SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C Solid State DC Contactor Applications: ● Main DC Bus Switch ● DC Motor Bus Switch ● Battery Disconnect ● Bus Discharge Description: Sensitron has developed a small footprint High Voltage/High Current DC solid state Relay/Contactor. This device incorporates the latest state of the art technology to reduce the “on” state power losses and voltage drop to a minimum. The device is a true four terminal relay, and doesn’t need an additional power source for bias. This device uses robust magnetic coupling to achieve high isolation, reliability, and long life. The input control lead will accept any voltage from 4.6V to 36VDC. Features: 2000V Input to Output / Output to Baseplate Isolation Up to 1200V Blocking Up to 100A Continuous Current Up to 400A Surge Capability Single wide range DC input signal 4.6V to 36V Low Power Control, 0.5W Typ. Low “on” state resistance Fast turn on/turn off High Current Terminals Three Point Mounting Plate o RθJC ≤ 1.15 C/W 1.4” x 2.6” x .5” Input Control Specifications: Parameter Description V control DC Control Voltage Between pins 1 and 2 I control Input Current at control pins 1 and 2, Vin = 4.6V to 36V P control Control Input Power Consumption MIN 4.6 10 TYP MAX 36 150 Unit Volts mA 0.5 0.69 Watt 0.12 0.10 Iin(A) 0.08 0.06 0.04 0.02 0.00 0 10 20 30 40 Vin(Vdc) Fig. 1 – Typical Input Current vs. Input Volt ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 1 SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C SSRxxxD005 (50V Models) Output Specifications: Parameter VOUT ILEAK IOUT ISURGE ILATCH RON RON VDROP VDROP COUT EAS VSD trr Description Max Blocking Voltage Across Pins 3 and 4 Output leakage o TJ = 25 C, VDS = 50V, VGS = 0V o (1) TJ = 125 C, VDS = 50V, VGS = 0V Max Continuous Contact Current SSR033D005 SSR066D005 SSR100D005 o Output Surge Current Capability, TJ = 25 C 250µS Pulse o Over Current latch, at 25 C SSR033D005 SSR066D005 SSR100D005 o Contact Resistance, TJ = 25 C o (1) Contact Resistance, TJ = 150 C o Voltage drop at Iout, TJ = 25 C SSR033D005 SSR066D005 SSR100D005 o (1) Voltage drop at Iout, TJ = 150 C SSR033D005 SSR066D005 SSR100D005 Capacitance, VDS=50V, f=100kHz Avalanche energy, single pulse TJ = 25 °C, ID = 120A, VDS = 50V, L = 23µH Reverse Diode VF, at Iout, TJ = 25 °C IF = 75A, di/dt = 100A/µs, VR = 40V Reverse recovery time, TJ = 25 °C IF = 75A, di/dt = 100A/µs, VR = 40V MIN TYP 0 0 0 MAX 50 Unit VDC 60 750 µA 33 66 100 1400 265 400 400 2.3 3.0 2.9 3.8 0.076 0.152 0.230 0.096 0.191 0.290 A A(pk) A(pk) 0.126 0.251 0.380 2160 mOhm mOhm VDC VDC pF 170 mJ 1.3 VDC 50 ns ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 2 SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C SSRxxxD010 (100V Models) Output Specifications: Parameter VOUT ILEAK IOUT ISURGE ILATCH RON RON VDROP VDROP COUT EAS VSD trr Description Max Blocking Voltage Across Pins 3 and 4 Output leakage o TJ = 25 C, VDS = 100V, VGS = 0V o (1) TJ = 125 C, VDS = 100V, VGS = 0V Max Continuous Contact Current SSR033D010 SSR066D010 SSR100D010 o Output Surge Current Capability, TJ = 25 C 250µS Pulse o Over Current latch, at 25 C SSR033D010 SSR066D010 SSR100D010 o Contact Resistance, TJ = 25 C o (1) Contact Resistance, TJ = 150 C o Voltage drop at Iout, TJ = 25 C SSR033D010 SSR066D010 SSR100D010 o (1) Voltage drop at Iout, TJ = 150 C SSR033D010 SSR066D010 SSR100D010 Capacitance, VDS=50V, f=100kHz Avalanche energy, single pulse TJ = 25 °C, ID = 75A, VDS = 50V, L = 47µH Reverse Diode VF, at Iout, TJ = 25 °C IF = 75A, di/dt = 100A/µs, VR = 85V Reverse recovery time, TJ = 25 °C IF = 75A, di/dt = 100A/µs, VR = 85V MIN TYP 0 0 0 MAX 100 Unit VDC 60 750 µA 33 66 100 1200 265 400 400 3.1 5.0 4.1 6.8 0.103 0.205 0.310 0.133 0.266 0.403 A A(pk) A(pk) 0.224 0.448 0.679 1470 mOhm mOhm VDC VDC pF 130 mJ 1.3 VDC 40 ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 3 ns SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C SSRxxxD020 (200V Models) Output Specifications: Parameter VOUT ILEAK IOUT ISURGE ILATCH RON RON VDROP VDROP COUT EAS VSD trr Description Max Blocking Voltage Across Pins 3 and 4 Output leakage o TJ = 25 C, VDS = 200V, VGS = 0V o (1) TJ = 125 C, VDS = 200V, VGS = 0V Max Continuous Contact Current SSR025D020 SSR033D020 SSR066D020 o Output Surge Current Capability, TJ = 25 C 250µS Pulse o Over Current latch, at 25 C SSR025D020 SSR033D020 SSR066D020 o Contact Resistance, TJ = 25 C o (1) Contact Resistance, TJ = 150 C o Voltage drop at Iout, TJ = 25 C SSR025D020 SSR033D020 SSR066D020 o (1) Voltage drop at Iout, TJ = 150 C SSR025D020 SSR033D020 SSR066D020 Capacitance, VDS=25V, f=100kHz Avalanche energy, single pulse TJ = 25 °C, ID = 60A, VDS = 50V Reverse Diode VF, at Iout, TJ = 25 °C IF = 81A, di/dt = 100A/µs Reverse recovery time, TJ = 25 °C IF = 81A, di/dt = 100A/µs MIN TYP 0 0 0 MAX 200 Unit VDC 60 750 µA 25 33 66 600 200 265 400 4.2 8.7 5.5 11.8 0.104 0.138 0.275 0.137 0.180 0.360 A A(pk) A(pk) 0.295 0.390 0.777 2430 mOhm mOhm VDC VDC pF 760 mJ 1.3 VDC 130 ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 4 ns SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C SSRxxxD060 (600V Models) Output Specifications: Parameter VOUT ILEAK IOUT ISURGE ILATCH RON RON VDROP VDROP COUT EAS VSD trr Description Max Blocking Voltage Across Pins 3 and 4 Output leakage o TJ = 25 C, VDS = 600V, VGS = 0V o (1) TJ = 125 C, VDS = 600V, VGS = 0V Max Continuous Contact Current SSR015D060 SSR025D060 SSR033D060 SSR050D060 o Output Surge Current Capability, TJ = 25 C 250µS Pulse o Over Current latch, at 25 C SSR015D060 SSR025D060 SSR033D060 SSR050D060 o Contact Resistance, TJ = 25 C o (1) Contact Resistance, TJ = 150 C o Voltage drop at Iout, TJ = 25 C SSR015D060 SSR025D060 SSR033D060 SSR050D060 o (1) Voltage drop at Iout, TJ = 150 C SSR015D060 SSR025D060 SSR033D060 SSR050D060 Capacitance, VDS=100V, f=100kHz Avalanche energy, single pulse TJ = 25 °C, ID = 15A, VDS = 50V Reverse Diode VF, at Iout, TJ = 25 °C ISD = 84A, di/dt = 100A/µs, VDS = 100V Reverse recovery time, TJ = 25 °C ISD = 84A, di/dt = 100A/µs, VDS = 100V MIN TYP 0 0 0 0 MAX 600 Unit VDC 3 300 µA 15 25 33 50 600 120 200 265 400 9.5 19.1 12.3 25.1 0.143 0.238 0.314 0.475 0.185 0.308 0.406 0.615 A A(pk) A(pk) 0.376 0.627 0.827 1.253 669 mOhm mOhm VDC VDC pF 2000 mJ 1.5 VDC 544 ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 5 ns SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C SSRxxxD080 (800V Models) Output Specifications: Parameter VOUT ILEAK IOUT ISURGE ILATCH RON RON VDROP VDROP COUT EAS VSD trr Description Max Blocking Voltage Across Pins 3 and 4 Output leakage o TJ = 25 C, VDS = 800V, VGS = 0V o (1) TJ = 125 C, VDS = 800V, VGS = 0V Max Continuous Contact Current SSR015D080 SSR025D080 SSR033D080 o Output Surge Current Capability, TJ = 25 C 250µS Pulse o Over Current latch, at 25 C SSR015D080 SSR025D080 SSR033D080 o Contact Resistance, TJ = 25 C o (1) Contact Resistance, TJ = 150 C o Voltage drop at Iout, TJ = 25 C SSR015D080 SSR025D080 SSR033D080 o (1) Voltage drop at Iout, TJ = 150 C SSR015D080 SSR025D080 SSR033D080 Capacitance, VDS=1000V, f=100kHz Avalanche energy, single pulse TJ = 25 °C, ID = 40A, VDS = 50V Reverse Diode VF, at Iout, TJ = 25 °C IF = 20A, di/dt = 1000A/µs, VR = 800V Reverse recovery time, TJ = 25 °C IF = 20A, di/dt = 1000A/µs, VR = 800V MIN TYP 0 0 0 MAX 800 Unit VDC 3 300 µA 15 25 33 400 120 200 265 14.9 29.5 20.7 41.7 0.225 0.371 0.490 0.311 0.518 0.684 A A(pk) A(pk) 0.626 1.043 1.376 450 mOhm mOhm VDC VDC pF 2000 mJ 3.3 VDC 54 ns ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 6 SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C SSRxxxD120 (1200V Models) Output Specifications: Parameter VOUT ILEAK IOUT ISURGE ILATCH RON RON VDROP VDROP COUT EAS VSD trr Description Max Blocking Voltage Across Pins 3 and 4 Output leakage o TJ = 25 C, VDS = 1200V, VGS = 0V o (1) TJ = 125 C, VDS = 1200V, VGS = 0V Max Continuous Contact Current SSR015D120 SSR025D120 SSR033D120 o Output Surge Current Capability, TJ = 25 C 250µS Pulse o Over Current latch, at 25 C SSR015D120 SSR025D120 SSR033D120 o Contact Resistance, TJ = 25 C o (1) Contact Resistance, TJ = 150 C o Voltage drop at Iout, TJ = 25 C SSR015D120 SSR025D120 SSR033D120 o (1) Voltage drop at Iout, TJ = 150 C SSR015D120 SSR025D120 SSR033D120 Capacitance, VDS=1000V, f=100kHz Avalanche energy, single pulse TJ = 25 °C, ID = 40A, VDS = 50V Reverse Diode VF, at Iout, TJ = 25 °C IF = 20A, di/dt = 1000A/µs, VR = 800V Reverse recovery time, TJ = 25 °C IF = 20A, di/dt = 1000A/µs, VR = 800V MIN TYP 0 0 0 MAX 1200 Unit VDC 3 300 µA 15 25 33 400 120 200 265 14.9 29.5 20.7 41.7 0.225 0.371 0.490 0.311 0.518 0.684 A A(pk) A(pk) 0.626 1.043 1.376 450 mOhm mOhm VDC VDC pF 2000 mJ 3.3 VDC 54 ns Notes: 1. These parameters are controlled via design or process and are not directly tested. Parameters are characterized on initial design release and upon design changes which would affect these characteristics. ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 7 SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C Fig. 3 – Block Diagram Fig. 4 – Input vs. Output Timing Fig. 5 – Over Current Fault Shut Down Switching Characteristics: Parameter Description ton “Contact” turn on time toff “Contact” turn off time tdon Delay from input command to contact on tdoff Delay from input command to contact off Delay to latch after detection of Over tdlatch Current, Iout = Ilatch +10%, Tj = 25 °C Fswitch Repetitive on to off switching frequency MIN - TYP 0.5 0.6 2.3 0.2 MAX 3 1.5 Unit us us ms ms - 50 150 us - - 200 Hz ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 8 SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C Environmental Parameter Isolation Isolation TSTG TCASE TJ RθJC Description Input to Output, <1mA Input or Output to Case, <1mA Storage Temperature Operating Temperature (Baseplate) Operating Temperature (Junction) Thermal Resistance (Baseplate – Junction) Weight MIN 2000 2000 -55 -55 -55 - TYP 0.9 85 MAX 150 100 150 1.15 - Mechanical Outline Over Current Disable Pin Diameter = 0.025” ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 9 Unit VDC VDC o C o C o C o C/W g SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C Pin Assigments: Input – Apply a positive voltage to this pin with respect to pin Gnd to “close” the contacts. GND – This is the return pin for the Input control voltage. +OUTPUT – This is the positive terminal of the “contact”. -OUTPUT – this is the return terminal for the +OUTPUT pin. Note: 1. Input pins and output pins are isolated up to 2000VDC 2. The device may be damaged if the input polarity is reversed. 3. The “contact” is uni-polar; a voltage reversal will result in current flow in the internal diode. Application Notes: A. Input Bias The SSR will be energized and the “Contact” will be closed, when a positive potential of 4.6VDC to 36VDC is applied between Input and Gnd. The input power consumption will be constant throughout the control voltage range therefore the contactor will draw more current at lower control voltages. DC Supply TTL with Buffer ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 10 SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C Input Driven from TTL with Open Drain Driver B. Output Load Connection The output circuit is completely floating therefore the Load can be connected to either output terminal. Load connected to +Output Terminal Load Connected to –Output Terminal C. Over Current Disable The SSR contains an Over Current latch which disables (opens) the contact whenever a large current in excess of the latching current is detected. The latch can only be reset be removing and re-applying the input control power. In noisy environments and in applications where high surge currents are encountered, the latch may be triggered prematurely. In these applications the latch circuit can be disabled by placing a short circuit between the over current disable terminals. ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 11 SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C D. Contact Protection The user must insure that the peak voltage rating of the SSR is not exceeded. The SSRXXDXXX family of devices switch at extremely fast speeds, therefore extra care must be taken to suppress voltage transients that are generated when interrupting high currents. Sensitron strongly advises the user to us a snubber network similar in design to the one shown below. This is an energy absorbing snubber that transfers the energy from any parasitic line inductance into the capacitor and then is dissipated through the resistor. The capacitor should be sized so that the captured energy does not charge the capacitor beyond the contacts rated voltage. E. AC Operation The contactor can be used for AC loads if two devices are connected “back to back”. ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 12 SENSITRON SEMICONDUCTOR SSR Series TECHNICAL DATA DATASHEET 5475, REV. C Part Number Ordering Information 1 S 2 3 4 S R 0 5 6 5 0 6 7 8 9 10 D 0 6 0 Communication Interface D = Discrete Product Family SSR = Solid State Relay 015 = 15A 025 = 25A 033 = 33A 050 = 50A 066 = 66A 100 = 100A Continuous Current Rating (600V, 800V, 1200V Models) (200V, 600V, 800V, 1200V Models) (600V Model) (50V, 100V, 200V Models) (50V, 100V Models) Max Blocking Voltage 005 = 50V 010 = 100V 020 = 200V 060 = 600V 080 = 800V 120 = 1200V Available Part Numbers 50V Models: 100V Models: 200V Models: 600V Models: 800V Models: 1200V Models: SSR033D005, SSR033D010, SSR025D020, SSR015D060, SSR015D080, SSR015D120, SSR066D005, SSR066D010, SSR033D020, SSR025D060, SSR025D080, SSR025D120, SSR100D005 SSR100D010 SSR066D020 SSR033D060, SSR033D080 SSR033D120 SSR050D060 DISCLAIMER: 1- The information given herein, including the specifications and dimensions, is subject to change without prior notice to improve product characteristics. Before ordering, purchasers are advised to contact the Sensitron Semiconductor sales department for the latest version of the datasheet(s). 2- In cases where extremely high reliability is required (such as use in nuclear power control, aerospace and aviation, traffic equipment, medical equipment , and safety equipment) , safety should be ensured by using semiconductor devices that feature assured safety or by means of users’ fail-safe precautions or other arrangement . 3- In no event shall Sensitron Semiconductor be liable for any damages that may result from an accident or any other cause during operation of the user’s units according to the datasheet(s). Sensitron Semiconductor assumes no responsibility for any intellectual property claims or any other problems that may result from applications of information, products or circuits described in the datasheets. 4- In no event shall Sensitron Semiconductor be liable for any failure in a semiconductor device or any secondary damage resulting from use at a value exceeding the absolute maximum rating. 5- No license is granted by the datasheet(s) under any patents or other rights of any third party or Sensitron Semiconductor. 6- The datasheet(s) may not be reproduced or duplicated, in any form, in whole or part, without the expressed written permission of Sensitron Semiconductor. 7- The products (technologies) described in the datasheet(s) are not to be provided to any party whose purpose in their application will hinder maintenance of international peace and safety nor are they to be applied to that purpose by their direct purchasers or any third party. When exporting these products (technologies), the necessary procedures are to be taken in accordance with related laws and regulations. ©2016 Sensitron Semiconductor 221 West Industry Court Deer Park, NY 11729 (631) 586 7600, FAX 631 242 9798 www.sensitron.com [email protected] Page 13