DVFX-100-TR (Ver. 1.0) www.opticis.com 1-Fiber Detachable DVI module, DVFX-100 DATA SHEET Contents Description Features Applications Technical Specifications Functions Drawing Fiber Connection DVI Pin Description OPTICIS HQ Opticis Co., Ltd. # 16Fl, Kins Tower Jeongja 331, 8 Sungnam-daero, Bundang-gu Sungnam-si, Gyunggi-do, 463-782 South Korea Te l: +82 (31) 719-8033 Fax: +82 (31) 719-8032 www.opticis.com [email protected] Copyright © 2013, All rights reserved by Opticis 15 Jan 2013 -1- DVFX-100-TR (Ver. 1.0) www.opticis.com 1-Fiber Detachable DVI module, DVFX-100 Description Optical graphic extension module consists of transmitter module and receiver module, each of which has one (1) SC connectors and a 24-pins DVI–D plug. Users could decide extension length at their discretion by choosing the length of fiber-optic cables with SC ferrules at the ends. It offers graphic TMDS signals to be extensible up to the limits of modal bandwidth of selected multi-mode glass fiber(50/125 um or 62.5/125um). The module has a capability to transmit WUXGA (1920x1200) graphic signals with 60Hz refresh rate using leading-edge OPTICIS fiber-optic component that transmits four (4) data channels over one multi-mode fiber. At such data bandwidth, this module can extend up to 1,640 feet (500 meters) much over the limits of copper wire extension, without any distribution amplifier or repeater. The EDID in a display can be read and restored by just plugging it to the display. This self-EDID programming feature makes the installation of DVFX-100 more easy and flexile at any variable resolution display systems. The modules are constituted of three parts as follows; - One (1) transmitter converting electrical to optical signals, model name: DVFX-100-T - One (1) receiver converting optical to electrical signals, model name: DVFX-100-R - Two (2) AC Adaptors to 110V-240V with DC 5V 1A outlet Features Extends all VESA resolution up to WUXGA (1920x1200) at 60Hz DVI data up to 500 meters (1640ft) over one (1) multi-mode fiber Detachable feature with a simplex SC connector for each module Offers self-EDID programming feature, detecting from a display and restoring to an EEPROM in the transmitter just by plugging to the display without any physical DDC connection The modules are compact enough to directly plug to graphic sources and displays by adopting DVIplugs Includes two (2) +5V DC power adapters for the transmitter and receiver Complies with Class 1 Laser Eye Safety in compliance with FDA/CDRH, UL/EN 60601-1, 60601-1-2 Certifies FCC and CE standards for EMI/RFI emission Data security with negligible RFI/EMI emissions and loss of video quality due to no copper conductor present Copyright © 2013, All rights reserved by Opticis 15 Jan 2013 -2- DVFX-100-TR (Ver. 1.0) www.opticis.com Applications Medical imaging system Video wall system Digital signage Military / Aerospace Broadcast Conference room / Education Technical Specifications - General Specifications Parameter Components Electrical Optical Mechanical Connect - Specifications Multi-mode VCSEL (Vertical Cavity Surface Emitting Laser) PIN-PD TMDS Level (complying with DVI1.0) Max. 2.25Gbps Max. 309 ps Max. 6ns Min 9.4dB 39 x 56 x 14.6mm Simplex SC connectors Laser Diodes in Tx Module Photo Diodes in Rx Module Input and Output Signals Data Transfer Rate (Graphic Data) Total Jitter at the end of Rx output Skew inter-channels Link Power Budget Module dimension (WDH) Optical Connector Electric Connector Type from Systems and to Displays Recommended Fiber 24 pin DVI-D plug 50/125 um Multi-mode Glass Fiber Absolute Maximum Ratings Parameter Supply Voltage Operating Temperature Storage Temperature Storage Relative Humidity Symbol VCC Top Ts Hs Minimum 0 - 30 10 Copyright © 2013, All rights reserved by Opticis Maximum + 7.0 50 + 70 95 Units V C C %RH 15 Jan 2013 -3- DVFX-100-TR (Ver. 1.0) www.opticis.com Operating Conditions Transmitter module (E-to-O converter): DVFX-100-TX - Power Supply TMDS Optical Link (Note3) Parameter Supply Voltage Supply Current Power Dissipation Power Supply Rejection (Note1) Data Output Load Graphic Supply Voltage (Note2) Single-Ended High Level Input Voltage Single-Ended Low Level Input Voltage Single-Ended Input Swing Voltage Output Optical Power Wavelength Spectral width in RMS Relative Intensity of Noise (Note4) Extinction Ratio Symbol Vcc ITCC PTX PSR Rising/Falling Time Jitter in p-p value (Note5) Trise/Tfall Tjitter Minimum 4.5 230 1.035 RLD GVCC Typical 5.0 240 1.20 Maximum 5.5 250 1.375 Units V mA W 50 mVp-p 50 Ω + 3.1 + 3.3 + 3.5 V GVIH GVCC 0.01 GVCC GVCC + 0.01 V GVIL GVCC - 0.6 - GVCC - 0.4 V GVISWING 0.4 - 0.6 V Po 850 1 990 3 dBm nm nm RIN -20 Ext dB/Hz 4 dB 260 260 ps ps Note1. Tested with a 50mVp-p sinusoidal signal in the frequency range from 500 Hz to 500 MHz on the V CC supply with the recommended power supply filter in place. Typically less than a 0.25 dB change in sensitivity is experienced. Note2. Graphic Supply Voltage is regulated reference voltage for signal processing in modules Note3. Measure signals at the end of 2 meter 50/125um MMGOF Note4. Measure in 1GHz of frequency bandwidth Note5. Use PPG (Pulse Pattern Generator) source with jitter 50ps Receiver module (O-to-E converter): DVFX-100-RX Power Supply TMDS Optical Link (Note9) Parameter Supply Voltage Supply Current Power Dissipation Power Supply Rejection (Note6) Data Input Load Graphic Supply Voltage (Note7) Single-Ended Output Swing Voltage (Note8) Receiving Optical Power Receiving Wavelength Signal_Detect Good Signal_Detect Fail Link Power Budget Total Jitter (note 10) Symbol Vcc IRCC PRX PSR Minimum 4.5 150 0.675 RLD GVCC Typical 5.0 160 0.8 Maximum 5.5 200 0.935 Units V mA W 50 mVp-p 50 Ω + 3.1 + 3.3 + 3.5 V GVISWING 0.2 - 0.4 V Po SDg SDf Pbgt TRjitter -11 850 1 990 -15 dBm nm dBm dBm dB ps -23 9.45 309 Note6. Tested with a 50mVp-p sinusoidal signal in the frequency range from 500 Hz to 500 MHz on the VCC supply with Copyright © 2013, All rights reserved by Opticis 15 Jan 2013 -4- DVFX-100-TR (Ver. 1.0) www.opticis.com the recommended power supply filter in place. Typically less than a 0.25 dB change in sensitivity is experienced. Note7. Graphic Supply Voltage is regulated reference voltage for signal processing in modules Note8. TMDS outputs are coupled in AC Note9. Measure signals at the end of 2 meter 50/125um MMGOF Note10. It is measured as total jitters including Tx and Rx modules under maximum extension, 500 meters with UXGA 60Hz. - Recommended Specifications of Fiber-Optic Cables Parameters Conditions Fiber Type Modal Bandwidth Fiber Cable Attenuation Extension Distance No. of Ferrules Skew Insertion Attenuation Total Optical Attenuation = 850nm = 850nm Simplex SC* In 330 ft (100 meter) extension Specifications 50m Multi-mode Graded Index Glass Fiber Min. 500 MHz km Max. 2.5dB/km 10 – 1650ft (500 meter) 1 ferrule Max. 0.4ns Max. 0.5dB Max. 1.5dB Note*: Some plastic couplers to clamp two LC connectors could not fit in. Functions - Self-EDID Function The EDID in a display can be read and restored by just plugging it to the display. This self-EDID programming feature makes the installation of DVFX-100 more easy and flexile at any variable resolution display systems. - Power Protection Circuit Mode in Transmitter Module The transmitter (Tx) module of DVFX-100-TR is designed for power protection circuit from conflict of power supply between the external AC/DC power adapter and your DVI source by #14 pin. We strongly recommend to use external AC/DC adapter for Transmitter (Tx) for stable power supplying. In case of Receiver (Rx), power should be supplied by AC/DC adapter due to no internal power supplying from the displays. - Signal Detect Mode in Receiver Module It offers optical signal monitoring LED when optical input power is lower than as specified in a certain case, for instance, loosing optical connectors. Copyright © 2013, All rights reserved by Opticis 15 Jan 2013 -5- DVFX-100-TR (Ver. 1.0) www.opticis.com Drawing Dimension [mm] Note: The transmitter, DVFX-100-T and the receiver, DVFX-100-R have the same mechanical dimensions. Fiber Connection The diagram shows the connection of transmitter (Tx; plug in PCs) and receiver (Rx; plug in displays) modules by using one (1) SC patch cords fiber. Up to 500m at WUXGA On e( 1) Op tica lF ibe r DVFX-100 Tx DVFX-100 Rx DVI Source Copyright © 2013, All rights reserved by Opticis DVI Display -6- 15 Jan 2013 DVFX-100-TR (Ver. 1.0) www.opticis.com DVI Pin Description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Symbol CH2CH2+ GND N.C. N.C. DDC Clock DDC Data N.C. CH1CH1+ GND N.C. N.C. 14 5V 15 GND Hot plug Detect CH0CH0+ GND N.C. N.C. GND CLK+ CLK- 16 17 18 19 20 21 22 23 24 Functional Description TMDS Data Signal Channel 2 Negative TMDS Data Signal Channel 2 Positive TMDS Data Signal Channel 2/4 Shield DDC Clock line for DDC2B communication DDC Data line for DDC2B communication TMDS Data Signal Channel 1 Negative TMDS Data Signal Channel 1 Positive TMDS Data Signal Channel 1/3 Shield Main Power Input for Transmitter from Host 5 V Output for Receiver to monitor Ground (Note11) Signal is driven by monitor to enable the system to identify the presence of a monitor TMDS Data Signal Channel 0 Negative TMDS Data Signal Channel 0 Positive TMDS Data Signal Channel 0/5 Shield TMDS Clock Signal Shield TMDS Clock Channel Positive TMDS Clock Channel Negative Note11) The AC-to-DC adapter for transmitter is option for Desk Top PC user. But Note PC user has to use the AC-to-DC adapter because the power of Note PC is not enough to drive DVFX-100 transmitter. Copyright © 2013, All rights reserved by Opticis 15 Jan 2013 -7-