Download

2W DC-DC Converter P2F-Series
●
●
●
●
●
●
8 Pin SIL
Wide 4:1 input range
MTBF >1.7 Mio. Hours
1600 VDC isolation
Continuous short circuit protection
Remote control input on / off
Model guide
Type
Single Output
P2F123R3S
P2F1205S
P2F1212S
P2F1215S
P2F243R3S
P2F2405S
P2F2412S
P2F2415S
P2F483R3S
P2F4805S
P2F4812S
P2F4815S
Dual Output
P2F1205D
P2F1212D
P2F1215D
P2F2405D
P2F2412D
P2F2415D
P2F4805D
P2F4812D
P2F4815D
Input nominal
voltage
[VDC]
Input current
no-load
[mA]
Input current
full-load
[mA]
4.5…18
4.5…18
4.5…18
4.5…18
9…36
9…36
9…36
9…36
18...75
18...75
18...75
18...75
40
40
40
40
25
20
30
30
10
15
15
15
4.5…18
4.5…18
4.5…18
9…36
9…36
9…36
18...75
18...75
18...75
30
30
40
30
30
30
15
15
15
Part number structure
Output power
Series
P2
F
2 Watt
[VDC]
[mA]
[%]
Capacitive
load max.(3)
[µF]
196
225
215
213
96
106
105
105
47
55
55
54
3.3
5.0
12.0
15.0
3.3
5.0
12.0
15.0
3.3
5.0
12.0
15.0
500
400
167
133
500
400
167
133
500
400
167
133
70
74
78
78
71
78
79
79
72
75
75
76
1000
1000
220
100
1000
1000
220
100
1000
1000
220
100
219
213
216
111
108
106
56
56
55
±5.0
±12.0
±15.0
±5.0
±12.0
±15.0
±5.0
±12.0
±15.0
±200
±83
±66
±200
±83
±66
±200
±83
±66
77
78
77
75
77
78
74
74
75
2 x 470
2 x 100
2 x 47
2 x 470
2 x 100
2 x 47
2 x 470
2 x 100
2 x 47
Input voltage
12
12
4.5..18 V
24
9..36 V
48
18..75 V
Output voltage Output current
Output voltage
3R3
3R3
3.3 V
05
5V
12
12 V
15
15 V
S
D
Efficiency typ.
Outputs
S
single
dual
Page 1 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
2W DC-DC Converter P2F-Series
Specifications
Input
Filter
Input reflected ripple current
On / off controll pin
Standby current consumption
Isolation:
I/O isolation voltage
Resistance
Capacitance
Output
Voltage accuracy
Line voltage regulation
Load regulation
Cross regulation, dual output
Short circuit protection
Short circuit restart
Start up time @ Vin nom & R - load
Ripple and noise
(at 20 MHz BW)
Temperature coefficient
Transient recovery time
Transient responce deviation
General
Switching frequency
Reliability calculated MTBF
(Mil-HDBK-217F)
Safety in accordance with
Capacitors
20 mAp-p
on: open
off: -2...-4 mA control current
(via series resistor 1 kΩ,
see figure 3)
2.5 mA typ.
1600 VDC (tested for 3 s)
9
10 Ω, min.
200 pF, typ.
Single outp. ± 1 % @ load 0..100 %
Dual outp. ± 1 % @ load 10..100 %
± 0.2 %, max.
± 1 %, max.
± 5 % (see note 1)
Continuous
Automatic
30 ms, typ
30 mVp-p, max. (see note 2)
± 0.02 % / °C
250 µs, typ., (see note 4)
± 3 %, max. (see note 4)
100 kHz, min.
1.7 Mio.h @ 25°C
IEC60950-1
Environmental
Operating temperatur
(ambient)
Case temperature
Storage temperature
Derating
Humidity
Cooling
Physical
Dimensions SIP8
Weight
Case material
Potting material
EMC Specifiations
Radiated emissions
Conducted emissions
ESD
Radiated immunity
Fast transient (see note 8)
Surge (see note 8)
Conducted surge
PFMF
Absolute maximum ratings
Input surge voltage (100 ms)
Vin 12V types
Vin 24V types
Vin 48V types
Soldering Temperature
1.5 mm from package 10 s
-40 °C to +85 °C
(see derating curve)
100 °C, max.
-40 °C ... +125 °C
None required
Up to 95 %,
non condensing
Free air convection
21.9 x 11.1 x 9.2 mm
4.8 g
Non conductive black plastic,
UL94-V0
Silicon UL94-V0
EN55022 level A
EN55022 level A (see note 7)
EN61000-4-2 pref. criteria A
EN61000-4-3 pref. criteria A
EN61000-4-4 pref. criteria A
EN61000-4-5 pref. criteria A
EN61000-4-6 pref. criteria A
EN61000-4-8 pref. criteria A
-0.7...25 Vdc
-0.7...50 Vdc
-0.7...100 Vdc
260 °C
Notes:
1. One output is 25 % to 100 % burdened, the other output is 100 % burdened. The output voltage deviation can be ± 5 %.
2. Measured with a 1 µF ceramic capacitor. (see Figure 1)
3. Test by minimal Vin and constant resistive load.
4. Test by nominal Vin and 100 % to 25 % load at 25 % load step change.
5. Measured input reflected ripple current with a simulated source inductance of 12 µH and source capacitance of 47 µF,
ESR <1 Ω at 100 kHz. (see Figure 2)
6. Exceeding the absolute ratings of the converter could cause damage. It is not allowed for continuous operatin ratings.
7. Input filter components are be required to help meet conducted emission class A, which application refer to the EMI filter of
design and feature configuration.
8. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5.
Suggested is a value of 220 µF / 100 V of Nippon Chemicon’s KY-Series.
9. All specifications are typical at 25 °C, nominal input voltage and full load unless otherwise noted.
Application circuit IEC61000-4-4 and IEC61000-4-5, see note 8
+ Vin
Nippon Chemicon
KY – Series
220 µF / 100 V
+
Load
- Vin
Page 2 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
2W DC-DC Converter P2F-Series
Output ripple & noise measurement test method
(Figure 1)
Use the following measurement circuit. The oscilloscope mesurement bandwidth must be > 20 MHz.
+Vou
Cout
1 µF
DC/DC-Converter
Resistive
load
Measure points for
oscilloscope
-Vout
Input reflected ripple current measure circuit
(Figure 2)
Input reflected current is measured through a source inductor and a source capacitor at nominal input voltage and full load.
Oscilloscope current probe
+ Vin
12 µH
Measure
point
47 µF
ESR <1Ω
at 100 kHz
Load
- Vin
Remote control function
+ Vin
2
“On” state at open
remote control input
Rem.-Ctrl-Input
1k
3
“Off” state at remote
control current
-2…-4 mA
1
- Vin
6
+ Vout
7
- Vout
EMI Filter
The filter components are used to help meet conducted emissions requirement for the module. These components should be closed
mounted as possible to the module. All leads should be minimized to decrease radiated noise.
+ Vin
L
Load
Cin
CX
- Vin
Type
P2F12xxxx
P2F24xxxx
P2F48xxxx
Cin
220 µF
220 µF
220 µF
CX
10 µF Ceramic
2.2 µF Ceramic
2.2 µF Ceramic
L
2.5 µH
10 µH
18 µH
Page 3 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
2W DC-DC Converter P2F-Series
Page 4 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
2W DC-DC Converter P2F-Series
Dimensions
Pin connections
Pin
1
2
3
5
6
7
8
Single
-V Input
+V Input
Rem. Ctrl. on/off
N.C.
+V Output
-V Output
N.C.
Dual
-V Input
+V Input
Rem. Ctrl. on/off
N.C.
+V Output
Common
-V Output
PHI-CON is a trademark of HY-LINE Holding GmbH.
Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions
carefully before using!
Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without
the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and
whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably
expected to result in significant injury to the user. Rev: 02.15 f
Page 5 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]