12W AC-DC Power-Supply PAC12D ● ● ● ● ● ● ● Enclosed plastic case 85 … 264VAC universal input range Continuously short circuit protected Over voltage protected Isolation class II 4 kVAC isolation 3 years product warranty Model guide Type PAC12D03S PAC12D05S PAC12D12S PAC12D15S PAC12D24S Output voltage [VDC] 3.3 5.0 12 15 24 Output voltage tolerance [%] typ. ±3 ±2 ±2 ±2 ±2 Output current max. [mA] Ripple & noise up to 20 MHz max. [mVp-p] Efficiency typ. @ full load [%] 2400 2400 1000 800 500 100 100 100 100 100 74 78 82 82 83 Stand by consumption [W] max. 0.3 0.3 0.3 0.3 0.3 Capacitive load max. [µF] 10000 10000 5400 2700 1500 Specifications Input Voltage range Line frequency range Full load input current Inrush current Recommended fuse Isolation Isolation voltage (input to output) Leakage current Output Line regulation Load regulation@10 to 100% load change Temperature coefficient Ripple & noise up to 20MHz Protection Short circuit Over current Over voltage clamping General Switching frequency Hold up time @ full load Reliability MTBF MIL-HDBK-217@ 25 °C Safety approvals Safety 85..264 VAC or 120..370 VDC Power derating see diagram 47…63 Hz 280 mA @ 115 VAC, typ. 190 mA @ 230 VAC, typ. 10 A typ. @ 115 VAC 20 A typ. @ 230 VAC 2 A /250V slow blow 4000 VAC for 1 min. 0.1 mA typ.@Vin 230 VAC ±0.5 %, typ. ±1 %, typ. ± 0.02% / °C 100 mV max. Continuous, auto recovery 110 %, min. of full load Z-Diode 100 kHz typ. 120 ms @ 230 VAC. min. 24 ms @ 115 VAC. min. >300000 h EN60950, UL60950 Class II EMI: Conducted & Radiation (without external filter circuit) ESD: Electrostatic discharge EMS: Radiation immunity EFT: Fast transients on mainsline Surge immunity: (without external filter circuit) Surge immunity: (with circuit PIF002B, Fig 2) Conducted disturbance immunity Immunity for power frequency magnetic field Immunities of voltage dip, drop and short interruption Environmental Operating ambient temperature Case temperature Storage temperature Power derating Humidity Cooling Physical Dimensions Weight Case material Wave soldering temperature Manual soldering temperature CE: EN55022 (CISPR22), class B RE: EN55022 (CISPR22), class B IEC-, EN61000-4-2, air ±8 kV, contact ± 6 kV, perf. critera B IEC-, EN61000-4-3, 10 V/m, perf. criteria A IEC-, EN61000-4-4, ± 4 kV, perf. criteria B IEC, EN61000-4-5, ±2 kV, perf. criteria B IEC, EN61000-4-5, ±4 kV, ±6 kV, perf. criteria B IEC-, EN61000-4-6, 10 Vrms, perf. criteria A IEC-, EN61000-4-8, 10 A/m, perf. criteria A IEC-, EN61000-4-11, 0%..70%, perf. criteria B -25 °C to +70 °C (with power derating) 95°C, max. -40 °C to +105 °C See diagram 95 %, non condensing Free air convection 53.5 x 28.8 x 23.5 mm 60 g UL94V-0 rated 260°C, 10s, 1.5mm from case 360°C, 5s, 1.5mm from case Page 1 of 4 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 12W AC-DC Power-Supply PAC12D Page 2 of 4 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 12W AC-DC Power-Supply PAC12D Typical application circuit Figure 1 L F1 PAC12DxxS R1 L ϑ U N Model C1 Cer. [µF] 1 1 1 1 1 PAC12D03S PAC12D05S PAC12D12S PAC12D15S PAC12D24S C1 D1 +Vout C2 +Vo R2 -Vout -Vo N C2 [µF] 220 220 120 120 68 F1 slow blow Fuse R1 NTC R2 MOV D1 TVS 3.15A / 250V~ 3.15A / 250V~ 3.15A / 250V~ 3.15A / 250V~ 3.15A / 250V~ NTC 5D-9 NTC 5D-9 NTC 5D-9 NTC 5D-9 NTC 5D-9 S10K350 S10K350 S10K350 S10K350 S10K350 SMBJ7.0A SMBJ7.0A SMBJ20A SMBJ20A SMBJ30A C4/5 Y type [pF] 2200 2200 2200 2200 2200 C6 X type [µF] 0.15 0.15 0.15 0.15 0.15 L1 [µH] 5 5 5 5 5 L2 CoMo [mH] 20 20 20 20 20 Application circuit and example for ripple and noise reduction Figure 2 PAC12D Input Filter PIF002A F1 L +Vout U + C1 C2 D1 -Vout U U N N PE Recommended layout to Figure 2 Suggestions: wire wide >3 mm, safety distance between input and output > 8 mm Page 3 of 4 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 12W AC-DC Power-Supply PAC12D Note: 1. C1 is a ceramic capacitor, it is used to filter high frequency noise. Output filtering capacitor C2 is a electrolytic capacitor. It is recommended to use high frequency and low impedance electrolytic capacitors. For capacitance and current of capacitor please refer to manufacture’s datasheet. Voltage derating of capacitor should be 80 % or above TVS D1 is a recommended component to protect post-circuits (if converter fails). 2. The Varistor R2 protect the device under surge. 3. Recommended fuse parameter for F1 are 3.15 A / 250 V slow blow. A external input NTC limited the inrush current. Recommended model is NTC 5D-9. (see figure 1 and table) 4. If common requirement to EMC performance, refer to figure 1. If higher requirement to EMC performance, refer to figure 2. C6: X capacitor, recommended values 0.15 μF / 275 V. C4, C5: Y capacitor, recommended values 2200 pF / 400 V. L1: serial inductor, recommended inductance is 5 µH. L2: common mode choke, recommended inductance is about 10 mH…30 mH. Dimensions Pin connections Pin 1 2 3 4 AC In (N) AC In (L) + DC Out - DC Out Note Unit: mm Pin diameter: 1mm ± 0.10 mm General tolerances: ± 0.50 mm PHI-CON is a trademark of HY-LINE Holding GmbH. Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for use carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 05.15 f Page 4 of 4 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]