Si9731 Datasheet

Product is End of Life 12/2014
Si9731
Vishay Siliconix
µP Controlled Battery Charger
for 1-Cell Li-ion or 1-Cell to 3-Cell NiCd/NiMH Batteries
DESCRIPTION
FEATURES
Si9731 is a chemistry independent battery charger designed
to pulse charge 1-cell to 3-cell NiCd/NiMH or 1-cell Li-ion
batteries. Battery charging is accomplished under direct
control from the system processor. An internal low RDS(on)
MOSFET can be pulsed on and off at varying duty cycle by
the system processor to pulse charge the battery at high
charge current while minimizing heat dissipation. Provision is
also made to trickle charge a discharged battery until the
battery is charged to a high enough voltage to wake up the
processor so that the processor can take control of the
charging process. For charging Li-ion batteries, Si9731
includes a precision voltage reference and an error amplifier
for constant voltage (CV) charge mode. The Si9731 is
available in lead (Pb)-free TSSOP-16 package and is
classified over the industrial temperature range (- 40 °C to
+ 85 °C).
• Pulse charges 1-cell Li-ion or 1-cell to 3-cell
NiCd/NiMH batteries
• Integrated MOSFETs with bi-directional
reverse current blocking in "OFF" mode
• PWM controlled fast charging mode
• Low current trickle charge mode
• Pin selectable 4.1 V or 4.2 V charge termination for Li-ion
• Constant voltage (CV) termination for Li-ion
• Input over-voltage detector with automatic shutdown
• External shutdown
• Under 1 µA reverse battery leakage current in shutdown
• Complete isolation from battery to external power supply
in shutdown
• Thermal shutdown
• Minimum number of external components
• ESD protection to 4 kV on charger input and battery
output
• TSSOP-16 package (1.2 mm maximum height)
• Halogen-free according to IEC 61249-2-21 definition
• Compliant to RoHS directive 2002/95/EC
APPLICATIONS
• Cellular phone battery charger
• Personal digital assistants
FUNCTIONAL BLOCK DIAGRAM
VBAT
VCHARGER
ON/OFF
Fast
Charge
Trickle
Charge
B
a
t
t
e
r
y
TRICKLECHARGEENABLE
CVMODE
Charge Control
4.1/4.2 V_TAP
FAST CHARGE
GND
Document Number: 71321
S09-2249Rev. C, 26-Oct-09
www.vishay.com
1
Si9731
Vishay Siliconix
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Limit
Unit
- 0.3 to 13.5
V
1.2
A
5
mA
Voltages Referenced to GND = 0 V
VCHARGER, V(CVMODE), V(TRICKLECHARGEEN), V(MAINCHARGEREN), V(ON/OFF),
V(4.1 V_TAP), V(VBAT+), V(CHARGERPOWER_ON), V(CHARGERPRESENT),
V(TRICKLE_VBAT)
V(CHARGERPRESENTIN), V(CHARGERPOWER_ONIN)
Maximum Input Current (ICHARGER(max))
Maximum Sink Current
CHARGERPOWER_ON and CHARGERPRESENT Pins
Storage Temperature
- 65 to 150
Operating Junction Temperature
°C
150
Power Dissipation (Package)a
16-Pin TSSOP (Q Suffix)b
1.06
W
Thermal Impedance (ΘJA)
16-Pin TSSOP
135
°C/W
Notes:
a. Device Mounted with all leads soldered or welded to PC board.
b. Derate 10 mW/°C above 25 °C.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING RANGE
Parameter
Symbol
Limit
Unit
Voltages Referenced to GND = 0 V
VCHARGER
Ambient Temperature
3.0 to 12
V
- 40 to + 85
°C
VREFBypass Capacitor
0.1
COUT
2.2
CIN
2.2
µF
See application drawing Figure 1.
SPECIFICATIONS
Parameter
External Charger Voltage
Under Voltage Lockout on Charger
UVLO Hysteresis
Symbol
VUVLO
Rising Edge of Battery Charger
2.45
Regulated Output Voltage 4.1 V_TAP Open
Battery Over Voltage Protection
VOVP
Battery Over Voltage Hysteresis
VOVP_HYS
Battery Minimum Operating Voltage
VBAT(min)
Charger Voltage to Battery Voltage
Comparator Offset
VOS_CB
Typ.b Max.a
3.0
UVLOHYST
VTERM+
www.vishay.com
2
Min.a
VCHARGER
Regulated Output Voltage 4.1 V_TAP to VBAT
Charger Voltage to Battery Voltage
Comparator Hysteresis
Test Conditions Unless Specified
- 40 °C < TA < + 85 °C
3.0 V ≤ VCHARGER ≤ 6.5 V, VON/OFF = 1.5 V
VCHARGER = 5.0 V
IBAT+ = 1 mA
MAINCHARGEREN
= 5.0 V
CVMODE = 5.0 V
12
2.6
2.75
70
90
110
- 10 °C < TA < + 40 °C
4.050
4.1
4.150
- 40 °C < TA < + 85 °C
4.025
4.1
4.150
- 10 °C < TA < + 40 °C
4.150
4.2
4.250
- 40 °C < TA < + 85 °C
4.125
4.2
4.250
4.95
5.15
Rising Edge of VBAT+
4.70
Comparator
Offset Voltage,
VCHARGER - VBAT+
MAINCHARGEEN-High
MAINCHARGEEN-Low
3.12
3.24
V
mV
V
0.11
Rising Edge, VBAT+ Latch
Unit
3.33
- 0.08 - 0.04 - 0.01
0.01
0.04
0.08
0.07
Document Number: 71321
S09-2249Rev. C, 26-Oct-09
Si9731
Vishay Siliconix
SPECIFICATIONS
Parameter
Symbol
Test Conditions Unless Specified
- 40 °C < TA < + 85 °C
3.0 V ≤ VCHARGER ≤ 6.5 V, VON/OFF = 1.5 V
Min.a
Typ.b Max.a
Unit
Quiescent Current (Normal Mode)
IIN(VCHARGER Pin)
ON-Mode
1 mA ≤ IBAT+ ≤ 600 mA
1
3
mA
Quiescent Current (Shutdown Mode)
IIN(VCHARGER Pin)
OFF-Mode
VON/OFF = 0 V, VCHARGER = 4.5 V
0.1
1
µA
RFB1
Pin 12 to Pin 14
1
RFB2 + RFB3
Pin 12 to GND
41
Feedback Resistor
IPIN13 + IPIN14
Battery Leakage Current
Q1 ON Resistance
Q1 RDS(on)
Q2 ON Resistance
Q2 RDS(on)
Q5 ON Resistancec
Q5 RDS(on)
Over Voltage Detect Threshold
VCHARGER(OVD)
Over Voltage Detect Threshold Hysteresis
VCHARGER(OVD)
CHARGERPRESENT and
CHARGERPOWER_ON
VBAT+ = 4.2 V
VON/OFF = 0 V
-1
0.1
1
VCHARGER = 0 V
-1
0.1
2
MAINCHARGEREN
≥ 1.5 V
VCHARGER = 4.5 V
400
TRICKLECHARGEEN
≤ 0.4 V
6
CVMODE ≥ 1.5 V
6
Rising Edge of Battery Charger
12.0
12.8
IOH
VOH = 6.5 V
Output Low
Voltage
VOL
IOL = 1 mA
Logic Low
Voltage
VIL
Logic High
Voltage
VIH
Pull Down
Current
IP/D
0.7
TS/D
130
THYST
10
Thermal Shutdown Temperaturec
Thermal Shutdown Hysteresis
c
Shutdown High Voltage Logic Level
VON/OFF(high)
Shutdown Low Voltage Logic Level
VON/OFF(low)
Shutdown Hysteresis
VON/OFF(hyst)
10
0.1
µA
mΩ
Ω
13.4
V
0.4
_HYS
Output High
Leakage
Current
CHARGERPRESENTIN,
CHARGERPOWER_ONIN,
TRICKLECHARGEEN,
MAINCHARGEEN or
CVMODE
kΩ
2
µA
0.4
0.4
V
10
µA
1.5
°C
1.5
0.3
100
V
mV
Notes:
a. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
b. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing.
c. Guaranteed by design and characterization, not subject to production testing.
Document Number: 71321
S09-2249Rev. C, 26-Oct-09
www.vishay.com
3
Si9731
Vishay Siliconix
PIN CONFIGURATION
TSSOP-16
CHARGERPRESENTIN
1
16
CHARGERPRESENT = (XCHARGERPRESENT)
CHARGERPOWER_ONIN
2
15
CHARGERPOWER_ON = (XCHARGERPOWER_ON)
VCHARGER
3
14
VBAT+
ON/OFF
4
13
TRICKLE_VBAT
TRICKLECHARGEEN
5
12
4.1 V_TAP
CVMODE
6
11
GND
MAINCHARGEEN
7
10
(N/C)
(N/C)
8
9
VREF
Si9731DQ
Top View
ORDERING INFORMATION
Part Number
Temperature Range
Package
Si9731DQ-T1-E3
- 40 to 85 °C
Tape and Reel
PIN DESCRIPTION
Pin Number
Name
1
CHARGERPRESENTIN
2
Function
Logic input for CHARGERPRESENT output
CHARGERPOWER_ONIN Logic input for CHARGERPOWER_ON output
3
VCHARGER
4
ON/OFF
5
TRICKLECHARGEEN
6
CVMODE
7
MAINCHARGEEN
External charger
Master shutdown pin. Taking ON/OFF low shuts down the charger and quiescent current drops
to under 1 µA
Taking this pin high disables trickle (slow) charging
A logic high enables the error amplifier to linearly drive the gate of MOSFET Q1 when
MAINCHARGEREN is high.
An external PWM signal at MAINCHARGEREN pin controls the ON/OFF duty cycle of the Fast
Charge MOSFET, Q1.
8, 10
N/C
Do not connect external circuitry to this pin. Circuitry internal to the IC is connected to this pin.
9
VREF
Internal 1.30 V precision bandgap reference voltage. Do not apply loads to this pin.
11
GND
Low impedance system ground
12
4.1 V_TAP
Connect this pin to VBAT+ for 4.1 V charge termination in constant voltage mode
13
TRICKLE_VBAT
Resistor connected between this pin and VBAT to limit the trickle charge current.
14
VBAT+
15
CHARGERPOWER_ON
Open drain logic output
16
CHARGERPRESENT
Open drain logic output
www.vishay.com
4
Charger output connected to battery’s positive terminal
Document Number: 71321
S09-2249Rev. C, 26-Oct-09
Si9731
Vishay Siliconix
TABLE 1: BATTERY CHARGING CONTROL LOGIC Nominal Voltage Values
VCHARGER
TRICKLE
CHARGEEN
CVMODE
MAIN
CHARGEEN
ON/OFF
Q1b
Q2
X
X
X
X
OFF
OFF
Not Charging
X
X
X
X
OFF
OFF
Not Charging
X
X
X
X
OFF
OFF
Not Charging
Not Charging (Shutdown)
Not Present
Not Present
OK to Chargea
Over Voltage
VCHARGER > 12.8 V
Present
OK to Chargea
Mode
X
X
X
LOW
OFF
OFF
LOW
LOW
LOW
HIGH
OFF
ON
Trickle Charge
OFF
Not Charging
(Current pulse off during Constant
Current Charge)
HIGH
LOW
LOW
HIGH
OFF
LOW
LOW
HIGH
HIGH
ON
OFF
HIGH
LOW
HIGH
HIGH
ON
OFF
LOW
HIGH
LOW
HIGH
OFF
OFF
HIGH
HIGH
LOW
HIGH
OFF
OFF
LOW
HIGH
HIGH
HIGH
ON
OFF
HIGH
HIGH
HIGH
HIGH
ON
OFF
Constant Current Charge
(current pulse on)
Not Charging
(Current pulse off during Constant
Current Charge with output limited
to 4.1 V/4.2 V or end of charge in Li-Ion
charging)
Constant Current Charge
(Output Limited to 4.1 V/4.2 V or
Constant Voltage Charge)
Notes:
a. "OK to Charge" is a flag signal that is enabled by satisfying all the following conditions:
1. Battery voltage is below 5 V
2. Charger voltage is greater than 3 V but below 12.8 V
3. If MAINCHARGEEN = Logic Low, VCHARGER > VBAT + 40 mV,
If MAINCHARGEEN = Logic High, VCHARGER > VBAT - 40 mV
4. ON/OFF pin is at logic high.
b. Q1 drive is determined by the error amplifier during constant voltage mode.
Q1 drive is a combination of Q1 drive (digital) and the output of the error amplifier using the analog adder. The combinations are:
TABLE 2
Q1 Drive (Digital)
Output of Error Amplifier
Q1 Drive
LOW
LOW
LOW (fully off)
Intermediate (linear mode)
LOW
Intermediate
HIGH
LOW
HIGH (fully on)
HIGH
HIGH
Should Never Happen
Document Number: 71321
S09-2249Rev. C, 26-Oct-09
www.vishay.com
5
Si9731
Vishay Siliconix
TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted
4.22
4.22
4.1 TAP Open
4.1 TAP Open
4.20
4.20
4.18
4.18
V BAT - (V)
V BAT - (V)
4.16
4.16
4.14
4.12
4.14
4.12
4.1 TAP to VBAT
4.10
4.1 TAP to VBAT
4.10
4.08
4.08
3
6
9
4.06
- 40
12
- 15
10
VCHARGER (V)
1.0
VCHARGER = 0 V
VBAT = 4.2 V
2.70
0.8
Current V BAT - (V)
VCHARGER - (V)
85
Temperature (°C)
2.75
2.65
2.60
2.55
0.6
0.4
0.2
2.50
www.vishay.com
6
60
VBAT (CV Mode) vs. Temperature
VBAT (CV Mode) vs. VCHARGER
2.45
- 40
35
- 15
10
35
60
85
0.0
- 40
- 20
0
20
40
60
Temperature (°C)
Temperature (°C)
Charger UVLO Rising vs. Temperature
VBAT Leakage vs. Temperature
80
100
Document Number: 71321
S09-2249Rev. C, 26-Oct-09
Si9731
Vishay Siliconix
BLOCK DIAGRAM AND TYPICAL APPLICATION CIRCUIT
16
CHARGERPRESENTIN
1
Q3
15
CHARGERPOWER_ONIN
CHARGERPRESENT
2
CHARGERPOWER_ON
Q4
Latch
ON/OFF
4
1 MΩ
100 kΩ
Battery Min Voltage
VCHARGER
–
UVL
3
+
2.6 V
3.4 V
+
Circuit
Power
–
14
+
CIN
2.2 μfd
OVP
OK to Charge
(OTC)
–
12.8 V
VBAT+
VBAT
5V
–
COUT
2.2 μfd
Battery Over
Voltage
+
56 Ω
+
B
a
t
t
e
r
y
–
13
Q2
Trickle_VBAT
Trickle
Charge
Q1
Fast
Charge
RFB1
12
TRICKLECHARGEEN
4.1 V_TAP
RFB2
5
RFB3
CVMODE
6
Digital
+
Q5
11
Enable
MAINCHARGEEN
GND
7
Voltage
Generator
2.6 V
3.4 V
5V
12.8 V
Temp
OK
–
Analog
Temp
Sensor
9
+
VREF
E/A
Ref
Voltage
8
N/C
0.1 μfd
1.3 V
10
N/C
Figure 1.
Document Number: 71321
S09-2249Rev. C, 26-Oct-09
www.vishay.com
7
Si9731
Vishay Siliconix
DETAIL OPERATIONAL DESCRIPTION
Si9731 is a chemistry independent battery charger designed
for use with a system processor. For example, Si9731 can be
integrated within a cellular phone whereby the fast charge
and trickle (slow) charge modes can be software controlled
by the DSP. The device is designed to charge 1-cell Li-ion or
1-cell to 3-cell NiCd/NiMH batteries. A regulated or
unregulated external dc power source such as a wall adapter
rated at typically 4.5 V to 12 V is connected to Si9731’s
VCHARGER input pin. Note that a typical low cost wall adaptor
is comprised of a transformer, bridge rectifier and a reservoir
capacitor. The wall adaptor’s output voltage decreases
linearly with increase in output current. When Si9731 is fast
charging the battery, the wall adaptor’s output voltage tracks
the battery voltage plus the voltage drop across Q1 (charging
current times MOSFET Q1’s RDS(on), see Figure 1). The key
features of Si9731 are described below.
Since the under voltage lock out (UVLO) point of Si9731 is
2.6 V (typical), it is essential to keep the charger voltage
above this level under all conditions, especially for fast
charging of single cell NiCd/NiMH. One simple solution is
adding a external resistor between VBAT+ pin and the battery,
which creates extra voltage drop to elevate the charger
voltage. The value of the resistor is affected by the output
V-I characteristic of the ac charger.
Trickle Charge
The charge path is via N-Channel MOSFETs Q1 or Q2 (see
applications circuit of Figure 1). Si9731 defaults to trickle
(slow) charge mode if the battery voltage is too low to power
the main processor. With the main processor unable to drive
the
MAINCHARGEEN
pin
as
well
as
the
TRICKLECHARGEEN pins, Q1 is turned "OFF" preventing
fast charging. Meanwhile N-Channel MOSFET Q2 turns
"ON" and establishes a trickle charge path from the external
power source VCHARGER to the battery. The trickle charge
current is set by an external current limiting resistor, Rext, and
is approximately ITRICKLE = (VCHARGER - VBAT+)/Rext. Once
the battery voltage charges up to minimum battery operating
voltage 3.24 V, the internal latch is triggered and the
CHARGERPOWER_ON output changes state to wake up
the processor. The processor is now able to disable trickle
charge mode by taking the TRICKLECHARGEEN pin high
while taking control of fast charging via the
MAINCHARGEEN pin.
www.vishay.com
8
Fast Charge
Fast charging is accomplished by the low "ON" resistance
MOSFET, Q1. The application microprocessor is able to
"Pulse Charge" the battery via the MAINCHARGEREN
control input of Si9731. The processor monitors the battery
voltage via the system A/D converter and varies the pulse
charging duty cycle accordingly to maintain fast charging.
Note that even though charging current may be sufficiently
high, pulse charging with short "ON" time and long "OFF"
time ensures that heat generation due to thermal heating is
reduced.
In the case of NiCd or NiMH batteries, one of several charge
termination schemes may be used to terminate charge. For
example, the processor may disable fast charging by
sensing ΔV or dV/dt at the VBAT+ output or by monitoring the
temperature differential ΔT of the battery. Following fast
charge, trickle charge may be enabled to "top off" the battery.
When charging a 1-cell Li-ion battery, fast charging will
operate in two modes, constant current mode followed by
constant voltage mode. In the constant current mode, a
discharged Li-ion battery is charged with constant current
available from the external dc source. The MOSFET pass
transistor (Q1) may be pulsed "ON" and "OFF" at varying
duty cycle by the control signal present at the
MAINCHARGEEN input pin. Once the battery voltage
reaches it’s termination voltage of 4.1 V or 4.2 V (depending
on the connection of the 4.1 VTAP), Si9731 may be placed in
the "Constant Voltage" charging mode by taking the
CVMODE pin high. Taking CVMODE pin high disables trickle
charging and enables the internal battery voltage divider by
turning ON Q5. Then the error amplifier will compare divided
VBAT+ voltage against an internal precision 1.3 V bandgap
reference voltage (see Figure 1). The output of the error
amplifier drives the pass transistor Q1 to maintain VBAT+ at
the regulated termination voltage. This operation is same as
a linear regulator.
True Load Disconnect
Both the fast charge FET (Q1 in Figure 1) and trickle charge
FET (Q2 in Figure 1) incorporate a floating body diode. In
their "OFF" state both FETs block current bidirectionally.
Note that because of the reverse blocking switches, a
Schottky diode in series with the external VCHARGER power
supply is not required.
Document Number: 71321
S09-2249Rev. C, 26-Oct-09
Si9731
Vishay Siliconix
DETAIL OPERATIONAL DESCRIPTION
4.1 VTAP
Thermal Shutdown
The Si9731’s internal feedback resistors are set to provide
4.2 V charge termination at VBAT+ output if the 4.1 VTAP is left
open circuit. Connecting the 4.1 VTAP to VBAT+ configures
Si9731 for 4.1 V charge termination at VBAT+. This feature
allows Si9731 to accommodate Li-ion batteries requiring
4.1 V or 4.2 V charge termination. Caution: the 4.1 VTAP
should not be connected to ground or any other voltage
source as this will cause the Si9731 to operate open loop and
can result in over charging the battery!
Si9731 also includes a thermal protection circuit that
suspends charging through Q1 and Q2 when die
temperature exceeds 130 °C due to overheating. Once the
die temperature cools to below 120 °C, the charging will
resume.
Feedback Disconnect Switch
The Si9731 includes a feedback disconnect switch (Q5 in
Figure 1) connected in series with the device’s internal
feedback resistor string. The 42 kΩ feedback resistor string
is connected to ground when both the internal "OK to
Charge" signal and the CVMODE pin are at logic high,
providing feedback voltage to Si9731’s error amplifier. This
action helps prevent the Si9731 from discharging the battery.
CHARGERPRESENT and CHARGERPOWERON
Shutdown
Si9731 can be completely turned off by applying 0.4 V or less
to the device’s ON/OFF pin. In shutdown mode, Si9731
draws less than 1 µA quiescent current with charger voltage
below UVLO, and draws 500 µA when charger voltage is
above UVLO. The device is enabled by applying 1.5 V to
12 V at the ON/OFF pin. In applications where the device will
always remain enabled, the ON/OFF pin may be connected
to the VCHARGER pin. Si9731’s shutdown circuitry includes
hysteresis, as such the device will operate properly even if a
slow moving signal is applied to the ON/OFF pin. When the
device is enabled, the battery voltage sense circuitry draws
approximately 25 µA from VBAT.
OK to Charge (OTC)
CHARGERPRESENT and CHARGERPOWERON are open
drain outputs, each requiring an external pull-up resistor.
pin
goes
low
with
CHARGERPRESENT
CHARGERPRESENTIN pin goes high, signaling the
processor that a charger has been inserted.
Pin
goes
low
when
CHARGERPOWERON
CHARGERPOWERONIN Pin is high, charger voltage is not
in UVLO and the battery voltage has increased to above
3.24 V, turning on the system power supply since the battery
has been charged up to minimum operating voltage.
Input Over-Voltage Detector
The external dc source connected to the VCHARGER pin
should be at 12 V or less. In the unlikely event that the
voltage at VCHARGER pin is at or above 12.8 V (typical),
Si9731’s internal over voltage detector will turn off MOSFETs
Q1, Q2, and Q5 and disable charging.
Si9731 also includes an internal signal that enables both
trickle charge mode and fast charge mode operations, the
"OK to Charge" (or OTC) signal. The OTC signal is at logic
high if all of the following are satisfied:
1. Battery voltage is below 5 V
2. Charger voltage is greater than 2.6 V but below 12.8 V
3. VCHARGER > VBAT + 40 mV when MAINCHARGEEN =
Low
VCHARGER > VBAT - 40 mV when MAINCHARGEEN =
High
4. ON/OFF pin is at logic high.
In order to charge the battery in any manner, the OTC signal
has to be high.
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?71321.
Document Number: 71321
S09-2249Rev. C, 26-Oct-09
www.vishay.com
9
Package Information
Vishay Siliconix
TSSOP: 16-LEAD
DIMENSIONS IN MILLIMETERS
Symbols
Min
Nom
Max
A
-
1.10
1.20
A1
0.05
0.10
0.15
A2
-
1.00
1.05
0.38
B
0.22
0.28
C
-
0.127
-
D
4.90
5.00
5.10
E
6.10
6.40
6.70
E1
4.30
4.40
4.50
e
-
0.65
-
L
0.50
0.60
0.70
L1
0.90
1.00
1.10
y
-
-
0.10
θ1
0°
3°
6°
ECN: S-61920-Rev. D, 23-Oct-06
DWG: 5624
Document Number: 74417
23-Oct-06
www.vishay.com
1
PAD Pattern
www.vishay.com
Vishay Siliconix
RECOMMENDED MINIMUM PAD FOR TSSOP-16
0.193
(4.90)
0.171
0.014
0.026
0.012
(0.35)
(0.65)
(0.30)
(4.35)
(7.15)
0.281
0.055
(1.40)
Recommended Minimum Pads
Dimensions in inches (mm)
Revision: 02-Sep-11
1
Document Number: 63550
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000