1.6W Gate Drive DC-DC Converter P2AGDC-Series ● ● ● ● ● ● SIL7 Package Single / dual output 3000 Vrms isolation -40...105°C operating temperature range Efficiency up to 80 % Low couple I/O capacitance Model guide Type designation [VDC] P2AGDC12-1509 P2AGDC12-1508 P2AGDC15-09 P2AGDC15-0909 P2AGDC15-1509 P2AGDC15-1709 P2AGDC24-1509 + Output Input voltage range 11.6…12.4 9…15 14.5…15.5 14.5…15.5 14.5…15.5 14.5…15.5 23.3…24.7 Voltage min. [VDC] 14 14 8 8 14 16.5 14 nom. [VDC] 15 15 9 9 15 17 15 max. [VDC] 16 16 10 10 16 18 16 - Output Current max. [mA] 80 100 111 55 80 80 80 Voltage min. [VDC] -7 -7 -8 -7 -7 -7 nom. [VDC] -8.7 -8 -9 -8.7 -8.7 -8.7 max. [VDC] -10 -9 -10 -10 -10 -10 Current max. [mA] -40 -80 -55 -40 -40 -40 Input current @ no @ full load load min. max. [mA] [mA] 20 162 20 223 20 84 20 84 20 130 20 143 20 81 Efficiency [%] Capacitive load max. [µF] 80 80 80 80 80 80 80 220 220 220 220 220 220 220 Specifications Input / output: Isolation voltage 50 / 60Hz sine wave <1mA, 1min. Isolation Resistance @ 500 VDC Capacitance (@100 kHz, 0.1V) Output Output voltage drift Temperature coefficient Ripple & noise (BW 30 MHz) see figure 1 Short circuit duration Physical Switching frequency Package material Weight Reliability, MTBF (MIL-HDBK-217 @ 25 °C) Environmental EMI CE & RE (with external filter circuit, see figure 1) EMS, ESD 3 kVrms 9 10 Ω min. 6.6 pF, typ. ± 1.5 % max. @ 1% Vin change 0.03 % / °C max., at full load 100 mVp-p typ., 200 mVp-p max. Continuous, automatic restart 100 kHz, typ., 300 kHz, max. Epoxy resin (UL94-V0) 4.3 g 3.5 Mio. hours Operating temperature (ambient) Storage temperature Case temperature rise at Ta 25°C and full load Humidity Cooling Absolute maximum ratings P2AGDC12-1509 P2AGDC12-1508 Vin max. P2AGDC15-xxxx P2AGDC24-1509 Lead soldering temperature 1.5 mm distance from body CISPR22 / EN55022 CLASS B IEC-,EN61000-4-2, contact ± 8 kV perf.criteria B -40 °C to +105 °C -55 °C to +125 °C 25 °C Up to 95 %, non-condensing Free-air convection -0.7 ~ 13 VDC -0.7 ~ 15 VDC -0.7 ~ 16 VDC -0.7 ~ 26 VDC 300 °C max. 10 s Note: 1. 2. 3. 4. 5. 6. The wire between converter and IGBT driver should be so short as possible. External filter capacitors must be placed so near as possible to converter and IGBT driver. The average power of the IGBT driver must be less than the output power of the DC-DC converter. For vibration and shock critical applications is it recommended to fix the converter with glue. The maximum capacitive load is tested at nominal input voltage and full load. Unless otherwise noted, all specifications are measured at Ta 25 °C, humidity <75 %, nominal input voltage and rated output load. 7. All characteristics are for listed models, and non-standard models may perform differently. Please contact our technical support for more detail. 8. Please contact our technical support for any specific requirement. 9. Specifications of this product are subject to changes without prior notice. 10. These products have no overload protection. Protection with a fuse is the simplest method. 11. It is not recommended to increase the output power capability by connecting two or more converters in parallel operation. 12. The converters are not hot-swappable Page 1 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1.6W Gate Drive DC-DC Converter P2AGDC-Series Test circuit +Vin P2AGDC +Vout A GND 100 µF 35V Vin -Vin 100 µF 35V Load V -Vout Recommended circuit for EMI „CLASS B” Figure 1 L1 +Vin P2AGDC +Vout 12 µH Vin Load 4.7 µF 50V -Vin -Vout Page 2 of 5 Deutschland : Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1.6W Gate Drive DC-DC Converter P2AGDC-Series Typical application circuits IGBT driver unit Signal input +Vin Vin P2AGDC15-09 +Vout GND 100 µF 35V 100 µF 35V -Vin IGBT driver unit Signal input +Vin Vin P2AGDC15-1509 P2AGDC24-1509 +Vout GND 100 µF 35V/63V 100 µF 35V -Vout -Vin IGBT driver unit Signal input P78A15 P2AGDC15-1509 +Vin Wide input range 18~32 VDC +Vout GND 47 µF 50V 100 µF 35V 100 µF 35V 100 µF 35V 100 µF 35V -Vout -Vin Page 3 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1.6W Gate Drive DC-DC Converter P2AGDC-Series Page 4 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1.6W Gate Drive DC-DC Converter P2AGDC-Series Dimensions Unit: mm Pin tolerances ± 0.1 mm General tolerances ± 0.5 mm Pin 1 2 3 4 5 6 7 All others + Vinput - Vinput Omitted Omitted - Voutput common output + Voutput P2AGDC15-09 + Vinput - Vinput Omitted Omitted Not connect - Voutput + Voutput PHI-CON is a trademark of HY-LINE Power Components. Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for use carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 10.13 f Page 5 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]