C300 Test Data

Sample Test Data
C Series C300
300 W Four Module Multi-Output Power Supply
Table of Contents
General Description
Test Circuit
The C Series are flexible multi-output power supplies that
enable simple combination of various modules.
Features and Benefits
1
Figures
3
Tables
8
Important Information
• High reliability with low noise and low leakage current
• Medical and information equipment approval to
UL60950-1, C-UL, EN60950 and EN60601-1 3rd
• Higher withstand voltage and lower leakage current
• OCP, OVP and OHP, remote sensing, control, and alarm
(AC power fail, fan alarm, and low output)
10
Sample Test Conditions
Input Voltage, VIN
Min.
(V)
Nom.
(V)
85
100
Max.
(V)
240
264
Load Current, ILOAD
Min.
(A)
Nom.
(A)
Max.
(A)
–
–
–
Sample Test Circuit Diagram
4
5
7
A
W
A
6
1
Load
C1
Power
Supply
...
V
3
8
2
A
Load
C1
Key
Description
Remarks
–
Measuring instrument
Output voltage is measured with a digital multimeter
1
Variable autotransformer
–
2
Isolation transformer
–
3
Circuit breaker
–
4
Ammeter
–
5
Watt meter
–
6
Volt meter
–
7
Ammeter
–
8
Shunt resistor
–
Load capacitor
Electrolytic capacitor: 47 μF
Film capacitor: 0.1 μF
C1
CHD40004-001A00-TD
SANKEN ELECTRIC CO., LTD.
http://www.sanken-ele.co.jp/en/
March 8, 2013
C300
List of Figures
1. Input Current
2. Power Factor
3. Efficiency
4. Inrush Current
5. Inrush Current
3
3
4
4
5
6. Leakage Current
7. Start-Up Time
8. Hold-Up Time
9. Conduction Noise 100 V / 250 W
10. Conduction Noise 240 V / 300 W
5
6
6
7
7
List of Tables
1. Input Characteristics
8
Input Current
Input Power
Power Factor
Efficiency
Inrush Current
Leakage Current
Hold-Up Time
2. Environment Tests
3. Noise Tolerance Characteristics
8
AC Line Noise
Lightning Surge
Electrostatic Discharge
4. Other Characteristics
9
Withstand Voltage
Leakage Current at Withstand Voltage
Insulation Resistance
8
Vibration (Non-Operating)
Power-On at High Temperature
Power-On at Low Temperature
Shock
CHD40004-001A00-TD
SANKEN ELECTRIC CO., LTD.
2
March 8, 2013
C300
Figures
Figure 1. Input Current
(By Load Current)
Input Voltage
Output
Temperature
85 to 264 VAC
250 W at 85 to 132 V
300 W at 180 to 264 V
TA = 25°C
Remarks
Configuration: C150S05, C150S12, and two C130X24
4.00
Input Current(A)
3.50
3.00
Vin=85V
2.50
Vin=100V
2.00
Vin=132V
1.50
Vin=180V
1.00
Vin=240V
0.50
Vin=264V
0.00
25%
50%
75%
Load Rate(%)
100%
Figure 2. Power Factor
(By Load Current)
Input Voltage
Output
Temperature
85 to 264 VAC
250 W at 85 to 132 V
300 W at 180 to 264 V
TA = 25°C
Remarks
Configuration: C150S05, C150S12, and two C130X24
1.02
Power Factor
1.00
0.98
Vin=85V
0.96
Vin=100V
0.94
Vin=132V
Vin=180V
0.92
Vin=240V
0.90
Vin=264V
0.88
25%
CHD40004-001A00-TD
50%
75%
Load Rate(%)
100%
SANKEN ELECTRIC CO., LTD.
3
March 8, 2013
C300
Figure 3. Efficiency
(By Load Current)
Input Voltage
Output
Temperature
85 to 264 VAC
250 W at 85 to 132 V
300 W at 180 to 264 V
TA = 25°C
Remarks
Configuration: C150S05, C150S12, and two C130X24
90
Efficiency(%)
85
Vin=85V
80
Vin=100V
Vin=132V
75
Vin=180V
Vin=240V
70
Vin=264V
65
25%
50%
75%
Load Rate(%)
100%
Figure 4. Inrush Current
(By Input Voltage)
Input Voltage
Output
Temperature
100 to 240 VAC
250 W at 120 V
300 W at 240 V
TA = 25°C
Remarks
Cold start
35
Inrush Current(A)
30
25
20
15
10
5
0
100
240
Input Voltage(V)
CHD40004-001A00-TD
SANKEN ELECTRIC CO., LTD.
4
March 8, 2013
C300
Figure 5. Inrush Current
Input Voltage
Output
Temperature
VIN =240 V
300 W
TA = 25°C
Remarks
10 A /div., time = 2 ms /div.
29 A
0A
Figure 6. Leakage Current
(By Load Current)
Input Voltage
Output
Temperature
100 to 240 VAC
250 W at 100 V
300 W at 240 V
TA = 25°C
Remarks
R = 1.5 kΩ, C = 0.15 μF
0.12
0.10
0.08
0.06
0.04
0.02
0.00
100
240
Input Voltage(V)
CHD40004-001A00-TD
SANKEN ELECTRIC CO., LTD.
5
March 8, 2013
C300
Figure 7. Start-Up Time
(By Input Voltage)
Input Voltage
Output
Temperature
85 to 264 VAC
250 W at 85 to 132 V
300 W at 180 to 264 V
TA = –20°C to 50°C
Remarks
Configuration: C150S05, C150S12, and two C130X24
Start - Up Time(ms)
1,000
900
800
700
600
500
400
300
200
100
0
Ta=- 20°C
Ta=25°C
Ta=50°C
85
100
132
180
Input Voltage(V)
240
264
Figure 8. Hold-Up Time
(By Load Rate)
Input Voltage
Output
Temperature
100 to 240 VAC
250 W at 100 V
300 W at 240 V
TA = –20°C to 50°C
Remarks
Configuration: C150S05, C150S12, and two C130X24
Hold up Time(ms)
300
200
Ta=- 20°C Vin=100V
Ta=- 20°C Vin=240V
Ta=25°C Vin=100V
100
Ta=25°C Vin=240V
Ta=50°C Vin=100V
Ta=50°C Vin=240V
0
25%
CHD40004-001A00-TD
50%
75%
Load Rate(%)
100%
SANKEN ELECTRIC CO., LTD.
6
March 8, 2013
C300
Figure 9. Conduction Noise 100 V / 250 W
Output
Temperature
VIN =100 V
250 W
TA = 25°C
Remarks
Configuration: C150S05, C150S12, and two C130X24
RFI Voltage (dBμV)
Input Voltage
Frequency (MHz)
Figure 10. Conduction Noise 240 V / 300 W
Output
Temperature
VIN =240 V
300 W
TA = 25°C
Remarks
Configuration: C150S05, C150S12, and two C130X24
RFI Voltage (dBμV)
Input Voltage
Frequency (MHz)
CHD40004-001A00-TD
SANKEN ELECTRIC CO., LTD.
7
March 8, 2013
C300
Tables
Table 1. Input Characteristics
(At TA = 25°C)
Test Item
Conditions
VIN
ILOAD
Test Results
VIN = 100 V
VIN = 240 V
Specification
Remarks
Input Current
Nom
Nom
3.1 A
1.5 A
–
3.7 A/ 2.0 A
Figure 1
Input Power
Nom
Nom
310 W
360 W
–
–
–
Power Factor
Nom
Nom
0.994
0.986
–
–
Figure 2
Efficiency
Nom
Nom
82.6%
85.5%
–
–
Figure 3
Inrush Current
Nom
Nom
12 A
29 A
–
20 A/ 40 A
Figure 4
0.30 mA/
0.50 mA
Figure 6
10 ms
Figure 8
Specification
Remarks
Frequency = 10 to 55 Hz, Sweep Cycle = 3 minutes, Acceleration =
19.6 m/s2, Direction = x,y, and z axes at 60 minutes per axis
Normal
operation
–
Leakage Current
Hold-Up Time
Nom
Nom
0.03 mA
0.10 mA
R = 1.5 kΩ,
C = 0.15 μF
–
Nom
–
–
74 ms at TA = 25°C
Table 2. Environment Tests
(At TA = 25° C)
Test Item
Conditions
Test Results
VIN
ILOAD
–
–
Power-On at High
Temperature
Nom
Max
Power-off for 1 hour at 65°C, then power-on
Normal
operation
–
Power-On at Low
Temperature
Nom
Max
Power-off for 1 hour at –15°C, then power-on
Normal
operation
–
–
–
Product is dropped from a height of 50 mm (98 m/s2 ) onto a flat surface of
wood (10 mm or thicker); the test is performed three times on each edge
of the bottom side of the product
Normal
operation
–
Specification
Remarks
Vibration
(Non-Operating)
Shock
Table 3. Noise Tolerance Characteristics
(At TA = 25° C)
Test Item
AC Line Noise
(50 to 1000 ns)
Lightning Surge
(1.2 × 50 μs)
Electrostatic Discharge
CHD40004-001A00-TD
Conditions
Test Results
VIN
ILOAD
Min to
Max
Min to
Max
Line to Line ±2.2 kV OK
L–L
2.0 kV
–
Min to
Max
Min to
Max
Line to Frame Ground ±2.2 kV OK
L–FG
2.0 kV
–
Nom
Min to
Max
Line to Line ±2.4 kV OK
L–L
2.0 kV
–
Nom
Min to
Max
Line to Frame Ground ±2.4 kV OK
L–FG
2.0 kV
Min to
Max
Min to
Max
±8.4 kV OK at R = 330 Ω, C = 150 pF
6.0 kV
SANKEN ELECTRIC CO., LTD.
–
8
March 8, 2013
C300
Table 4. Other Characteristics
(At TA = 25° C)
Test Item
Conditions
VIN
ILOAD
Test Results
P–S
P–E
S–E
Specification
P–S: 4.0 kV for 1 minute
P–E: 2.0 kV for 1 minute
2.4 kV for 1 second
S–E: 500 V for 1 minute
600 V for 1 second
Remarks
Withstand Voltage
–
–
4.0 kV
2.4 kV
0.6 kV
Leakage Current at
Withstand Voltage
–
–
2.29 mA
1.65 mA
1.71 mA
≤ 15 mA
–
Insulation Resistance
–
–
≥ 1000 MΩ
≥ 1000 MΩ
≥ 1000 MΩ
≥ 100 MΩ
at 500 VDC Megger
–
CHD40004-001A00-TD
SANKEN ELECTRIC CO., LTD.
–
9
March 8, 2013
C300
Important Information
!
• The products described in this document are built-in type DC stabilized power supplies with special structures and are designed for
installation in equipment. Be sure to use the products only for installation in equipment.
• The products should be handled only by persons who have competent electrical knowledge.
• Be sure to read through all safety precaution and operation manuals before installation, operation, or maintenance and to use the
products only for the intended use and in accordance with all applicable safety standards and regulations in the location of use.
Sanken reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit
improvements in the performance, reliability, or manufacturability of its products. Therefore, the user is cautioned to verify that the
information in this publication is current before placing any order.
When using the products described herein, the applicability and suitability of such products for the intended purpose shall be reviewed
at the users responsibility.
Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable.
Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or
systems against any possible injury, death, fires or damages to society due to device failure or malfunction.
Sanken products listed in this publication are designed and intended for use as components in general-purpose electronic equipment or
apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Their use in any application requiring radiation hardness assurance (e.g., aerospace equipment) is not supported.
When considering the use of Sanken products in applications where higher reliability is required (transportation equipment and its
control systems or equipment, fire- or burglar-alarm systems, various safety devices, etc.), contact a company sales representative to
discuss and obtain written confirmation of your specifications.
The use of Sanken products without the written consent of Sanken in applications where extremely high reliability is required (aerospace equipment, nuclear power-control stations, life-support systems, etc.) is strictly prohibited.
The information included herein is believed to be accurate and reliable. Application and operation examples described in this publication are given for reference only and Sanken assumes no responsibility for any infringement of industrial property rights, intellectual
property rights, or any other rights of Sanken or any third party that may result from its use. The contents in this document must not
be transcribed or copied without Sanken’s written consent.
CHD40004-001A00-TD
SANKEN ELECTRIC CO., LTD.
10
March 8, 2013