chf190104kxbf

PL
IA
N
T
Features
This series is currently available but
not recommended for new designs.
M
■ DC to 1 GHz
*R
oH
S
CO
■ Flanged model
■ VSWR of 1.06 @ 800 MHz
Applications
■ 1000 watts @ 110 °C case temperature
■ Broadcast transmitters for television, radio,
radar
CHF190104KxBF Series 1 kW Stripline Termination
Characteristic Curve
100
% of Rated Power
General Specifications
Substrate .........................................BeO
Resistive Film ........................ Thick Film
Tab .......................................... Cu Be/Ag
Cover Substrate ...........................AL203
Mounting Flange......... Cu plated with Ni
Resistance ................................ 50 ohms
Tolerance ....................................... ±5 %
Packaging............................20 pcs./tray
Operating Temperature
............................... -55 °C to +220 °C
Absolute Ratings
Power .........................................1000 W
Frequency..................................1.0 GHz
VSWR ..........1.06 maximum @ 800 MHz
1.25 maximum at 1 GHz
80
60
40
20
0
-55
0
110
220
Case Temperature (°C)
How To Order
CHF 190104 K B F 500 L
Product Dimensions
Model
48.2
(1.898)
Size
39.4
(1.551)
Tab Length
(See Product Dimensions)
K (Standard)
KE (Special Tab Dimensions)
25.4
(1.00)
9.1
(0.358)
6.0
(0.236)
Substrate
Mount
F = Flange
6.85
(0.270)
Value
500 = 50 Ohms
Function
L = Termination
12.7
(0.500)
26.4
(1.039)
4.2
(0.165)
DIA.
4 PLCS.
0.1
(0.004)
DIMENSIONS = MILLIMETERS
(INCHES)
7.0 ± 1.0
(0.28 ± 0.04)
10.0 ± 1.0
TAB LENGTH KE:
(0.39 ± 0.04)
TAB LENGTH K:
7.9
(0.31)
“L” TERMINATION
1 TAB
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.
CHF190104KxBF Series 1 kW Stripline Termination
Typical Performance
Return Loss (dB)
-10.00
-20.00
-30.00
-40.00
-50.00
0.05
1.00
F (GHz)
0.470 GHz -38.48 dB
0.800 GHz -31.83 dB
1.000 GHz -19.53 dB
Mounting High Power Devices
The mounting surface must be flat to less than 0.0254 mm (0.001 inch) and devoid of
scratches or burrs. The underside of the flange should be brushed with thermal
grease prior to being fastened to the heat sink with mounting screws. The thermal
grease will fill any air gaps and help to keep a good thermal contact.
Termination/Resistor
Tabs (1 for Termination, 2 for Resistors)
Circuit Board
Pre-tin the tab prior to installation. Position the tab over the circuit and solder in place.
Heat Sink/Ground Plane
Flange
Ensure that the temperature on the surface of the flange does not exceed 110 ˚C when
running at 100 % of load. If the temperature increases then derate the power.
REV. 12/15
Specifications are subject to change without notice.
The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.
Users should verify actual device performance in their specific applications.