TR-55D Transceiver Module Data Sheet © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 1 TR-55D Description TR-55D is a family of IQRF transceiver modules operating in the 868 MHz and 916 MHz license free ISM (Industry, Scientific and Medical) frequency band. Its highly integrated ready-to-use design requires no external components. Extra low power consumption fits for battery powered applications. Vertical mounting and small dimensions allow space saving. Key features Applications • Complete solution with operating system, easy to use • Telemetry • FSK modulation • Building automation • Selectable band 868 / 916 MHz, multiple channel • Control & regulation • MCU with extended resources, user interrupt capability • Remote data acquisition • Extra low power consumption, power management modes • Communication links • SPI interface supported by OS on background • Wireless networks • RF connectivity in many other areas • Serial EEPROM • PWM output • Programmable HW timer • Battery monitoring • 12 pins, 9 I/Os • A/D converter (3 channels) • Analog comparator • Vertical mounting, SIM card compatible • Small dimensions Block diagram © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 2 TR-55D Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICRORISC MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND TO STATED CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE and disclaims all liability arising from this information and its use. Use of MICRORISC devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless MICRORISC from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any MICRORISC intellectual property rights. Electrical specifications Typical values unless otherwise stated Parameters specified in this datasheet are typical values. They are at power supply VCC = 3 V only. VCC voltage different from 3 V can impact on RF range and other parameters. Supply voltage (VCC) 1 Operating temperature Supply current Sleep mode 3.0 V min., 3.4 V max., stabilized 2 -40 °C to +85 °C 380 nA (if all peripherals including MRF49XA disabled 4) Run mode Additional LED supply current 1 mA (MRF49XA disabled) cca 2 mA (if one or two LEDs on). Rough value for brief guidance only. RX mode STD mode: 13 mA LP mode 5 : OS v3.01D: 400 µA, from OS v3.02D: 330 µA XLP mode 5 : OS v3.01D: 35 µA, from OS v3.02D: 25 µA TX mode 14 mA – 24 mA (according to RF output power) RF Band Channels RF data modulation RF data transmission bit rate RFIC RF sensitivity 868 MHz or 916 MHz (software selectable) See IQRF OS User's guide, Appendix 2, Channel maps FSK (frequency-shift keying) 1.2 kb/s 6, 19.2 kb/s, 57.6 kb/s 6, 86.2 kb/s 6 See MRF49XA datasheet RFIC RF output power Programmable in 8 levels (0 – 7), -2.5 dBm/level, see MRF49XA datasheet RF range (TR-52DA) 3 Up to 300 m @ 19.2 kb/s Input voltage on I/O pins 0 V to VCC A/D converter 10 bit, 4 inputs, see PIC16LF1938 datasheet Dimensions 27.4 mm x 14.9 mm x 2.0 mm (TR-55DA) Note 1: RF power and other parameters depend on supply voltage. Refer to datasheets of MCU and RF IC used. Test your application with respect to required supply voltage range. Note 2: RF range may change with lower temperature. Frost, condensation or humidity over 85% may disable module functionality. Module suitability should be tested in final application before volume use. Note 3: RF range strongly depends on module orientation and surroundings. Note 4: Additional current is consumed when a peripheral (e.g. watchdog, Brown-out detection etc.) is enabled. Note 5: Depends on interferences. Note 6: Bit rates different from 19.2 kb/s are preliminary, for experimental purpose only. Users have to ensure observing local provisions and restrictions relating to the use of short range devices by software, e.g. the CEPT ERC/REC 70-03 Recommendation and subsequent amendments in EU. Caution: Electrostatic sensitive device. Observe appropriate precautions for handling © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 3 TR-55D Absolute maximum ratings Stresses above listed maximum values may cause permanent damage to the device and affect device reliability. Functional operation at these or any other conditions beyond those specified is not supported. Supply voltage (VCC) Voltage on I/O pins Storage temperature Ambient temperature under bias 4V -0.3 V to ( VCC + 0.3 V) -40 °C to +85 °C -40 °C to +85 °C Simplified schematics Basic parts Part Type Manufacturer MCU PIC16LF1938–I/ML Microchip RF IC MRF49XA Microchip EEPROM 24AA16/MC Microchip Note 2 kB For more information refer to respective datasheets. © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 4 TR-55D Pin Name Description Q1, C3 VCC Power supply voltage Q2 IO / ADC RB4 AN11 General I/O pin, programmable pull-up and interrupt/wake-up on change (IOC), RFPGM termination Analog A/D input Q3, C5 7 Q4 , C8 IO / ADC / -SS / COUT 8 RA5 General I/O pin, RFPGM termination AN4 Analog A/D input –SS SPI Slave select C2OUT Comparator output IO / SDO RC5 SDO General I/O pin SPI data out Q5, C7 IO / SDI / SDA RC4 General I/O pin SDI SPI data SDA I2C data Q6, C6 IO / SCK / SCL RC3 General I/O pin SCK SPI clock input SCL I2C clock Q7, C4 GND Q8 IN RE3 Ground General input only pin Q9, C1 IO / ADC / C-IN RA0 General I/O pin AN0 Analog A/D input C12IN0 Comparator –input Q10, C2 IO Q11 RC2 General I/O pin IO / RX RC7 RX General I/O pin UART RX Q12 IO / TX / PWM RC6 General I/O pin TX UART TX CCP3 PWM output P1-P2 For manufacturer only Note 7: This pin is used as output during initial ~250 ms boot-up to recognize programming mode. Note 8: External pull-up resistor must be used on this pin when used for RFPGM termination. There are no on-board protection series resistors on I/O pins. It is recommended to use series resistors 200 Ω on each pin. © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 5 TR-55D Figure 1: Relative RF range vs. level for the setTXpower(level) function. Refer to IQRF OS Reference guide. Figure 2: Relative RF range vs. level for the checkRF(level) detection. Refer to IQRF OS Reference guide. Figure 3: Relative RF range vs. antenna orientation (radiation patterns) © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 6 TR-55D Relative decrease of RF input signal vs. antenna edge spacing to conductive areas Conductive areas close to the antenna must be avoided. Figure 4: Perpendicular arrangement Figure 5: Parallel arrangement © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 7 TR-55D Mechanical drawings TR-55DA Top view, units: mm © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 8 TR-55D Application Assembly Vertical mounting: TR-55Dx should be soldered mounted through two holes in the application board. It is not intended for SMT reflow soldering. Top view, units: mm Recommended PCB layout for user application SIM connector: TR-55Dx can also be mounted in SIM connector. Recommended SIM connector: KON-SIM-01. TR-55Dx must not be plugged in devices like DK-EVAL-04 with power supply out of the TR-55Dx range. Such kits are intended for TR modules with built-in LDOs only. For using TR-55Dx with such a kit the KON-TR-01L adapter is intended. See the KON-TR-01L User's guide. As a suitable kit for TR-55Dx the DK-EVAL-04A is recommended. Operating system See IQRF OS User's guide and IQRF OS Reference guide. Software See Application examples www.iqrf.org website. Programming There are the following possibilities to upload an application program in TR-55Dx modules: • Wired upload with TR-55Dx plugged via the SIM connector in the CK-USB-04 or CK-USB-04A programmer. • For TR-55Dx modules populated in an application: • Wired upload using the CK-USB-04A programmer. See the CK-USB-04A User's guide. • Wired upload using the CK-USB-04 programmer and the KON-TR-01P adapter. See the KON-TR-01P User's guide. • RFPGM – RF programmingTM (wireless upload). See the IQRF OS User's guide, Appendix RF programming. © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 9 TR-55D Product information Ordering codes T R - 5 5 D A antenna options: A Type TR-55DA Antenna option Serial EEPROM Internal PCB antenna 2 kB - PCB antenna TR-55DA Document history • 141103 Chapters Pin description and Programming slightly updated. Information regarding directives RoHS and WEEE • • • • • • • 140430 140120 131114 130906 130607 130405 121102 updated and extended. Supply voltage and RF range revised. Datasheet file renamed from DS_TR-55D_131114 to Datasheet_TR-55D_140120. Certification updated for the latest directives. Electrical specification simplified. Operational temperature range extended. Revised. Chapters Specifications and Application precised. First release. © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 10 TR-55D Sales and Service Corporate office MICRORISC s.r.o., Prumyslova 1275, 506 01 Jicin, Czech Republic, EU Tel: +420 493 538 125, Fax: +420 493 538 126, www.microrisc.com Partners and distribution Please visit www.iqrf.org/partners Quality management ISO 9001 : 2009 certified Complies with ETSI directives EN 301489-1 V1.9.2:2011, EN 301489-3 V1.6.1:2013, EN 300220-1 V2.4.1:2012, EN 300220-2 V2.4.1:2012 and VO-R/10/04.2012-7. Complies with directives 2011/65/EU (RoHS) and 2012/19/EU (WEEE). Trademarks The IQRF name and logo and MICRORISC name are registered trademarks of MICRORISC s.r.o. PIC, SPI, Microchip and all other trademarks mentioned herein are property of their respective owners. Legal All information contained in this publication is intended through suggestion only and may be superseded by updates without prior notice. No representation or warranty is given and no liability is assumed by MICRORISC s.r.o. with respect to the accuracy or use of such information. Without written permission it is not allowed to copy or reproduce this information, even partially. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The IQRF ® products utilize several patents (CZ, EU, US) On-line support: [email protected] © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-55D_ 141103 Page 11