Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant Moisture Sensitivity Level (MSL) – Level 3 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | Note: MSL3 packaging applies to MOQ of (50) units. Devices sold in less than MOQ quantities will be provided in an ESD bag with Desiccant. FEATURES: APPLICATIONS: • Bluetooth® v2.1+EDR（ Class2） • Automobile Hands free applications • +4dBm TX power, -86.0dBm RX sensitivity • High quality Stereo Headset • Support Profiles: HFP, A2DP, AVRCP, SPP, iAP over • Bluetooth speakers Bluetooth for Apple • VoIP handsets • UART/I2C master • MP3 players • 12 digital PIOs • Support PCM interface (SPDIF ,I2S) • Software Support Apt-X ,AAC, Apt-XLL, • SBC codec. • Wakeup interrupt and watchdog timer • 23.24mm x 11.93mm x 2.05mm • SMT pads for easy and reliable PCB mounting, • FCC ID: OC3BM1856* • QDID: B019582* *Note: ABBTM-NVC-MDCS56 crosses to NovaComm P/N: NVC-MDCS56. BQB/FCC/CE certification documentation is under P/N: NVC-MDCS56 GENERAL DESCRIPTION ABBTM-NVC-MDCS56 is a class 2 Bluetooth® 2.1+EDR (Enhanced Data Rate) module, based on NovaComm’s proprietary technology. It uses CSR’s BlueCore5-Multimedia. With internal DSP and audio codec, it is an ideal solution for integrating Bluetooth® audio functions into various products with minima efforts. With NovaComm’s iNova® stack, designers can easily customize their applications to support different Bluetooth profiles, such as HFP, A2DP, AVRCP, SPP. The module has a 16M bits flash to support different combinationof profiles. And with the built-in firmware, the module can also be connected with Apple’s Authentication Coprocessor to build an iAP over Bluetooth application. Please contact Abracon for more applications. PIN CONFIGURATION: PIN DESCRIPTION: Pin Symbol 1 GND I/O Type 2 RESETB CMOS input with weak internal pull-up 3 SPI_CLK input with weak internal pull-down 4 SPI_MISO CMOS output, tri-state, with weak internal pull-down 5 SPI_MOSI CMOS input, with weak internal pull-down Ground Description Ground Active LOW reset, input debounced so must be low for >5ms to cause a reset Serial Peripheral interface clock for programming only Serial Peripheral Interface output for programming only Serial Peripheral Interface input for programming only Figure 1. Pinout (Topview) ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | PIN DESCRIPTION Pin ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED I/O Type Symbol Description Chip select for Synchronous Serial Interface for programming only, active low 6 SPI_CSB CMOS input with weak internal pull-up 7 PIO3 8 PIO11 9 PCM_OUT 10 11 MIC_RP MIC_RN 12 PIO0 13 PIO1 14 PCM_IN 15 GND 16 PCM_SYNC 17 18 19 RF_GND RF_IN RF_GND 20 PCM_CLK 21 22 23 24 25 26 27 28 29 30 AIO1 GND MIC_LP MIC_LN SPK_LN SPK_LP SPK_RN SPK_RP AIO0 VDD Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down CMOS output, tri-state, with weak internal pull-down Analogue Analogue Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down CMOS Input, with weak internal pulldown Ground Bi-directional with weak internal pulldown RF Ground RF RF Ground Bi-directional with weak internal pulldown Bi-directional Ground Analogue Analogue Analogue Analogue Analogue Analogue Bi-directional 3V3 power input 31 USB_DP Bi-directional 32 33 USB_DN GND 34 PIO14 35 PIO9 Bi-directional Ground Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down 36 PIO4 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 37 GND Ground Ground 38 UART_TX Bi-directional CMOS output, tri-state, with weak internal pull-up UART data output 39 UART_RX CMOS input with weak internal pulldown UART data input 40 PIO8 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 41 PIO7 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 42 PIO6 Bi-directional with programmable strength internal pull-up/down Programmable input/output line Programmable input/output line Programmable input/output line Synchronous Data Output Microphone input positive, right Microphone input negative, right Programmable input/output line Programmable input/output line Synchronous Data Input Ground Synchronous Data Sync RF ground RF Transceiver input/output line RF ground Synchronous Data Clock Analogue programmable input/output line Ground Microphone input positive, left Microphone input negative, right Speaker output negative, left Speaker output positive, left Speaker output negative, right Speaker output positive, right Analogue programmable input/output line 3V3 power input USB data plus with selectable internal 1.5K pull up resistor USB data minus Ground Programmable input/output line Programmable input/output line Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | ELECTRICAL CHARACTERISTICS Absolute Maximum Rating Rating Min Max Unit Storage Temperature -40 +125 °C Operating Temperature Range -40 +85 °C PIO Voltage -0.4 +3.6 V AIO voltage -0.4 +1.57 V VDD Voltage -0.4 +3.6 V USB_DP/USB_DN Voltage -0.4 +3.6 V Other Terminal Voltages except RF -0.4 VDD+0.4 V Recommended Operating Conditions Operating Condition Storage Temperature Min -40 Operating Temperature Range -40 PIO voltage +1.7 AIO Voltage VDD Voltage Typ Max +105 Unit °C +85 °C +3.3 +3.6 V +1.42 +1.5 +1.57 V +2.7 +3.3 +3.6 V INPUT / OUTPUT TERMINAL CHARACTERISTICS Digital Term nals Supply Voltage Levels Min Typ Max Unit Input Voltage Levels VIL input logic level low -0.3 0.25*VDD V VIH input logic level high 0.625*VDD VDD + 0.3 V 0.125 V VDD V Output Voltage Levels VOL output logic level low, IOL = 4.0mA VOH output logic level high, IOH = -4.0mA 0.75*VDD Input and Tri-state Current Ii input leakage current at Vin = VDD or 0V -100 0 100 nA Ioz tri-state output leakage current at Vin = VDD or 0V -100 0 100 nA With strong pull-up -100 -40 -10 μA With strong pull-down 10 40 100 μA With weak pull-up -5.0 -1.0 -0.2 μA With weak pull-down -0.2 1.0 +1.0 5.0 5.0 μA 2000 2000 50 50 kΩ kΩ kΩ kΩ CI Input Capacitance pF Resistive Strength Rpuw weak pull-up strength at VDD-0.2V Rpdw weak pull-down strength at 0.2V Rpus strong pull-up strength at VDD-0.2V Rpds strong pull-down strength at VDD-0.2V ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED 500 500 10 10 Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 RoHS/RoHS II compliant Pb 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | USB ACTERISTICS USB Terminals Min Typ Input Threshold VIL input logic level low VIH input logic level high 0.7*VDD Input Leakage Current GND<VIN<VDD (a) -1 1 CI Input capacitance 2.5 Output Voltage Levels to Correctly Terminated USB Cable VOL output logic level low 0.0 VOH output logic level high Max Unit 0.3*VDD V V 5 10.0 µA pF 0.2 V VDD V 2.8 (a) Internal USB pull-up disabled Internal CODEC – Analog to Digital Converter Parameter Resolution Input Sample Rate, Fsample Condition Min 8 Fsample 8kHz fin = 1kHz B/W = 20Hz ->20kHz 11.025kHz Signal to Noise 16kHz A-Weighted Ration, SNR THD+N<1% 22.050kHz 150mV Vpk-pk 32kHz 44.1kHz Digital Gain Digital Gain Resolution – 1/32 dB Analog Gain Analog Gain Resolution = 3dB Input full scale at maximum gain (differential) Input full scale at minimum gain (differential) 3dB Bandwidth Microphone mode input impedance THD+N (microphone input) @ 30mV rms input ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Typ Max 16 44.1 82 81 80 79 79 78 -24 -3 dB 21.5 42 4 800 20 6 0.04 Unit Bits kHz dB dB mV rms mV rms kHz kΩ % Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 RoHS/RoHS II compliant Pb 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | Internal CODEC – Digital to Analog Converter Parameter Resolution Output Sample Rate, Fsample Condition Min Typ 8 Fsample 8kHz fin = 1kHz B/W = 20Hz ->20kHz 11.025kHz 16kHz A-Weighted Signal to Noise Ration, SNR THD+N<0.01% 22.050kHz 0dBFS signal 32kHz Load = 100 kΩ 44.1kHz 48kHz Digital Gain Digital Gain Resolution – 1/32 dB Analog Gain Analog Gain Resolution = 3dB Output voltage full swing (differential) Resistive Allowed Load Capacitive THD+ N 100 kΩ load THD+ N 16 Ω load SNR (Load 16 Ω, 0dBFS input relative to digital silence) Max 16 48 95 95 95 95 95 95 95 -24 0 dB 21.5 -21 750 16 Unit Bits kHz OC 500 0.01 0.1 95 dB dB mV rms Ω pF % % dB Power Consumption Operating Condition Min (a) Connected Idle (Sniff 1.28secs) Connected with audio streaming (A2DP) Typ Max 0.45 30 35 Unit mA 40 mA Deep Sleep Idle mode 50 µA Radio On (Discovery) 23 mA Radio On ( Inquiry window time) 35 mA Note : Power consumption depends on the firmware used. Typical values are shown in the table. (a) Sniff mode ----- In Sniff mode, the duty cycle of the slave’s activity in the piconet may be reduced. If a slave is in active mode on an ACL logical transport, it shall listen in every ACL slot to the master traffic, unless that link is being treated as a scatternet link or is absent due to hold mode. With sniff mode, the time slots when a slave is listening are reduced, so the master shall only transmit to a slave in specified time slots. The sniff anchor points are spaced regularly with an interval of Tsniff. ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | PHYSICAL INTERFACES Power Supply The module accepts a 3.3V DC power input. Power supply should guarantee good ripple suppression and enough current. Reset The module may be reset from several sources: RESETB pin, power-on reset, a UART break character or via software configured watchdog timer. The RESETB pin is an active low reset and is internally filtered using the internal low frequency clock oscillator. A reset will be performed between 1.5 and 4.0ms following RESETB being active. It is recommended that RESETB be applied for a period greater than 5ms. At reset the digital I/O pins are set to inputs for bi-directional pins and outputs are tri-state. The pull-down state is shown below. Pin Name / Group Pin Status on Reset USB_DP N/a USB_DN N/a UART_RX PD UART_TX PU SPI_MOSI PD SPI_CLK PD SPI_CSB PU SPI_MISO PD RESETB PU PIOs PD PCM_IN PD PCM_CLK PD PCM_SYNC PD PCM_OUT PD Note: Pull-up (PU) and pull-down (PD) default to weak values unless specified otherwise. Digital Audio Interfaces The audio interface circuit consists of: • Stereo audio codec • Dual audio inputs and outputs • A configurable PCM, I²S or SPDIF interface Figure 2 outlines the functional blocks of the interface. The codec supports stereo playback and recording of audio signals at multiple sample rates with a resolution of 16-bit. The ADC and the DAC of the codec each contain 2 independent channels. Any ADC or DAC channel can be run at its own independent sample rate. Figure 2. Audio Interface ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | The interface for the digital audio bus shares the same pins as the PCM codec interface described in Table 1 below,which means each of the audio buses are mutually exclusive in their usage. Table 1 lists these alternative functions. Table 1. Alternative Functions of the digital Audio Bus Interface on the PCM Interface PCM Interface SPDIF Interface I2S Interface PCM_OUT PCM_IN PCM_SYNC PCM_CLK SPDIF_OUT SPDIF_IN SD_OUT SD_IN WS SCK The audio input circuitry consists of a dual audio input that can be configured to be either single-ended or fully differential and programmed for either microphone or line input. It has an analogue and digital programmable gain stage for optimization of different microphones. The audio output circuitry consists of a dual differential class A-B output stage. PCM The audio pulse code modulation (PCM) interface supports continuous transmission and reception of PCM encoded audio data over Bluetooth. Hardware on ABBTM-NVC-MDCS56 allows the data to be sent to and received from a SCO connection. Up to three SCO connections can be supported by the PCM interface at any one time. ABBTM-NVC-MDCS56 can operate as the PCM interface master generating PCM_SYNC and PCM_CLK or as a PCM interface slave accepting externally generated PCM_SYNC and PCM_CLK. ABBTM-NVC-MDCS56 is compatible with a variety of clock formats, including Long Frame Sync, Short Frame Sync and GCI timing environments. It supports 13-bit or 16-bit linear, 8-bit u-law or A-law companded sample formats and can receive and transmit on any selection of three of the first four slots following PCM_SYNC. ABBTM-NVC-MDCS56 interfaces directly to PCM audio devices including the following: • Qualcomm MSM 3000 series and MSM 5000 series CDMA baseband devices • OKI MSM7705 four channel A-law and μ-law CODEC • Motorola MC145481 8-bit A-law and μ-law CODEC • Motorola MC145483 13-bit linear CODEC • STW 5093 and 5094 14-bit linear CODECs(8) • ABBTM-NVC-MDCS56 is also compatible with the Motorola SSI interface ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | 2 Digital Audio Interface (I S) The digital audio interface supports the industry standard formats for I2S, left-justified or right-justified. The interface shares the same pins of the PCM interface as Table 11. The I2S interface can be enabled by using ACCI commands. The module is an I2S slave device with the default firmware. Please contact Abracon for special firmware when using the module as an I2S master. The I2S support following formats: Symbol tch tcl topd tssu tsh tisu tih Parameter SCK Frequency WS Frequency SCK high time SCK low time SCK to SC_OUT delay WS to SCK setup time WS to SCK hold time SD_IN to SCK setup time SD_IN to SCK hodl time Min Typ Max 6.2 96 80 80 20 20 20 20 20 Unit MHz kHz ns ns ns ns ns ns ns Table 2. Digital Audio Interface Slave Timing Figure 3. Digital Audio Interface Modes Figure 4. Digital Audio Interface Slave Timing Symbol topd tspd tisu tih Parameter SCK Frequency WS Frequency SCK to SC_OUT delay SCK to WS delay SD_IN to SCK setup time SD_IN to SCK hodl time Figure 5. Digital Audio Interface Master Timing Min Typ 20 10 Max 6.2 96 20 20 Unit MHz kHz ns ns ns ns Table 3. Digital Audio Interface Master Timing ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | IEC 60958 Interface (SPDIF) The IEC 60958 interface is a digital audio interface that uses bi-phase coding to minimize the DC content of the transmitted signal and allows the receiver to decode the clock information from the transmitted signal. The IEC 60958 specification is based on the 2 industry standards: • AES/EBU • Sony and Philips interface specification SPDIF The interface is compatible with IEC 60958-1, IEC 60958-3 and IEC 60958-4. The SPDIF interface signals are SPDIF_IN and SPDIF_OUT and are shared on the PCM interface pins. The input and output stages of the SPDIF pins can interface to: • A 75Ω coaxial cable with an RCA connector, see Figure 6. • An optical link that uses Toslink optical components, see Figure 7. Figure 6. Example Circuit for SPDIF Interface (Co-Axial) Figure 7. Example Circuit for SPDIF Interface (Optical) ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | Microphone Input Figure 8. Microphone Biasing (Single Channel Shown) The audio input is intended for use in the range from 1μA @ 94dB SPL to about 10μA @ 94dB SPL. With biasing resistors R1 and R2 equal to 1kΩ, this requires microphones with sensitivity between about –40dBV and –60dBV. The microphone for each channel should be biased as shown in Figure 8. Analog Output Stage The output stage digital circuitry converts the signal from 16-bit per sample, linear PCM of variable sampling frequency to a 2Mbits/s 5-bit multi-bit bit stream, which is fed into the analogue output circuitry. The output stage circuit is comprised a DAC with gain setting and class AB amplifier. The output is available as a differential signal between SPKR_A_N and SPKR_L_P for the right channel, as Figure 9 shows, and between SPKL_B_N and SPKL_B_P for the left channel. Figure 9. Speaker output RF Interface Input impedance of the RF port is 50Ω so the user can connect a 50Ω antenna directly to the RF port. General Purpose Analog IO The module has two general-purpose analogue interface pins, AIO0 and AIO1. These are used to access internal circuitry and control signals. Auxiliary functions available via these pins include a 10-bit ADC. Signals selectable at these pins include the band gap reference voltage and a variety of clock signals: 64, 48, 32, 24, 16, 12, 8, 6 and 2MHz (outputted from AIO0 only) and the XTAL and XTAL/2 clock frequency (outputted from AIO0 and AIO1). Please do not connect them if not use. General Purpose Digital IO The module has several general-purpose bi-directional input/outputs (I/O). Any of the PIO lines can be configured as interrupt request lines or wake-up lines from sleep modes. There are nine general purpose digital IOs defined in the module. All these GPIOs can be configured by software to realize various functions, such as button controls, LED displays or interrupt signals to host controller, etc. Please do not connect them if not use. ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | SERIAL INTERFACES Bluetooth UART The module has a standard UART serial interface that provides a simple mechanism for communicating using RS232 protocol. When the module is connected to another digital device, UART_RX and UART_TX transfer data between the 2 devices. Table 4. Possible UART Settings Parameter Baud Rate Possible Values Minimum Maximum Flow Control Parity Number of Stop Bits Bits per Byte 1200 baud (≤2%Error) 9600 baud (≤1%Error) 4M baud (≤1%Error) RTS/CTS or None None, Odd or Even 1 or 2 8 USB This is a full speed (12M bits/s) USB interface for communicating with other compatible digital devices. The module acts as a USB peripheral, responding to request from a master host controller, such as a PC. The USB interface is capable of driving a USB cable directly. No external USB transceiver is required. The device operates as a USB peripheral, responding to requests from a master host controller such as a PC. Both the OHCI and the UHCI standards are supported. The set of USB endpoints implemented can behave as specified in the USB section of the Bluetooth specification v2.0+EDR or alternatively can appear as a set of endpoints appropriate to USB audio devices such as speakers. The module has an internal USB pull-up resistor. This pulls the USB_DP pin weakly high when module is ready to enumerate. It signals to the USB master that it is a full speed (12Mbit/s) USB device. I2 C PIO8, PIO7 and PIO6 can be used to form a master I2C interface as shown in Figure 10. PIO lines need to be pulled up through 2.2Kohm resistors. VDD Figure 10. Example EEPROM Connection with I2C Interface SPI Interface The synchronous serial port interface (SPI) is used for flash/debug the module only. It cannot be used for any user functionality. Please always design test points for this interface on the PCB in case there is need to re-flash the module or flash-in-field in manufacture. ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | iNOVA STACK UART iNova Host Application I/ O Host MCU PCM RFCOMM SDP L2CAP HCI LM LC Baseband Radio Bluetooth Module Figure 11 Software Stack . ABBTM-NVC-MDCS56 is supplied with Bluetooth 2.1+EDR compliant stack firmware. With Novacomm’s iNova profilestacks, the host MCU can easily integrate HFP, A2DP, AVRCP, SPP, HID profiles and iAP over Bluetooth functions. REFERENCE DESIGN ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | RF LAYOUT GUIDELINE ABBTM-NVC-MDCS56 requires an external antenna to radiate and receive the RF signals. Please follow general RF design guidelines to ensure a good RF performance. Placement of the Module and Antenna If PCB antenna is used, please take precaution with the antenna placement. Figure 13 shows some examples of the antenna placement. 1 , 2 , 3 : Recommended antenna placement 4 : Placement not recommended 2 1 3 4 Figure 13. Placement of the Module and Antenna on a PCB Board Feed Line and Antenna The impedance of the feed line between the RF port and the antenna shall be 50Ω. • A good ground directly under the feed line is always needed for impedance control. • Route the feed line as curve lines when needed, avoid 90 or even less degree angles style. • The width of the feed line, the distance of the feed line to the ground plane are keys to the impedance. Please ask your PCB supplier to control the impedance of the feed line. For the antenna, • When PCB antenna is used, matching networks shall be used to optimize the antenna’s signal strength. • Use as many vias as possible to connect the ground planes nearby the antenna. Figure 14. Antenna Reference Design ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | REFLOW PROFILE: ABBTM-NVC-MDCS56 is compatible with industrial standard reflow profile for Pb-free solders. The soldering profile depends on various parameters necessitating a set up for each application. The data here is given only for guidance on solder re-flow. There are four zones: 1. Preheat Zone - This zone raises the temperature at a controlled rate, typically 1-2.5°C/s. 2. Equilibrium Zone - This zone brings the board to a uniform temperature and also activates the flux. The duration in this zone (typically 2-3 minutes) will need to be adjusted to optimise the out gassing of the flux. 3. Reflow Zone- The peak temperature should be high enough to achieve good wetting but not so high as to cause component discoloration or damage. Excessive soldering time can lead to intermetallic growth which can result in a brittle joint. 4. Cooling Zone - The cooling rate should be fast, to keep the solder grains small which will give a longer lasting joint. Typical rates will be 2-5°C/s. Key features of the profile: • Initial Ramp = 1-2.5°C/sec to 175°C ±25°C equilibrium • Equilibrium time = 60 to 180 seconds • Ramp to Maximum temperature (250°C) = 3°C/sec max. • Time above liquidus temperature (217°C): 45-90 seconds • Device absolute maximum reflow temperature: 255°C Note: Apply a local 0.2mm thickness solder cream for the module. Figure 15. Typical Lead-Free Reflow Solder Profile for ABBTM-NVC-MDCS56 OUTLINE DIMENSIONS: Recommended Land Pattern Pin 22 Pin 15 Pin 1 Pin 36 Pin 42 Dimensions: mm ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Bluetooth Module ABBTM-NVC-MDCS56 Pb RoHS/RoHS II compliant 23.24 x 11.93 x 2.05 mm SMT | | | | | | | | | | | | | | | PACKAGING: 100pcs/tray Dimensions: mm Note: MSL3 packaging applies to MOQ of (50) units. Devices sold in less than MOQ quantities will be provided in an ESD bag with Desiccant. ATTENTION: Abracon Corporation’s products are COTS – Commercial-Off-The-Shelf products; suitable for Commercial, Industrial and, where designated, Automotive Applications. Abracon’s products are not specifically designed for Military, Aviation, Aerospace, Life-dependant Medical applications or any application requiring high reliability where component failure could result in loss of life and/or property. For applications requiring high reliability and/or presenting an extreme operating environment, written consent and authorization from Abracon Corporation is required. Please contact Abracon Corporation for more information. ABRACON IS ISOISO 9001 9001:2008 / QS 9000 CERTIFIED Revised: 08.14.13 Visit www.abracon.com for Terms & Conditions of Sale 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com