TR-58D-RJ Transceiver Module Data Sheet © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 1 TR-58D-RJ Description TR-58D-RJ is a family of IQRF transceiver modules operating in the 868 MHz and 916 MHz license free ISM (Industry, Scientific and Medical) frequency band. Its highly integrated ready-to-use design requires no external components. Microcontroller with built-in operating system, excellent development support, integrated LDO regulator, serial EEPROM and temperature sensor dramatically reduce time of application development. Ultra low power consumption predetermines these modules for use in battery powered applications. Key features Applications • Complete solution with operating system, easy to use • Outdoor lighting • FSK modulation • Telemetry • Selectable RF band 868 / 916 MHz, multiple channel • Building automation • MCU with extended resources, user interrupt capability • Wireless control & regulation • Extra low power consumption, power management modes • Access control • SPI interface supported by OS on background • Remote data acquisition • Serial EEPROM and temperature sensor • Communication links • Programmable HW timer • RF connectivity in many other areas • A/D converter (1 channel) • PWM output • Battery monitoring • 2 LEDs • RJ-45 connector, 8 pins, 4 I/Os • Protective diodes on I/O pins • Fully coated • Resistive against UV radiation Block diagram © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 2 TR-58D-RJ Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICRORISC MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND TO STATED CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE and disclaims all liability arising from this information and its use. Use of MICRORISC devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless MICRORISC from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any MICRORISC intellectual property rights. Electrical specifications Typical values unless otherwise stated Parameters specified in this datasheet are typical values. They are at power supply VOUT = 3 V only. VOUT voltage different from 3 V can impact on RF range and other parameters. Supply voltage (VCC) LDO output (VOUT) 3.1 V to 5.3 V +3 V ± 60 mV ( VCC > 3.1 V), 100 mA max. Operating temperature 1 Supply current Sleep mode Run mode Additional LED supply current -40 °C to +85 °C 1.9 µA (if all peripherals including MRF49XA disabled 3) 1 mA (MRF49XA disabled) cca 2 mA (if one or two LEDs on). Rough value for brief guidance only. RX mode STD mode: 13 mA LP mode 4 : OS v3.01D: 400 µA, from OS v3.02D: 330 µA XLP mode 4 : OS v3.01D: 35 µA, from OS v3.02D: 25 µA TX mode 14 mA – 24 mA (according to RF output power) RF Band Channels RF data modulation RF data transmission bit rate 868 MHz or 916 MHz (software selectable) See IQRF OS User's guide, Appendix 2, Channel maps FSK (frequency-shift keying) 1.2 kb/s 5, 19.2 kb/s, 57.6 kb/s 5, 86.2 kb/s 5 RFIC RF sensitivity See MRF49XA datasheet RFIC RF output power Programmable in 8 levels (0 – 7), -2.5 dBm/level, see MRF49XA datasheet RF range 2 Up to 300 m @ 19.2 kb/s Input voltage on pins 1, 3, 4, 5, 6 Input voltage on pin 2 0 V to VOUT 0 V to 3 V A/D converter 10 bit, 1 input, see PIC16LF1938 datasheet Temperature sensor MCP9804 Size (L x W x H) 29 mm x 40 mm x 52 mm Note 1: RF range may change with lower temperature. Frost, condensation or humidity over 85% may disable module functionality. Module suitability should be tested in final application before volume use. Note 2: RF range strongly depends on module orientation, surroundings and other conditions. Note 3: Additional current is consumed when a peripheral (e.g. watchdog, Brown-out detection etc.) is enabled. Note 4: Depends on interferences. Note 5: RF bit rates different from 19.2 kb/s are preliminary, for experimental purpose only. Users have to ensure observing local provisions and restrictions relating to the use of short range devices by software, e.g. the CEPT ERC/REC 70-03 Recommendation and subsequent amendments in EU. TR modules with metallic shielding of RF circuitry (with the “F“ postfix, e.g. TR-58DF-RJ) must be used in countries where FCC provision is valid. Caution: Electrostatic sensitive device. Observe appropriate precautions for handling © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 3 TR-58D-RJ Absolute maximum ratings Stresses above listed maximum values may cause permanent damage to the device and affect device reliability. Functional operation at these or any other conditions beyond those specified is not supported. Supply voltage (VCC) Voltage on C1, C2, C5 to C8 pins vs. GND Storage temperature Ambient temperature under bias 5.5 V -0.3 V to ( VOUT + 0.3 V) -40 °C to +85 °C -40 °C to +85 °C Simplified schematic Basic components IC Type Manufacturer MCU PIC16LF1938–I/ML Microchip RF IC MRF49XA Microchip LDO voltage regulator MCP1700 Microchip Temperature sensor MCP9804 Microchip EEPROM 24AA16/MC Microchip For more information refer to datasheets of ICs used. © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 4 TR-58D-RJ Pin Name 1 For TR manufacturer only. Leave unconnected. 2 For TR manufacturer only. Leave unconnected. 3 IO / SDI / SDA RC4 General I/O pin SDI SPI data SDA I2C data 4 IO / RX / SDO RC5 SDO RC7 RX 5 Description 6 General I/O pin SPI data out General I/O pin UART RX IO / ADC / TX / -SS / PWM RA5 General I/O pin, -SS SPI Slave select AN4 Analog A/D input RC6 TX CCP3 General I/O pin UART TX PWM output RB4 General I/O pin, programmable pull-up and interrupt/wake-up on change (IOC), RFPGM termination Analog A/D input AN11 6 IO / SCK / SCL RC3 General I/O pin (multiplexed also with LED1 via a resistor) SCK SPI clock input SCL I2C clock 7 VIN Power supply voltage 8 GND Ground Note 6: This pin is used as output during initial ~250 ms boot-up to recognize programming mode. I/O interface Standard 8-pin RJ-45 connector is used. LED interface LED1 It can also be controlled via IQRF OS functions dedicated to LEDR. LED1 control pin is multiplexed with pin 6 via a resistor. LED2 It can also be controlled via IQRF OS functions dedicated to LEDG. Top view © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 5 TR-58D-RJ Figure 1: Relative RF range vs. level for the setTXpower(level) function. Refer to IQRF OS Reference guide. Figure 2: Relative RF range vs. level for the checkRF(level)function. Refer to IQRF OS Reference guide. Figure 3: Relative RF range vs. antenna orientation (radiation patterns) © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 6 TR-58D-RJ Relative decrease of RF input signal vs. antenna edge spacing to conductive areas Conductive areas close to the antenna must be avoided. Figure 4: Parallel arrangement © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 7 TR-58D-RJ Application Mechanical drawings Recommended panel mounting Panel Cut view Assembly TR-58Dx-RJ modules should be mounted with the O-ring Ø 25 mm x 1.5 mm (d1 x d2) by two screws. © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 8 TR-58D-RJ Operating system See IQRF OS User's guide and IQRF OS Reference guide. Software See Application examples on www.iqrf.org website. Programming There are two possibilities to upload an application program in TR-58Dx-RJ modules: • Wireless upload (RFPGM – RF programmingTM). See the IQRF OS User's guide, chapter RF programming, IQRF IDE Help and E12-RFPGM-TST example. • Wired upload using the CK-USB-04(A) programmer and interconnection kit KON-RJ-01. Refer to the CK-USB-04(A) and KON-RJ-01 User's guides for details regarding the upload. In countries where FCC provision is valid, the requirements stated in CB-400-Modular Approval Checklist_JS_WIP.pdf have to be observed. Refer to www.iqrf.org/download, „FCC checklist“. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult IQRF support or an experienced local distributor technician for help. © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 9 TR-58D-RJ Product information Pack list • TR-58DAT(F)-RJ Transceiver module, coated, O-ring included. Ordering codes T R - 5 8 D A PP – RJ RJ-45 connector Peripheral options: nil - No other option T - Temperature sensor F - RF shielding (to meet FCC regulation) PCB antenna Type Antenna Temperature sensor RF shielding On-board PCB Yes – TR-58DATF-RJ On-board PCB Yes Yes TR-58DAT-RJ Recommended options • CK-USB-04(A) • KON-RJ-01 Programmer and debugger for IQRF TR modules Kit to connect TR-58D-RJ with CK-USB-04(A) Document history • 141219 • 141207 • 141103 • • • • 140430 140120 131114 131108 Information regarding FCC directives updated. Recommended panel mounting added. Chapter Pin description slightly updated. Information regarding directives FCC, RoHS and WEEE updated and extended. A bug in packlist fixed. Datasheet file renamed from DS_TR-58D-RJ_131114 to Datasheet_TR-58D-RJ_140120. Certification updated for the latest directives. First release © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 10 TR-58D-RJ Sales and Service Corporate office MICRORISC s.r.o., Prumyslova 1275, 506 01 Jicin, Czech Republic, EU Tel: +420 493 538 125, Fax: +420 493 538 126, www.microrisc.com Partners and distribution Please visit www.iqrf.org/partners Quality management ISO 9001 : 2009 certified Complies with ETSI directives EN 301489-1 V1.9.2:2011, EN 301489-3 V1.6.1:2013, EN 300220-1 V2.4.1:2012, EN 300220-2 V2.4.1:2012 and VO-R/10/04.2012-7. Complies with FCC directives Part 15 Low Power Communication Device Transmitter. FCC ID: R24TR-5XDX. Complies with directives 2011/65/EU (RoHS) and 2012/19/EU (WEEE). Trademarks The IQRF name and logo and MICRORISC name are registered trademarks of MICRORISC s.r.o. PIC, SPI, Microchip and all other trademarks mentioned herein are property of their respective owners. Legal All information contained in this publication is intended through suggestion only and may be superseded by updates without prior notice. No representation or warranty is given and no liability is assumed by MICRORISC s.r.o. with respect to the accuracy or use of such information. Without written permission it is not allowed to copy or reproduce this information, even partially. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The IQRF ® products utilize several patents (CZ, EU, US) On-line support: [email protected] © 2014 MICRORISC s.r.o. www.iqrf.org Datasheet_TR-58D-RJ_141219 Page 11