ISL1904 Datasheet

SIGNS
DED FOR NEW DE
NOT RECOMMEN
T
EN
EM
AC
ED REPL
NO RECOMMEND
at
er
nt
Ce
t
or
nical Supp
c
contact our Tech
/ts
m
co
il.
rs
te
in
www.
1-888-INTERSIL or
Dimmable AC Mains LED Driver with PFC and Primary
Side Regulation
ISL1904
Features
The ISL1904 is a high-performance, critical conduction mode
(CrCM), flyback controller used for single-stage conversion of
the AC mains to a constant current source with power factor
correction (PFC). The controller regulates the output current by
monitoring the primary side switching current so the feedback
signal does not cross the isolation barrier. Operation in CrCM
allows near zero-voltage quasi-resonant switching (ZVS) for
improved efficiency while maximizing magnetic core
utilization. The ISL1904 LED driver provides all of the features
required for high-performance dimmable LED ballast designs
and supports AC or DC input, isolated or non-isolated flyback
and boost topologies. This advanced BiCMOS controller
features all of the functions required to design low cost low
parts count LED driver.
• Excellent LED current regulation over line, load, and
temperature
• 0 - 100% dimming with leading-edge (triac) and
trailing-edge dimmers
• Power factor correction for up to 0.995 power factor and
less than 20% harmonic content
• Critical conduction mode (CrCM) operation for
quasi-resonant high efficiency performance
• Supports universal AC mains input
• Configurable for PWM or DC current dimming control of
LEDs
• Monitors FET switching current for load regulation
• Supports isolated and non-isolated boost and flyback
topologies
• Closed loop soft-start for no overshoot
• OFFREF feature to set dimming off-point to improve fixture
performance matching
• -40°C to +125°C operation
• Pb-free (RoHS compliant)
Applications
• Industrial and commercial LED lighting
• Retrofit LED lamps with triac dimming
• Universal AC mains input LED retrofit lamps
• AC or DC Input LED ballasts
850
5
VDD
CS+
14
DHC
12
AC
LED CURRENT (mA)
800
1
OUT 16
ISL1904
Dimmer
EMI Filter
AC Mains
8
DELADJ
13
GND
3
VREF
OC
6
VERR
9
FB
7
RAMP
IOUT
10
4
750
700
4LEDs
5LEDs
650
6LEDs
600
550
180 190 200 210 220 230 240 250 260 270
LINE VOLTAGE (VRMS)
FIGURE 1A. TYPICAL APPLICATION
FIGURE 1B. LED CURRENT vs LINE VOLTAGE
FIGURE 1. TYPICAL APPLICATION PERFORMANCE
September 20, 2012
FN8286.1
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2012. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
Functional Block Diagram - ISL1904
VREF
BIAS AND
REFERENCE
GENERATOR
VDD
UVLO
+
OTP SHUTDOWN
150C TO 170 C
BG
GND
BIAS/UVLO/OTP
2
DHC
DUTY CYCLE TO
VOLTAGE
CONVERTER
LOW PASS FILTER
REFERENCE OUT
DIMMING PWM
MASTER
OSCILLATOR
CLK
REF
PEAK
DETECTO
AC DETECTION
R
+
PWMOUT
REFINBUFF
AC-PRESENT
+
MINIMUM DIMMING
LEVEL CONTROL
OUT
OFFREF
CS+
+
-
PRIMARY CURRENT
SENSE PROCESSOR
IOUT
+
-
INHIBIT
INHIBIT
IOUT
REFERENCE SS
+
+
_
ISENSE
+
- 1.50 V
REFERENCE SS
BUFFER
DELADJ
SS
QUASI-ZVS
DELAY
+
CRCM
DETECTOR
OC
LEADING EDGE
BLANKING
FMAX
CLAMP
FMIN
CLAMP
PWM
VERR/5
R Q
PRIMARY OC
SS/5
1/5
+
-
SS LOW
PWM
LATCH
PWM
COMPARATOR
0.25V
FAULT LATCH
FN8286.1
September 20, 2012
+
-
S Q
R Q
VERR
CRCM OSCILLATOR/PWM/ERROR AMPLIFIERS
VERR
+
-
SS
1/5
REFINBUFF
EA1
300ms
SOFT-START
+
S Q
+
600mV -
RAMP
200mV
ENABLE
VERR CLAMP
FB1
SOFT-START/POR/
OVP
OVP
ISL1904
AC
TRIANGLE
WAVE
GENERATOR
CLK
Typical Application - Dimmable Isolated Flyback
DIMMER
3
AC
MAINS
EMI
FILTER
OUT 16
2 OFFREF PWMOUT 15
3 VREF
DHC 14
4 IOUT
GND 13
5 CS+
ISL1904
AC 12
6 OC
OVP 11
7 FB
RAMP 10
8 DELADJ
VERR 9
ISL1904
1 VDD
FN8286.1
September 20, 2012
Typical Application - Isolated Flyback with PWM Dimming
DIMMER
4
AC
MAINS
EMI
FILTER
OUT 16
2 OFFREF PWMOUT 15
3 VREF
DHC 14
4 IOUT
GND 13
ISL1904
5 CS+
AC 12
6 OC
OVP 11
7 FB
RAMP 10
8 DELADJ
VERR 9
ISL1904
1 VDD
FN8286.1
September 20, 2012
Typical Application - Dimmable DC Input Boost Converter
9V TO 26V
5
OUT 16
2 OFFREF PWMOUT 15
3 VREF
DHC 14
4 IOUT
GND 13
ISL1904
5 CS+
AC 12
6 OC
OVP 11
7 FB
RAMP 10
8 DELADJ
VERR 9
PWM DIMMING INPUT
90HZ TO 140HZ, 0V TO 4V
0 TO 100% DUTY CYCLE
ISL1904
1 VDD
FN8286.1
September 20, 2012
Typical Application - Dimmable Inverting Boost-Buck (Single Winding Flyback)
6
DIMMER
AC
MAINS
EMI
FILTER
ISL1904
1 VDD
OUT 16
2 OFFREF PWMOUT 15
3 VREF
DHC 14
4 IOUT
GND 13
5 CS+
ISL1904
AC 12
6 OC
OVP 11
7 FB
RAMP 10
8 DELADJ
VERR 9
FN8286.1
September 20, 2012
ISL1904
Pin Configuration
ISL1904
(16 LD QSOP)
TOP VIEW
1 VDD
OUT 16
2 OFFREF PWMOUT 15
3 VREF
DHC 14
4 IOUT
GND 13
5 CS+
AC 12
6 OC
OVP 11
7 FB
RAMP 10
8 DELADJ
VERR 9
Pin Descriptions
PIN #
SYMBOL
DESCRIPTION
1
VDD
VDD is the power connection for the IC. To optimize noise immunity, bypass VDD to GND with a ceramic capacitor as close to the
VDD and GND pins as possible.
2
OFFREF
Sets the reference level to disable the driver at light loading. The turn-off reference can be set at any level between 0 and 0.6V,
corresponding to 0 to 100% of output loading. This feature is normally used in triac-based wall dimmer applications to disable the
output before the dimmer becomes unstable due to insufficient holding current.
3
VREF
The 5.40V reference voltage output having ±100 mV tolerance over line, load and operating temperature. Bypass to GND with a
0.1µF to 3.3µF low ESR capacitor.
4
IOUT
A PWM voltage signal with amplitude and duty cycle proportional to the peak switching current used to determine the output
current.
5
CS+
The input for the CrCM current sense circuit. This input monitors the winding current to determine the critical conduction operating
point.
6
OC
The input to the load current sensing circuitry and the peak overcurrent comparator. The signal is sampled at the peak current level
for each switching cycle, amplified, and output on IOUT as a PWM signal. It must be scaled, filtered and averaged prior to being
applied to the FB pin of the EA. The overcurrent comparator threshold is set at 600mV nominal. Peak OCP performs cycle-by-cycle
over current protection. OCP includes leading-edge-blanking (LEB), which blocks the signal at the beginning of the OUT pulse for the
duration of the blanking period and when the OUT pulse is low.
7
FB
FB is the inverting input to the error amplifier (EA). The feedback signal from IOUT, after being scaled and filtered, is applied to the
error amplifier.
8
DELADJ
Sets delay before a new switching cycles starts. This adjustment allows the user to delay the next switching cycle until the switching
FET drain-source voltage reaches a minimum value to allow quasi-ZVS (Zero Voltage Switching) operation. A resistor to ground
programs the delay. Pulling DELADJ to VREF disables the CrCM oscillator.
9
VERR
Output of the error amplifiers and the control voltage input to the inverting input of the PWM comparator. VERR cannot source
current and requires an external pull-up resistor to VREF.
10
RAMP
This is the input for the sawtooth waveform for the PWM comparator. Using an RC from VREF, a sawtooth waveform is created for
use by the PWM. It is compared to the error amplifier output, Verr, to create the PWM control signal. The RAMP pin is shorted to
GND at the termination of the PWM signal.
11
OVP
12
AC
Input to sense AC voltage presence and amplitude. A resistor divider from line and neutral/line and circuit ground is used to detect
the AC voltage.
13
GND
Signal and power ground connections for this device. Due to high peak currents and high frequency operation, a low impedance
layout is necessary. Ground planes and short traces are highly recommended.
14
DHC
An open drain FET used to load the input voltage to pre-load a triac-based dimmer so that adequate holding current is maintained.
Input to detect an overvoltage (OV) condition on the output. Since the control variable is output current, a fault that results in an
open circuit will cause excessive output voltage. The circuit hysteresis is a switched current source that is active when the OV
threshold is exceeded.
7
FN8286.1
September 20, 2012
ISL1904
Pin Descriptions (Continued)
PIN #
SYMBOL
DESCRIPTION
15
PWMOUT
The PWM gate drive output for LED dimming. The output level is clamped to ~12V for VDD greater than 12V. PWMOUT has pulldown capability when UVLO is active or when the IC is not biased. This output is used to drive the dimming FET in series with the
LED string. The PWM operates at ~ 320Hz.
16
OUT
The gate drive output for the external power FET. OUT is capable of sourcing and sinking 1A @ VDD = 8V. The output level is clamped
to ~12V for VDD greater than 12V. OUT has pull-down capability when UVLO is active or when the IC is not biased.
Ordering Information
PART NUMBER
(Notes 1, 2, 3)
PART
MARKING
ISL1904FAZ
1904 FAZ
ISL1904EVAL2Z
Evaluation Board
TEMP. RANGE
(°C)
-40 to +125
PACKAGE
(Pb-free)
16 Ld QSOP
PKG.
DWG. #
M16.15A
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL1904. For more information on MSL please see tech brief TB363.
Related Products
PART NUMBER
KEY DIFFERENTIATORS
ISL1901
Isolated and non-isolated single-stage flyback regulator.
ISL1902
Isolated and non-isolated single-stage flyback regulator with inrush control and interface features for temperature and
ambient light sensors.
ISL1903
Non-isolated single-stage buck regulator using switch current for regulation.
ISL1904
Isolated single-stage flyback regulator with primary side current sense regulation.
ISL1907
Non-isolated two-stage cascaded boost PFC + buck regulator eliminates dependency on electrolytic capacitors.
ISL1908
Isolated two-stage cascaded boost PFC + flyback regulator eliminates dependency on electrolytic capacitors.
8
FN8286.1
September 20, 2012
ISL1904
Absolute Maximum Ratings (Note 4)
Thermal Information
Supply Voltage, VDD. . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +28.0V
OUT, PWMOUT, DHC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to VDD
Signal Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to VREF + 0.3V
VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GND - 0.3V to 6.0V
Peak OUT Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.0A
Peak PWMOUT Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.0A
ESD Classification
Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . 2500V
Machine Model (Per EIAJ ED-4701 Method C-111) . . . . . . . . . . . . . 200V
Charged Device Model (Per EOS/ESD DS5.3, 4/14/93). . . . . . . . 1000V
Latch up (Per JESD-78B; Class 1, Level A) . . . . . . . . . . . . . . . . . . . . 100mA
Thermal Resistance (Typical)
JA (°C/W) JC (°C/W)
16 Ld QSOP Package (Notes 5, 6) . . . . . . .
85
44
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . -55°C to 150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . . . -65°C to 150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . . . . . . . . . 9 TO 20 VDC
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. All voltages are with respect to GND.
5. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
6. For JC, the “case temp” location is taken at the package top center.
Electrical Specifications
Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram ISL1904” on page 2 and “Typical Application schematics” beginning on page 3. VDD = 17V, RRAMP = 54k, CRAMP = 470pF, TA = -40°C to
+125°C, Typical values are at TA = +25°C; Boldface limits apply over the operating temperature range, -40°C to +125°C.
PARAMETER
TEST CONDITIONS
MIN
(Note 7)
TYP
MAX
(Note 7)
UNITS
-
-
26
V
SUPPLY VOLTAGE
Supply Voltage
Start-Up Current, IDD
VDD = 5.0V
-
100
200
µA
Operating Current, IDD
RLOAD, COUT = 0
-
6.0
7.8
mA
UVLO START Threshold
8.15
8.55
8.95
V
UVLO STOP Threshold
6.80
7.10
7.50
V
-
1.45
-
V
Hysteresis
REFERENCE VOLTAGE VREF
Overall Accuracy
IVREF = 0 - -10mA, 8V < VDD< 26V
5.30
5.40
5.50
V
Long Term Stability
TA = 125°C, 1000 hours (Note 8)
-
10
25
mV
Operational Current (Source)
8V < VDD< 26V
-
-
-10
mA
Current Limit
VREF = 5.00V, 8V < VDD< 26V
-100
-
-15
mA
Load Capacitance
(Note 8)
0.1
-
3.3
µF
Current Limit Threshold
VERR = VREF, RAMP = 0V
570
595
616
mV
IOUT Amplifier Gain
VOC = 0.4V, 8V < VDD< 17V
3.83
4.00
4.18
V/V
IOUT High Level Output Voltage (VOH)
VIOUT @ 0µA - VIOUT @ -100µA,
8V < VDD< 26V
-
-
0.1
V
IOUT Low Level Output Voltage (VOL)
VIOUT @ 100µA, 8V < VDD< 26V
-
-
0.1
V
70
120
146
ns
PEAK CURRENT SENSE (OC)
Leading Edge Blanking (LEB) Duration
OC to OUT Delay + LEB
TA = 25°C
110
170
200
ns
Input Bias Current
VOC = 0.3V
-1.0
-
1.0
µA
9
FN8286.1
September 20, 2012
ISL1904
Electrical Specifications
Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram ISL1904” on page 2 and “Typical Application schematics” beginning on page 3. VDD = 17V, RRAMP = 54k, CRAMP = 470pF, TA = -40°C to
+125°C, Typical values are at TA = +25°C; Boldface limits apply over the operating temperature range, -40°C to +125°C. (Continued)
PARAMETER
TEST CONDITIONS
MIN
(Note 7)
TYP
MAX
(Note 7)
UNITS
-
-
20
Ω
RAMP
RAMP Sink Current Device Impedance
IRAMP = 10 mA
RAMP to PWM Comparator Offset
TA = +25°C
181
235
287
mV
Input Bias Current
VRAMP = 0.3V
-1.0
-
1.0
µA
PWM Restart Delay Range
8V < VDD< 26V
0.2
-
2.0
µs
PWM Restart Cycle Delay
RDELADJ = 20.0k, 8V < VDD< 26V
240
280
320
ns
RDELADJ = 210k, 8V < VDD< 26V
2.00
2.20
2.40
µs
Maximum Frequency Clamp
8V < VDD< 26V, RAMP = 2V,
RRAMP = 100
0.8
1.0
1.2
MHz
Minimum Frequency Clamp
8V < VDD< 26V, RRAMP = 23k
20
25
31
kHz
Minimum On Time
8V < VDD< 26V, FB = 1V, AC = 2V,
RAMP = 0V
173
-
246
ns
VERR to PWM Gain
8V < VDD< 26V
-
0.200
-
V/V
SS to PWM Gain
8V < VDD< 26V
-
0.222
-
V/V
Input Common Mode (CM) Range
(Note 8)
0
-
3.4
V
GBWP
(Note 8)
1.9
-
-
MHz
VERR VOL
IVERR = 6mA, 8V < VDD< 26V
-
-
0.950
V
VERR VOH
IVERR = 1mA (Ext. pull-up)
SS complete
3.90
4.00
4.20
V
Open Loop Gain
(Note 8)
70
-
-
dB
Offset Voltage (VOS)
8V < VDD< 26V
-7.5
-
7.5
mV
Input Bias Current
8V < VDD< 26V
-1.0
-
1.0
µA
Zero Current (CrCM) Detection Threshold, Falling
8V < VDD< 26V
6
-
30
mV
Input Bias Current
8V < VDD< 26V
-1.0
-
1.0
µA
Input Bias Current
8V < VDD< 26V
-50
-
50
nA
Detection Threshold, Falling
8V < VDD< 26V, ACPEAK = 100mV
18
32
51
mV
Detection Threshold Hysteresis
8V < VDD< 26V
-
23
-
mV
Input Operating Range
8V < VDD< 26V
0
-
4.00
V
Clamp Voltage
IACDETECT = 1.0mA
6.8
7.2
7.6
V
EA Reference Input Range
8V < VDD< 26V
0
-
0.538
V
PULSE WIDTH MODULATOR
ERROR AMPLIFIER
CURRENT SENSE (CS+)
AC DETECTOR
10
FN8286.1
September 20, 2012
ISL1904
Electrical Specifications
Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram ISL1904” on page 2 and “Typical Application schematics” beginning on page 3. VDD = 17V, RRAMP = 54k, CRAMP = 470pF, TA = -40°C to
+125°C, Typical values are at TA = +25°C; Boldface limits apply over the operating temperature range, -40°C to +125°C. (Continued)
MIN
(Note 7)
TYP
MAX
(Note 7)
UNITS
Duty Cycle () = 98%
523
548
574
mV
Duty Cycle () = 75%
286
318
340
mV
Duty Cycle () = 50%
117
139
156
mV
Duty Cycle () = 25%
16
32
44
mV
Duty Cycle () = 10%
0
3
11
mV
VDHC = 10mA,
VDD = 8V operating
-
-
600
mV
-
4.0
-
µs
289
389
483
ms
11
27
43
mV
-1.0
-
1.0
µA
Operating Range (Excluding Offset)
0
-
0.5
V
Threshold Hysteresis
33
52
70
mV
Threshold Offset
78
104
129
mV
-
32
-
ms
PARAMETER
EA Reference vs AC Conduction Angle
TEST CONDITIONS
ILPOUT = 0µA, f = 120Hz (rectified),
8V < VDD< 26V
DHC
Low Level Output Voltage (VOL)
Turn-off Delay after AC Returns
SOFT-START
Duration
Reference Soft-Start Initial Step
OFFREF
Input Bias Current
AC Dropout Disable Delay
OUT
High Level Output Voltage (VOH)
VOUT @ 0mA - VOUT @ -100mA,
VDD = 8V operating, RAMP = 0V
-
0.35
1.2
V
Low Level Output Voltage (VOL)
VOUT @ 100mA, VDD = 8V operating
-
0.7
1.2
V
Rise Time
CLOAD = 2.2nF, VDD = 8V,
t90% - t10%
-
35
55
ns
Fall Time
CLOAD = 2.2nF, VDD = 8V,
t10% - t90%
-
25
40
ns
Output Clamp Voltage
VDD = 20V, ILOAD = -10µA
10.5
12.0
13.4
V
Unbiased Output Voltage Clamp
VDD = 6V, ILOAD = 5mA
-
-
1.9
V
High Level Output Voltage (VOH)
VOUT @ 0mA - VOUT @ -10mA,
VDD = 8V operating
-
0.8
1.2
V
Low Level Output Voltage (VOL)
VOUT @ 10mA,
VDD = 8V operating
-
0.8
1.2
V
Rise Time
CLOAD = 1nF, VDD = 8V operating,
t90% - t10%
-
160
240
ns
Fall Time
CLOAD = 1nF, VDD = 8V operating,
t10% - t90%
-
160
240
ns
Output Voltage Clamp
VDD = 20V, ILOAD = -10µA
10.5
12.0
13.4
V
PWMOUT
11
FN8286.1
September 20, 2012
ISL1904
Electrical Specifications
Recommended operating conditions unless otherwise noted. Refer to “Functional Block Diagram ISL1904” on page 2 and “Typical Application schematics” beginning on page 3. VDD = 17V, RRAMP = 54k, CRAMP = 470pF, TA = -40°C to
+125°C, Typical values are at TA = +25°C; Boldface limits apply over the operating temperature range, -40°C to +125°C. (Continued)
PARAMETER
TEST CONDITIONS
Unbiased Output Voltage Clamp
VDD = 6V, ILOAD = 3mA
Frequency
MIN
(Note 7)
TYP
MAX
(Note 7)
UNITS
-
-
1.9
V
291
320
349
Hz
Maximum Duty Cycle
REFIN = 0.5V
-
-
100
%
Minimum On-Time
REFIN = 0V
-
-
0.5
µs
OVP Threshold
1.46
1.50
1.54
V
OVP Hysteresis
10
20
27
µA
Input Bias Current
-1.0
-
1.0
µA
IOVP = 1mA
5.4
-
7.0
V
Thermal Shutdown
(Note 8)
150
160
170
°C
Hysteresis
(Note 8)
-
25
-
°C
OVP
OVP Clamp Voltage
THERMAL PROTECTION
NOTES:
7. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
8. Limits established by characterization and are not production tested.
Test Waveforms and Circuits
8V
OUT 16
1 VDD
2 OFFREF PWMOUT 15
3 VREF
DHC 14
4 IOUT
GND 13
5 CS+
ISL1904
0 TO 1V 120Hz
90%
AC 12
6 OC
OVP 11
7 FB
RAMP 10
8 DELADJ
VERR 9
5k
1nF
OUT
OR
PWMOUT
10%
tR
tF
470pF
54k
FIGURE 2. RISE/FALL TIME TEST CIRCUIT
12
FIGURE 3. RISE/FALL TIMES
FN8286.1
September 20, 2012
ISL1904
Test Waveforms and Circuits (Continued)
OC THRESHOLD
tDELAY
OC
AC
MAINS
LEADING EDGE BLANKING
tDELAY
OC PROPAGATION DELAY
OC + LEB TO OUT DELAY
DHC
OUT
FIGURE 4. OC +LEB TO OUT DELAY
FIGURE 5. AC MAINS TO DHC TIMING
1.001
500
1.000
400
EA REFERENCE (mV)
NORMALIZED VREF
Typical Performance Curves
0.999
0.998
0.997
0.996
-40 -25
-10
5
20
35
50
65
80
95
300
200
100
0
110 125
0
TEMPERATURE (°C)
FIGURE 6. REFERENCE VOLTAGE vs TEMPERATURE
30
40
50
60
70
80
90
100
100
PWMOUT DUTY CYCLE (%)
DELAY TIME (µs)
20
FIGURE 7. EA REFERENCE vs AC SIGNAL DUTY CYCLE
2.5
2.0
1.5
1.0
0.5
0
10
AC CONDUCTION ANGLE (% DUTY CYCLE 120Hz)
0
25
50
75
100
125
150
175
DELAY RESISTANCE (kΩ)
FIGURE 8. DELAY vs DELADJ RESISTANCE
13
200
225
80
60
40
20
0
0
10
20
30
40
50
60
70
80
90
100
AC CONDUCTION ANGLE (% DUTY CYCLE 120Hz)
FIGURE 9. PWMOUT DUTY CYCLE vs AC SIGNAL DUTY CYCLE
FN8286.1
September 20, 2012
ISL1904
Functional Description
Features
The ISL1904 LED driver is an excellent choice for low cost. AC
mains powered single conversion LED lighting applications. It
provides active power factor correction (PFC) to achieve high
power factor using critical conduction mode operation, and
incorporates additional features for compatibility with
triac-based dimmers. Furthermore, it uses primary side current
sensing to regulate the output current, eliminating the need to
cross the isolation boundary to close the feedback control
loop. The ISL1904 includes support for both PWM and DC
current dimming of the output.
Oscillator
The ISL1904 uses a critical conduction mode (CrCM) algorithm
to control the switching behavior of the converter. The ON-time
of the primary power switch is held virtually constant by the
low bandwidth control loop (in PFC applications). The OFF-time
duration is determined by the time it takes the current or
voltage to decay during the flyback period. When the mmf
(magneto motive force) of the transformer decays to zero, the
winding currents are zero and the winding voltages collapse.
Either may be monitored and used to initiate the next
switching cycle. The ISL1904 monitors the CrCM condition
using the CS+ signal. It can be used to monitor either current
or voltage.
Additionally, there is a user adjustable threshold, DELADJ, to
delay the initiation of the next switching cycle to allow the
drain-source voltage of the primary switch to ring to a minimal.
This allows quasi-ZVS operation to reduce capacitive switching
losses and improve efficiency. See “Quasi-Resonant Switching”
on page 18.
By its nature the converter operation is variable frequency.
There are both minimum and maximum frequency clamps
that limit the range of operation. The minimum frequency
clamp prevents the converter from operating in the audible
frequency range. The maximum frequency clamps prevents
operating at very high frequencies that may result in excessive
losses.
An individual switching period is the sum of the ON-time, the
OFF-time, and the restart delay duration. The ON-time is
determined by the control loop error voltage, VERR, and the
RAMP signal. As its name implies, the RAMP signal is a
linearly increasing signal that starts at 0V and ramps to a
maximum of VERR/5 to 235mV. RAMP requires an external
resistor and capacitor connected to VREF to form an RC
charging network. If VERR is at its maximum level of VREF, the
time required to charge RAMP to ~850mV determines the
maximum ON-time of the converter. RAMP is discharged every
switching cycle when the ON-time terminates.
14
The OFF-time duration is determined by the design of the
transformer, which depends on the required energy
storage/transfer and the inductance of the windings. The
transformer design also determines the maximum ON-time that
can be supported without saturation, so, in reality, the
transformer design is critical to every aspect of determining the
switching frequency range. The design methodology is similar to
designing a discontinuous mode (DCM) flyback transformer
except with the constraint that it must operate at the DCM/CCM
boundary at maximum load and minimum input voltage. The
difference is that the converter will always operate at the
DCM/CCM boundary, whereas a DCM converter will be more
discontinuous as the input voltage increases or the load
decreases. In PFC applications, the design is further
complicated by the input voltage waveform, a rectified
sinewave.
Once the output power, Po, the output current, Io, the output
voltage, Vo, and the minimum input AC voltage are known, the
transformer design can be started. From the minimum AC
input voltage, the minimum DC equivalent (RMS) input voltage
must be determined. In PFC applications, the converter
behaves as if the input voltage is an equivalent DC value due to
the low control loop bandwidth. Po determines the amount of
energy that must be stored in the transformer on each
switching cycle, but must be corrected for efficiency. This
includes leakage inductance losses, winding losses, and all
secondary side losses. This can be estimated as a portion of
the total losses, or as is typically done, may be assigned all of
the losses.
A typical minimum operating frequency and maximum duty
cycle must be selected. These are somewhat arbitrary in their
selection, but do ultimately determine core size. The typical
frequency is what occurs when the instantaneous rectified
input AC voltage is exactly at the equivalent DC value. The
frequency will be higher when the instantaneous input voltage
is lower, and lower when the instantaneous input voltage is
higher. However, the duty cycle at the equivalent DC input
voltage determines the ON-time for the entire AC half-cycle
(PFC applications). The ON-time is constant due to the low
bandwidth control loop, but the OFF-time and duty cycle vary
with the instantaneous input voltage since the peak switch
current follows V = Ldi/dt.
The typical frequency may require adjustment once the initial
calculations are complete to see if the operating frequency at
the peak of the minimum AC input voltage is acceptable. A
rule of thumb is to select the typical frequency 25% higher
than the absolute lowest desired frequency that occurs when
operating at the peak of the minimum input AC voltage.
Po
P IN = ------
W
(EQ. 1)
FN8286.1
September 20, 2012
ISL1904
And the OFF-time is shown in Equation 8:
TABLE 1. OSCILLATOR DEFINITIONS
VmINrms =
L s  I s  peak 
t OFF = -------------------------------Vo
Minimum RMS input voltage
VmaxINrms = Maximum RMS input voltage
=
Efficiency
fmin(avg) =
Typical frequency when VIN (instantaneous) = minimum
VIN(rms)
Dmax =
Maximum typical duty cycle desired
Dmin =
Minimum typical duty cycle
tON(MAX) =
ftyp(avg) x Dmax
tON
ON-time of the power FET controlled by OUT
tOFF
OFF-time duration required for CrCM operation
Ls =
Secondary inductance
Lp =
Primary inductance
Nsp =
Transformer turns ratio, Ns/Np
Ip(peak) =
Peak primary current within a switching cycle
tdelay =
User adjustable delay before the next switching cycle
begins
  L p   C oss + C other 
t delay  ----------------------------------------------------------------2
(EQ. 2)
The turns ratio Nsp is calculated next in Equation 3.
V o   1 – D max 
N sp = ---------------------------------------------------  V mINrms  D max
(EQ. 3)
Knowing the secondary inductance and the turns ratio, the
primary inductance can be calculated by using Equation 4.
Ls
L p = ------------2
N sp
With this information, the lowest switching frequency, which
occurs at maximum load and at the peak instantaneous input
voltage at the minimum RMS voltage, can be determined. By
selecting the maximum duty cycle and a typical average
frequency, the ON-time is already determined by Equation 5.
D max
t ON = ------------------------f min  avg 
(EQ. 5)
s
The primary peak current at the end of the ON-time is shown in
Equation 6:
V rms  2  t ON
I p  peak  = ---------------------------------------Lp
A
(EQ. 6)
The peak secondary current is the peak primary current divided
by the transformer turns ratio shown in Equation 7.
I p  peak 
I s  peak  = ---------------------N sp
(EQ. 10)
s
If the lowest frequency does not meet the requirements, then
iterative calculations may be required.
The highest frequency is determined by the shortest ON-time
summed with tdelay. The shortest ON-time occurs at high line and
minimum load, and occurs at or near the AC zero crossing when
the primary (and secondary) current is zero. The minimum
non-zero ON-time the ISL1904 can produce is ~100ns,
suggesting an operating frequency above 1MHz. In any event the
maximum frequency clamp would limit the frequency to about
1MHz. Once the primary and secondary inductances are known,
the general formulae to calculate the ON-time and OFF-time at
an equivalent DC input voltage are shown by Equations 11 and
12:
2  Ls  Io 
L p  N sp  V o
t OFF = -----------------------   1 + ---------------------------------
Vo
L s  V INrms 

(EQ. 4)
H
(EQ. 9)
Hz
The delay time can be approximated if the equivalent
drain-source capacitance (Coss) of the primary switch is known.
This value should also include any parasitic capacitance on the
drain node. These parameters may not be known during the early
stages of the design, but are typically on the order of 300ns to
500ns.
2
H
The lowest switching frequency is the reciprocal of the sum of the
ON-time, the OFF-time, and the delay time is shown in
Equation 9.
1
f min = ---------------------------------------------------t ON + t OFF + t delay
The first calculation required is to determine the required
secondary inductance shown by Equation 2.
V o   1 – D max 
L s = -------------------------------------------f typ  avg   2  I o
(EQ. 8)
s
2  L p  N sp  I o 
L p  N sp  V o
t ON = --------------------------------------   1 + ---------------------------------
V INrms
L s  V INrms 

(EQ. 11)
s
s
(EQ. 12)
It is clear from the equations there is a linear relationship
between load current and frequency. At some light load the
frequency will be limited by the maximum frequency clamp.
There is an inverse relationship between the input voltage and
frequency and its effect is restricted by the typical input voltage
range.
It should be noted, however, that the above equations assume
full conduction angle of the AC mains. When conduction angle
modulating dimmers are used to block a portion of each AC
half-cycle, the switching currents remain essentially unchanged
during the conduction portion of the AC half-cycle as the
conduction angle is reduced. The conduction angle is reduced,
not the amplitude of the waveform envelope. The result being the
steady state frequency behavior will not vary much as the
conduction angle is reduced.
(EQ. 7)
A
15
FN8286.1
September 20, 2012
ISL1904
Soft-Start Operation
Soft-start is not user adjustable and is fixed at ~ 350ms. Both the
duty cycle and control loop reference have soft-start. This
ensures a well behaved closed loop soft-start that results in
virtually no overshoot.
EMI
FILTER
AC
AC Detection and Reference Generation
The ISL1904 creates a 0 to 0.5V reference for the LED current
control loop by directly measuring the conduction angle of the AC
input voltage. The reference changes only with conduction angle
and is virtually unaffected by variation in either voltage
amplitude or frequency.
16
15
14
GND
13
AC
12
11
10
9
ISL1904
AC
EMI
FILTER
FIGURE 11. AC DETECTION
16
15
AC
EMI
FILTER
14
GND 13
AC 12
11
10
ISL1904
9
16
15
FIGURE 10. AC DETECTION
14
GND 13
AC 12
The ISL1904 detects the conduction angle using a divider
network across the AC line and connected to the AC pin, although
it can also be located after the AC bridge rectifier. The advantage
to sensing the AC voltage directly, rather than the rectified
voltage, is that there is no error in detecting the AC zero crossing.
If monitored after the AC rectifier bridge, the AC signal tracks the
filter capacitor voltage, which may not discharge in phase with
the AC voltage. This can lead to incorrect detection of the AC zero
crossing. At light load, the filter capacitor may not fully discharge
before the AC voltage begins to increase again, resulting in no
detection of the AC zero crossing at all.
The AC pin and has an input range of 0 to 4V. The peak of the
input signal should range between 1 and 4 volts for
uncompromised accuracy. The AC detection circuit measures
both the duration of the AC conduction angle and the half-cycle
duration. By comparing the two every half-cycle, the detection
circuit creates a frequency independent reference that is
updated each AC half-cycle.
In the event of an AC outage, the AC mains frequency reference
is lost. The ISL1904 will force the reference to zero volts and
reset the soft-start circuit approximately 35ms after the last AC
zero crossing is detected. If AC is held above it detection
threshold, the internal reference is forced to its maximum of
0.5V.
16
11
10
ISL1904
9
FIGURE 12. ALTERNATE AC DETECTION
AC may be directly coupled to a 90Hz to 130Hz PWM signal to
generate a reference if dimming is desired without using an AC
dimmer.
Primary Current Sensing
The ISL1904 is configured to regulate the output current by
monitoring the primary switch current at the OC pin. The peak
primary switch current is captured, processed, and output on
IOUT as a PWM voltage signal modulated in proportion to the
output current. The IOUT PWM frequency is the same as the
converter switching frequency and its amplitude is equivalent to
4x the peak switch current during the previous ON-time. It must
be scaled and filtered before being input to the control loop at
the FB pin. The required filter time constant depends on the
compensated error amplifier bandwidth. The filter bandwidth
must be greater than the control loop bandwidth, typically an
order of magnitude greater, but it is generally not necessary to
filter the IOUT PWM signal to a low ripple DC level. The
compensated error amplifier, with its limited bandwidth,
performs that function.
FN8286.1
September 20, 2012
ISL1904
The OC pin also provides cycle-by-cycle overcurrent protection.
The ON-time is terminated if OC exceeds 0.6V nominal. There is
~120ns of leading edge blanking (LEB) on OC to minimize or
eliminate external filtering.
XFMR
ISL1904
OUT
Dimming
OC - IOUT
PROCESSOR
OC
The ISL1904 supports both PWM and DC current modulation
dimming. In either case, the control loop determines the average
current delivered to the load.
For PWM dimming, an external FET, controlled by PWMOUT, is
required to gate the drive signal to the switching FET. See “Typical
Application - Dimmable DC Input Boost Converter” on page 5 for
an example. When PWMOUT is high, the main switching FET
operates normally. When PWMOUT is low, the main switching
FET gate signal is blocked and the converter is effectively off.
This method is typically used when the LED string is not ground
referenced.
Another method uses an external FET to interrupt the LED load
current as shown in “Typical Application - Isolated Flyback with
PWM Dimming” on page 4.
Regardless of the dimming method used, the control loop
determines the average current delivered to the load. It does not
matter if the load current is DC or pulsed as long as the control
loop bandwidth is sufficiently lower than the pulsed current
frequency. The converter control loop and output capacitance
operate to filter and average the converter output current
independently of the actual load current waveform.
The dimming PWM and control loop are linked together such that
the PWM duty cycle tracks the main control loop reference
setpoint. If the control loop is set for 50% load, for example, the
dimming PWM duty cycle is set for 50%. The LED current will be
at 100% load for 50% of the time and 0% load for 50% of the
time, which averages to the 50% average load setpoint. See
Figures 7 and 9 for a graphical representation of the relationship
between the control loop reference and PWMOUT duty cycle. It
should be noted that the PWMOUT duty cycle is not allowed to go
to zero.
Control Loop
The control loop configuration is user adjustable with the
selection of the external compensation components. For
applications requiring power factor correction (PFC), a very low
bandwidth integrator is used, typically 20Hz or less. In other
applications, the control loop bandwidth can be increased as
required like any other externally compensated voltage mode
PWM controller.
Referring to Figure 13, the FET switching current flowing through
Rs, is applied to the OC pin of the ISL1904. The peak signal is
sampled, buffered, and output on IOUT as a PWM signal with a
gain of four and a duty equal to the complement of the converter
duty cycle (OUT). The voltage on IOUT, when averaged, is a scaled
representation of the maximum steady state output current, Io.
17
REFERENCE
GENERATOR
R1
VREF
R PU
R FB
+
The usual method of dimming an LED string is to modulate the
DC current through the string. DC current dimming is the lower
cost method, but results in a non-linear dimming characteristic
due to the increasing efficacy of the LEDs as current is reduced.
PWM dimming results in linear dimming behavior.
AC
IOUT
VERR
_
RS
FB
R2
C FILTER
C FB
FIGURE 13. CONTROL LOOP CONFIGURATION
8  Rs
IOUT = ---------------  I o
N sp
(EQ. 13)
V
where IOUT is the average value of IOUT. IOUT must be scaled
such that at maximum output current Io is equal to the
maximum reference level (nominally 0.530V), while also limiting
the maximum peak primary OC signal to less than the
overcurrent threshold of 0.6V.
V OC
R s = -------------------------------------------------------------------------------------------------L p  N sp  V o 

2  2  N sp  I oCL  1 + -----------------------------------
L

s  V mINrms

(EQ. 14)
where IoCL is the output current limit threshold, VOC is the
current limit threshold, and Rs is the current sensing resistor.
Once the value of Rs is determined, Equation 14 can be used to
solve for the level of OC at any steady state current and input
voltage when Io is substituted for IoCL.
L p  N sp  V o

V OC  SS  = R s  2  2  N sp  I o  1 + ---------------------------------
L s  V INrms 

V
(EQ. 15)
where VOC(SS) is the peak steady state value of OC corresponding
for the specific operating conditions.
As indicated previously, IOUT must be scaled properly prior to
connection to the FB input. Using Equation 13, and the value of
Rs obtained from Equation 14, the divider network to scale IOUT
can be determined.
The EA compensation depends on the bandwidth required for the
application. For PFC applications the BW is necessarily limited to
20Hz or less. For other applications, the BW may be increased as
required up to about 1/5 of the lowest switching frequency
allowed as described in “Oscillator” on page 14. For the low BW
applications a Type I compensation configuration is adequate.
For higher BW applications, a Type II configuration may be
required. Figure 13 shows the Type I configuration. Figures 13
and 14 show the Type I and Type II configurations, respectively.
FN8286.1
September 20, 2012
ISL1904
ISL1903
signal could be filtered with a small capacitor placed between
the OV pin and signal ground. This technique does not work well
when the hysteresis is a current source because a current source
takes time to charge the filter capacitor. There is no
instantaneous change in the threshold level rendering the
current hysteresis ineffective. To remedy the situation, the filter
capacitor must be separated from the OV pin by R3. The
capacitor and R3 must be physically close to the OV pin.
IOUT
REFERENCE
GENERATOR
AC
R1
VREF
RPU
RFB1
+
VERR
_
FB
OFFREF Control
R2
CFILTER
CFB2
CFB1
The ISL1904 provides the ability to disable the output based on
the level of the control loop reference, set by the AC conduction
angle on the AC pin. Setting OFFREF to a voltage between 0 and
0.6V determines the threshold voltage that disables the output.
RFB2
FIGURE 14. TYPE II EA CONFIGURATION
REFIN  off  = OFFREF – 0.100
OVP
The ISL1904 has independent overvoltage protection accessed
through the OV pin. There is a nominal 20µA switched current
source used to create hysteresis. The current source is active only
during an OV fault; otherwise, it is inactive and does not affect
the node voltage. The magnitude of the hysteresis voltage is a
VREF
MONITORED
VOLTAGE
1
The ISL1904 uses critical conduction mode PWM control
algorithm. Near zero voltage switching (ZVS) or quasi-resonant
valley switching, as it is sometimes referred to, can be achieved
in the flyback topology by delaying the next switching cycle after
the transformer current decays to zero (critical conduction
mode). The delay allows the primary inductance and capacitance
to oscillate, causing the switching FET drain-source voltage to
ring down to a minimal. If the FET is turned on at this minimal,
the capacitive switching loss (1/2 CV2) is greatly reduced.
0
+
1.5V
C OPT
(EQ. 20)
V
Quasi-Resonant Switching
R1
R3
OFFREF allows the designer to disable the output at a
pre-determined load current to prevent undesirable behavior
such as at light loading conditions when there may be
insufficient current to maintain the holding current in a
triac-based dimmer. Setting OFFREF to less than 100mV disables
this feature. OFFREF has a nominal hysteresis of 50mV.
REFIN  on  = OFFREF – 0.050
20µA
(EQ. 19)
V
_
R2
FIGURE 15. OV HYSTERESIS
Winding Current
function of the external resistor divider impedance.
 R1 + R2 
V ov  ri sin g  = 1.5  --------------------------R2
(EQ. 16)
V
FET D-S Voltage
If the divider formed by R1 and R2 is sufficiently high
impedance, R3 is not required, and the hysteresis is:
V = 20  10
–6
 R1
(EQ. 17)
V
If that does not result in the desired hysteresis then R3 is
needed, and the hysteresis is:
V = 20  10
–6 
 R1 + R2 
 R1 + R3  ---------------------------

R2

FIGURE 16. QUASI-RESONANT NEAR-ZVS SWITCHING
V
(EQ. 18)
If the OV signal requires filtering, the filter capacitor, Copt, should
be placed as shown in Figure 11. The current hysteresis provides
great flexibility in setting the magnitude of the hysteresis voltage,
but it is susceptible to noise due to its high impedance. If the
hysteresis was implemented as a fixed voltage instead, the
18
The delay duration is set with a resistor from DELADJ to ground.
Figure 8 on page 13 shows the graphical relationship between
the delay duration and the value of the DELADJ resistance. The
FN8286.1
September 20, 2012
ISL1904
relationship is linear for resistance values greater than ~ 20 k
and can be estimated using Equation 21.
t delay  73.33 + 10.2  R DELADJ  k 
ns
(EQ. 21)
DHC (Dimmer Holding Current)
The DHC pin provides a method to pre-load a triac-based dimmer
during the period of time when the AC is blocked, with overlap at
each edge of the AC conduction period to ensure adequate
holding current. DHC is an open drain FET used to control an
external resistor to act as the load.
DHC controls a resistor on the external high voltage start-up bias
regulator. See “Typical Application - Dimmable Isolated Flyback”
on page 3 for an example of its usage. Note the series resistor
and diode connecting VDD to the gate of the start-up bias FET. It
is required to keep the device on when the AC voltage is near the
zero-crossing.
Gate Drive
The ISL1904 output is capable of sourcing and sinking up to 1A.
The OUT high level is limited to the OUT clamp voltage or VDD,
whichever is lower.
Thermal Protection
Internal die over-temperature protection is provided. An
integrated temperature sensor protects the device should the
junction temperature exceed +160°C. There is approximately
+10°C of hysteresis.
Ground Plane Requirements
Careful layout is essential for satisfactory operation of the device.
A good ground plane must be employed. VDD and VREF should
be bypassed directly to GND with good high frequency
capacitance.
19
FN8286.1
September 20, 2012
ISL1904
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you
have the latest revision.
DATE
REVISION
CHANGE
August 27, 2012
FN8286.1
Page 15: Changed Equation 6, from H to A.
Equation 7, from H to A. Equation 8
Page 17: Changed Equation 14 from V to ohms
August 10, 2012
FN8286.0
Initial Release.
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products
address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks.
Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a
complete list of Intersil product families.
For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on
intersil.com: ISL1904
To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff
FITs are available from our website at: http://rel.intersil.com/reports/search.php
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
20
FN8286.1
September 20, 2012
ISL1904
Package Outline Drawing
M16.15A
16 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE (QSOP/SSOP)
0.150” WIDE BODY
Rev 3, 8/12
16
INDEX
AREA
3.99
3.81
6.20
5.84
4
0.25(0.010) M
B M
-B-
1
TOP VIEW
DETAIL “X”
SEATING PLANE
-A-
4.98
4.80
GAUGE
PLANE
1.73
1.55
3
-C0.25
0.010
0.249
0.102
0.635 BSC
7
0.89
0.41
0.31
0.20
0.41
x 45° 5
0.25
0.10(0.004)
0.17(0.007) M C A M B S
SIDE VIEW 1
8°
0°
1.55
1.40
7.11
0.249
0.191
SIDE VIEW 2
5.59
4.06
0.38
0.635
NOTES:
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number
95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1994.
3. Package length does not include mold flash, protrusions or gate burrs. Mold flash,
protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side.
4. Package width does not include interlead flash or protrusions. Interlead flash and
protrusions shall not exceed 0.25mm (0.010 inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual index feature must be
located within the crosshatched area.
6. Terminal numbers are shown for reference only.
7. Lead width does not include dambar protrusion. Allowable dambar protrusion shall be
0.10mm (0.004 inch) total in excess of “B” dimension at maximum material condition.
8. Controlling dimension: MILLIMETER.
TYPICAL RECOMMENDED LAND PATTERN
21
FN8286.1
September 20, 2012