M1-2R2H-TR (Ver. 1.5) www.opticis.com DATA SHEET Optical HDMI Extension Module M1-2R2H-TR Contents Description Features Applications Technical Specifications Functions Drawing of Modules Drawing of Cable Connections HDMI Pin Description Pin Description of DDC Connector Reliability Test Headquarter Opticis Co., Ltd. # 501, ByucksanTechnopia, 434-6 Sangdaewon-Dong, Chungwon-Ku Sungnam City, Kyungki-Do, 463-120 South Korea Tel: +82 (31) 737-8033~9 Fax: +82 (31) 737-8079 www.opticis.com Copyright © 2007, All rights reserved by Opticis -1- 25, November , 2011 M1-2R2H-TR (Ver. 1.5) www.opticis.com Optical HDMI Extension Module - HDMI Fiber Detachable Connection System Description The M1-2R2H-TR HDMI (High Definition Multimedia Interface) extension module is a new member of the Opticis family of products that stretches your HDMI connectivity, offering a benefit of detachability of connection with a four (4) LC fiber cable and a UTP (Untwisted Pair) cable, which makes it easier to install. The reality of high-speed digital graphic interconnections mandates products to maintain video quality and cost effectiveness of integrated display systems. Optical technology for gigabit digital transmission makes it simple to extend digital graphic data above the extension limits of copper wires providing pure signal integrity for an ideal visual experience, no EMI/RFI emissions, light weight, rugged cabling and connectors, low power consumption and installation ease. The extension system consists of transmitter and receiver module boxes with female HDMI receptacles, being able to connect Set-top boxes or DVDP’s and digital HD-TV’s by short HDMI copper cables respectively. A LC patch cords fiber-optic cable enables to transmit HD-TV data (1080p) and a UTP cable with RJ-45C enables to manage power and EDID/HDCP parameters up to 100m (330ft). Internally, Opticis’ optical technology - the transmitter’s 850nm VCSEL array and the receiver’s Pin-PD array, are concealed within the connector housings. The UTP cable with RJ-45C connectors for DDC, which is popular as LAN cables, is so designed as to utilize easily. The product is certified to EMI Class B by for FCC or CE for home uses as well as industrial or commercial uses. If you want to extend only HD-TV data neglecting HDCP, the product allows you to connect only a two-duplex LC patch cord fibre cable without a UTP cable and offers longer extension up to 500m (1,650feet). The shipping group is shown as follows; 1) One transmitter converting electrical to optical signals, model name: M1-2R2H-T 2) One receiver converting optical to electrical signals, model name: M1-2R2H-R 3) HDMI copper cables: 2 X M1-HVCO-010 (1.0m) Copyright © 2007, All rights reserved by Opticis -2- 25, November , 2011 M1-2R2H-TR (Ver. 1.5) www.opticis.com 4) AC/DC +12V power adapter: M1-2D12PW 5) Copper cable for DDC (Option): M1-DDCRJ-xxx (RJ45-C Connector), where xxx stands for the cable length in meter up to 100m (330 feet). The standard length is 20 meter (66feet). 6) Fiber-optic Break-out cable with 4xLC connectors (Option), being strongly recommended for use in harsh environments: LDP-625BO-xxx, where xxx stands for the cable length up to 500m (1,650 feet). Features Comply with HDMI 1.2 standard for HD-TV and HDCP communication. Extend digital HDTV data with HDCP upto 100m (330 feet). Be certified in Class B, the home standard by FCC or CE. Support up to HDTV 1080p (1,920x1,080) as well as WUXGA (1,920x1,200) resolution at 60Hz refresh rate with 1 pixel/clock mode. Adopt a +12V external power supply to supply both modules over DDC cable. Not require S/W driver to install; just plug and play. Use 850nm multimode light sources and equivalent photo detectors, so recommend 2 duplex LC patch-cord multimode GOF buffered cables or 4xLC breakout GOF cable. Adopt 2 Duplex LC receptacles on the side-face of modules. Comply with FDA/CDRH and IEC 60825-1 Class 1 Laser Eye Safety. Applications Digital HD-TV of types of LCD, PDP, projection and projectors for Home or Commercial Entertainments Digital HD-TVs for industrial applications such as medical appliances, aero traffic control, factory, conference room, auditorium and bank Digital FPDs and projectors in conference room and auditorium Kiosk with digital FPDs showing full motion graphic displays from remote systems HD-TVs for information display in public sites LED signboards in streets or in stadiums Copyright © 2007, All rights reserved by Opticis -3- 25, November , 2011 M1-2R2H-TR (Ver. 1.5) www.opticis.com Technical Specifications General Specifications - Parameter Components Electrical Optical Connect Specifications 850nm Multi-mode VCSEL (Vertical Cavity Surface Emitting Laser) GaAs PIN-PD TMDS Level (complying with DVI1.0) Max. 1.62Gbps Max. 309 ps Max. 6ns Min 10.5dB 2 Duplex LC connectors Laser Diodes in Tx Module Photo Diodes in Rx Module Input and Output Signals Data Transfer Rate (Graphic Data) Total Jitter at the end of Rx output Skew inter-channels Link Power Budget Optical Connector Electric Connector Type from Modules and to HDTVs DDC Electric Cables between Two Modules Recommended Fiber HDMI receptacle RJ45-C 62.5/125 or 50/125 um Multi-mode Glass Fiber Absolute Maximum Ratings - Parameter Supply Adaptor Voltage Operating Temperature Operating Relative Humidity Storage Temperature Storage Relative Humidity Symbol VCC Top RHop Tsto RHsto Minimum + 10.0 -10 5 - 30 5 Maximum +16.0 50 80* + 60 95* Units V C %RH C %RH Note*: Under the condition of No drops of dew Operating Conditions - Transmitter module : M1-2R2H-T Power Supply TMDS Optical Link (Note3) Parameter Supply Adaptor Voltage Supply Voltage Supply Current Power Dissipation Power Supply Rejection (Note1) Data Output Load Graphic Supply Voltage (Note2) Single-Ended High Level Input Voltage Single-Ended Low Level Input Voltage Single-Ended Input Swing Voltage Output Optical Power Wavelength Spectral width in RMS Relative Intensity of Noise (Note4) Extinction Ratio Rising/Falling Time Jitter in p-p value (Note5) Symbol AVcc Vcc ITCC PTX Minimum 11.4 4.5 - Typical 12 5 200 1.0 Maximum 12.6 5.5 250 1.375 Units V V mA W PSR 50 mVp-p RLD 50 Ω GVCC + 3.1 + 3.3 + 3.5 V GVIH GVCC - 0.01 GVCC GVCC + 0.01 V GVIL GVCC - 0.6 - GVCC - 0.4 V GVISWING 0.2 - 0.8 V Po -9.5 830 850 -3.6 860 0.85 dBm nm nm RIN -117 Ext Trise/Tfall Tjitter dB/Hz 9 260 290 dB ps ps Note1. Tested with a 50mVp-p sinusoidal signal in the frequency range from 500 Hz to 500 MHz on the V CC supply with the recommended power supply filter in place. Typically less than a 0.25 dB change in sensitivity is experienced. Copyright © 2007, All rights reserved by Opticis -4- 25, November , 2011 M1-2R2H-TR (Ver. 1.5) www.opticis.com Note2. Note3. Note4. Note5. Graphic Supply Voltage is regulated reference voltage for signal processing in modules Measure signals at the end of 2 meter 50/125um MMGOF Measure in 1GHz of frequency bandwidth Use PPG (Pulse Pattern Generator) source with jitter 50ps Receiver module: M1-2R2H-R Power Supply TMDS Optical Link (Note9) Parameter Supply Adaptor Voltage Supply Voltage Supply Current Power Dissipation Power Supply Rejection (Note6) Data Input Load Graphic Supply Voltage (Note7) Single-Ended Output Swing Voltage (Note8) Receiving Optical Power Receiving Wavelength Signal_Detect Good Signal_Detect Fail Symbol AVcc Vcc IRCC PRX Minimum 11.4 4.5 - Typical 12 5 300 1.5 Maximum 12.6 5.5 350 1.925 Units V V mA W PSR 50 mVp-p RLD 50 Ω GVCC + 3.1 + 3.3 + 3.5 V GVISWING 0.4 - 0.8 V Po SDg SDf -20 830 850 -3.6 860 -17 -25 dBm nm dBm dBm Link Power Budget Pbgt 10.5 dB Total Jitter (note 10) TRjitter 309 ps Note6. Tested with a 50mVp-p sinusoidal signal in the frequency range from 500 Hz to 500 MHz on the V CC supply with the recommended power supply filter in place. Typically less than a 0.25 dB change in sensitivity is experienced. Note7. Graphic Supply Voltage is regulated reference voltage for signal processing in modules Note8. TMDS outputs are coupled in AC Note9. Measure signals at the end of 2 meter 50/125um MMGOF Note10. It is measured as total jitters including Tx and Rx modules under maximum extension, 500 meters with UXGA 60Hz. - Recommended Specifications of Fiber-Optic Cables Parameters Fiber Type Modal Bandwidth Fiber Cable Attenuation No. of Ferrules Skew Insertion Attenuation Total Optical Attenuation Conditions Multimode Glass of Fiber = 850nm = 850nm A pair of duplex LC* or 4 simplex LCs In 330 ft (100 meter) extension Specifications 62.5/125 or 50/125m Min. 400 MHz km Max. 3.5dB/km 4 ferrules Max. 0.4ns Max. 0.5dB Max. 1.5dB Note*: some plastic couplers to clamp two LC connectors could not fit in. Copyright © 2007, All rights reserved by Opticis -5- 25, November , 2011 M1-2R2H-TR (Ver. 1.5) www.opticis.com Functions - Power Save Mode in Transmitter Module The laser diodes work only when +5V voltage should be supplied into the 14-pin in DVI connectors, that is, detecting plugging the DVI plug to the PC. The voltage passing through a regulator from the +5V PC power or external power has LD drive circuit work. - Signal Detect Mode in Receiver Module It offers squelch function blocking output signals when optical input power is lower than as specified in a certain case, that is, detecting loosing the LC fiber-optic patch cord. Drawing of Modules Dimension [mm] RJ-45C Receptacle Note: The transmitter, M1-2R2H-T and the receiver, M1-2R2H-R have the same mechanical dimensions. Copyright © 2007, All rights reserved by Opticis -6- 25, November , 2011 M1-2R2H-TR (Ver. 1.5) www.opticis.com Drawing of Cable Connections RJ-45C UTP Cable Copyright © 2007, All rights reserved by Opticis -7- 25, November , 2011 M1-2R2H-TR (Ver. 1.5) www.opticis.com HDMI Pin Description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Symbol CH2+ GND Ch2CH1+ GND CH1CH0+ GND CH0CLK+ GND CLKCEC Reserved SCL SDA GND 18 5V 19 Hot plug Detect Functional Description TMDS Data Signal Channel 2 Positive TMDS Data Signal Channel 2 Shield TMDS Data Signal Channel 2 Negative TMDS Data Signal Channel 1 Positive TMDS Data Signal Channel 1 Shield TMDS Data Signal Channel 1 Negative TMDS Data Signal Channel 0 Positive TMDS Data Signal Channel 0 Shield TMDS Data Signal Channel 0 Negative TMDS Clock Channel Positive TMDS Clock Signal Shield TMDS Clock Channel Negative Consumer Electronics Control Not used HDCP/DDC communication clock HDCP/DDC communication data DDC/CEC shield 5 V Input for Transmitter from Host 5 V Output for Monitor from Receiver Signal is driven by monitor to enable the system to identify the presence of a monitor Pin Description for DDC Connector 1 2 3 4 5 6 7 8 Pin 1 2 3 4 5 6 7 8 Symbol DDC Data GND DDC Data DDC Clock GND Power GND Power DDC Clock 5V_IN HPD Copyright © 2007, All rights reserved by Opticis -8- Functional Description DDC Data line return ground DDC Data line for DDC2B communication DDC Clock line return ground Main power return ground Main power for Opticis module DDC Clock line for DDC2B communication DVI 5V (DVI No. 14 pin for Monitor) Signal is driven by monitor to enable the system to identify the presence of a monitor 25, November , 2011 M1-2R2H-TR (Ver. 1.5) www.opticis.com Reliability Test We have three kinds of test criteria for a reduction of variability and a continuous improvement of the process by our FMEA (Failure Mode and Effective Analysis) program. 1) Mechanical test (Vibration, Shock) 2) Temp. & Humidity test 3) EMC test (FCC class A and CE Verification for M1-2R2-TR; FCC class B and CE Certification for M1-2S2-TR) Mechanical and Temp. & Humidity Test Duration Sample Size 30 Min (Each Temperature) n=3 TS = -30℃ 96 HR n=3 High Temperature TS = 60℃ 96 HR n=3 High Humidity / High Temperature TS: 60℃ RH: 85% 96 HR n=3 Mechanical Shock Pulse: 11 ms Peak level: 30 g Shock pulse: 6times/Axis - n=3 Heading Test Operating Test Operating at each Temperature (See Note) -10~50℃ (Interval: 10℃) Low Temperature Storage Test Mechanical Test Mechanical Vibration Conditions Peak acceleration: 5 g Frequency: 10~55 ㎐ Sweep time: 5 Minutes 2 Times/Axis Copyright © 2007, All rights reserved by Opticis -9- - Remarks Note: Evaluate display quality of Laser Beam Projector connected to Graphic Signal Generator (Quantum Data: GD-802B) at each temperature. 1. TS: Storage Temperature 2. RH: Relative Humidity n=3 25, November , 2011 M1-2R2H-TR (Ver. 1.5) www.opticis.com EMC Test 1) EMI: Meet FCC class A or B (ICES-003) and CE class A or B STANDARDS EN 55 022 (CISPR22) CE (Conducted Emission) & FCC; PART 15 SUBPART B RE (Radiated Emission) EN 61000-3-2 (IEC 61000-3-2) Harmonics EN 61000-3-3 (IEC 61000-3-3) Flickers CONDITIONS Meet Class A or B Meet Class A or B Meet Class A or B 2) EMS: Meet CE standards (EN 55024) and CISPR24 equivalents EN 61 000-4-2:1995 EN 61 000-4-3:1996 EN 61 000-4-4:1995 EN 61 000-4-5:1995 EN 61 000-4-6:1996 EN 61 000-4-11:1994 STANDARDS Electrostatic Discharge Immunity (Air: 8kv, Contact: 4kv) Radiated RF E-Field (80~1000 MHz) 3V/m (AM 80%, 1kHz) Fast Transients (5kHz, 60Seconds) Surge Transients Conducted Susceptibility (CS) Radiated Susceptibility (RS) Voltage Dips, Interruption & Variation Copyright © 2007, All rights reserved by Opticis - 10 - CONDITIONS Meet Criterion A or B Meet Criterion A or B Meet Criterion A or B Meet Criterion A or B Meet Criterion A or B Meet Criterion A or B, and C 25, November , 2011 M1-2R2H-TR (Ver. 1.5) www.opticis.com Terminology HDMI HDCP DDC EDID EMI RFI EMS PDP TFT-LCD TMDS VCSEL VESA High Definition Multimedia Interface. Digital connection only – no analog. High-bandwidth Digital Content Protection. These parameters are part of the 2002 High Definition Multimedia Interface (HDMI) specification for Consumer Electronics. Digital Display Channel. Latest specification is DDC2B. Extended Display Identification Data. EDID parameters are sent over the DDC link. Electro Magnetic Interference. Radio Frequency Interference. Electro Magnetic Susceptibility. Plasma Display Panel. Large HDTV panels up to 63” use this display technology. Thin Film Transistor Liquid Crystal Display – the technology of most computer display panels with VESA resolutions up to 1600x1200 pixels. Transmission Minimized Differential Signalling is the Silicon Image Inc. protocol for the digital signals. Vertical Cavity Surface Emitting Laser transmitter diode. The receiver diode is the PIN-Photo Diode. These components are designed and manufactured by Opticis. Video Electronics Standards Association. Revised on August 16, 2006; adding supporting resolution for HDTV at page 2 Updated only for HDMI model, M1-2R2H-TR on 12 April 2007 Copyright © 2007, All rights reserved by Opticis - 11 - 25, November , 2011