LT1028/LT1128 - Ultralow Noise Precision High Speed Op Amps

LT1028/LT1128
Ultralow Noise Precision
High Speed Op Amps
FEATURES
DESCRIPTION
Voltage Noise
1.1nV/√Hz Max at 1kHz
0.85nV/√Hz Typ at 1kHz
1.0nV/√Hz Typ at 10Hz
35nVP-P Typ, 0.1Hz to 10Hz
n Voltage and Current Noise 100% Tested
n Gain-Bandwidth Product
LT1028: 50MHz Min
LT1128: 13MHz Min
n Slew Rate
LT1028: 11V/µs Min
LT1128: 5V/µs Min
n Offset Voltage: 40µV Max
n Drift with Temperature: 0.8µV/°C Max
n Voltage Gain: 7 Million Min
n Available in 8-Lead SO Package
The LT®1028(gain of –1 stable)/LT1128(gain of +1 stable)
achieve a new standard of excellence in noise performance
with 0.85nV/√Hz 1kHz noise, 1.0nV/√Hz 10Hz noise. This
ultralow noise is combined with excellent high speed
specifications (gain-bandwidth product is 75MHz for
LT1028, 20MHz for LT1128), distortion-free output, and
true precision parameters (0.1µV/°C drift, 10µV offset
voltage, 30 million voltage gain). Although the LT1028/
LT1128 input stage operates at nearly 1mA of collector
current to achieve low voltage noise, input bias current
is only 25nA.
APPLICATIONS
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
n
The LT1028/LT1128’s voltage noise is less than the noise
of a 50Ω resistor. Therefore, even in very low source
impedance transducer or audio amplifier applications,
the LT1028/LT1128’s contribution to total system noise
will be negligible.
Low Noise Frequency Synthesizers
High Quality Audio
n Infrared Detectors
n Accelerometer and Gyro Amplifiers
n350Ω Bridge Signal Conditioning
n Magnetic Search Coil Amplifiers
n Hydrophone Amplifiers
n
n
TYPICAL APPLICATION
Ultralow Noise 1M TIA Photodiode Amplifier
0.1µF
4.32k
1M
D
PHOTO
DIODE
SFH213
VS–
JFET
NXP
S BF862
4.99k
VS–
0.5pF
–
VOUT = ~0.4V + IPD • 1M
LT1028
+
VS = ±15V
1028 TA01
VOLTAGE NOISE DENSITY (nV/√Hz)
VS+
Voltage Noise vs Frequency
10
MAXIMUM
VS = 15V
TA = 25°C
1/f CORNER = 14Hz
TYPICAL
1
1/f CORNER = 3.5Hz
0.1
0.1
1
10
100
FREQUENCY (Hz)
1k
1028 TA02
For more information www.linear.com/LT1028
1028fd
1
LT1028/LT1128
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Supply Voltage
–55°C to 105°C................................................... ±22V
105°C to 125°C................................................... ±16V
Differential Input Current (Note 9)........................±25mA
Input Voltage...............................Equal to Supply Voltage
Output Short-Circuit Duration........................... Indefinite
Operating Temperature Range
LT1028/LT1128AM, M (OBSOLETE).... –55°C to 125°C
LT1028/LT1128AC, C (Note 11).............–40°C to 85°C
Storage Temperature Range
All Devices.......................................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec.)................... 300°C
PIN CONFIGURATION
TOP VIEW
VOS TRIM
8
VOS TRIM 1
–
–IN 2
6 OUT
+
+IN 3
4
V–
(CASE)
TOP VIEW
7 V+
5 OVERCOMP
VOS
TRIM 1
–IN 2
–
7
+IN 3
+
6
V
–
8
4
5
VOS
TRIM
V+
OUT
OVERCOMP
S8 PACKAGE
8-LEAD PLASTIC SOIC
TJMAX = 150°C, θJA = 140°C/W
H PACKAGE
8-LEAD TO-5 METAL CAN
TJMAX = 175°C, θJA = 140°C/W, θJC = 40°C/W
OBSOLETE PACKAGE
TOP VIEW
TOP VIEW
VOS
TRIM 1
–IN 2
–
V
8 OS
TRIM
7 V+
+IN 3
+
6
V
–
4
16 NC
NC 2
15 NC
14 TRIM
TRIM 3
OUT
5 OVERCOMP
N8 PACKAGE
8-LEAD PLASTIC DIP
TJMAX = 150°C, θJA = 150°C/W
–IN 4
–
13 V +
+IN 5
+
NC 7
12 OUT
11 OVERCOMP
10 NC
NC 8
9
V– 6
J8 PACKAGE
8-LEAD CERAMIC DIP
TJMAX = 175°C, θJA = 140°C/W, θJC = 40°C/W
OBSOLETE PACKAGE
NC 1
NC
SW PACKAGE
16-LEAD PLASTIC SOL
TJMAX = 150°C, θJA = 130°C/W
NOTE: THIS DEVICE IS NOT RECOMMENDED FOR NEW DESIGNS
1028fd
2
For more information www.linear.com/LT1028
LT1028/LT1128
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
SPECIFIED TEMPERATURE RANGE
LT1028ACN8#PBF
N/A
LT1028ACN8
8-Lead PDIP
0°C to 70°C
LT1028CN8#PBF
N/A
LT1028CN8
8-Lead PDIP
0°C to 70°C
LT1128ACN8#PBF
N/A
LT1128ACN8
8-Lead PDIP
0°C to 70°C
LT1128CN8#PBF
N/A
LT1128CN8
8-Lead PDIP
0°C to 70°C
LT1028CS8#PBF
LT1028CS8#TRPBF
1028
8-Lead Plastic Small Outline
0°C to 70°C
LT1128CS8#PBF
LT1128CS8#TRPBF
1128
8-Lead Plastic Small Outline
0°C to 70°C
LT1028CSW#PBF
LT1028CSW#TRPBF
LT1028CSW
16-Lead Plastic SOIC (Wide)
0°C to 70°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
ELECTRICAL CHARACTERISTICS
VS = ±15V, TA = 25°C unless otherwise noted.
LT1028AM/AC
LT1128AM/AC
SYMBOL
PARAMETER
CONDITIONS
VOS
∆VOS
∆Time
IOS
IB
en
Input Offset Voltage
Long Term Input Offset
Voltage Stability
Input Offset Current
Input Bias Current
Input Noise Voltage
Input Noise Voltage Density
In
Input Noise Current Density
CMRR
PSRR
AVOL
Input Resistance
Common Mode
Differential Mode
Input Capacitance
Input Voltage Range
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
TYP
MAX
(Note 2)
(Note 3)
10
0.3
VCM = 0V
VCM = 0V
0.1Hz to 10Hz (Note 4)
fO = 10Hz (Note 5)
fO = 1000Hz, 100% Tested
fO = 10Hz (Notes 4 and 6)
fO = 1000Hz, 100% Tested
12
±25
35
1.00
0.85
4.7
1.0
VOUT
Maximum Output Voltage Swing
SR
Slew Rate
GBW
Gain-Bandwidth Product
ZO
IS
Open-Loop Output Impedance
Supply Current
VCM = ±11V
VS = ±4V to ±18V
RL ≥ 2k, VO = ±12V
RL ≥ 1k, VO = ±10V
RL ≥ 600Ω, VO = ±10V
RL ≥ 2k
RL ≥ 600Ω
AVCL = –1
AVCL = –1
fO = 20kHz (Note 7)
fO = 200kHz (Note 7)
VO = 0, IO = 0
MIN
LT1028M/C
LT1128M/C
LT1028
LT1128
LT1028
LT1128
±11.0
114
117
7.0
5.0
3.0
±12.3
±11.0
11.0
5.0
50
13
300
20
5
±12.2
126
133
30.0
20.0
15.0
±13.0
±12.2
15.0
6.0
75
20
80
7.4
MIN
TYP
MAX
UNITS
40
20
0.3
80
µV
µV/Mo
50
±90
75
1.7
1.1
10.0
1.6
18
±30
35
1.0
0.9
4.7
1.0
100
±180
90
1.9
1.2
12.0
1.8
nVP-P
nV/√Hz
nV/√Hz
pA/√Hz
pA/√Hz
9.5
300
20
5
±12.2
126
132
30.0
20.0
15.0
±13.0
±12.2
15.0
6.0
75
20
80
7.6
10.5
MΩ
kΩ
pF
V
dB
dB
V/µV
V/µV
V/µV
V
V
V/µs
V/µs
MHz
MHz
Ω
mA
±11.0
110
110
5.0
3.5
2.0
±12.0
±10.5
11.0
4.5
50
11
nA
nA
1028fd
For more information www.linear.com/LT1028
3
LT1028/LT1128
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the operating
temperature range –55°C ≤ TA ≤ 125°C. VS = ±15V, unless otherwise noted.
LT1028AM
LT1128AM
SYMBOL
PARAMETER
CONDITIONS
VOS
∆VOS
∆Temp
IOS
IB
Input Offset Voltage
Average Input Offset Drift
(Note 2)
(Note 8)
l
MIN
VCM = 0V
VCM = 0V
l
CMRR
PSRR
AVOL
Input Offset Current
Input Bias Current
Input Voltage Range
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
VOUT
IS
Maximum Output Voltage Swing
Supply Current
l
VCM = ±10.3V
VS = ±4.5V to ±16V
RL ≥ 2k, VO = ±10V
RL ≥ 1k, VO = ±10V
RL ≥ 2k
TYP
MAX
TYP
MAX
UNITS
30
0.2
120
0.8
45
0.25
180
1.0
µV
µV/°C
25
±40
±11.7
122
130
14.0
10.0
±11.6
8.7
90
±150
30
±50
±11.7
120
130
14.0
10.0
±11.6
9.0
180
±300
nA
nA
V
dB
dB
V/µV
V/µV
V
mA
l
l
l
l
l
l
±10.3
106
110
3.0
2.0
±10.3
l
LT1028M
LT1128M
MIN
±10.3
100
104
2.0
1.5
±10.3
11.5
13.0
The l denotes the specifications which apply over the operating temperature range 0°C ≤ TA ≤ 70°C. VS = ±15V, unless otherwise
noted.
LT1028AC
LT1128AC
SYMBOL
PARAMETER
CONDITIONS
VOS
Input Offset Voltage
(Note 2)
l
15
∆VOS
∆Temp
Average Input Offset Drift
(Note 8)
l
0.1
IOS
Input Offset Current
VCM = 0V
l
15
IB
Input Bias Current
VCM = 0V
l
±30
Input Voltage Range
CMRR
Common Mode Rejection Ratio
VCM= ±10.5V
MIN
TYP
LT1028C
LT1128C
MAX
MIN
TYP
MAX
UNITS
80
30
125
µV
0.8
0.2
1.0
µV/°C
65
22
130
nA
±120
±40
±240
nA
l
±10.5
±12.0
±10.5
±12.0
V
l
110
124
106
124
dB
PSRR
Power Supply Rejection Ratio
VS = ±4.5V to ±18V
l
114
132
107
132
dB
AVOL
Large-Signal Voltage Gain
RL ≥ 2k, VO = ±10V
RL ≥ 1k, VO = ±10V
l
5.0
4.0
25.0
18.0
3.0
2.5
25.0
18.0
V/µV
V/µV
VOUT
Maximum Output Voltage Swing
RL ≥ 2k
RL ≥ 600Ω (Note 10)
l
±11.5
±9.5
±12.7
±11.0
±11.5
±9.0
±12.7
±10.5
V
V
IS
Supply Current
l
8.0
10.5
8.2
11.5
mA
1028fd
4
For more information www.linear.com/LT1028
LT1028/LT1128
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the operating
temperature range –40°C ≤ TA ≤ 85°C. VS = ±15V, unless otherwise noted. (Note 11)
LT1028AC
LT1128AC
SYMBOL
PARAMETER
VOS
Input Offset Voltage
∆VOS
∆Temp
Average Input Offset Drift
IOS
IB
CONDITIONS
MIN
TYP
l
20
(Note 8)
l
0.2
Input Offset Current
VCM = 0V
l
20
Input Bias Current
VCM = 0V
l
±35
LT1028C
LT1128C
MAX
MIN
TYP
MAX
UNITS
95
35
150
µV
0.8
0.25
1.0
µV/°C
80
28
160
nA
±140
±45
±280
nA
±10.4
±11.8
±10.4
±11.8
V
CMRR
Common Mode Rejection Ratio
VCM = ±10.5V
l
108
123
102
123
dB
PSRR
Power Supply Rejection Ratio
VS = ±4.5V to ±18V
l
112
131
106
131
dB
AVOL
Large-Signal Voltage Gain
RL ≥ 2k, VO = ±10V
RL ≥ 1k, VO = ±10V
l
4.0
3.0
20.0
14.0
2.5
2.0
20.0
14.0
V/µV
V/µV
VOUT
Maximum Output Voltage Swing
RL ≥ 2k
l
±11.0
±12.5
±11.0
±12.5
IS
Supply Current
Input Voltage Range
l
l
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Input Offset Voltage measurements are performed by automatic
test equipment approximately 0.5 sec. after application of power. In
addition, at TA = 25°C, offset voltage is measured with the chip heated
to approximately 55°C to account for the chip temperature rise when the
device is fully warmed up.
Note 3: Long Term Input Offset Voltage Stability refers to the average
trend line of Offset Voltage vs Time over extended periods after the first 30
days of operation. Excluding the initial hour of operation, changes in VOS
during the first 30 days are typically 2.5µV.
Note 4: This parameter is tested on a sample basis only.
Note 5: 10Hz noise voltage density is sample tested on every lot with the
exception of the S8 and S16 packages. Devices 100% tested at 10Hz are
available on request.
8.5
11.0
8.7
V
12.5
mA
Note 6: Current noise is defined and measured with balanced source
resistors. The resultant voltage noise (after subtracting the resistor noise
on an RMS basis) is divided by the sum of the two source resistors to
obtain current noise. Maximum 10Hz current noise can be inferred from
100% testing at 1kHz.
Note 7: Gain-bandwidth product is not tested. It is guaranteed by design
and by inference from the slew rate measurement.
Note 8: This parameter is not 100% tested.
Note 9: The inputs are protected by back-to-back diodes. Current-limiting
resistors are not used in order to achieve low noise. If differential input
voltage exceeds ±1.8V, the input current should be limited to 25mA.
Note 10: This parameter guaranteed by design, fully warmed up at TA
= 70°C. It includes chip temperature increase due to supply and load
currents.
Note 11: The LT1028/LT1128 are designed, characterized and expected to
meet these extended temperature limits, but are not tested at –40°C and
85°C. Guaranteed I-grade parts are available. Consult factory.
1028fd
For more information www.linear.com/LT1028
5
LT1028/LT1128
TYPICAL PERFORMANCE CHARACTERISTICS
10Hz Voltage Noise Distribution
180
120
RMS VOLTAGE NOISE (µV)
140
NUMBER OF UNITS
10
VS = ±15V
TA = 25°C
500 UNITS
MEASURED
FROM 4 RUNS
158
148
160
Wideband Voltage Noise
(0.1Hz to Frequency Indicated)
Wideband Noise, DC to 20kHz
100
80
70
57
60
40
28
20
0
8
0.6
74 3
2 2 2 12
3 21 1
0.8 1.0 1.2 1.4 1.6 1.8 2.0
VOLTAGE NOISE DENSITY (nV/√Hz)
VERTICAL SCALE = 0.5µV/DIV
HORIZONTAL SCALE = 0.5ms/DIV
1
VS = ±15V
TA = 25°C
1
0.1
1028 G02
0.01
100
2.2
1k
100k
10k
BANDWIDTH (Hz)
10M
1M
1028 G03
1028 G01
Total Noise vs Matched Source
Resistance
Total Noise vs Unmatched Source
Resistance
+
10
AT 10Hz
1
AT 1kHz
2 RS NOISE ONLY
VS = ±15V
TA = 25°C
1
3
10 30 100 300 1k 3k
MATCHED SOURCE RESISTANCE (Ω)
10k
10
AT 1kHz
AT 10Hz
1
0.1
2 RS NOISE ONLY
VS = ±15V
TA = 25°C
1
VS = ±15V
TA = 25°C
1/f CORNER = 250Hz
10
1028 G07
10
100
1k
FREQUENCY (Hz)
0
20
1028 G06
RMS VOLTAGE DENSITY (nV/√Hz)
60
40
TIME (SEC)
10k
Voltage Noise vs Temperature
10nV
8
TYPICAL
1
2.0
VS = ±15V
TA = 25°C
6
4
TIME (SEC)
1/f CORNER = 800Hz
0.01Hz to 1Hz Voltage Noise
10nV
MAXIMUM
1028 G05
0.1Hz to 10Hz Voltage Noise
2
10
0.1
10 30 100 300 1k 3k 10k
3
UNMATCHED SOURCE RESISTANCE (Ω)
1028 G04
0
CURRENT NOISE DENSITY (pA/√Hz)
RS
100
RS
–
TOTAL NOISE DENSITY (nV/√Hz)
TOTAL NOISE DENSITY (nV/√Hz)
RS
0.1
Current Noise Spectrum
100
100
80
100
1028 G08
VS = ±15V
1.6
1.2
0.8
AT 10Hz
AT 1kHz
O.4
0
–50 –25
50
25
0
75
TEMPERATURE (°C)
100
125
1028 G09
1028fd
6
For more information www.linear.com/LT1028
LT1028/LT1128
TYPICAL PERFORMANCE CHARACTERISTICS
Distribution of Input Offset
Voltage
50
VS = ±15V
TA = 25°C
800 UNITS TESTED
FROM FOUR RUNS
16
40
14
UNITS (%)
10
12
10
8
6
20
10
0
–10
–20
4
–30
2
–40
0
–50 –40 –30 –20 –10 0 10 20 30 40 50
OFFSET VOLTAGE (µV)
–50
–50 –25
METAL CAN (H) PACKAGE
8
50
25
0
75
TEMPERATURE (°C)
100
DUAL-IN-LINE PACKAGE
PLASTIC (N) OR CERDIP (J)
0
1
2
3
4
TIME AFTER POWER ON (MINUTES)
50
30
BIAS CURRENT
10
OFFSET CURRENT
50
25
75
0
TEMPERATURE (°C)
SUPPLY CURRENT (mA)
RMS VOLTAGE NOISE DENSITY (nV/√Hz)
AT 1kHz
0.75
100
125
±5
±10
±15
SUPPLY VOLTAGE (V)
20
0
–20
–40
±20
1028 G16
NEGATIVE INPUT CURRENT
(OVERCANCELLED) DEVICE
–80
–15
10
5
–10
0
–5
COMMON MODE INPUT VOLTAGE (V)
1028 G15
10
50
9
40
VS = ±15V
7
6
VS = ±5V
5
4
30
125
1028 G17
125°C
0
–10
–40
100
VS = ±15V
10
–30
50
25
0
75
TEMPERATURE (°C)
–50°C
25°C
20
–20
3
0
–50 –25
15
Output Short-Circuit Current
vs Time
2
0
POSITIVE INPUT CURRENT
(UNDERCANCELLED) DEVICE
–60
1
0.5
60
40
Supply Current vs Temperature
8
5
RCM = 20V ª 300MΩ VS = ±15V
TA = 25°C
65nA
80
1028 G14
TA = 25°C
1.0
4
100
20
Voltage Noise vs Supply Voltage
AT 10Hz
3
2
TIME (MONTHS)
Bias Current Over the Common
Mode Range
40
0
–50 –25
5
1.25
1
0
1028 G12
VS = ±15V
VCM = 0V
1028 G13
1.5
125
SHORT-CIRCUIT CURRENT (mA)
SINKING
SOURCING
0
–4
–6
–10
INPUT BIAS CURRENT (nA)
INPUT BIAS AND OFFSET CURRENTS (nA)
CHANGE IN OFFSET VOLTAGE (µV)
60
16
4
0
–2
Input Bias and Offset Currents
Over Temperature
VS = ±15V
TA = 25°C
12
2
1028 G11
Warm-Up Drift
20
4
–8
1028 G10
24
VS = ±15V
8 TA = 25°C
t = 0 AFTER 1 DAY PRE-WARM UP
6
VS = ±15V
30
OFFSET VOLTAGE (µV)
18
Long-Term Stability of Five
Representative Units
OFFSET VOLTAGE CHANGE (µV)
20
Offset Voltage Drift with Temperature
of Representative Units
125°C
25°C
–50°C
–50
3
2
0
1
TIME FROM OUTPUT SHORT TO GROUND (MINUTES)
1028 G18
1028fd
For more information www.linear.com/LT1028
7
LT1028/LT1128
TYPICAL PERFORMANCE CHARACTERISTICS
LT1028
Gain, Phase vs Frequency
Voltage Gain vs Frequency
60
40
50
50
60
40
40
30
30
GAIN
20
20
10
20
0
0
–20
0.01 0.1 1
10 100 1k 10k 100k 1M 10M 100M
FREQUENCY (Hz)
10
VS = ±15V
TA = 25°C
CL = 10pF
–10
10k
100k
1M
10M
FREQUENCY (Hz)
LT1028
60
60
70
PHASE
10
1
FREQUENCY (Hz)
40
30
30
20
20
GAIN
10
VS = ±15V
TA = 25°C
CL = 10pF
–10
10k
100
VOLTAGE GAIN (V/µV)
VOLTAGE GAIN (V/µV)
100
RL = 2k
RL = 600Ω
20
1028 G25
100
1000
CAPACITIVE LOAD (pF)
100k
–
+
50
40
CL
AV = –1, RS = 2k
30
AV = –10
RS = 200Ω
10
–10
100M
1M
10M
FREQUENCY (Hz)
2k
RS
20
0
0
AV = –100, RS = 20Ω
10
VS = ±15V
TA = 25°C
VO = 10mVP-P
100
1000
CAPACITIVE LOAD (pF)
Maximum Undistorted Output
vs Frequency
1
30
TA = 25°C
TA = 125°C
10
ILMAX = 35mA AT –55°C
= 27mA AT 25°C
= 16mA AT 125°C
0.1
1
LOAD RESISTANCE (kΩ)
10000
1028 G24
VS = ±15V
TA = –55°C
10000
30pF
60
Voltage Gain vs Load Resistance
TA = 25°C
5
10
15
SUPPLY VOLTAGE (V)
10
VS = ±15V
TA = 25°C
1028 G23
Voltage Gain vs Supply Voltage
0
50
40
1028 G22
1
AV = –100
RS = 20Ω
LT1128
Capacitance Load Handling
80
0
GAIN ERROR = CLOSED-LOOP GAIN
OPEN-LOOP GAIN
10
AV = –10
RS = 200Ω
1028 G21
70
10
100
0
CL
AV = –1, RS = 2k
30
70
50
LT1128
VOLTAGE GAIN (dB)
GAIN ERROR (%)
TYPICAL
PRECISION
OP AMP
0.1
40
10
–10
100M
–
+
50
LT1128
Gain Phase vs Frequency
1
0.001
2k
RS
1028 G20
Gain Error vs Frequency
Closed-Loop Gain = 1000
0.01
30pF
20
0
1028 G19
0.1
OVERSHOOT (%)
80
LT1028
70
OVERSHOOT (%)
LT1128
60
10
1028 G26
PEAK-TO-PEAK OUTPUT VOLTAGE (V)
100
80
PHASE MARGIN (DEG)
120
70
PHASE
60
VOLTAGE GAIN (dB)
140
VOLTAGE GAIN (dB)
70
VS = ±15V
TA = 25°C
RL = 2k
PHASE MARGIN (DEG)
160
LT1028
Capacitance Load Handling
VS = ±15V
TA = 25°C
RL = 2k
25
20
15
LT1128
LT1028
10
5
10k
100k
1M
FREQUENCY (Hz)
10M
1028 G27
1028fd
8
For more information www.linear.com/LT1028
LT1028/LT1128
TYPICAL PERFORMANCE CHARACTERISTICS
LT1028
Large-Signal Transient Response
LT1028
Slew Rate, Gain-Bandwidth
Product Over Temperature
LT1028
Small-Signal Transient Response
50mV
5V/DIV
20mV/DIV
–10V
17
SLEW RATE (V/µs)
10V
–50mV
1028 G28
1µs/DIV
AV = –1, RS = RF = 2k, CF = 15pF
90
VS = ±15V
0.2µs/DIV
AV = –1, RS = RF = 2k,
CF = 15pF, CL = 80pF
1028 G29
80
GBW
16
FALL
70
15
RISE
60
14
50
13
40
12
–50 –25
50
25
75
0
TEMPERATURE (°C)
100
30
125
GAIN-BANDWIDTH PRODUCT (fO = 20kHz), (MHz)
18
1028 G30
LT1128
Small-Signal Transient Response
9
FALL
8
50mV
0V
0V
–10V
–50mV
7
RISE
6
SLEW RATE (V/µs)
10V
30
GBW
5
4
20
3
2
1028 G31
2µs/DIV
AV = –1, RS = RF = 2k, CF = 30pF
0.2µs/DIV
1028 G32
10
1
AV = –1, CL = 10pF
0
–50
–25
75
50
25
0
TEMPERATURE (°C)
100
125
GAIN-BANDWIDTH PRODUCT (fO = 200kHz), (MHz)
LT1128
Large-Signal Transient Response
LT1128
Slew Rate, Gain-Bandwidth
Product Over Temperature
1028 G33
LT1128
Slew Rate, Gain-Bandwidth Product
vs Over-Compensation Capacitor
Closed-Loop Output Impedance
100
10
10k
LT1128
GBW
10
SLEW RATE
1
10
SLEW
10
100
1k
1
100
AV = 5
COC FROM PIN 5 TO PIN 6
VS = ±15V
TA = 25°C
LT1028
0.001
GBW
GAIN AT 20kHz
0.1
0.01
100
SLEW RATE (V/µs)
LT1028
AV = 1000
1
1k
LT1128
SLEW RATE (V/µs)
10
100
IO = 1mA
VS = ±15V
TA = 25°C
GAIN AT 200kHz
OUTPUT IMPEDANCE (Ω)
100
LT1028
Slew Rate, Gain-Bandwidth Product
vs Over-Compensation Capacitor
10k
1k
FREQUENCY (Hz)
100k
1M
1028 G34
0.1
1
1
10
100
1000
10000
OVER-COMPENSATION CAPACITOR (pF)
1028 G35
0.1
1
10
10
100
1000
10000
OVER-COMPENSATION CAPACITOR (pF)
1028 G36
1028fd
For more information www.linear.com/LT1028
9
LT1028/LT1128
TYPICAL PERFORMANCE CHARACTERISTICS
140
–3
VS = ±15V
–4
4
3
VS = ±5V TO ±15V
2
1
V–
50
25
0
75
TEMPERATURE (°C)
–50 –25
100
120
100
LT1128
LT1028
80
60
40
20
0
125
10
100k
10k
1k
FREQUENCY (Hz)
100
0.1
AV = –1000
RL = 2k
AV = 1000
RL = 600Ω
VO = 20VP-P
VS = ±15V
TA = 25°C
10
FREQUENCY (kHz)
1
100
TOTAL HARMONIC DISTORTION (%)
TOTAL HARMONIC DISTORTION (%)
AV = 1000
RL = 600Ω
VO = 20VP-P
f = 1kHz
VS = ±15V
TA = 25°C
RL = 10k
0.01
INVERTING
GAIN
0.001
0.0001
MEASURED
EXTRAPOLATED
100
1k
10k
CLOSED LOOP GAIN
10
0.1
VO = 20VP-P
VS = ±15V
TA = 25°C
10
FREQUENCY (kHz)
100
TOTAL HARMONIC DISTORTION (%)
TOTAL HARMONIC DISTORTION (%)
AV = 1000
RL = 600Ω
AV = 1000
RL = 609Ω
1.0
20
1
10
100 1k 10k 100k 1M 10M
FREQUENCY (Hz)
1028 G39
100k
1.0
0.1
10k
100k
FREQUENCY (Hz)
1M
1028 G42
1028 G41
AV = –1000
RL = 2k
0.001
40
LT1128
Total Harmonic Distortion vs
Closed-Loop Gain
1.0
0.01
60
High Frequency Voltage Noise
vs Frequency
NON-INVERTING
GAIN
1028 G40
0.1
POSITIVE
SUPPLY
80
10
LT1128
Total Harmonic Distortion vs
Frequency and Load Resistance
AV = 1000
RL = 2k
NEGATIVE
SUPPLY
100
1028 G38
0.1
0.001
120
LT1028
Total Harmonic Distortion vs
Closed-Loop Gain
AV = 1000
RL = 2k
VS = ±15V
TA = 25°C
140
0
0.1
10M
1M
1028 G37
LT1028
Total Harmonic Distortion vs
Frequency and Load Resistance
0.01
POWER SUPPLY REJECTION RATIO (dB)
VS = ±5V
160
VS = ±15V
TA = 25°C
NOISE VOLTAGE DENSITY (nV/√Hz)
COMMON MODE LIMIT (V)
REFERRED TO POWER SUPPLY
–1
–2
Power Supply Rejection Ratio
vs Frequency
Common Mode Rejection Ratio
vs Frequency
COMMON MODE REJECTION RATIO (dB)
V+
Common Mode Limit Over
Temperature
0.01
VO = 20VP-P
f = 1kHz
VS = ±15V
TA = 25°C
RL = 10k
INVERTING
GAIN
0.001
0.0001
NON-INVERTING
GAIN
MEASURED
EXTRAPOLATED
10
1028 G43
100
1k
10k
CLOSED LOOP GAIN
100k
1028 G44
1028fd
10
For more information www.linear.com/LT1028
LT1028/LT1128
APPLICATIONS INFORMATION – NOISE
Voltage Noise vs Current Noise
The LT1028/LT1128’s less than 1nV/√Hz voltage noise is
three times better than the lowest voltage noise heretofore
available (on the LT1007/1037). A necessary condition for
such low voltage noise is operating the input transistors at
nearly 1mA of collector currents, because voltage noise is
inversely proportional to the square root of the collector
current. Current noise, however, is directly proportional
to the square root of the collector current. Consequently,
the LT1028/LT1128’s current noise is significantly higher
than on most monolithic op amps.
Therefore, to realize truly low noise performance it is
important to understand the interaction between voltage
noise (en), current noise (In) and resistor noise (rn).
Total Noise vs Source Resistance
The total input referred noise of an op amp is given by:
et = [en2 + rn2 + (InReq)2]1/2
where Req is the total equivalent source resistance at the
two inputs, and
rn = √4kTReq = 0.13√Req in nV/√Hz at 25°C
As a numerical example, consider the total noise at 1kHz
of the gain 1000 amplifier shown in Figure 1.
100Ω
The plot also shows that current noise is more dominant
at low frequencies, such as 10Hz. This is because resistor
noise is flat with frequency, while the 1/f corner of current
noise is typically at 250Hz. At 10Hz when Req > 1k, the
current noise term will exceed the resistor noise.
When the source resistance is unmatched, the total noise
versus unmatched source resistance plot should be consulted. Note that total noise is lower at source resistances
below 1k because the resistor noise contribution is less.
When RS > 1k total noise is not improved, however. This
is because bias current cancellation is used to reduce
input bias current. The cancellation circuitry injects two
correlated current noise components into the two inputs.
With matched source resistors the injected current noise
creates a common-mode voltage noise and gets rejected
by the amplifier. With source resistance in one input only,
the cancellation noise is added to the amplifier’s inherent
noise.
In summary, the LT1028/LT1128 are the optimum amplifiers for noise performance, provided that the source
resistance is kept low. The following table depicts which op
amp manufactured by Linear Technology should be used
to minimize noise, as the source resistance is increased
beyond the LT1028/LT1128’s level of usefulness.
100k
–
100Ω
the largest term, as in the example above, and the LT1028/
LT1128’s voltage noise becomes negligible. As Req is
further increased, current noise becomes important. At
1kHz, when Req is in excess of 20k, the current noise
component is larger than the resistor noise. The total
noise versus matched source resistance plot illustrates
the above calculations.
LT1028
LT1128
+
1028 F01
Table 1. Best Op Amp for Lowest Total Noise vs Source Resistance
Figure 1
Req = 100Ω + 100Ω || 100k ≈ 200Ω
rn = 0.13√200 = 1.84nV√Hz
en = 0.85nV√Hz
In = 1.0pA/√Hz
et = [0.852 + 1.842 + (1.0 × 0.2)2]1/2 = 2.04nV/√Hz
Output noise = 1000 et = 2.04µV/√Hz
At very low source resistance (Req < 40Ω) voltage noise
dominates. As Req is increased resistor noise becomes
BEST OP AMP
SOURCE RESISTANCE (Ω) (Note 1)
AT LOW FREQ (10Hz)
WIDEBAND (1kHz)
0 to 400
LT1028/LT1128
LT1028/LT1128
400 to 4k
LT1007/1037
LT1028/LT1128
4k to 40k
LT1001
LT1007/LT1037
40k to 500k
LT1012
LT1001
500k to 5M
LT1012 or LT1055
LT1012
>5M
LT1055
LT1055
Note 1: Source resistance is defined as matched or unmatched, e.g.,
RS = 1k means: 1k at each input, or 1k at one input and zero at the other.
1028fd
For more information www.linear.com/LT1028
11
LT1028/LT1128
APPLICATIONS INFORMATION – NOISE
Noise Testing – Voltage Noise
The LT1028/LT1128’s RMS voltage noise density can be
accurately measured using the Quan Tech Noise Analyzer,
Model 5173 or an equivalent noise tester. Care should be
taken, however, to subtract the noise of the source resistor
used. Prefabricated test cards for the Model 5173 set the
device under test in a closed-loop gain of 31 with a 60Ω
source resistor and a 1.8k feedback resistor. The noise
of this resistor combination is 0.13√58 = 1.0nV/√Hz. An
LT1028/LT1128 with 0.85nV/√Hz noise will read (0.852 +
1.02)1/2 = 1.31nV/√Hz. For better resolution, the resistors
should be replaced with a 10Ω source and 300Ω feedback
resistor. Even a 10Ω resistor will show an apparent noise
which is 8% to 10% too high.
The 0.1Hz to 10Hz peak-to-peak noise of the LT1028/
LT1128 is measured in the test circuit shown. The frequency response of this noise tester indicates that the
0.1Hz corner is defined by only one zero. The test time
to measure 0.1Hz to 10Hz noise should not exceed 10
seconds, as this time limit acts as an additional zero to
eliminate noise contributions from the frequency band
below 0.1Hz.
Measuring the typical 35nV peak-to-peak noise performance of the LT1028/LT1128 requires special test
precautions:
(a)The device should be warmed up for at least five
minutes. As the op amp warms up, its offset voltage
changes typically 10µV due to its chip temperature
increasing 30°C to 40°C from the moment the power
supplies are turned on. In the 10 second measurement
interval these temperature-induced effects can easily
exceed tens of nanovolts.
(b)For similar reasons, the device must be well shielded
from air current to eliminate the possibility of thermoelectric effects in excess of a few nanovolts, which
would invalidate the measurements.
(c)Sudden motion in the vicinity of the device can also
feedthrough to increase the observed noise.
A noise-voltage density test is recommended when measuring noise on a large number of units. A 10Hz noise-voltage
density measurement will correlate well with a 0.1Hz to
10Hz peak-to-peak noise reading since both results are
determined by the white noise and the location of the 1/f
corner frequency.
0.1µF
100
90
100k
10Ω
+
2k
*
4.7µF
+
LT1001
–
100k
VOLTAGE GAIN = 50,000
24.3k
* DEVICE UNDER TEST
4.3k
2.2µF
22µF
SCOPE
×1
RIN = 1M
110k
GAIN (dB)
80
–
70
60
50
40
0.1µF
NOTE ALL CAPACITOR VALUES ARE FOR
NONPOLARIZED CAPACITORS ONLY
1028 F02
30
0.01
0.1
1.0
10
FREQUENCY (Hz)
100
1028 F03
Figure 2. 0.1Hz to 10Hz Noise Test Circuit
Figure 3. 0.1Hz to 10Hz Peak-to-Peak
Noise Tester Frequency Response
1028fd
12
For more information www.linear.com/LT1028
LT1028/LT1128
APPLICATIONS INFORMATION – NOISE
Noise Testing – Current Noise
Current noise density (In) is defined by the following formula, and can be measured in the circuit shown in Figure 4.
(
)
e 2 − 31• 18.4nV/ Hz 2 
 no

ln = 
20k • 31
1/2
1.8k
10k
60Ω
10k
10Hz voltage noise density is sample tested on every lot.
Devices 100% tested at 10Hz are available on request for
an additional charge.
10Hz current noise is not tested on every lot but it can be
inferred from 100% testing at 1kHz. A look at the current
noise spectrum plot will substantiate this statement. The
only way 10Hz current noise can exceed the guaranteed
limits is if its 1/f corner is higher than 800Hz and/or its
white noise is high. If that is the case then the 1kHz test
will fail.
–
LT1028
LT1128
eno
10
+
1028 F04
Figure 4
If the Quan Tech Model 5173 is used, the noise reading is
input-referred, therefore the result should not be divided
by 31; the resistor noise should not be multiplied by 31.
100% Noise Testing
The 1kHz voltage and current noise is 100% tested on
the LT1028/LT1128 as part of automated testing; the
approximate frequency response of the filters is shown.
The limits on the automated testing are established by
extensive correlation tests on units measured with the
Quan Tech Model 5173.
NOISE FILTER LOSS (dB)
0
–10
–20
–30
CURRENT
NOISE
VOLTAGE
NOISE
–40
–50
100
1k
10k
100k
FREQUENCY (Hz)
1028 F05
Figure 5. Automated Tester Noise Filter
1028fd
For more information www.linear.com/LT1028
13
LT1028/LT1128
APPLICATIONS INFORMATION
General
10k*
15V
The LT1028/LT1128 series devices may be inserted directly
into OP-07, OP-27, OP-37, LT1007 and LT1037 sockets
with or without removal of external nulling components. In
addition, the LT1028/LT1128 may be fitted to 5534 sockets
with the removal of external compensation components.
2
200Ω*
10k*
The input offset voltage of the LT1028/LT1128 and its drift
with temperature, are permanently trimmed at wafer testing to a low level. However, if further adjustment of VOS is
necessary, the use of a 1k nulling potentiometer will not
degrade drift with temperature. Trimming to a value other
than zero creates a drift of (VOS/300)µV/°C, e.g., if VOS
is adjusted to 300µV, the change in drift will be 1µV/°C.
The adjustment range with a 1k pot is approximately
±1.1mV.
1k
INPUT
3
+
VO
4
–15V
Unity-Gain Buffer Applications (LT1128 Only)
When RF ≤ 100Ω and the input is driven with a fast, largesignal pulse (>1V), the output waveform will look as shown
in the pulsed operation diagram (Figure 8).
RF
OUTPUT
7 6
6V/µs
+
OUTPUT
1028 F08
4
–15V
1028 F07
–
15V
8
LT1028
LT1128
+
6
Figure 7. Test Circuit for Offset Voltage
and Offset Voltage Drift with Temperature
1
–
7
LT1028
LT1128
VO = 100VOS
* RESISTORS MUST HAVE LOW
THERMOELECTRIC POTENTIAL
Offset Voltage Adjustment
2
3
–
Figure 8
1028 F06
Figure 6
Offset Voltage and Drift
Thermocouple effects, caused by temperature gradients
across dissimilar metals at the contacts to the input terminals, can exceed the inherent drift of the amplifier unless
proper care is exercised. Air currents should be minimized,
package leads should be short, the two input leads should
be close together and maintained at the same temperature.
The circuit shown in Figure 7 to measure offset voltage
is also used as the burn-in configuration for the LT1028/
LT1128.
During the fast feedthrough-like portion of the output, the
input protection diodes effectively short the output to the
input and a current, limited only by the output short-circuit
protection, will be drawn by the signal generator. With
RF ≥ 500Ω, the output is capable of handling the current
requirements (IL ≤ 20mA at 10V) and the amplifier stays
in its active mode and a smooth transition will occur.
As with all operational amplifiers when RF > 2k, a pole will
be created with RF and the amplifier’s input capacitance,
creating additional phase shift and reducing the phase
margin. A small capacitor (20pF to 50pF) in parallel with
RF will eliminate this problem.
1028fd
14
For more information www.linear.com/LT1028
LT1028/LT1128
APPLICATIONS INFORMATION
Frequency Response
C1
The LT1028’s Gain, Phase vs Frequency plot indicates that
the device is stable in closed-loop gains greater than +2 or
–1 because phase margin is about 50° at an open-loop gain
of 6dB. In the voltage follower configuration phase margin
seems inadequate. This is indeed true when the output is
shorted to the inverting input and the noninverting input
is driven from a 50Ω source impedance. However, when
feedback is through a parallel R-C network (provided CF
< 68pF), the LT1028 will be stable because of interaction
between the input resistance and capacitance and the
feedback network. Larger source resistance at the noninverting input has a similar effect. The following voltage
follower configurations are stable:
33pF
2k
–
R1
RS1
RS2
–
LT1028
+
1028 F10
Figure 10
If CF is only used to cut noise bandwidth, a similar effect
can be achieved using the over-compensation terminal.
The Gain, Phase plot also shows that phase margin is
about 45° at gain of 10 (20dB). The following configuration
has a high (≈70%) overshoot without the 10pF capacitor
because of additional phase shift caused by the feedback
resistor – input capacitance pole. The presence of the 10pF
capacitor cancels this pole and reduces overshoot to 5%.
–
LT1028
500Ω
+
50Ω
10pF
LT1028
+
10k
1.1k
50Ω
–
LT1028
+
1028 F09
Figure 9
50Ω
Another configuration which requires unity-gain stability
is shown below. When CF is large enough to effectively
short the output to the input at 15MHz, oscillations can
occur. The insertion of RS2 ≥ 500Ω will prevent the LT1028
from oscillating. When RS1 ≥ 500Ω, the additional noise
contribution due to the presence of RS2 will be minimal.
When RS1 ≤ 100Ω, RS2 is not necessary, because RS1
represents a heavy load on the output through the CF
short. When 100Ω < RS1 < 500Ω, RS2 should match RS1.
For example, RS1 = RS2 = 300Ω will be stable. The noise
increase due to RS2 is 40%.
1028 F11
Figure 11
Over-Compensation
The LT1028/LT1128 are equipped with a frequency overcompensation terminal (Pin 5). A capacitor connected
between Pin 5 and the output will reduce noise bandwidth.
Details are shown on the Slew Rate, Gain-Bandwidth Product vs Over-Compensation Capacitor plot. An additional
benefit is increased capacitive load handling capability.
1028fd
For more information www.linear.com/LT1028
15
LT1028/LT1128
TYPICAL APPLICATIONS
Strain Gauge Signal Conditioner with Bridge Excitation
15V
LT1021-5
3
5.0V
+
2
–
7
330Ω
6
LT1128
4
–15V
REFERENCE
OUTPUT
350Ω
BRIDGE
3
301k*
10k
ZERO
TRIM
2
7
–
2
7
–
+
+
0V TO 10V
OUTPUT
1µF
30.1k*
5k
GAIN
TRIM
49.9Ω*
4
–15V
*RN60C FILM RESISTORS
6
LT1028
6
LT1028
15V
3
15V
330Ω
4
THE LT1028’s NOISE CONTRIBUTION IS NEGLIGIBLE
COMPARED TO THE BRIDGE NOISE.
–15V
1028 TA03
Low Noise Voltage Regulator
28V
IN
LT317A
10µF
10µF
+
OUT
121Ω
PROVIDES PRE-REG
AND CURRENT
LIMITING
28V
LT1021-10
1k
+
LT1028
2.32k
ADJ
330Ω
2N6387
–
1000pF
20V OUTPUT
2k
2k
1028 TA04
1028fd
16
For more information www.linear.com/LT1028
LT1028/LT1128
TYPICAL APPLICATIONS
Paralleling Amplifiers to Reduce Voltage Noise
+
A1
LT1028
1.5k
–
7.5Ω
470Ω
4.7k
+
A2
LT1028
1.5k
–
–
7.5Ω
LT1028
+
An
LT1028
OUTPUT
+
470Ω
1.5k
–
7.5Ω
470Ω
1. ASSUME VOLTAGE NOISE OF LT1028 AND 7.5Ω SOURCE RESISTOR = 0.9nV/√Hz.
2. GAIN WITH n LT1028s IN PARALLEL = n • 200.
3. OUTPUT NOISE = √n • 200 • 0.9nV/√Hz.
OUTPUT NOISE 0.9
4. INPUT REFERRED NOISE =
=
nV/√Hz.
n • 200
√n
5. NOISE CURRENT AT INPUT INCREASES √n TIMES.
2µV
6. IF n = 5, GAIN = 1000, BANDWIDTH = 1MHz, RMS NOISE, DC TO 1MHz =
= 0.9µV.
√5
1028 TA05
1028fd
For more information www.linear.com/LT1028
17
LT1028/LT1128
TYPICAL APPLICATIONS
Phono Preamplifier
10Ω
787Ω
15V
2
3
+
0.33µF
6
LT1028
47k
10k
7
–
100pF
0.1µF
OUTPUT
4
–15V
ALL RESISTORS METAL FILM
MAG PHONO
INPUT
1028 TA06
Tape Head Amplifier
499Ω
0.1µF
31.6k
10Ω
2
–
LT1028
TAPE HEAD
INPUT
3
6
OUTPUT
+
ALL RESISTORS METAL FILM
1028 TA07
1028fd
18
For more information www.linear.com/LT1028
LT1028/LT1128
TYPICAL APPLICATIONS
Low Noise, Wide Bandwidth Instrumentation Amplifier
–INPUT
+
300Ω
LT1028
–
820Ω
10k
68pF
50Ω
10Ω
820Ω
–
OUTPUT
LT1028
300Ω
LT1028
+INPUT
–
68pF
+
+
10k
GAIN = 1000, BANDWIDTH = 1MHz
INPUT REFERRED NOISE = 1.5nV/√Hz AT 1kHz
WIDEBAND NOISE –DC to 1MHz = 3µVRMS
IF BW LIMITED TO DC TO 100kHz = 0.55µVRMS
1028 TA08
Gyro Pick-Off Amplifier
GYRO TYPICAL–
NORTHROP CORP.
GR-F5AH7-5B
SINE
DRIVE
+
•
OUTPUT TO SYNC
DEMODULATOR
LT1028
–
1k
100Ω
1028 TA09
1028fd
For more information www.linear.com/LT1028
19
LT1028/LT1128
TYPICAL APPLICATIONS
Super Low Distortion Variable Sine Wave Oscillator
R1
C1
0.047
20Ω
20Ω
C2
0.047
2k
1VRMS OUTPUT
1.5kHz TO 15kHz
1
f=
2πRC
WHERE R1C1 = R2C2
4.7k
15V
+
2k
(
LT1028
R2
–
5.6k
2.4k
)
LT1004-1.2V
10pF
22k
15µF
+
100k
560Ω
LT1055
TRIM FOR
LOWEST
DISTORTION
+
20k
MOUNT 1N4148s
IN CLOSE PROXIMITY
–
2N4338
10k
10k
<0.0018% DISTORTION AND NOISE.
MEASUREMENT LIMITED BY RESOLUTION OF
HP339A DISTORTION ANALYZER
1028 TA10
Chopper-Stabilized Amplifier
15V
1N758
3
7
+
2
LT1052
–
6
8
4
1
0.1
0.1
1N758
0.01
15V
–15V
100k
130Ω
68Ω
1
INPUT
3
2
+
7
LT1028
–
30k
4
8
OUTPUT
10k
–15V
10Ω
1028 TA11
1028fd
20
For more information www.linear.com/LT1028
LT1028/LT1128
SCHEMATIC DIAGRAM
NULL
8
R5
130Ω
NULL
1
V+
7
R6
130Ω
Q4
R2
3k
R1
3k
1.1mA
R10
400Ω
Q16
3
1
Q8
1
Q11
Q1
Q2
R11
100Ω
Q9
Q24
4.5µA
OUTPUT
6
Q25
1.5µA
Q12
Q13
R12
240Ω
Q14
1.5µA
INVERTING
INPUT
2
Q22
C3
250pF
Q10
4.5µA
4.5µA
Q26
Q6
4.5µA
3
R10 C2
500Ω
Q18
Q5
Q7
500µA
R11
400Ω
Q19
900µA
3
NONINVERTING
INPUT
400µA
C1
257pF
Q17
900µA
2.3mA
C4
35pF
Q27
0
1.8mA
BIAS
Q3
Q15
R7
80Ω
V–
4
300µA
R8
480Ω
Q23
Q21
600µA
Q20
1028 TA12
5 OVER-COMP
C2 = 50pF for LT1028
C2 = 275pF for LT1128
1028fd
For more information www.linear.com/LT1028
21
LT1028/LT1128
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LT1028#packaging for the most recent package drawings.
J8 Package
3-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110)
CORNER LEADS OPTION
(4 PLCS)
.023 – .045
(0.584 – 1.143)
HALF LEAD
OPTION
.045 – .068
(1.143 – 1.650)
FULL LEAD
OPTION
.005
(0.127)
MIN
.405
(10.287)
MAX
8
7
6
5
.025
(0.635)
RAD TYP
.220 – .310
(5.588 – 7.874)
1
.300 BSC
(7.62 BSC)
2
3
4
.200
(5.080)
MAX
.015 – .060
(0.381 – 1.524)
.008 – .018
(0.203 – 0.457)
0° – 15°
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
.045 – .065
(1.143 – 1.651)
.014 – .026
(0.360 – 0.660)
.100
(2.54)
BSC
.125
3.175
MIN
J8 0801
OBSOLETE PACKAGE
1028fd
22
For more information www.linear.com/LT1028
LT1028/LT1128
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LT1028#packaging for the most recent package drawings.
N Package
8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510 Rev I)
.400*
(10.160)
MAX
8
7
6
5
1
2
3
4
.255 ±.015*
(6.477 ±0.381)
.300 – .325
(7.620 – 8.255)
.008 – .015
(0.203 – 0.381)
(
+.035
.325 –.015
8.255
+0.889
–0.381
)
.045 – .065
(1.143 – 1.651)
.065
(1.651)
TYP
.100
(2.54)
BSC
.130 ±.005
(3.302 ±0.127)
.120
(3.048) .020
MIN
(0.508)
MIN
.018 ±.003
(0.457 ±0.076)
N8 REV I 0711
NOTE:
1. DIMENSIONS ARE
INCHES
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
1028fd
For more information www.linear.com/LT1028
23
LT1028/LT1128
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LT1028#packaging for the most recent package drawings.
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610 Rev G)
.189 – .197
(4.801 – 5.004)
NOTE 3
.045 ±.005
.050 BSC
8
.245
MIN
.160 ±.005
.010 – .020
× 45°
(0.254 – 0.508)
NOTE:
1. DIMENSIONS IN
5
.150 – .157
(3.810 – 3.988)
NOTE 3
1
RECOMMENDED SOLDER PAD LAYOUT
.053 – .069
(1.346 – 1.752)
0°– 8° TYP
.016 – .050
(0.406 – 1.270)
6
.228 – .244
(5.791 – 6.197)
.030 ±.005
TYP
.008 – .010
(0.203 – 0.254)
7
.014 – .019
(0.355 – 0.483)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
4. PIN 1 CAN BE BEVEL EDGE OR A DIMPLE
2
3
4
.004 – .010
(0.101 – 0.254)
.050
(1.270)
BSC
SO8 REV G 0212
1028fd
24
For more information www.linear.com/LT1028
LT1028/LT1128
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LT1028#packaging for the most recent package drawings.
S Package
16-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610 Rev G)
.386 – .394
(9.804 – 10.008)
NOTE 3
.045 ±.005
.050 BSC
16
N
14
13
12
11
10
9
N
.245
MIN
.160 ±.005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
1
.030 ±.005
TYP
15
2
3
N/2
N/2
RECOMMENDED SOLDER PAD LAYOUT
.010 – .020
× 45°
(0.254 – 0.508)
.008 – .010
(0.203 – 0.254)
1
2
3
4
5
.053 – .069
(1.346 – 1.752)
NOTE:
1. DIMENSIONS IN
.014 – .019
(0.355 – 0.483)
TYP
7
8
.004 – .010
(0.101 – 0.254)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
6
.050
(1.270)
BSC
S16 REV G 0212
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
4. PIN 1 CAN BE BEVEL EDGE OR A DIMPLE
1028fd
For more information www.linear.com/LT1028
25
LT1028/LT1128
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/product/LT1028#packaging for the most recent package drawings.
H Package
8-Lead TO-5 Metal Can (.230 Inch PCD)
(Reference LTC DWG # 05-08-1321)
.040
(1.016)
MAX
.335 – .370
(8.509 – 9.398)
DIA
.305 – .335
(7.747 – 8.509)
.050
(1.270)
MAX
SEATING
PLANE
.165 – .185
(4.191 – 4.699)
GAUGE
PLANE
.010 – .045*
(0.254 – 1.143)
REFERENCE
PLANE
.500 – .750
(12.700 – 19.050)
.016 – .021**
(0.406 – 0.533)
.027 – .045
(0.686 – 1.143)
45°
.028 – .034
(0.711 – 0.864)
PIN 1
.230
(5.842)
TYP
.110 – .160
(2.794 – 4.064)
INSULATING
STANDOFF
*LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE
AND THE SEATING PLANE
.016 – .024
**FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS
(0.406 – 0.610) H8 (TO-5) 0.230 PCD 0204
OBSOLETE PACKAGE
1028fd
26
For more information www.linear.com/LT1028
LT1028/LT1128
REVISION HISTORY
(Revision history begins at Rev B)
REV
DATE
DESCRIPTION
B
10/12
Replaced the Typical Application.
1
C
10/14
Corrected diagram to show N8 package is not obsolete.
2
Changed TJMAX to 150°C for S8 and SW packages.
2
D
10/15
PAGE NUMBER
Corrected right-hand Electrical Characteristics column to reflect non-A-grade specs.
3
Corrected LM301A and LT1012 input polarity.
28
Corrected component values in Low Noise Voltage Regulator circuit.
16
1028fd
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LT1028
27
LT1028/LT1128
TYPICAL APPLICATION
Low Noise Infrared Detector
5V
10Ω
+
1k
100µF
33Ω
+
SYNCHRONOUS
DEMODULATOR
100µF
10k*
OPTICAL
CHOPPER
WHEEL
5V
5V
1000µF
3
+
IR
RADIATION
10k*
267Ω
39Ω
PHOTOELECTRIC
PICK-OFF
2
2
7
+
LT1028
–
1/4 LTC1043
6
13
8
4
12
10k
–5V
INFRA RED ASSOCIATES, INC.
HgCdTe IR DETECTOR
13Ω AT 77°K
3
–
7
LM301A
+
1
4
14
16
–5V
30pF
5V
6
8
2
1M
3
–
7
LT1012
+
6
8
DC OUT
1
4
10Ω
–5V
1028 TA13
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1806/LT1807
325MHz, 3.5nV/√Hz Single and Dual Op Amps
Slew Rate = 140V/µs, Low Distortion at 5MHz: –80dBc
1028fd
28 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LT1028
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LT1028
LT 1015 REV D • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 1992