REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add one vendor, CAGE 01295. Make changes to 1.3, table I, and editorial changes throughout. 90-06-13 M. A. FRYE B Drawing updated to reflect current requirements. - ro 05-06-01 R. MONNIN C Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 11-04-19 C. SAFFLE D Add device type 02 along with device class V and radiation hardened requirements. Add case outline H, descriptive designator GDFP1-F10 and paragraph 3.2.3. For device type 01, case outline X, correct power dissipation by deleting 115 mW and substituting with 52 mW as specified under paragraph 1.3. - ro 12-03-30 C. SAFFLE E Make correction to the Reverse breakdown voltage test as specified under Table I. For subgroups 2, 3, delete 2.460 V minimum, 2.535 V maximum and substitute 2.485 V minimum, 2.515 V maximum. - ro 13-05-30 C. SAFFLE F Add paragraph 3.1.1 and appendix A for microcircuit die. Correct the device type 02 junction temperature limits for case outlines H and X. Add new footnote 3/ to table I herein. - ro 14-06-23 C. SAFFLE G Add top metalization material, substrate material, and substrate potential information to figure A-1. - ro 14-10-16 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV G G G SHEET 15 16 17 REV STATUS REV G G G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil CHECKED BY RAY MONNIN APPROVED BY THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A WILLIAM J. JOHNSON DRAWING APPROVAL DATE 89-06-26 REVISION LEVEL G MICROCIRCUIT, LINEAR, VOLTAGE REFERENCE, 2.5 VOLT, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 5962-89610 1 OF 17 5962-E504-14 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 5962 - 89610 Federal stock class designator \ RHA designator (see 1.2.1) 01 X A Device type (see 1.2.2) Case outline (see 1.2.4) Lead finish (see 1.2.5) / \/ Drawing number For device class V: 5962 R 89610 Federal stock class designator \ RHA designator (see 1.2.1) 02 V X C Device type (see 1.2.2) Device class designator (see 1.2.3) Case outline (see 1.2.4) Lead finish (see 1.2.5) / \/ Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Temperature range 01 02 LT1009 RH1009 -55C to +125C -55C to +125C Circuit function Voltage reference diode Voltage reference diode 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q designators will not be included in the PIN and will not be marked on the device. Device class M Q or V Device requirements documentation Vendor self-certification to the requirements for MIL-STD-883 compliant, nonJAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Certification and qualification to MIL-PRF-38535 STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 2 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator X H See figure 1 GDFP1-F10 Terminals Package style 3 10 Can Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ Reverse current (IR) ..................................................................................................... 20 mA Forward current (IF) ...................................................................................................... Storage temperature range ........................................................................................... Lead temperature (soldering, 10 seconds) ................................................................... For device type 01 case outline X: Maximum power dissipation (PD) ambient ............................................................... 10 mA -65C to +150C +300C 52 mW Junction temperature (TJ) ......................................................................................... +150C Thermal resistance, junction-to-case (JC) ............................................................... 80C/W Thermal resistance, junction-to-ambient (JA) .......................................................... 440C/W Ambient operating temperature range (TA) ............................................................... -55C to +125C For device type 02: Maximum power dissipation (PD) ambient : Case outline H ....................................................................................................... Case outline X ....................................................................................................... Junction temperature (TJ) : Case outline H ....................................................................................................... Case outline X ....................................................................................................... Thermal resistance, junction-to-case (JC) : Case outline H ....................................................................................................... Case outline X ....................................................................................................... Thermal resistance, junction-to-ambient (JA) : Case outline H ........................................................................................................ Case outline X ....................................................................................................... 52 mW 52 mW +150C +150C 40C/W 80C/W 170C/W 440C/W 1.4 Recommended operating conditions. Ambient operating temperature range (TA) ............................................................... -55C to +125C 1.5 Radiation features. Maximum total dose available (dose rate = 50 – 300 rads(Si)/s) ............................... 100 krads(Si) 2/ The manufacturer supplying RHA device type 02 on this drawing has performed characterization test to demonstrate that the parts do not exhibit enhanced low dose rate sensitivity (ELDRS) in accordance with MIL-STD-883, method 1019, paragraph 3.13.1.1. Therefore these parts may be considered ELDRS free at a level of 50 krads(Si). ______ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ The manufacturer supplying device type 02 has performed characterization testing in accordance with MIL-STD-883 method 1019 paragraph 3.13.1.1 and the parts exhibited no enhanced low dose rate sensitivity (ELDRS) at a level of 50 krads(Si). The radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A . STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 3 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.1.1 Microcircuit die. For the requirements of microcircuit die, see appendix A to this document. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 4 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MILPRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime 's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 59 (see MIL-PRF-38535, appendix A). STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 5 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C Group A subgroups unless otherwise specified Reverse breakdown voltage VZ Reverse breakdown voltage change with current VZ / IR 1 IR = 1 mA Device type 01, 02 2,3 1 400 A IR 10 mA Limits Min Max 2.495 2.505 2.485 2.515 01, 02 2,3 1 02 8 M,D,P,L,R 1 02 10 VF IF = 2 mA, TA = +25C 1 01 -1 Adjustment range VAR IR = 1 mA, 1 01 15 02 15 Temperature stability 4/ RZ 1 IR = 1 mA 01, 02 2,3 5/ Average temperature coefficient 5/ 6/ mV 10 M,D,P,L VADJ = +0.6 V to VZ -0.6 V V 6 Forward bias voltage Reverse dynamic impedance Unit -0.4 V mV 0.6 1.0 M,D,P,L 1 02 0.8 M,D,P,L,R 1 02 1.0 VZ Tmin TA Tmax 1,2,3 01, 02 15 mV TC Tmin TA Tmax 1,2,3 01, 02 35 ppm / C 1/ RHA devices supplied to this drawing have been characterized through all levels M, D, P, L, and R of irradiation. However, this device is tested at RHA level L and R level. Pre and Post irradiation values are identical unless otherwise specified in Table I. When performing post irradiation electrical measurements for any RHA level, TA = +25C. 2/ The manufacturer supplying device type 02 has performed characterization testing in accordance with MIL-STD-883 method 1019 paragraph 3.13.1.1 and the parts exhibited no enhanced low dose rate sensitivity (ELDRS) at a level of 50 krads(Si). The radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A. 3/ For production testing of these parameters to the limits in table I herein, Ambient temperature (TA) = Junction temperature (TJ). 4/ RZ is guaranteed by VZ / IR test. 5/ If not tested, shall be guaranteed to the limits specified in table I herein. 6/ Average temperature coefficient is defined as the total voltage change divided by the specified temperature range. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 6 Case X FIGURE 1. Case outline. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 7 Case X Dimensions Inches Symbol Millimeters Notes Min Max Min Max A .085 .105 2.16 2.67 b .016 .019 0.41 0.48 3 b1 .016 .021 0.41 0.53 3, 8 D .209 .219 5.31 5.56 D1 .178 .195 4.52 4.95 e .100 T.P 2.54 T.P. 5 e1 .050 T.P 1.27 T.P. 5 F --- .030 --- 7.62 k .036 .046 0.91 1.17 k1 .028 .048 0.71 1.22 L .500 --- 12.7 --- L1 --- .050 --- 1.27 L2 .250 --- 6.35 --- 45 T.P. 4 5 45 T.P. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Three leads: b applies between L1 and L2. b1 applies between L2 and .500 inch (12.70 mm) from the 4. 5. 6. 7. 8. reference plane. Diameter is uncontrolled in L1 and beyond .500 inch (12.70 mm) from the reference plane. Three leads. Measured from the maximum diameter of the product. Leads having a maximum diameter.019 inch (0.48 mm) measured in gauging plane .054 inch (1.37 mm) + .001 inch (0.03 mm) - .000 inch (0.00 mm) below the base plane of the product shall be within .007 inch (0.18 mm) of their true position relative to a maximum width tab. The product may be measured by direct methods or by gauge. All leads: Increase maximum limit by .003 inch (0.08 mm) when lead finish A or B is applied. FIGURE 1. Case outline – Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 8 Device types 01 and 02 02 Case outlines X H Terminal number Terminal symbol 1 ADJ NC 2 +V NC 3 -V NC 4 --- -V 5 --- NC 6 --- NC 7 --- ADJ 8 --- +V 9 --- NC 10 --- NC FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 9 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015. (2) TA = +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table IIA herein. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table IIA herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-38535, appendix B. 4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified. Quality conformance inspection for device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4.1 Group A inspection. a. Tests shall be as specified in table IIA herein. b. Subgroups 4, 5, 6, 7, 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 10 TABLE IIA. Electrical test requirements. Test requirements Interim electrical parameters (see 4.2) Final electrical parameters (see 4.2) Group A test requirements (see 4.4) Group C end-point electrical parameters (see 4.4) Group D end-point electrical parameters (see 4.4) Group E end-point electrical parameters (see 4.4) Subgroups (in accordance with MIL-PRF-38535, table III) Subgroups (in accordance with MIL-STD-883, method 5005, table I) Device class M --- Device class Q --- Device class V --- 1,2,3 1/ 1,2,3 1/ 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 2/ 1,2,3 1,2,3 1,2,3 --- --- 2/ 1 1/ PDA applies to subgroup 1. 2/ Delta limits as specified in table IIB shall be required where specified, and the delta limits shall be computed with reference to the zero hour electrical parameters (see table I). TABLE IIB. Burn-in and operating life test delta parameters. TA = +25C. Parameters Reverse breakdown voltage Symbol VZ Condition Device 1/ End point limits type Min Max 02 2.495 2.505 IR = 1 mA Units V 1/ Deltas are performed at room temperature. TA = 25C. 4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein. 4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883: a. Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. b. TA = +125C, minimum. c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 11 4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. 4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table IIA herein. 4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). a. End-point electrical parameters shall be as specified in table IIA herein. b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25C 5C, after exposure, to the subgroups specified in table IIA herein. 4.4.4.1 Total dose irradiation testing. Total dose irradiation testing shall be performed in accordance with MIL-STD-883 method 1019, condition A, and as specified herein. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.3 Record of users. Military and industrial users should inform DLA Land and Maritime when a system application requires configuration control and which SMD's are applicable to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108. 6.4 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0540. 6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535 and MIL-HDBK-1331. 6.6 Sources of supply. 6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in MIL-HDBK-103 and QML-38535. The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DLA Land and Maritime-VA and have agreed to this drawing. 6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DLA Land and Maritime-VA. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 12 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-89610 A.1 SCOPE A.1.1 Scope. This appendix establishes minimum requirements for microcircuit die to be supplied under the Qualified Manufacturers List (QML) Program. QML microcircuit die meeting the requirements of MIL-PRF-38535 and the manufacturers approved QM plan for use in monolithic microcircuits, multi-chip modules (MCMs), hybrids, electronic modules, or devices using chip and wire designs in accordance with MIL-PRF-38534 are specified herein. Two product assurance classes consisting of military high reliability (device class Q) and space application (device class V) are reflected in the Part or Identification Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. A.1.2 PIN. The PIN is as shown in the following example: 5962 R 89610 Federal stock class designator \ RHA designator (see A.1.2.1) / 02 V 9 A Device type (see A.1.2.2) Device class designator (see A.1.2.3) Die code Die details (see A.1.2.4) \/ Drawing number A.1.2.1 RHA designator. Device classes Q and V RHA identified die meet the MIL-PRF-38535 specified RHA levels. A dash (-) indicates a non-RHA die. A.1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type 02 Generic number RH1009DICE Temperature range Circuit function -55C to +125C Voltage reference diode A.1.2.3 Device class designator. Device class Q or V STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 Device requirements documentation Certification and qualification to the die requirements of MIL-PRF-38535 SIZE 5962-89610 A REVISION LEVEL G SHEET 13 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-89610 A.1.2.4 Die details. The die details designation is a unique letter which designates the die's physical dimensions, bonding pad location(s) and related electrical function(s), interface materials, and other assembly related information, for each product and variant supplied to this appendix. A.1.2.4.1 Die physical dimensions. Die type Figure number 02 A-1 A.1.2.4.2 Die bonding pad locations and electrical functions. Die type Figure number 02 A-1 A.1.2.4.3 Interface materials. Die type Figure number 02 A-1 A.1.2.4.4 Assembly related information. Die type Figure number 02 A-1 A.1.2.4.5 Special handling of dice. Radiation hardened dice require special handling as compared to standard integrated circuit dice. Radiation hardened dice are susceptible to surface damage due to the absence of silicon nitride passivation that is present on most standard dice. Silicon nitride protects the dice surface from scratches by its hard and dense properties. The passivation on radiation hardened dice is silicon dioxide which is much “softer” than silicon nitride. During the visual and preparation for shipment, electrostatic discharge (ESD) safe tweezers are used and only the edge of the die are touched. It is recommended that dice handling be performed with extreme care so as to protect the die surface from scratches. If the need arises to move the die in or out of the chip shipment tray (waffle pack), use an ESD safe plastic tipped bent metal vacuum probe, preferably .020 inch outside diameter x .010 inch inside diameter (for use with tiny parts). The wand should be compatible with continuous air vacuums. The tip material should be static dissipative Delrin (or equivalent) plastic. During die attach, care must be exercised to ensure no tweezers, or other equipment, touch the top of the dice. A.1.3 Absolute maximum ratings. See paragraph 1.3 herein for details. A.1.4 Recommended operating conditions. See paragraph 1.4 herein for details. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 14 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-89610 A.2 APPLICABLE DOCUMENTS. A.2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARD MIL-STD-883 - Test Method Standard Microcircuits. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) A.2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. A.3 REQUIREMENTS A.3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer’s Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. A.3.2 Design, construction and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein and the manufacturer’s QM plan for device classes Q and V. A.3.2.1 Die physical dimensions. The die physical dimensions shall be as specified in A.1.2.4.1 and on figure A-1. A.3.2.2 Die bonding pad locations and electrical functions. The die bonding pad locations and electrical functions shall be as specified in A.1.2.4.2 and on figure A-1. A.3.2.3 Interface materials. The interface materials for the die shall be as specified in A.1.2.4.3 and on figure A-1. A.3.2.4 Assembly related information. The assembly related information shall be as specified in A.1.2.4.4 and on figure A-1. A.3.2.5 Radiation exposure circuit. The radiation exposure circuit shall be as defined in paragraph 3.2.3 herein. A.3.3 Electrical performance characteristics and post-irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post-irradiation parameter limits are as specified in table I of the body of this document. A.3.4 Electrical test requirements. The wafer probe test requirements shall include functional and parametric testing sufficient to make the packaged die capable of meeting the electrical performance requirements in table I. A.3.5 Marking. As a minimum, each unique lot of die, loaded in single or multiple stack of carriers, for shipment to a customer, shall be identified with the wafer lot number, the certification mark, the manufacturer’s identification and the PIN listed in A.1.2 herein. The certification mark shall be a “QML” or “Q” as required by MIL-PRF-38535. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 15 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-89610 A.3.6 Certification of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see A.6.4 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply for this appendix shall affirm that the manufacturer’s product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and the requirements herein. A.3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 shall be provided with each lot of microcircuit die delivered to this drawing. A.4 VERIFICATION A.4.1 Sampling and inspection. For device classes Q and V, die sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer’s Quality Management (QM) plan. The modifications in the QM plan shall not affect the form, fit, or function as described herein. A.4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and as defined in the manufacturer’s QM plan. As a minimum, it shall consist of: a. Wafer lot acceptance for class V product using the criteria defined in MIL-STD-883, method 5007. b. 100% wafer probe (see paragraph A.3.4 herein). c. 100% internal visual inspection to the applicable class Q or V criteria defined in MIL-STD-883, method 2010 or the alternate procedures allowed in MIL-STD-883, method 5004. A.4.3 Conformance inspection. A.4.3.1 Group E inspection. Group E inspection is required only for parts intended to be identified as radiation assured (see A.3.5 herein). RHA levels for device classes Q and V shall be as specified in MIL-PRF-38535. End point electrical testing of packaged die shall be as specified in table IIA herein. Group E tests and conditions are as specified in paragraphs 4.4.4 and 4.4.4.1 herein. A.5 DIE CARRIER A.5.1 Die carrier requirements. The requirements for the die carrier shall be accordance with the manufacturer’s QM plan or as specified in the purchase order by the acquiring activity. The die carrier shall provide adequate physical, mechanical and electrostatic protection. A.6 NOTES A.6.1 Intended use. Microcircuit die conforming to this drawing are intended for use in microcircuits built in accordance with MIL-PRF-38535 or MIL-PRF-38534 for government microcircuit applications (original equipment), design applications, and logistics purposes. A.6.2 Comments. Comments on this appendix should be directed to DLA Land and Maritime -VA, Columbus, Ohio, 43218-3990 or telephone (614)-692-0540. A.6.3 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535 and MIL-HDBK-1331. A.6.4 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535. The vendors listed within MIL-HDBK-103 and QML-38535 have submitted a certificate of compliance (see A.3.6 herein) to DLA Land and Maritime -VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 16 APPENDIX A APPENDIX A FORMS A PART OF SMD 5962-89610 Die bonding pad locations and electrical functions Die physical dimensions. Die size: 50 mils x 54 mils Die thickness: 12 mils Interface materials. Top metallization: Aluminum Backside metallization: (Substrate) alloyed gold layer Glassivation. Type: SiO2 Thickness: 4 kÅ Substrate: Single crystal silicon Assembly related information. Substrate potential: –V Special assembly instructions: Connect backside to (-) pin. FIGURE A-1. Die bonding pad locations and electrical functions. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-89610 A REVISION LEVEL G SHEET 17 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 14-10-16 Approved sources of supply for SMD 5962-89610 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ 5962-8961001XA 5962-8961001XC Vendor CAGE number Vendor similar PIN 2/ Reference military specification PIN 60264 MTLT1009QH M38510/14802BXA 64155 LT1009MH/883 3/ MTL1009MH 3/ LT1009MLDB 60264 MTLT1009QH 3/ MTL1009MH/883 5962R8961002VXC 64155 RH1009MH 5962R8961002VHA 64155 RH1009MW 5962R8961002V9A 64155 RH1009DICE 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number Vendor name and address 60264 Minco Technology Labs, Inc. 1805 Rutherford Lane Austin, TX 78754-5101 64155 Linear Technology Corporation 1630 McCarthy Blvd. Milpitas, CA 95035-7417 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.