1W SMD DC-DC Converter P1GS-Series ● ● ● ● ● ● ● ● SMD Package Single output Regulated output Continuous short circuit protected Up to 1000 VDC isolation MTBF > 3.5 Mio. h at 25°C -40...85°C operating temperature range Efficiency up to 70 % Footprint A Footprint B Model guide Input voltage range Output voltage Output load current [VDC] [VDC] Min. [mA] 4.75..5.25 4.75..5.25 4.75..5.25 11.4..12.6 11.4..12.6 11.4..12.6 5.0 12.0 15.0 5.0 12.0 15.0 15 9 7 15 9 7 Type P1GS0505SB P1GS0512SB P1GS0515SB P1GS1205SB P1GS1212SB P1GS1215SB Part designation structure Output power Series designation P1 1W G Mounting technology S SMD Recommended circuit Input voltage Output voltage 05 12 24 05 12 15 5V 12 V 24 V 5V 12 V 15 V Output power Efficiency typ. Max. [mA] Max. [W] [%] 150 83 67 150 83 67 0.75 1 1 0.75 1 1 68 69 69 68 69 70 Output configuration S Single Footprint configuration Packing A B blanc TR Pins full assembled NC-Pins omitted Tube Reel (Figure1) + Vin + Vout L Cin L External capacitor Vin Version 5 VDC 12 VDC Cout - Vin - Vout (Table 1) Vout Version Cout 5 VDC 4.7 µF 12 VDC 1 µF 15 VDC 1 µF It’s not recommended to connect any external capacitor in the application field with less than 0.5 watt output. Cin 4.7 µF 2.2 µF 1) Requirement on output load To ensure this module can operate efficiently and reliably. During operation, the minimum output load could not be less than 10% of the full load. If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load. 2) Recommended testing circuit If you want to further decrease the input/output ripple, an “LC” filtering network may be connected to the input and output ends of the DC/DC converter, see (Figure 1). It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid mutual interference. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). 3) Overload Protection Under normal operating conditions, the output circuit of these products has no protection against over-current. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. 4) When the environment temperature is higher than 71°C, the product output power should be less then 60% of the rated power! 5) No parallel connection and no plug and play operation! Page 1 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1W SMD DC-DC Converter P1GS-Series Specifications Input Voltage range Filter Input / output: DC-Isolation voltage tested for 60 sec. @ leakage < 1mA Isolation Resistance @ 500 VDC Capacitance Output Output voltage accuracy Line regulation @ 5% Vin change Load regulation @ 10% / 100% load change Output voltage drift Temperature coefficient Ripple & noise Short circuit protection General Switching frequency ± 5% Capacitors 1 kVDC 109 Ω, min. 40 pF, typ. ± 3%, max. @ full load ± 0.25% ± 1% ± 1.2 % @ 1% Vin change 0.03 % / °C, max., @ full load 100 mVp-p Continuous, auto restart Environmental Operating temperature (ambient) Storage temperature Case temperature Case temperature rise at full load Humidity Cooling Physical Package material Weight Reliability, MTBF (MIL-HDBK-217 @ 25 °C) Absolute maximum ratings Manual soldering lead temperature Soldering temperature Moisture sensitivity level (MSL) -40 °C to +85 °C -55 °C to +125 °C 95 °C, max. 25 °C Up to 95 %, non-condensing Free-air convection Epoxy resin (UL94-V0) 1.7 g 3.5 Mio. hours 300 °C max. 10 s max., 1.5 mm distance from body 217 °C for 60 s max., 245 °C peak IPC/JEDEC J-STD-020D.1 ~ 100 kHz Page 2 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1W SMD DC-DC Converter P1GS-Series Dimensions Footprint version "A" Dimensions Footprint version "B" Lead 1 2 3 4 5 6 7 8 9 10 "A" version - Vinput + Vinput Not connected common output - Voutput Not connected + Voutput Not connected Not connected Not connected "B" version - Vinput + Vinput No Pin common output - Voutput No Pin + Voutput No Pin No Pin Not connected Page 3 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1W SMD DC-DC Converter P1GS-Series Page 4 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1W SMD DC-DC Converter P1GS-Series PHI-CON is a trademark of HY-LINE Power Components. Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for use carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 6.14 f Page 5 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]