AK1220

[AK1220]
AK1220
900MHz High Linearity Mixer
1. Overview
The AK1220 is high linearity mixer. RF and Lo frequency range coverage from 100 to 900MHz and IF coverage is
from 20 to 100MHz. The RF input provides single-ended 50 interface. Lo ports are 50 matched and
complementary inputs should be decoupled to the ground. IF output ports are differential open drain outputs.
The linearity and Power consumption performances can optimize with the resistance connected to the BIAS Pin.
2. Features

Operating Frequency:

Linearity vs Power Selectable architecture
100 to 900MHz
Power Consumption: 17mA, IIP3:+22dBm, Gain:1dB, NF:10.5dB
Power Consumption: 9mA, IIP3:+11dBm, Gain:0.5dB, NF:10dB

Lo input level:
0dBm±5dB

Operating Supply Voltage:
4.75 to 5.25 V

Package:
16pin UQFN(0.5mm pitch, 3mm x 3mm x 0.60mm)

Operating Temperature Range:
-40 to 85C
3. Applications

Two-way Radios (PMR/LMR)

Radio Communications for disaster prevention

Marine Radios

Amateur Radios
MS1165-E-03
1
2014/10
[AK1220]
4. Table of Contents
1.
Overview ___________________________________________________________________________ 1
2.
Features ___________________________________________________________________________ 1
3.
Applications ________________________________________________________________________ 1
4.
Table of Contents ____________________________________________________________________ 2
5.
Block Diagram ______________________________________________________________________ 3
6.
System Diagram _____________________________________________________________________ 4
7.
Pin Functional Description _____________________________________________________________ 5
8.
Absolute Maximum Ratings ____________________________________________________________ 7
9.
Recommended Operating Range ________________________________________________________ 7
10.
Electrical Characteristics_______________________________________________________________ 8
11.
Typical Performance __________________________________________________________________ 9
12.
Typical Evaluation Board Schematic _____________________________________________________ 16
13.
IC Interface Schematic _______________________________________________________________ 24
14.
Application Information _______________________________________________________________ 25
15.
Outer Dimensions ___________________________________________________________________ 30
16.
Marking ___________________________________________________________________________ 31
MS1165-E-03
2
2014/10
[AK1220]
BIAS
5. Block Diagram
LOINP
Iref
Lo Buffer
LOINN
IFOUTP
RFIN
Mixer
VSS
VDD
IFOUTN
Figure 1. Block Diagram
MS1165-E-03
3
2014/10
[AK1220]
6. System Diagram
VSS
Current Adjustment Resistor
AK1220
LO Input
BIAS
LOINP
LO Buffer
Iref
LOINN
VSS
VSS
RF Input
VDD
(Powefeeding for Open-drain Output)
IFOUTP
Mixer
Output Load Resistor
RLoad
BALUN
IF Output
RFIN
IFOUTN
VDD
VDD
VSS
VSS
VSS
Figure 2. System Diagram
MS1165-E-03
4
2014/10
[AK1220]
7. Pin Functional Description
Table 1 Pin Function
No.
Name
I/O
Pin Functions
1
RFIN
AI
RF Input
2
VSS
G
Ground pin
3
LOINN
AI
Lo Input Negative
4
LOINP
AI
Lo Input Positive
5
NC
-
Non Connect
6
NC
-
Non Connect
7
NC
-
Non Connect
8
NC
-
Non Connect
BIAS
9
Resistance pin for current
Remarks
Connecting a inductor between this pin and ground.
Connecting a resistor between this pin and ground.
AIO
adjustment
10
VDD
P
IFOUTN
11
Power Supply
IF Output Negative
This pin is open drain output.
AO
It needs power feeding via a inductor.
IFOUTP
12
IF Output Positive
This pin is open drain output.
AO
It needs power feeding via a inductor.
13
NC
-
Non Connect
14
NC
-
Non Connect
15
NC
-
Non Connect
16
NC
-
Non Connect
Note) It is recommended to connect NC pins to ground, although it will not make any impact on the electrical
characteristics if the pin is open.
AI: Analog input pin
P: Power supply pin
MS1165-E-03
AO: Analog output pin
G: Ground pin
AIO: Analog I/O pin
5
2014/10
LOINN
3
LOINP
4
NC
NC
NC
13
TOP
VIEW
5
6
7
8
NC
2
14
NC
VSS
15
NC
1
16
NC
RFIN
NC
[AK1220]
12
IFOUTP
11
IFOUTN
10
VDD
9
BIAS
Figure 3. Package Pin Layout
MS1165-E-03
6
2014/10
[AK1220]
8. Absolute Maximum Ratings
Table 2 Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Unit
-0.3
5.5
V
Supply Voltage
VDD
RF Input Power
RFPOW
12
dBm
LO Input Power
LOPOW
12
dBm
Storage Temperature
Tstg
125
C
-55
Remarks
Exceeding these maximum ratings may result in damage to the AK1220. Normal operation is not guaranteed at
these extremes.
9. Recommended Operating Range
Table 3 Recommended Operating Range
Parameter
Symbol
Min.
Operating
Temperature
Ta
-40
Supply Voltage
VDD
4.75
Typ.
5
Max.
Unit
85
C
5.25
V
Remarks
The specifications are applicable within the recommended operating range (supply voltage/operating temperature).
MS1165-E-03
7
2014/10
[AK1220]
10. Electrical Characteristics
1.Analog Circuit Characteristics
Unless otherwise noted IF output=50MHz, Lo Input Level=-5dBm to +5dBm,
Output Load Resistor (RLoad)=2.2k, VDD=4.75 to 5.25V, Ta=-40 to 85C
Parameter
Min.
Typ.
Max.
Unit
Remarks
RF Input Frequency
100
900
MHz
Lo Input Frequency
100
900
MHz
IF output Frequency
20
100
MHz
Lo Input Power
-5
+5
dBm
Current Adjustment Resistor(BIAS)
22
56
k
17
24
mA
The total current of VDD
mA
pin,
9
13
IDD
BIAS=22k
0
BIAS=56k
IFOUTP
pin
and
IFOUTN pin.
RFIN=600MHz, Output Load Resistor = 22k
Conversion Gain
-1
SSB Noise Figure
1
3
dB
10.5
13
dB
IP1dB
+4
+7
dBm
IIP3
+19
+22
dBm
RFIN=600MHz, Output Load Resistor = 56k
Conversion Gain
-1.5
SSB Noise Figure
0.5
2.5
dB
10
12.5
dB
IP1dB
-2
+1
dBm
IIP3
+8
+11
dBm
Note 1) In the shipment test, NC pins and the exposed pad on the center of the back of the package is connected
to ground.
MS1165-E-03
8
2014/10
[AK1220]
11. Typical Performance
Unless otherwise noted, RF input =600MHz, Lo input =550MHz,IF output =50MHz,
Output Load Resistor (RLoad)=2.2k
1. Current Adjustment Resistor vs. IIP, NF, P1dB, Gain, IDD
26.0
16.0
24.0
15.0
14.0
20.0
NF [dB]
IIP3 [dBm]
22.0
18.0
16.0
14.0
13.0
12.0
11.0
12.0
10.0
10.0
9.0
8.0
8.0
20
30
40
50
60
20
30
40
50
60
50
60
BIAS [kohm]
10.0
5.0
9.0
4.0
8.0
3.0
7.0
2.0
6.0
1.0
Gain [dB]
IP1dB [dBm]
BIAS [kohm]
5.0
4.0
0.0
-1.0
3.0
-2.0
2.0
-3.0
1.0
-4.0
0.0
-5.0
20
30
40
50
60
20
BIAS [kohm]
30
40
BIAS [kohm]
24.0
22.0
IDD [mA]
20.0
18.0
16.0
14.0
12.0
10.0
8.0
20
30
40
50
60
BIAS [kohm]
Figure 4.
Note 1)
Current Adjustment Resistor vs. IIP3, NF, P1dB, Gain, IDD
A resistor with 5% tolerance are used.
MS1165-E-03
9
2014/10
[AK1220]
2.
Over temperature vs. IIP3, NF, P1dB, Gain, IDD
24.0
16.0
22.0
15.0
BIAS=22kohm
BIAS=56kohm
18.0
NF [dB]
IIP3 [dBm]
BIAS=22kohm
BIAS=56kohm
14.0
20.0
16.0
14.0
13.0
12.0
11.0
10.0
12.0
9.0
10.0
8.0
-40
-20
0
20
40
60
80
100
-40
-20
0
Temperature [deg]
10.0
40
60
80
100
5.0
9.0
4.0
BIAS=22kohm
BIAS=56kohm
8.0
3.0
7.0
2.0
6.0
1.0
Gain [dB]
IP1dB [dBm]
20
Temperature [deg]
5.0
4.0
0.0
-1.0
3.0
-2.0
2.0
-3.0
1.0
-4.0
0.0
BIAS=22kohm
BIAS=56kohm
-5.0
-40
-20
0
20
40
60
80
100
-40
Temperature [deg]
-20
0
20
40
60
80
100
Temperature [deg]
24.0
BIAS=22kohm
BIAS=56kohm
22.0
IDD [mA]
20.0
18.0
16.0
14.0
12.0
10.0
8.0
-40
-20
0
20
40
60
80
100
Temperature [deg]
Figure 5. Over temperature vs. IIP3, NF, P1dB, Gain, IDD
MS1165-E-03
10
2014/10
[AK1220]
24.0
16.0
22.0
15.0
20.0
14.0
BIAS=22kohm
BIAS=56kohm
18.0
NF [dB]
IIP3 [dBm]
3. Supply voltage vs. IIP3, NF, P1dB, Gain, IDD
16.0
14.0
13.0
12.0
11.0
10.0
12.0
9.0
10.0
8.0
4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25
4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25
VDD [V]
VDD [V]
10.0
9.0
8.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0.0
BIAS=22kohm
BIAS=56kohm
Gain [dB]
IP1dB [dBm]
BIAS=22kohm
BIAS=56kohm
5.0
4.0
3.0
2.0
1.0
0.0
-1.0
-2.0
-3.0
-4.0
-5.0
BIAS=22kohm
BIAS=56kohm
4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25
4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25
VDD [V]
VDD [V]
24.0
22.0
IDD [mA]
20.0
18.0
16.0
BIAS=22kohm
BIAS=56kohm
14.0
12.0
10.0
8.0
4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25
VDD [V]]
Figure 6. Supply voltage vs. IIP3, NF, P1dB, Gain, IDD
MS1165-E-03
11
2014/10
[AK1220]
4. RF input frequency vs. IIP3, NF, P1dB, Gain
24.0
16.0
22.0
15.0
NF [dB]
IIP3 [dBm]
BIAS=22kohm
BIAS=56kohm
18.0
16.0
14.0
13.0
12.0
11.0
10.0
12.0
9.0
10.0
8.0
100 200 300 400 500 600 700 800 900 1000
100 200 300 400 500 600 700 800 900 1000
RF Frequency [MHz]
RF Frequency [MHz]
10.0
5.0
9.0
8.0
4.0
3.0
7.0
6.0
2.0
1.0
5.0
4.0
Gain [dB]
IP1dB [dBm]
BIAS=22kohm
BIAS=56kohm
14.0
20.0
BIAS=22kohm
BIAS=56kohm
3.0
2.0
0.0
-1.0
BIAS=22kohm
BIAS=56kohm
-2.0
-3.0
1.0
0.0
-4.0
-5.0
100 200 300 400 500 600 700 800 900 1000
100 200 300 400 500 600 700 800 900 1000
RF Frequency [MHz]
RF Frequency [MHz]
Figure 7.
RF input frequency vs. IIP3, NF, P1dB, Gain
Note 1) AK1220 supports 100MHz to 900MHz RF Input.
MS1165-E-03
12
2014/10
[AK1220]
5. IF output frequency vs. IIP3, NF, P1dB, Gain
24.0
16.0
22.0
15.0
BIAS=22kohm
BIAS=56kohm
18.0
NF [dB]
IIP3 [dBm]
BIAS=22kohm
BIAS=56kohm
14.0
20.0
16.0
14.0
13.0
12.0
11.0
10.0
12.0
9.0
10.0
8.0
20
40
60
80
100
120
20
40
IF Frequency [MHz]
10.0
80
100
120
5.0
9.0
8.0
4.0
3.0
BIAS=22kohm
BIAS=56kohm
7.0
6.0
Gain [dB]
IP1dB [dBm]
60
IF Frequency [MHz]
5.0
4.0
2.0
1.0
0.0
-1.0
3.0
2.0
-2.0
-3.0
1.0
0.0
-4.0
-5.0
20
40
60
80
100
120
BIAS=22kohm
BIAS=56kohm
20
IF Frequency [MHz]
40
60
80
100
120
IF Frequency [MHz]
Figure 8. IF output frequency vs. IIP3, NF, P1dB, Gain
Note 1) AK1220 supports 20MHz to 100MHz IF Output.
MS1165-E-03
13
2014/10
[AK1220]
6. Lo input power vs. IIP3, NF, P1dB, Gain
24.0
16.0
22.0
15.0
BIAS=22kohm
BIAS=56kohm
18.0
NF [dB]
IIP3 [dBm]
BIAS=22kohm
BIAS=56kohm
14.0
20.0
16.0
14.0
13.0
12.0
11.0
10.0
12.0
9.0
10.0
8.0
-20
-15
-10
-5
0
5
10
-20
-15
10.0
5.0
9.0
4.0
8.0
3.0
7.0
2.0
6.0
BIAS=22kohm
BIAS=56kohm
5.0
4.0
-10
-5
0
5
10
Lo Input Level [dBm]
Gain [dB]
IP1dB [dBm]
Lo Input Level [dBm]
1.0
0.0
-1.0
3.0
-2.0
2.0
-3.0
1.0
-4.0
0.0
BIAS=22kohm
BIAS=56kohm
-5.0
-20
-15
-10
-5
0
5
10
-20
Lo Input Level [dBm]
-15
-10
-5
0
5
10
Lo Input Level [dBm]
Figure 9. Lo input power vs. IIP3, NF, P1dB, Gain
Note 1) AK1220 supports -5dBm to 5dBm Lo input power.
MS1165-E-03
14
2014/10
[AK1220]
7. Output Load Resistor(RLoad) vs. IIP3, NF, P1dB, Gain
24.0
16.0
22.0
15.0
BIAS=22kohm
BIAS=56kohm
18.0
NF [dB]
IIP3 [dBm]
BIAS=22kohm
BIAS=56kohm
14.0
20.0
16.0
14.0
13.0
12.0
11.0
10.0
12.0
9.0
10.0
8.0
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
1.4
1.6
1.8
10.0
5.0
9.0
4.0
8.0
3.0
7.0
2.0
6.0
BIAS=22kohm
BIAS=56kohm
5.0
2
2.2
2.4
2.6
2.8
RLoad [kohm]
Gain [dB]
IP1dB [dBm]
RLoad [kohm]
4.0
1.0
0.0
-1.0
3.0
-2.0
2.0
-3.0
1.0
-4.0
0.0
BIAS=22kohm
BIAS=56kohm
-5.0
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
1.4
1.6
RLoad [kohm]
Figure 10.
1.8
2
2.2
2.4
2.6
2.8
RLoad [kohm]
Output Load Resistor(RLoad) vs. IIP3, NF, P1dB, Gain
8.Leakage
RF input=600MHz, -20dBm, Lo input =600MHz, 0dBm, Ta=25C VDD=5V
Parameter
RF – Lo Lakage
RF – IF Lakage
Lo - RF Lakage
Lo - IF Lakage
MS1165-E-03
BIAS
Typ.
Unit
22k
-50
dBc
56k
-50
dBc
22k
-90
dBc
56k
-90
dBc
22k
-50
dBc
56k
-50
dBc
22k
-80
dBc
56k
-80
dBc
15
2014/10
[AK1220]
12. Typical Evaluation Board Schematic
VSS
Current Adjustment Resistor
22 to 56k
BIAS
AK1220
LO Input
50
100pF
VSS
RF Input
LOINP
LO Buffer
Iref
10nF
100pF
LOINN
100pF
IFOUTP
Mixer
C1
VDD
(Powefeeding for Open-drain
Output)
RFIN
Output Load
Resistor
RLoad
VSS
BALUN
IF Output
IFOUTN
L1
VDD
RF Input
Impedance Matching
VSS
IF Output
Impedance Matching
100pF
VSS
10nF
VDD
VSS
Figure 11. Typical Evaluation Board Schematic
Note 1) The open drain output needs power feeding via a inductor. (IFOUTP pin and IFOUTN)
Note 2) It is necessary to adjust impedance matching as to its setting frequency. (RF input and IF output)
MS1165-E-03
16
2014/10
[AK1220]
2. Example of impedance matching
・RFIN
RF Input
C1
RFIN
AK1220
L1
Frequency[MHz]
C1[pF]
L1[nH]
150
18
82
450
6
22
600
10
15
900
5
6.8
Frequency[MHz]
C1[pF]
L1[nH]
150
18
82
Start 50MHz, Stop 1GHz
Marker 1
1
150MHz: 43.0
-3.9
Figure 12. RFIN 150MHz example of impedance matching
MS1165-E-03
17
2014/10
[AK1220]
Frequency[MHz]
C1[pF]
L1[nH]
450
6
22
Start 50MHz, Stop 1GHz
1
Marker 1
2
380MHz: 27.5
3
-12.2
Marker 2
450MHz: 46.5
-10.2
Marker 3
570MHz: 52.5
-35.4
Figure 13. RFIN 450MHz example of impedance matching
Frequency[MHz]
C1[pF]
L1[nH]
600
10
15
Start 50MHz, Stop 1GHz
1
Marker 1
600MHz: 72.3
5.9
Figure 14. RFIN 600MHz example of impedance matching
MS1165-E-03
18
2014/10
[AK1220]
Frequency[MHz]
C1[pF]
L1[nH]
900
5
6.8
Start 50MHz, Stop 1GHz
1
Marker 1
900MHz: 42.9
16.3
Figure 15. RFIN 900MHz example of impedance matching
MS1165-E-03
19
2014/10
[AK1220]
・IFOUT
VDD
(Powefeeding for Open-drain Output)
10nF
100pF
Output Load Resistor
RLoad
AK1220
VSS
IFOUTP
R1
BALUN
IF Output
L2
C2
IFOUTN
L3
VSS
Frequency [MHz]
R1 [k]
C2 [pF]
L2 [nH]
L3 [nH]
30
2.2
3.9
1800
1800
50
2.2
2.0
1000
1000
60
2.2
0.5
1000
1000
80
2.2
N/A
680
680
470nH : Murata LQW21HNR47J00L
100
2.2
N/A
470
470
BALUN:Mini-Circuits ADT4-6T+
1800nH : Murata LQW21HN1R8J00L
1000nH : Murata LQW21HN1R0J00L
680nH : Murata LQW21HNR68J00L
Frequency [MHz]
R1 [k]
C2 [pF]
L2 [nH]
L3 [nH]
30
2.2
3.9
1800
1800
3
Start 10MHz, Stop 140MHz
2
Marker 1
28MHz: 52.5
1
-35.7
Marker 2
30MHz: 53.0
-24.1
Marker 3
36MHz: 75.6
34.1
Figure 16. IFOUT 30MHz example of impedance matching
MS1165-E-03
20
2014/10
[AK1220]
Frequency [MHz]
R1 [k]
C2 [pF]
L2 [nH]
L3 [nH]
50
2.2
2
1000
1000
3
Start 10MHz, Stop 140MHz
2
Marker 1
45MHz: 36.7
1
-26.9
Marker 2
50MHz: 40.9
-11.0
Marker 3
60MHz: 77.2
33.9
Figure 17. IFOUT 50MHz example of impedance matching
Frequency [MHz]
R1 [k]
C2 [pF]
L2 [nH]
L3 [nH]
60
2.2
0.5
1000
1000
Start 10MHz, Stop 140MHz
3
2
Marker 1
1
55MHz: 43.5
-32.0
Marker 2
60MHz: 50.5
-20.6
Marker 3
70MHz: 98.9
-6.1
Figure 18. IFOUT 60MHz example of impedance matching
MS1165-E-03
21
2014/10
[AK1220]
2
Frequency [MHz]
R1 [k]
C2 [pF]
L2 [nH]
L3 [nH]
80
2.2
N/A
680
680
Start 10MHz, Stop 140MHz
3
Marker 1
1
72MHz: 32.1
-21.9
Marker 2
80MHz: 45.5
-9.3
Marker 3
92MHz: 98.3
-10.2
Figure 19. IFOUT 80MHz example of impedance matching
Frequency [MHz]
R1 [k]
C2 [pF]
L2 [nH]
L3 [nH]
100
2.2
N/A
470
470
Start 10MHz, Stop 140MHz
2
Marker 1
1
92MHz: 26.3
-8.9
Marker 2
100MHz: 37.5
1.9
Figure 20. IFOUT 100MHz example of impedance matching
MS1165-E-03
22
2014/10
[AK1220]
・LOINP/LOINN
LO Input
50ohm
100pF
VSS
LOINP
LOINN
AK1220
100pF
Figure 21. LOINP/LOINN example of impedance matching
MS1165-E-03
23
2014/10
[AK1220]
13. IC Interface Schematic
No.
Name
I/O
Function
1
RFIN
I
RF input pin
3
LOINN
I
Lo input pins
4
LOINP
I
27kohm
8
BIAS
I/O
Analog I/O pin
300ohm
11
IFOUTN
O
12
IFOUTP
O
IF output pins
IFOUTP
IFOUTN
MS1165-E-03
24
2014/10
[AK1220]
14. Application Information
•Impedance matching network with LC
Figure 22. Impedance matching network with LC
Impedance matching network with LC is shown in Figure 22. AK1220 has open drain outputs, so RL1 + RL2 is
output load resistance. C11 and L11 compose lowpass filter. C12 and L12 are for highpass filter. C13 is DC
blocking capacitor and L13 is RF choke. IFOUTP and IFOUTN pins need power feeding via L11, L12 and L13.
The differential voltage from IFOUTP/N can be converted to a single-ended by L11, L12, C11 and C12 properly.
The differential impedance (RL1 + RL2) is converted to single-ended output terminating impedance Ro.
L11, C11, L12 and C12 are calculated as below. fout is IF output frequency.
C11  C12 
L11  L12 
1
2π * f OUT * RL1  RL2 * RO
RL1  RL2 * RO
2π * f OUT
For example, in the case of IF Output = 50MHz, Output Load Resistor (Rload) = 2.2k in 50 interface, L11,
C11, L12 and C12 are calculated as below.
MS1165-E-03
25
2014/10
[AK1220]
C11  C12 
1
 9.6pF
2π * 50 *10^6* 2.2 *10^3* 50
L11  L12 
2.2 *10^3* 50
 1056nH
2π * 50 *10^6
L13 and C13 should be large enough not to affect the impedance at IF output frequency. In some cases the
impedance matching can be optimized by L13 and C13.
For example, in the case of IF Output = 50MHz, Output Load Resistor (Rload) = 2.2k in 50 interface, it is
recommended to choose 2200nH and 1000pF as L13 and C13. If any correction is needed, it can be adjusted
by reducing the value of L13 and C13.
These calculated values are approximation. In some cases, some correction is needed due to the effect of
parasitic capacitance of external parts or/and PCBs. The impedance matching network components should be
decided through enough evaluation on AK1220.
Typical Performance using impedance matching network with LC is below. RF Input = 600MHz, IF Output =
50MHz, LO Input = 550MHz, Output Load Resistor (Rload) = 2.2k, Vdd = 5V, Ta = 25C, LO Input Level =
0dBm,
MS1165-E-03
Ref.
Value
Size
Part Number
RL1, RL2
1.1k
1005
KOA RK73K1ETP112
L11, L12
1000nH
2012
Murata LQW21HN1R0J00
C11, C12
10pF
1005
Murata GRM1552C1H100JA01
L13
2200nH
2012
Murata LQW21HN2R2J00
C13
120pF
1005
Murata GRM1552C1H121JA01
26
2014/10
[AK1220]
Parameter
Rbias
Min.
Typ.
Rbias = 22k (17mA)
0.7
Rbias = 56k (9mA)
0.0
SSB Noise Figure
Rbias = 22k (17mA)
11.3
(NF)
Rbias = 56k (9mA)
10.1
Rbias = 22k (17mA)
6.0
Rbias = 56k (9mA)
1.5
Rbias = 22k (17mA)
22.1
Rbias = 56k (9mA)
13.8
Conversion Gain
Max.
Unit
dB
dB
IP1dB
dBm
IIP3
dBm
The phase and amplitude balance is achieved at IF Output frequency by using impedance matching network with
LC. The port-to-port leakage is improved with the phase and amplitude balance is achieved at RF, LO, and IF
frequency with wide band balun.
MS1165-E-03
27
2014/10
[AK1220]
・Evaluation Board
Figure 23. AK1220/AK1222 Evaluation Board (Balun)
Figure 24. AK1220/AK1222 Evaluation Board Schematic (Balun)
MS1165-E-03
28
2014/10
[AK1220]
Figure 25. AK1220/AK1222 Evaluation Board (matching network with LC)
Figure 26. AK1220/AK1222 Evaluation Board Schematic (matching network with LC)
MS1165-E-03
29
2014/10
[AK1220]
15. Outer Dimensions
1 pin marking
(Note 1)
0.58±0.05
3.0±0.10
3.0±0.10
1
4
16
5
13
8
9
12
Figure 27. Outer Dimensions
Note 1. 1 pin marking is only a reference for the 1 pin location on the top of package.
MS1165-E-03
30
2014/10
[AK1220]
16. Marking
(a) Style
:
QFN
(b) Number of pins
:
16
(c) 1 pin marking:
:
○
(d) Product number
:
1220
(e) Date code
:
YWWL (4 digits)
Y:
Lower 1 digit of calendar year (Year 2010 → 0, 2011 → 1 ...)
WW:
Week
Lot identification, given to each product lot which is made in a week
 LOT ID is given in alphabetical order (A, B, C…).
1 2 2 0(d)
YWWL (e)
(c)
Figure 28. Marking
MS1165-E-03
31
2014/10
[AK1220]
IMPORTANT NOTICE
0. Asahi Kasei Microdevices Corporation (“AKM”) reserves the right to make changes to
the information contained in this document without notice. When you consider any use
or application of AKM product stipulated in this document (“Product”), please make
inquiries the sales office of AKM or authorized distributors as to current status of the
Products.
1. All information included in this document are provided only to illustrate the operation
and application examples of AKM Products. AKM neither makes warranties or
representations with respect to the accuracy or completeness of the information
contained in this document nor grants any license to any intellectual property rights
or any other rights of AKM or any third party with respect to the information in this
document. You are fully responsible for use of such information contained in this
document in your product design or applications. AKM ASSUMES NO LIABILITY
FOR ANY LOSSES INCURRED BY YOU OR THIRD PARTIES ARISING FROM THE
USE OF SUCH INFORMATION IN YOUR PRODUCT DESIGN OR APPLICATIONS.
2. The Product is neither intended nor warranted for use in equipment or systems that
require extraordinarily high levels of quality and/or reliability and/or a malfunction or
failure of which may cause loss of human life, bodily injury, serious property damage
or serious public impact, including but not limited to, equipment used in nuclear
facilities, equipment used in the aerospace industry, medical equipment, equipment
used for automobiles, trains, ships and other transportation, traffic signaling
equipment, equipment used to control combustions or explosions, safety devices,
elevators and escalators, devices related to electric power, and equipment used in
finance-related fields. Do not use Product for the above use unless specifically agreed
by AKM in writing.
3. Though AKM works continually to improve the Product’s quality and reliability, you
are responsible for complying with safety standards and for providing adequate
designs and safeguards for your hardware, software and systems which minimize risk
and avoid situations in which a malfunction or failure of the Product could cause loss
of human life, bodily injury or damage to property, including data loss or corruption.
4. Do not use or otherwise make available the Product or related technology or any
information contained in this document for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear,
chemical, or biological weapons or missile technology products (mass destruction
weapons). When exporting the Products or related technology or any information
contained in this document, you should comply with the applicable export control laws
and regulations and follow the procedures required by such laws and regulations. The
Products and related technology may not be used for or incorporated into any products
or systems whose manufacture, use, or sale is prohibited under any applicable
domestic or foreign laws or regulations.
5. Please contact AKM sales representative for details as to environmental matters such
as the RoHS compatibility of the Product. Please use the Product in compliance with
all applicable laws and regulations that regulate the inclusion or use of controlled
substances, including without limitation, the EU RoHS Directive. AKM assumes no
liability for damages or losses occurring as a result of noncompliance with applicable
laws and regulations.
6. Resale of the Product with provisions different from the statement and/or technical
features set forth in this document shall immediately void any warranty granted by
AKM for the Product and shall not create or extend in any manner whatsoever, any
liability of AKM.
7. This document may not be reproduced or duplicated, in any form, in whole or in part,
without prior written consent of AKM.
MS1165-E-03
32
2014/10
Related Parts
Part#
Discription
Comments
AK1220
100MHz~900MHz High Linearity Down Conversion Mixer
IIP3:+22dBm
AK1222
100MHz~900MHz Low Power Down Conversion Mixer
IDD:2.9mA
AK1224
100MHz~900MHz Low Noise, High Liniarity Down Conversion Mixer
NF:8.5dB, IIP3:+18dBm
AK1228
10MHz~2GHz Up/Down Conversion Mixer
3V Supply, NF:8.5dB
AK1221
0.7GHz~3.5GHz
IIP3:+25dBm
AK1223
3GHz~8.5GHz High Linearity Down Conversion Mixer
Mixer
High Linearity Down Conversion Mixer
IIP3:+13dB, NF:15dB
PLL Synthesizer
AK1541
20MHz~600MHz Low Power Fractional-N Synthesizer
IDD:4.6mA
AK1542A
20MHz~600MHz Low Power Integer-N Synthesizer
IDD:2.2mA
AK1543
400MHz~1.3GHz Low Power Fractional-N Synthesizer
IDD:5.1mA
AK1544
400MHz~1.3GHz Low Power Integer-N Synthesizer
IDD:2.8mA
AK1590
60MHz~1GHz Fractional-N Synthesizer
IDD:2.5mA
AK1545
0.5GHz~3.5GHz Integer-N Synthesizer
16-TSSOP
AK1546
0.5GHz~3GHz Low Phase Noise Integer-N Synthesizer
Normalized C/N:-226dBc/Hz
AK1547
0.5GHz~4GHz Integer-N Synthesizer
5V Supply
AK1548
1GHz~8GHz Low Phase Noise Integer-N Synthesizer
Normalized C/N:-226dBc/Hz
100~300MHz Analog Signal Control IF VGA w/ RSSI
Dynamic Range:30dB
IFVGA
AK1291
integrated VCO
AK1572
690MHz~4GHz Down Conversion Mixer with Frac.-N PLL and VCO
IIP3:24dBm, -111dBc/Hz@100kHz
AK1575
690MHz~4GHz Up Conversion Mixer with Frac.-N PLL and VCO
IIP3:24dBm, -111dBc/Hz@100kHz
IF Reciever (2nd Mixer + IF BPF + FM Detector)
AK2364
Built-in programmable AGC+BPF, FM detector IC
IFBPF:10kHz ~ 4.5kHz
AK2365A
Built-in programmable AGC+BPF, IFIC
IFBPF:7.5kHz ~ 2kHz
Analog BB for PMR/LMR
AK2345C
AK2360/
AK2360A
CTCSS Filter, Encoder, Decoder
24-VSOP
Inverted frequency(3.376kHz/3.020kHz) scrambler
8-SON
AK2363
MSK Modem/DTMF Receiver
24-QFN
AK2346B
0.3-2.55/3.0kHz Analog audio filter,
Emphasis, Compandor, scrambler, MSK Modem
24-VSOP
0.3-2.55/3.0kHz Analog audio filter
Emphasis, Compandor, scrambler, CTCSS filter
24-VSOP
AK2346A
AK2347B
AK2347A
24-QFN
24-QFN
Function IC
AK2330
8-bit 8ch Electronic Volume
VREF can be selected for each
channel
AK2331
8-bit 4ch Electronic Volume
VREF can be selected for each
channel
Asahi Kasei Microdevices Corporation (“AKM”) reserves the right to make changes to the information contained in this document
without notice. When you consider any use or application of AKM product stipulated in this document, please make inquiries the
sales office of AKM or authorized distributors as to current status of the Products.
2014/10