitor, sets the dominant pole of the frequency response. Thus, the amplifier’s bandwidth is inversely proportional to RF . The HA5022 design is optimized for a 1000Ω RF at a gain of +1. Decreasing RF in a unity gain application decreases stability, resulting in excessive peaking and overshoot. At higher gains the amplifier is more stable, so RF can be decreased in a trade-off of stability for bandwidth. The table below lists recommended RF values for various gains, and the expected bandwidth. GAIN (ACL) BANDWIDTH (MHz) RF (Ω) -1 750 100 +1 1000 125 +2 681 95 +5 1000 52 +10 383 65 -10 750 22 Driving Capacitive Loads Capacitive loads will degrade the amplifier’s phase margin resulting in frequency response peaking and possible oscillations. In most cases the oscillation can be avoided by placing an isolation resistor (R) in series with the output as shown in Figure 6. 100Ω VIN R + VOUT - RT CL RF RI FIGURE 6. PLACEMENT OF THE OUTPUT ISOLATION RESISTOR, R The selection criteria for the isolation resistor is highly dependent on the load, but 27Ω has been determined to be a good starting value. Power Dissipation Considerations Due to the high supply current inherent in dual amplifiers, care must be taken to insure that the maximum junction temperature (TJ, see Absolute Maximum Ratings) is not exceeded. Figure 7 shows the maximum ambient temperature versus supply voltage for the available package styles (PDIP, SOIC). At VS = ±5V quiescent operation both package styles may be operated over the full industrial range of -40oC to 85oC. It is recommended that thermal calculations, which take into account output power, be performed by the designer. PC Board Layout Attention must be given to decoupling the power supplies. A large value (10µF) tantalum or electrolytic capacitor in parallel with a small value (0.1µF) chip capacitor works well in most cases. A ground plane is strongly recommended to control noise. Care must also be taken to minimize the capacitance to ground seen by the amplifier’s inverting input (-IN). The larger this capacitance, the worse the gain peaking, resulting in pulse overshoot and possible instability. It is recommended that the ground plane be removed under traces connected to -IN, and that connections to -IN be kept 7 140 MAX. AMBIENT TEMPERATURE The frequency response of this amplifier depends greatly on the amount of care taken in designing the PC board. The use of low inductance components such as chip resistors and chip capacitors is strongly recommended. If leaded components are used the leads must be kept short especially for the power supply decoupling components and those components connected to the inverting input. 130 PDIP 120 110 100 90 SOIC 80 5 7 9 11 13 15 SUPPLY VOLTAGE (±V) FIGURE 7. MAXIMUM OPERATING AMBIENT TEMPERATURE vs SUPPLY VOLTAGE Enable/Disable Function When enabled the amplifier functions as a normal current feedback amplifier with all of the data in the electrical specifications table being valid and applicable. When HA5022 disabled the amplifier output assumes a true high impedance state and the supply current is reduced significantly. The circuit shown in Figure 8 is a simplified schematic of the enable/disable function. The large value resistors in series with the DISABLE pin makes it appear as a current source to the driver. When the driver pulls this pin low current flows out of the pin and into the driver. This current, which may be as large as 350µA when external circuit and process variables are at their extremes, is required to insure that point “A” achieves the proper potential to disable the output. The driver must have the compliance and capability of sinking all of this current. V+ R6 15K R10 R33 QP18 D1 R8 R7 15K A QP3 ENABLE/DISABLE INPUT FIGURE 8. SIMPLIFIED SCHEMATIC OF ENABLE/DISABLE FUNCTION When VCC is +5V the DISABLE pin may be driven with a dedicated TTL gate. The maximum low level output voltage of the TTL gate, 0.4V, has enough compliance to insure that the amplifier will always be disabled even though D1 will not turn on, and the TTL gate will sink enough current to keep point “A” at its proper voltage. When VCC is greater than +5V the DISABLE pin should be driven with an open collector device that has a breakdown rating greater than VCC . Referring to Figure 8, it can be seen that R6 will act as a pullup resistor to +VCC if the DISABLE pin is left open. In those cases where the enable/disable function is not required on all circuits some circuits can be permanently enabled by letting the DISABLE pin float. If a driver is used to set the enable/disable level, be sure that the driver does not sink more than 20µA when the DISABLE pin is at a high level. TTL gates, especially CMOS versions, do not violate this criteria so it is permissible to control the enable/disable function with TTL. Typical Applications Two Channel Video Multiplexer Referring to the amplifier U1A in Figure 9, R1 terminates the cable in its characteristic impedance of 75Ω, and R4 back terminates the cable in its characteristic impedance. The amplifier is set up in a gain configuration of +2 to yield an overall network gain of +1 when driving a double terminated cable. The value of R3 can be changed if a different network gain is desired. R5 holds the disable pin at ground thus inhibiting the amplifier until the switch, S1, is thrown to 8 position 1. At position 1 the switch pulls the disable pin up to the plus supply rail thereby enabling the amplifier. Since all of the actual signal switching takes place within the amplifier, it’s differential gain and phase parameters, which are 0.03% and 0.03 degrees respectively, determine the circuit’s performance. The other circuit, U1B, operates in a similar manner. When the plus supply rail is 5V the disable pin can be driven by a dedicated TTL gate as discussed earlier. If a multiplexer IC or its equivalent is used to select channels its logic must be break before make. When these conditions are satisfied the HA5022 is often used as a remote video multiplexer, and the multiplexer may be extended by adding more amplifier ICs. Low Impedance Multiplexer Two common problems surface when you try to multiplex multiple high speed signals into a low impedance source such as an A/D converter. The first problem is the low source impedance which tends to make amplifiers oscillate and causes gain errors. The second problem is the multiplexer which supplies no gain, introduces all kinds of distortion and limits the frequency response. Using op amps which have an enable/disable function, such as the HA5022, eliminates the multiplexer problems because the external mux chip is not needed, and the HA5022 can drive low impedance (large capacitance) loads if a series isolation resistor is used. Referring to Figure 10, both inputs are terminated in their characteristic impedance; 75Ω is typical for video applications. Since the drivers usually are terminated in their characteristic impedance the input gain is 0.5, thus the amplifiers, U2, are configured in a gain of +2 to set the circuit gain equal to one. Resistors R2 and R3 determine the amplifier gain, and if a different gain is desired R2 should be changed according to the equation G = (1 + R3/R2). R3 sets the frequency response of the amplifier so you should refer to the manufacturers data sheet before changing its value. R5, C1 and D1 are an asymmetrical charge/discharge time circuit which configures U1 as a break before make switch to prevent both amplifiers from being active simultaneously. If this design is extended to more channels the drive logic must be designed to be break before make. R4 is enclosed in the feedback loop of the amplifier so that the large open loop amplifier gain of U2 will present the load with a small closed loop output impedance while keeping the amplifier stable for all values of load capacitance. The circuit shown in Figure 10 was tested for the full range of capacitor values with no oscillations being observed; thus, problem one has been solved.The frequency and gain characteristics of the circuit are now those of the amplifier independent of any multiplexing action; thus, problem two has been solved. The multiplexer transition time is approximately 15µs with the component values shown. HA5022 (NOTE 17) U 100Ω 1 1A + 16 VIDEO INPUT #1 R1 75 2 R6 75 VIDEO OUTPUT TO 75Ω LOAD - 3 R5 2000 R2 681 R3 681 VIDEO INPUT #2 R4 75 1 2 (NOTE 17) U 100Ω 7 1B 10 6 +- R9 75 3 +5V IN R10 2000 R7 681 +5V +5V S1 ALL OFF 5 R8 681 R11 100 -5V IN -5V + 10µF 0.1µF 10µF 0.1µF + NOTES: 18. U1 is HA5022. 19. All resistors in Ω. 20. S1 is break before make. 21. Use ground plane. FIGURE 9. TWO CHANNEL HIGH IMPEDANCE MULTIPLEXER R3A 681 INPUT B R1A 681 R1A 75 R4A U2A 27 16 1 + 4 -5V 100Ω 2 3 (NOTE 17) 0.01µF INPUT A D1A 1N4148 R1B 75 U1C R5A 2000 R3B 681 R2B 681 C1A 0.047µF CHANNEL SWITCH 100Ω (NOTE 17) 7 U2B - 10 6 + 13 5 INHIBIT R6 100K U1B U1D D1B 1N4148 C1B 0.047µF NOTES: 22. U2: HA5022. 23. U1: CD4011. FIGURE 10. LOW IMPEDANCE MULTIPLEXER 9 OUTPUT +5V 0.01µF R5B 2000 U1A R4B 27 HA5022 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified 5 5 VOUT = 0.2VP-P CL = 10pF AV = +1, RF = 1kΩ 3 AV = 2, RF = 681Ω 2 AV = 5, RF = 1kΩ 3 1 0 -1 -2 -3 AV = -1 2 1 AV = -2 0 -1 -2 AV = -10 -3 AV = 10, RF = 383Ω AV = -5 -4 -4 -5 -5 10 FREQUENCY (MHz) 100 2 200 90 AV = -1, RF = 750Ω 45 AV = +10, RF = 383Ω -100 0 -225 -45 -270 -90 AV = -10, RF = 750Ω -315 -135 VOUT = 0.2VP-P CL = 10pF 2 -180 10 100 140 VOUT = 0.2VP-P CL = 10pF AV = +1 130 120 5 GAIN PEAKING 200 500 700 FREQUENCY (MHz) 100 0 1500 130 95 -3dB BANDWIDTH 90 10 5 GAIN PEAKING 500 650 800 950 0 1100 FEEDBACK RESISTOR (Ω) FIGURE 15. BANDWIDTH AND GAIN PEAKING vs FEEDBACK RESISTANCE 10 -3dB BANDWIDTH (MHz) VOUT = 0.2VP-P CL = 10pF AV = +2 GAIN PEAKING (dB) -3dB BANDWIDTH (MHz) 900 1100 1300 FEEDBACK RESISTOR (Ω) FIGURE 14. BANDWIDTH AND GAIN PEAKING vs FEEDBACK RESISTANCE FIGURE 13. PHASE RESPONSE AS A FUNCTION OF FREQUENCY 350 10 -3dB BANDWIDTH 120 -3dB BANDWIDTH 110 6 100 4 90 GAIN PEAKING VOUT = 0.2VP-P CL = 10pF AV = +1 80 0 200 400 600 800 2 0 1000 LOAD RESISTOR (Ω) FIGURE 16. BANDWIDTH AND GAIN PEAKING vs LOAD RESISTANCE GAIN PEAKING (dB) -360 -3dB BANDWIDTH (MHz) 180 135 -45 -135 200 FIGURE 12. INVERTING FREQUENCY RESPONSE INVERTING PHASE (DEGREES) AV = +1, RF = 1kΩ -90 100 FREQUENCY (MHz) FIGURE 11. NON-INVERTING FREQUENCY RESPONSE 0 10 GAIN PEAKING (dB) 2 NONINVERTING PHASE (DEGREES) VOUT = 0.2VP-P CL = 10pF RF = 750Ω 4 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 4 HA5022 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 16 80 VOUT = 0.1VP-P CL = 10pF VSUPPLY = ±5V, AV = +2 60 12 OVERSHOOT (%) -3dB BANDWIDTH (MHz) VOUT = 0.2VP-P CL = 10pF AV = +10 40 VSUPPLY = ±15V, AV = +2 6 20 VSUPPLY = ±5V, AV = +1 VSUPPLY = ±15V, AV = +1 0 0 200 350 500 650 800 950 0 200 400 FEEDBACK RESISTOR (Ω) 800 1000 FIGURE 18. SMALL SIGNAL OVERSHOOT vs LOAD RESISTANCE FIGURE 17. BANDWIDTH vs FEEDBACK RESISTANCE 0.08 0.10 FREQUENCY = 3.58MHz 0.08 DIFFERENTIAL PHASE (DEGREES) FREQUENCY = 3.58MHz DIFFERENTIAL GAIN (%) 600 LOAD RESISTANCE (Ω) RL = 75Ω 0.06 RL = 150Ω 0.04 0.02 RL = 1kΩ 0.06 0.04 RL = 150Ω RL = 75Ω 0.02 RL = 1kΩ 0.00 0.00 3 5 7 9 11 SUPPLY VOLTAGE (±V) 13 3 15 5 7 9 11 SUPPLY VOLTAGE (±V) 13 15 FIGURE 20. DIFFERENTIAL PHASE vs SUPPLY VOLTAGE FIGURE 19. DIFFERENTIAL GAIN vs SUPPLY VOLTAGE -40 VOUT = 2.0VP-P CL = 30pF 0 -10 REJECTION RATIO (dB) DISTORTION (dBc) -50 HD2 -60 3RD ORDER IMD -70 AV = +1 HD2 HD3 -80 -20 -30 -40 CMRR -50 -60 NEGATIVE PSRR -70 -80 POSITIVE PSRR HD3 -90 0.3 1 FREQUENCY (MHz) FIGURE 21. DISTORTION vs FREQUENCY 11 10 0.001 0.01 0.1 FREQUENCY (MHz) 1 10 FIGURE 22. REJECTION RATIOS vs FREQUENCY 30 HA5022 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 12 RL = 100Ω VOUT = 1.0VP-P AV = +1 RLOAD = 100Ω VOUT = 1.0VP-P PROPAGATION DELAY (ns) PROPAGATION DELAY (ns) 8.0 7.5 7.0 6.5 10 AV = +10, RF = 383Ω 8 AV = +2, RF = 681Ω 6 AV = +1, RF =1kΩ 4 6.0 -50 -25 0 25 50 75 TEMPERATURE (oC) 100 125 FIGURE 23. PROPAGATION DELAY vs TEMPERATURE 3 5 7 9 11 SUPPLY VOLTAGE (±V) 13 15 FIGURE 24. PROPAGATION DELAY vs SUPPLY VOLTAGE 0.8 500 VOUT = 2VP-P VOUT = 0.2VP-P CL = 10pF 0.6 450 SLEW RATE (V/µs) NORMALIZED GAIN (dB) 0.4 + SLEW RATE 400 350 - SLEW RATE 300 250 200 0.2 AV= +2, RF = 681Ω 0 -0.2 -0.4 AV= +5, RF = 1kΩ -0.6 AV = +1, RF = 1kΩ -0.8 150 -1.0 100 -1.2 -50 -25 0 25 50 75 TEMPERATURE (oC) 100 FIGURE 25. SLEW RATE vs TEMPERATURE 12 125 AV = +10, RF = 383Ω 5 10 15 20 FREQUENCY (MHz) 25 FIGURE 26. NON-INVERTING GAIN FLATNESS vs FREQUENCY 30 HA5022 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 0.8 100 VOUT = 0.2VP-P CL = 10pF RF = 750Ω 0.2 AV = -1 0 -0.2 -0.4 -0.6 AV = -5 -0.8 -1.0 600 60 +INPUT NOISE CURRENT 400 40 INPUT NOISE VOLTAGE 200 20 AV = -10 10 15 20 25 0 0.01 30 0.1 FREQUENCY (MHz) 1 FIGURE 28. INPUT NOISE CHARACTERISTICS 1.5 BIAS CURRENT (µA) 2 VIO (mV) 1.0 0.5 -40 -20 0 20 40 60 80 100 120 0 -2 -4 -60 140 -40 -20 0 40 60 80 100 120 140 FIGURE 30. +INPUT BIAS CURRENT vs TEMPERATURE FIGURE 29. INPUT OFFSET VOLTAGE vs TEMPERATURE 4000 TRANSIMPEDANCE (kΩ) 22 BIAS CURRENT (µA) 20 TEMPERATURE (oC) TEMPERATURE (oC) 20 18 16 -60 0 100 10 FREQUENCY (kHz) FIGURE 27. INVERTING GAIN FLATNESS vs FREQUENCY 0.0 -60 800 AV = -2 -1.2 5 -INPUT NOISE CURRENT 80 CURRENT NOISE (pA/√Hz) NORMALIZED GAIN (dB) 0.4 1000 AV = +10, RF = 383Ω VOLTAGE NOISE (nV/√Hz) 0.6 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (oC) FIGURE 31. -INPUT BIAS CURRENT vs TEMPERATURE 13 3000 2000 1000 -60 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (oC) FIGURE 32. TRANSIMPEDANCE vs TEMPERATURE 140 HA5022 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 74 25 REJECTION RATIO (dB) ICC (mA) 20 55oC 15 10 3 4 5 6 70 68 -PSRR 66 64 62 CMRR 60 25oC 5 +PSRR 72 125oC 7 8 9 10 11 12 13 14 58 -100 15 -50 0 100 200 150 250 FIGURE 34. REJECTION RATIO vs TEMPERATURE FIGURE 33. SUPPLY CURRENT vs SUPPLY VOLTAGE 40 4.0 30 +10V +5V +15V OUTPUT SWING (V) SUPPLY CURRENT (mA) 50 TEMPERATURE (oC) SUPPLY VOLTAGE (±V) 20 10 3.8 3.6 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (oC) DISABLE INPUT VOLTAGE (V) FIGURE 35. SUPPLY CURRENT vs DISABLE INPUT VOLTAGE FIGURE 36. OUTPUT SWING vs TEMPERATURE 30 1.2 VS = ±15V 1.1 VIO (mV) VOUT (VP-P) 20 VS = ±10V 1.0 10 0.9 VS = ±4.5V 0 0.01 0.8 0.10 1.00 LOAD RESISTANCE (kΩ) FIGURE 37. OUTPUT SWING vs LOAD RESISTANCE 14 10.00 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (oC) FIGURE 38. INPUT OFFSET VOLTAGE CHANGE BETWEEN CHANNELS vs TEMPERATURE HA5022 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 30 1.5 -55oC 1.0 ICC (mA) ∆BIAS CURRENT (µA) 25 20 25oC 15 0.5 10 125oC 5 0.0 -40 -20 0 20 40 60 80 100 120 3 140 4 5 6 7 TEMPERATURE (oC) FIGURE 39. INPUT BIAS CURRENT CHANGE BETWEEN CHANNELS vs TEMPERATURE 9 10 12 13 32 AV = +1 VOUT = 2VP-P ENABLE TIME (ns) -50 -60 16 26 14 ENABLE 24 12 22 10 20 8 18 6 DISABLE 16 -70 4 14 10 FIGURE 41. CHANNEL SEPARATION vs FREQUENCY 15 15 18 ENABLE 28 1 FREQUENCY (MHz) 14 20 30 -40 -80 0.1 11 FIGURE 40. DISABLE SUPPLY CURRENT vs SUPPLY VOLTAGE -30 SEPARATION (dB) 8 SUPPLY VOLTAGE (±V) 30 DISABLE TIME (µs) -60 2 DISABLE 12 -2.5 -2.0 -1.5 -1.0 -0.5 0 0.5 1.0 1.5 2.0 0 2.5 OUTPUT VOLTAGE (V) FIGURE 42. ENABLE/DISABLE TIME vs OUTPUT VOLTAGE HA5022 -20 -30 -40 -50 10 RL = 100Ω 1 0.1 0.01 180 0.001 135 90 45 -60 0 -70 -45 -80 -90 0.1 1 FREQUENCY (MHz) 10 20 TRANSIMPEDANCE (MΩ) FIGURE 43. DISABLE FEEDTHROUGH vs FREQUENCY 0.001 0.01 0.1 1 FREQUENCY (MHz) 10 -135 100 FIGURE 44. TRANSIMPEDANCE vs FREQUENCY 10 RL = 400Ω 1 0.1 0.01 180 0.001 135 90 45 0 -45 -90 -135 0.001 0.01 0.1 1 FREQUENCY (MHz) 10 PHASE ANGLE (DEGREES) FEEDTHROUGH (dB) -10 DISABLE = 0V VIN = 5VP-P RF = 750Ω PHASE ANGLE (DEGREES) 0 VSUPPLY = ±5V, AV = +1, RF = 1kΩ, RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) TRANSIMPEDANCE (MΩ) Typical Performance Curves 100 FIGURE 45. TRANSIMPEDENCE vs FREQUENCY All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 16 HA5022 Die Characteristics DIE DIMENSIONS: PASSIVATION: 1650µm x 2540µm x 483µm Type: Nitride Thickness: 4kÅ ±0.4kÅ METALLIZATION: TRANSISTOR COUNT: Type: Metal 1: AlCu (1%) Thickness: Metal 1: 8kÅ ±0.4kÅ Type: Metal 2: AlCu (1%) Thickness: Metal 2: 16kÅ ±0.8kÅ 124 PROCESS: High Frequency Bipolar Dielectric Isolation SUBSTRATE POTENTIAL (POWERED UP): V- Metallization Mask Layout HA5022 -IN1 OUT1 V+ +IN1 DIS1 VNC DIS2 +IN2 -IN2 17 OUT2