SLA7051M Data Sheet 28210D* or r t o ive M r D UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER Combining low-power CMOS logic with high-current, high-voltage power FET outputs, the SLA7051M translator/driver provides complete control and drive for a two-phase unipolar stepper motor with internal fixed off time, pulse-width modulation (PWM) control of the output current in a power multi-chip module (PMCM™). The CMOS logic section provides the sequencing logic, direction, full/half-step control, synchronous/asynchronous PWM operation, and a “sleep” function. The minimum CLOCK input is an ideal fit for applications where a complex μP is unavailable or overburdened. TTL or LSTTL may require the use of appropriate pull-up resistors to ensure a proper input-logic high. For PWM current control, the maximum output current is determined by the user’s selection of a reference voltage and sensing resistor. The NMOS outputs are capable of sinking up to 2 A and withstanding 46 V in the off state. Ground-clamp and flyback diodes provide protection against inductive transients. Special power-up sequencing is not required. ABSOLUTE MAXIMUM RATINGS Driver Supply Voltage, VBB ................ 46 V Load Supply Voltage, VM ................... 46 V Output Current, IO ........................... 2.0 A* Logic Supply Voltage, VDD ................ 7.0 V Logic Input Voltage Range, VI .......................... -0.3 V to VDD+ 0.3 V Sense Voltage, VS ........................ ±2.0 V† Reference Input Voltage Range, VREF .................................. -0.3 V to VDD+ 0.3 V Package Power Dissipation, PD ....................................... See Graph Junction Temperature, TJ ............. +150°C Operating Temperature Range, TA ................................. -20°C to +85°C Storage Temperature Range, TS ............................... -30°C to +150°C * Output current rating may be limited by duty cycle, ambient temperature, and heat sinking. Under any set of conditions, do not exceed the specified current rating or junction temperature. † Internal filtering provides protection against transients during the first 1 μs of the current-sense pulse. Full-step (2 phase) and half-step operation are externally selectable. Two-phase drive energizes two adjacent phases in each detent position (AB-BC-CD-DA). This sequence mode offers an improved torquespeed product, greater detent torque, and is less susceptable to motor resonance. Half-step excitation alternates between the one-phase and two-phase modes (A-AB-B-BC-C-CD D-DA), providing an eight-step sequence. The SLA7051M is supplied in an 18-pin single in-line power-tab package with leads formed for vertical mounting (suffix LF871) or horizontal mounting (suffix LF872). The tab is at ground potential and needs no insulation. For high-current or high-frequency applications, external heat sinking may be required. This device is rated for continuous operation between -20°C and +85°C. FEATURES 2 A Output Rating Internal Sequencer for Full or Half-Step Operation PWM Constant-Current Motor Drive Cost-Effective, Multi-Chip Solution 100 V, Avalanche-Rated NMOS Low rDS(on) NMOS Outputs (300 mΩ typical) Advanced, Improved Body Diodes Half-Step and Full-Step Unipolar Drive Inputs Compatible with 3.3 V or 5 V Control Signals Sleep Mode Internal Clamp Diodes Always order by complete part number, e.g., SLA7051MLF871 . SANKEN ELECTRIC CO., LTD. http://www.sanken-ele.co.jp/en/ or r t o e M riv D SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER Functional block diagram Recommended operating conditions Load Supply Voltage, VBB ................................. 10 to 44 V Logic Supply Voltage, VDD ........................... 3.0 V to 5.5 V Reference Input Voltage, VREF .................... 0.1 V to 1.0 V Tab Temperature (no heat sink), TT ...................... <100°C SANKEN ELECTRIC CO., LTD. 2 or r t o e M riv D SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER Electrical characteristics: unless otherwise noted at TA = +25°C, VBB = 24 V, VDD = 5.0 V. Limits Characteristic Symbol Test Conditions Min. Typ. Max. Units Operating 10 — 44 V 100 — — V Output drivers Driver Supply Volt. Range VBB Drain-Source Breakdown V(BR)DS VBB = 44 V, ID = 1 mA Output On Resistance rDS(on) IO = 1.0 A — 300 500 mΩ Body Diode Forward Volt. VF IF = 1.0 A — 0.8 1.1 V Driver Supply Current IBB — — 15 mA VREF > 2.0 V (sleep mode) — — 100 μA Operating 3.0 5.0 5.5 V Control logic Logic Supply Volt. Range VDD Logic Input Voltage VIH 0.75VDD — — V VIL — — 0.25VDD V IIH — ±1.0 — μA IIL — ±1.0 — μA Max. Clock Frequency fclk 100* — — kHz PWM Off Time toff — 12 — μs PWM Min. On Time ton(min) — 5.0 — μs Ref. Input Voltage Range VREF Operating 0.0 — 1.5 V Sleep mode 2.0 — — V — ±10 — μA Logic Input Current Ref. Input Current IREF Sense Voltage VS Trip point — VREF — V Propagation Delay Time tPLH Clock rising edge to output on — 2.5 — μs tPHL Clock rising edge to output off — 2.0 — μs — — 3.0 mA Logic Supply Current IDD Typical values are given for circuit design information only. *Operation at a clock frequency greater than the specified minimum value is possible but not warranted. SANKEN ELECTRIC CO., LTD. 3 or r t o e M riv D SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER Timing chart Logic input timing SANKEN ELECTRIC CO., LTD. 4 or r t o e M riv D SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER Functional description Device operation. The SLA7051M is a complete stepper-motor driver with built-in translator for easy operation with minimal control lines. It is designed to operate unipolar stepper motors in full-step or half-step modes. The current in each pair of outputs, all n-channel MOSFETs, is regulated with internal fixed off-time pulsewidth modulated (PWM) control circuitry. When a step command signal occurs on the clock input the translator automatically sequences to the next step. Clock (step) input. A low-to-high transition on the clock input sequences the translator and advances the motor one increment. The hold state is done by stopping the CLOCK input regardless of the input level Full/half-step select. This logic-level input sets the translator step mode. A logic low is two-phase, full step; a logic high is half step. Changes to this input do not take effect until the rising edge of the clock input. CW/CCW (direction) input. This logic-level input sets the translator step direction. Changes to this input do not take effect until the rising edge of the clock input. Internal PWM current control. Each pair of outputs is controlled by a fixed off-time PWM current-control circuit that limits the load current to a desired value (ITRIP). Initially, an output is enabled and current flows through the motor winding and RS. When the voltage across the current-sense resistor equals the reference voltage, the current-sense comparator resets the PWM latch, which turns off the driver for the fixed off time during which the load inductance causes the current to recirculate for the off time period. The driver is then re-enabled and the cycle repeats. Synchronous operation mode. This function prevents occasional motor noise during a “hold” state, which normally results from asynchronous PWM operation of both motor phases. A logic high at the SYNC input is synchronous operation; a logic low is asynchronous operation. The use of synchronous operation during normal stepping is not recommended because it produces less motor torque and can cause motor vibration due to stair-case current. Sleep mode. Applying a voltage greater than 2 V to the REF pin disables the outputs and puts the motor in a free state (coast). This function is used to minimize power consumption when not in use. It disables much of the internal circuitry including the output MOSFETs and regulator. When coming out of sleep mode, wait 100 μs before issuing a step command to allow the internal circuitry to stabilize. SANKEN ELECTRIC CO., LTD. 5 or r t o e M riv D SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER Applications information Layout. The printed wirting board should use a heavy ground plane. For optimum electrical and thermal performance, the driver should be soldered directly into the board. The driver supply terminal, VBB, should be decoupled with an electrolytic capacitor placed as close to the device as possible. To avoid problems due to capacitive coupling of the high dv/dt switching transients, route the high-level, output traces away from the sensitive, low-level logic traces. Always drive the logic inputs with a low source impedance to increase noise immunity. Grounding. A star ground system located close to the driver is recommended. The logic supply return and the driver supply return should be connected together at only a single point — the star ground. Logic supply voltage, VDD. Transients at this terminal should be held to less than 0.5 V to avoid malfunctioning operation. Both VBB and VDD may be turned on or off separately. Logic inputs. Unused logic inputs (CW/CCW, FULL/ HALF, or SYNC) must be connected to either ground or the logic supply voltage. Current sensing. To minimize inaccuracies caused by ground-trace IR drops in sensing the output current level, the current-sense resistor, RS, should have an independent ground return to the star ground of the device. This path should be as short as possible. For low-value sense resistors, the IR drops in the printed wiring board sense resistor’s traces can be significant and should be taken into account. The use of sockets should be avoided as they can introduce variation in RS due to their contact resistance. PWM current control. The maximum value of current limiting (ITRIP) is set by the selection of RS and the voltage at the REF input with a transconductance function approximated by: ITRIP = VREF/RS The required VREF should not be less than 0.1 V. If it is, RS should be increased for a proportionate increase in VREF. Typical application SANKEN ELECTRIC CO., LTD. 6 or r t o e M riv D SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER Applications Information (cont’d) Reference voltage. In the Typical Application shown, resistors R1 and R2 set the reference voltage as: VREF = (VDD x R2)/(R1 + R2) The trimming of R2 allows for the resistor tolerances and REF input current. The sum of R1+R2 should be less than 50 kΩ to minimize the effect of IREF. Minimum output current. The SLA7051M uses fixed off-time PWM current control. Due to internal logic and switching delays, the actual load current peak will be slightly higher than the calculated ITRIP value (especially for low-inductance loads). These delays, plus the minimum recommended VREF, limit the minimum value the current-control circuitry can regulate. An application with this device should maintain continuous PWM control in order to obtain optimum torque out of the motor. The boundary of the load current (IO(min)) between continuous and discontinuous operation is: IO(min) = [(VM + VSD)/Rm] x [(1/etoff/[Rm x Lm]) - 1] where VM = load supply voltage VF = body diode forward voltage Rm = motor winding resistance toff = PWM off time Lm = motor winding inductance To produce zero current in a motor, the REF input should be pulled above 2 V, turning off all drivers. Synchronous operation mode. If an external signal is not available to control the synchronous operation mode, a simple circuit can keep the SYNC input low while the CLOCK input is active; the SYNC input will go high (synchronous operation) when the CLOCK input stays low (“hold”). The RC time constant determines the sync trransition timing. Temperature effects on FET outputs. Analyzing safe, reliable operation includes a concern for the relationship of NMOS on resistance to junction temperature. Device package power calculations must include the increase in on resistance (producing higher on voltages) caused by increased operating junction temperatures. The figure provides a normalized on-resistance curve, and all thermal calculations should consider increases from the Continuous mode Discontinuous mode Sync. signal generator Normalized FET on resistance SANKEN ELECTRIC CO., LTD. 7 or r t o e M riv D SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER Applications Information (cont’d) given +25°C limits, which may be caused by internal heating during normal operation. These power MOSFET outputs feature an excellent combination of fast switching, ruggedized device design, low on resistance, and cost effectiveness. Avalanche energy capability. There is a surge voltage expected when the output MOSFET turns off, and this voltage may exceed the MOSFET breakdown voltage (V(BR)DS). However, the MOSFETs are avalanche type and as long as the energy (E(AV)), which is imposed on the MOSFET by the surge voltage, is less than the maximum allowable value, it is considered to be within its safe operating area. Note that the maximum allowable avalanche energy is reduced as a function of temperature. In application, the avalanche energy (E(AV)) dissipated by the MOSFET is approximated as E(AV) = VDS(AV) x 1/2 x ID x t Output circuit for avalanche energy calculations Allowable avalanche energy Waveforms during avalanche breakdown SANKEN ELECTRIC CO., LTD. 8 or r t o e M riv D SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER Terminal list Pin Terminal Name 1 OUTA 2 NU 3 OUTA\ Driver output for phase A\ 4 GATEA Phase A MOSFET gate 5 VDD 6 SENSEA Phase A current sense 7 CLOCK Step clock input 8 SYNC 9 REF Current set & “sleep” control 10 GND Supply negative return 11 CW/CCW 12 Terminal Description Driver output for phase A Not usable Logic power supply Synchronous PWM control input Forward/reverse logic control input FULL/HALF Full step/half step logic control input 13 SENSEB Phase B current sense 14 VBB 15 GATEB Phase B MOSFET gate 16 OUTB\ Driver output for phase B\ 17 NU 18 OUTB Driver power supply Not usable Driver output for phase B SANKEN ELECTRIC CO., LTD. 9 or r t o e M riv D SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER SLA7051MLF871 Dimensions in millimeters (controlling dimensions) Dimensions in inches (for reference only) NOTES: 1. 2. 3. 3. 4. Exact body and lead configuration at vendor’s option within limits shown. Lead spacing tolerance is non-cumulative. The shaded area is exposed heat spreader. Recommended mounting hardware torque: 0.490 - 0.822 Nm. Recommended use of metal-oxide-filled, alkyl-degenerated oil-base silicone grease: G746, Shin-Etsu Chemical Co., Ltd. YG6260, Momentive Performance Materials Inc.; SC102, Dow Corning Toray Co., Ltd. SANKEN ELECTRIC CO., LTD. 10 or r t o e M riv D SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER SLA7051MLF872 Dimensions in millimeters (controlling dimensions) Dimensions in inches (for reference only) NOTES: 1. 2. 3. 3. 4. Exact body and lead configuration at vendor’s option within limits shown. Lead spacing tolerance is non-cumulative. The shaded area is exposed heat spreader. Recommended mounting hardware torque: 0.490 - 0.822 Nm. Recommended use of metal-oxide-filled, alkyl-degenerated oil-base silicone grease: G746, Shin-Etsu Chemical Co., Ltd. YG6260, Momentive Performance Materials Inc.; SC102, Dow Corning Toray Co., Ltd. SANKEN ELECTRIC CO., LTD. 11 SLA7051M UNIPOLAR STEPPER-MOTOR TRANSLATOR/PWM DRIVER or r t o e M riv D • The contents in this document are subject to changes, for improvement and other purposes, without notice. Make sure that this is the latest revision of the document before use. • Application and operation examples described in this document are quoted for the sole purpose of reference for the use of the products herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or any other rights of Sanken or any third party which may result from its use. • Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. • Sanken products listed in this document are designed and intended for the use as components in general purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest Sanken sales representative to discuss, prior to the use of the products herein. The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. • In the case that you use Sanken products or design your products by using Sanken products, the reliability largely depends on the degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation range is set by derating the load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. In general, derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. For these stresses, instantaneous values, maximum values and minimum values must be taken into consideration. In addition, it should be noted that since power devices or IC’s including power devices have large self-heating value, the degree of derating of junction temperature affects the reliability significantly. • When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. • Anti radioactive ray design is not considered for the products listed herein. • Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken’s distribution network. • The contents in this document must not be transcribed or copied without Sanken’s written consent. SANKEN ELECTRIC CO., LTD. 12