M5-1003 (Ver. 1.1) www.opticis.com DATA SHEET Optical DVI/USB/RS232/Audio Extender M5-1003 Contents Description Features Absolute Maximum Ratings Recommended Operating Conditions Electrical Power Supply Characteristics Optical and Electrical Characteristics Drawing of transmitter and receiver modules DVI Pin Description/RS232 Pin Description Reliability Test of Modules Terminology Headquarters Opticis Co., Ltd # 304, Byucksan Technopia 434-6 Sangdaewon-Dong, Chungwon-Ku Sungnam City, Kyungki-Do, 462-120 South Korea Tel: +82 (31) 737-8033 Fax: +82 (31) 707-8079 Email: [email protected] www.opticis.com Copyright © 2012All rights reserved, Opticis Co., Ltd. -0- May. 2012 M5-1003 (Ver. 1.1) www.opticis.com Optical DVI/RS-232/USB/Audio Extender Description The reality of gigabit high-speed digital graphic interconnections mandates products that maintain front-of-screen video quality. Optical technology extends the ability to transmit digital graphic data beyond the physical limits of copper wires by, i) providing pure signal integrity over long distances for the optimum visual experience, ii) no EMI/RFI transmission or reception, iii) light weight, rugged cabling and connectors, iv) very cost effective per foot/metre, v) low power consumption, and vi) plug and go installation ease – no software requirements. M5-1003-TR offers integrated extension of digital video, audio and RS-232 interface up to 2km (6,600 ft) for DVI. The graphic resolution of this M5-1003 supports is WUXGA (1920x1200) at 60Hz refresh rate. The USB follows High-speed USB, version 2.0 (480Mbps). The audio supports stereo audio. RS232 serial interface offers device-to-device and device-to-controller connections to build up control system integration. It is designed to multiplex and de-multiplex the DVI video, stereo audio, Display Data Channel (DDC) command interface, serial protocol so as to be linked over 4 LC fibers. It gives benefits of all-glass fiber transmission medium, data security, and long distance extension up to 2km, easy plug-and-go installation and no RFI/EMI effects. In addition, a non-trivial feature is that both of Single and Multimode optical fibers are applicable. The EDID in a display can be read and restored by just plugging it to the display. This self-EDID programming feature makes the installation of M5-1003 more easy and flexile at any variable resolution display systems. The M5-1003-TR consists of an Uplink (or transmitter; Tx) and a Downlink (or receiver; Rx), connected by two duplex LC terminated single or multi-mode patch cords between them, which offers electrical perfect isolation. Each link module is driven by +12V/3A DC power adaptor. The shipping group is as follows; 1) One pair of the uplink and the downlink 2) Two +12V/3A power adaptors 3) User Manual Copyright © 2012All rights reserved, Opticis Co., Ltd. -1- May. 2012 M5-1003 (Ver. 1.1) www.opticis.com Feature Extends DVI, Audio and RS232 up to 1.5 km (optionally 2 km) using self DDC ready button on front panel. Video data: WUXGA (1920X1200), 24bit color and 60Hz refresh rate for DVI. Audio interface: 3.5mm diameter stereo jack. Serial control data: RS232 with 9-pin D-sub female connector in the transmitter and male connector in the receiver. Interconnection between transmitter and receiver: Two (2) Duplex LC patch cords of single or multi-mode fiber. Applicable of both single and multi-mode fiber. Offers DVI and USB ports for Local Display and Keyboard/Mouse. Lossless Image Quality with no Frame Dropping. +12 V DC power supply to each module. Offers self-EDID programming feature, detecting from a display and restoring to an EEPROM in the transmitter just by plugging to the display without any physical DDC connection. Offers optional remote console switch and indicators. No software to install; just plug and go. Data security with negligible RFI/EMI emissions Applications Keyboard, mouse and video extension and routing system related with servers or PCs control. Digital display system integration for medical, military, aerospace, factory automation, and traffic control platforms. Digital FPD, PDP and projector installation in conference rooms, auditoriums and for kiosk systems LED signboards for large scale information display and stadiums Copyright © 2012All rights reserved, Opticis Co., Ltd. -2- May. 2012 M5-1003 (Ver. 1.1) www.opticis.com Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage Transmitter Differential Input Voltage Relative Humidity Lead Soldering Temperature & Time Symbol Tstg VCC Vd RH - Minimum - 10 10 10 - Maximum + 85 16 1 95 Units C V V % 260C, 10 sec Recommended Operating Conditions Parameter Ambient Operating Temperature Data Output Load Power Supply Rejection (Note1) Supply Voltage Symbol TA RLD PSR VCC Minimum 0 Typical Maximum + 50 50 50 + 12.0 + 11.4 + 12.6 Units C Ω mVp-p V Note1. Tested with a 50mVp-p sinusoidal signal in the frequency range from 500 Hz to 500 MHz on the V CC supply with the recommended power supply filter in place. Typically less than a 0.25 dB change in sensitivity is experienced. Electrical Power Supply Characteristics (TA = 0 C to +50 C, unless otherwise noted) Parameter Supply Voltage Supply Current Power Dissipation TX RX TX RX Symbol VCC ITCC IRCC PTX PRX Minimum 11.4 720 660 8.0 7.5 Typical 12 750 690 9.0 8.3 Maximum 12.6 780 720 10.0 9.1 Units V mA mA W W DVI Electrical Characteristics TMDS Parameter Data Output Load Graphic Supply Voltage (Note2) Single-Ended High Level Input Voltage Single-Ended Low Level Input Voltage Single-Ended Input Swing Voltage TMDS Parameter Data Input Load Graphic Supply Voltage (Note2) Single-Ended Output Swing Voltage (Note3) Transmitter Symbol Minimum RLD Typical 50 Maximum Units Ω GVCC + 3.1 + 3.3 + 3.5 V GVIH GVCC 0.01 GVCC GVCC + 0.01 V GVIL GVCC - 0.6 - GVCC - 0.4 V 0.4 - 0.6 V Typical 50 Maximum Units Ω + 3.1 + 3.3 + 3.5 V 0.2 - 0.4 V GVISWING Receiver Symbol Minimum RLD GVCC GVISWING Note2. Graphic Supply Voltage is regulated reference voltage for signal processing in modules Note3. TMDS outputs are coupled in AC Copyright © 2012All rights reserved, Opticis Co., Ltd. -3- May. 2012 M5-1003 (Ver. 1.1) www.opticis.com Optical & Electrical Characteristics Parameters Symbol 1310 Tx 1550 Rx Data Bit Rate 1550 Tx 1310 Rx Fiber Length 9µum core SMF (Top = 25℃) Condition Unit PRBS 2 -1,NRZ 23 Mbps 23 Mbps PRBS 2 -1,NRZ Min. Typ. Max. Remark 1250 155.52 155.52 1250 -10 10 BER, 155Mbps/1.62Gbps km 2 dBm -11 -15 dB 4 CW, @ POUT nm 1270 1500 RMS Width TRANSMITTER Average Power Output POUT Extinction Ratio ER Center Wavelength C Spectral Width -9 -10 -7 -8 1310 1550 nm 1355 1600 4.0 dB/Hz -120 nsec 0.26 2.0 If=IBIAS + Imod/2 RIN Optical Rise/Fall Time tr/tf 20 – 80% Sensitivity (Average Input Power) 1310 Wavelength 1550 Receiver Overload Signal Detect Threshold Decreasing light input Increasing light input PIN,MIN PRBS 2 -1, -10 10 BER @1.31 µm @1.55 µm RECEIVER Signal Detect Hysteresis 23 dBm nm PIN,MAX dBm PD PA dBm dBm PA - PD dB 1260 1500 -3.0 1310 1550 -23 -19 1360 1600 155M Rx 1.25G Rx PIN,MIN-3 PIN,MIN-2 0.5 Audio (Analog) Analog Sample Rate Faudio_a kHz 48 Input level Output level Input Impedance Output Impedance Ain Aout Vpp Vpp kΩ Ω 0.56Vss 0.65 25 100 Vpp=3.3V/Analog RS232 Electrical Characteristics Parameter Data rate Input voltage Output voltage Symbol Minimum Rin Tout -25 Typical ±15 Copyright © 2012All rights reserved, Opticis Co., Ltd. -4- Maximum 250 25 Units kbps V V May. 2012 M5-1003 (Ver. 1.1) www.opticis.com Drawing of transmitter and receiver modules Dimension [mm] Transmitter Receiver Copyright © 2012All rights reserved, Opticis Co., Ltd. -5- May. 2012 M5-1003 (Ver. 1.1) www.opticis.com DVI Pin Description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Symbol CH2CH2+ GND Functional Description TMDS Data Signal Channel 2 Negative TMDS Data Signal Channel 2 Positive TMDS Data Signal Channel 2 Shield DDC Clock DDC Data N.C. CH1CH1+ GND DDC Clock line for DDC2B communication DDC Data line for DDC2B communication 14 5V 15 GND Hot plug Detect CH0CH0+ GND 5 V Input for Transmitter from Host 5 V Output for Monitor from Receiver Ground Signal is driven by monitor to enable the system to identify the presence of a monitor TMDS Data Signal Channel 0 Negative TMDS Data Signal Channel 0 Positive TMDS Data Signal Channel 0 Shield GND CLK+ CLK- TMDS Clock Signal Shield TMDS Clock Channel Positive TMDS Clock Channel Negative 16 17 18 19 20 21 22 23 24 TMDS Data Signal Channel 1 Negative TMDS Data Signal Channel 1 Positive TMDS Data Signal Channel 1 Shield Note: Channels 3, 4 and 5 dual-link data signal pins are not used RS232C Pin Description Pin 1 2 3 4 5 6 7 8 9 Symbol Received Line Signal Detector RD TD Data Terminal Ready GND Data Set Ready Request To Send Clear To Send NC Functional Description Connected with Pin4 & Pin6 in module Data Receive: Uplink Downlink Data Transmit: Uplink Downlink Connected with Pin1 & Pin6 in module Signal Ground Connected with Pin1 & Pin4 in module Connected with Pin8 in module Connected with Pin7 in module Connection tips: 1) Connection of PC-to-PC: Cross connection of pins 2 and 3 between two PCs. 2) Connection of PC-to-Device: Straight connection of pin 2:2 and pin 3:3 Copyright © 2012All rights reserved, Opticis Co., Ltd. -6- May. 2012 M5-1003 (Ver. 1.1) www.opticis.com Reliability Test Opticis utilizes three types of test criteria for a reduction of variability and a continuous improvement of the process by its FEMA (Failure Mode and Effective Analysis) program. 1) Mechanical test (vibration, shock) 2) Temperature & humidity tests 3) EMC test (FCC class A and CE Verification) Mechanical and Temperature & Humidity Test Data Heading Operating Test Storage Test Test Operating at each Temperature (See Note) Duration Sample Failure Size 30 Min * 0 ~ 50 °C (Each (Interval: 10 °C) n =3 0 Temperature) Remarks Note: Visual Test on the Display Low Temperature * TS = -30 °C 96 HR n=3 0 1. TS: Storage Temperature High Temperature * TS = 70 °C 96 HR n=3 0 2. RH: Relative Humidity High Humidity * TS: 60 °C 96 HR n=3 0 High Temperature * RH: 90% - n=2 0 - n=2 0 Mechanical Shock Mechanical Test Conditions * Pulse: 11 ms * Peak level: 30 g * Shock pulse: 3 times/Axis * Peak acceleration: 20 g Mechanical * Frequency: 20~2000 ㎐ Vibration * Sweep time: 30 Minutes * 4 Times/Axis Copyright © 2012All rights reserved, Opticis Co., Ltd. -7- May. 2012 M5-1003 (Ver. 1.1) www.opticis.com EMC Test Data 1) EMI: Meet FCC class A (ICES-003) and CE class A STANDARDS EN 55 022 (CISPR22) CE (Conducted Emission) & FCC; PART 15 SUBPART B RE (Radiated Emission) EN 61000-3-2 (IEC 61000-3-2) Harmonics EN 61000-3-3 (IEC 61000-3-3) Flickers CONDITIONS Meet Class A Meet Class A Meet Class A 2) EMS: Meet CE standards (EN 55024) and CISPR24 equivalents EN 61 000-4-2:1995 EN 61 000-4-3:1996 EN 61 000-4-4:1995 EN 61 000-4-5:1995 EN 61 000-4-6:1996 EN 61 000-4-11:1994 STANDARDS Electrostatic Discharge Immunity (Air: 8kv, Contact: 4kv) Radiated RF E-Field (80~1000 MHz) 3V/m (AM 80%, 1kHz) Fast Transients (5kHz, 60Seconds) Surge Transients Conducted Susceptibility (CS) Radiated Susceptibility (RS) Voltage Dips, Interruption & Variation Copyright © 2012All rights reserved, Opticis Co., Ltd. -8- CONDITIONS Meet Criterion A Meet Criterion A Meet Criterion A Meet Criterion A Meet Criterion A Meet Criterion A and C May. 2012