CHF3020CBF

PL
IA
N
T
Features
This series is currently available but
not recommended for new designs.
M
■ DC to 2 GHz
*R
oH
S
CO
■ Flanged model
■ Low VSWR
Applications
■ High power RF transmission
CHF3020CBF Series Power RF Terminations / Resistors
Absolute Ratings
Power ............... See Rated Power Table
Frequency..................................2.0 GHz
VSWR ............................. 1.30 Maximum
Capacitance .................................0.8 pF
100
Code
500
101
201
251
301
Power (W)
10
25
60
40
0
-55
0
100
150
Heat Sink Temperature (°C)
Product Dimensions
MAX.
6.5
(0.256)
3.7
(0.146)
2.57
(0.101)
5.08
(0.200)
2.54
(0.100)
“L” TERMINATION
1 TAB
(Available only in 50 ohm)
7.62
(0.300)
6.35
(0.250)
2.54
(0.100)
Rated Power
Version
C
D
80
20
1.0
(0.039)
Resistance Value Table
R Value (Ohms)
50
100
200
250
300
Characteristic Curve
% of Rated Power
General Specifications
Substrate ......................................... Beo
Resistive Film ........................ Thick Film
Tab ..................................................... Ag
Cover Substrate ...........................AL203
Mounting Flange......... Cu plated with Ni
Resistance
Termination.................... 50 ohms only
Resistor ...See Resistance Value Table
Tolerance ....................................... ±5 %
Packaging..........................100 pcs./box
3.0
(0.118)
DIA.
DIMENSIONS = MILLIMETERS
(INCHES)
1.0
(0.039)
1.57
(0.062)
2.54
(0.100)
6.5
(0.256)
MAX.
3.7
(0.146)
2.57
(0.101)
5.08
(0.200)
0.1
(0.004)
2.54
(0.100)
How to Order
CHF 3020 C B F 500 L
Model
Size
Version
C = 10 W
D = 25 W
Substrate
Mount
F = Flange
Value (see Resistance Value Table)
Function
L = Termination (50 ohms only)
R = Resistor
REV. 12/15
*RoHS Directive 2002/95/EC Jan. 27, 2003 including
annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
The device characteristics and parameters in this data
sheet can and do vary in different applications and
actual device performance may vary over time.
Users should verify actual device performance in their
specific applications.
“R” RESISTOR
2 TABS
6.35
(0.250)
2.54
(0.100)
3.0
(0.118)
DIA.
2.54
(0.100)
7.62
(0.300)
1.57
(0.062)
0.1
(0.004)
Mounting High Power Devices
The mounting surface must be flat to less
than 0.0254 mm (0.001 ”) and devoid of
scratches or burrs. The underside of the
flange should be brushed with thermal
grease prior to being fastened to the heat
sink with mounting screws. The thermal
grease will fill any air gaps and help to
keep a good thermal contact.
Termination/Resistor
Tabs (1 for Termination, 2 for Resistors)
Circuit Board
Heat Sink/Ground Plane
Flange
Pre-tin the tab prior to installation. Position the tab over the circuit and solder in place.
Ensure that the temperature on the surface of the flange does not exceed 110 ˚C when
running at 100 % of load. If the temperature increases then derate the power.