M1-2000 (Ver. 1.1) www.opticis.com DATA SHEET HDMI - HDCP Extension Cable M1-2000 Contents Description Features Absolute Maximum Ratings Recommended Operating Conditions Electrical Power Supply Characteristics Receiver Electrical Interface Specifications of fiber-optic cables Drawing of transmitter and receiver modules DVI Pin Description Reliability Test of Modules Terminology Headquarter Opticis Co., Ltd. # 501, ByusanTechnopia, 434-6 Sangdaewon-Dong, Chungwon-Ku, Sungnam City, Kyungki-Do, 463-120 South Korea Tel: +82 (31) 737-8033~9 Fax: +82 (31) 707-8079 www.opticis.com Copyright © 2011, All rights reserved, Opticis Co., Ltd. JUL. 2011 M1-2000 (Ver. 1.1) www.opticis.com Optical HDMI - HDCP Extension Cable * Point-to-point optical fibre cable * Description The M1-2000 HDMI extension cable is a new member of the Opticis family of products that stretches your High-Definition Multimedia Interface connectivity. The M1-2000 is a hybrid cable solution using multi-mode glass fibers for the Red, Green, Blue and Clock high-speed digital graphic signals and copper wires for the low frequency HDCP control signals, wrapped in a PVC jacket. The reality of gigabit high-speed digital graphic interconnections mandates products that maintain front-of-screen video quality. Optical technology extends the ability to transmit hi-definition multimedia data beyond the physical limits of copper wires by, i) providing pure signal integrity over long distances for the optimum visual experience, ii) no EMI/RFI transmission or reception, iii) light weight, rugged cabling and connectors, iv) very cost effective per foot/metre, v) low power consumption, and vi) plug and go installation ease – no software requirements. The product consists of a transmitter and a receiver, which are connected by bundled optical fibre and copper cables. There are male HDMI connectors at each end. The high-speed graphic data transmission is accomplished by using a VCSEL array inside the transmitter connector, and a Pin-PD array inside the receiver connector. The shipping group is as follows; 1) One HDMI cable: M1-2000-xxx, where x = length in metres. 2) Factory will stock “standard” lengths of 10m, 20m, 30m, 50m, 70m and 100m. 3) User’s Manual Copyright © 2011, All rights reserved, Opticis Co., Ltd. -1- JUL. 2011 M1-2000 (Ver. 1.1) www.opticis.com Feature Checklist Extend HDMI signals up to 100m (330ft) with no signal degradation. Supports up to 1080p resolution. Complies with HDMI standard supporting HDCP parameters. Complies with DVI standard (165Mpixels/sec maximum) and supports DDC2B mode. Uses the host +5V source from the HDMI connector pin number 18 to drive the Tx and Rx modules, assuming a minimum of 500mA is available from the host If your HDTV source is unable to provide a minimum of +5V, 500mA on pin 18, just plug the external AC/DC power supply in Tx module for operation. Data security inherent with fibre & no RFI/EMI emissions. No software required; just plug and go. User Manual is available in non-supplier specific format for “white box” sales. Applications Home Theatre applications. Digital TFT-LCD FPDs, PDPs and projectors for medical imaging, air traffic control, factory automation, conference rooms, auditorium A/V systems, etc. Kiosks with digital FPDs showing full motion graphic displays from remote systems PDP displays for information display in public sites. LED signboards in streets and stadiums. Options Custom lengths up to 100m are also available from the factory. Copyright © 2011, All rights reserved, Opticis Co., Ltd. -2- JUL. 2011 M1-2000 (Ver. 1.1) www.opticis.com Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage Transmitter Differential Input Voltage Relative Humidity Lead Soldering Temperature & Time Symbol Tstg VCC Vd RH - Minimum - 30 - 0.3 0 - Maximum + 70 + 6.0 1 85 Units C V V % 260C, 10 sec Recommended Operating Conditions Parameter Ambient Operating Temperature Data Output Load Power Supply Rejection (Note1) Supply Voltage Graphic Supply Voltage (Note2) Symbol TA RLD PSR VCC GVCC Minimum 0 + 4.5 + 3.0 Typical Maximum + 50 50 50 + 5.0 + 3.3 + 5.5 + 3.6 Units C Ω mVp-p V V Note1. Tested with a 50mVp-p sinusoidal signal in the frequency range from 500 Hz to 500 MHz on the V CC supply with the recommended power supply filter in place. Typically less than a 0.25 dB change in sensitivity is experienced. Note2. Graphic Supply Voltage is only for the Graphic Signal Interface which is generated by regulator in the Transmitter and Receiver Electrical Power Supply Characteristics Parameter Supply Voltage Supply Current Power Dissipation TX RX TX RX Symbol VCC ITCC IRCC PTX PRX Minimum 4.5 - Typical 5 170 130 0.85 0.65 Maximum 5.5 200 150 1.1 0.825 Units V mA mA W W Specifications of Fibre-Optic Cables Parameter Core Diameter Buffer Diameter Outside Diameter Proof Test Level Value 62.5um (MMGOF) 0.25mm (MMGOF) 7.2mm 0.53GPa Copyright © 2011, All rights reserved, Opticis Co., Ltd. -3- JUL. 2011 M1-2000 (Ver. 1.1) www.opticis.com Drawing of transmitter and receiver modules Dimension [mm] HDMI Pin Description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Symbol CH2+ GND Ch2CH1+ GND CH1CH0+ GND CH0CLK+ GND CLKCEC Reserved SCL SDA GND 18 5V 19 Hot plug Detect Functional Description TMDS Data Signal Channel 2 Positive TMDS Data Signal Channel 2 Shield TMDS Data Signal Channel 2 Negative TMDS Data Signal Channel 1 Positive TMDS Data Signal Channel 1 Shield TMDS Data Signal Channel 1 Negative TMDS Data Signal Channel 0 Positive TMDS Data Signal Channel 0 Shield TMDS Data Signal Channel 0 Negative TMDS Clock Channel Positive TMDS Clock Signal Shield TMDS Clock Channel Negative Not used DDC/CEC shield 5 V Input for Transmitter from Host 5 V Output for Monitor from Receiver Signal is driven by monitor to enable the system to identify the presence of a monitor Copyright © 2011, All rights reserved, Opticis Co., Ltd. -4- JUL. 2011 M1-2000 (Ver. 1.1) www.opticis.com Reliability Test Opticis utilizes three types of test criteria for a reduction of variability and a continuous improvement of the process by its FEMA (Failure Mode and Effective Analysis) program. 1) Mechanical test (vibration, shock) 2) Temperature & humidity tests 3) EMC test (FCC class A and CE Verification) Mechanical and Temperature & Humidity Test Data Heading Operating Test Storage Test Test Operating at each Temperature Conditions Duration Sample Failure Size 30 Min * - 0 ~ 50 °C (Each (Interval: 10 °C) n =4 0 Temperature) (See Note) Remarks Note: Visual Test the Display Low Temperature * TS = -30 °C 96 HR n=2 0 1. TS: Storage Temperature High Temperature * TS = 70 °C 96 HR n=2 0 2. RH: Relative Humidity High Humidity * TS: 85 °C High Temperature 96 HR n=2 0 * RH: 85% - n=2 0 - n=2 0 Mechanical Shock * Pulse: 11 ms * Peak level: 30 g * Shock pulse: 3 times/Axis Mechanical Test * Peak acceleration: 20 g Mechanical * Frequency: 20~2000 ㎐ Vibration * Sweep time: 30 Minutes * 4 Times/Axis Copyright © 2011, All rights reserved, Opticis Co., Ltd. -5- JUL. 2011 on M1-2000 (Ver. 1.1) www.opticis.com EMC Test Data 1) EMI: Meet FCC class A (ICES-003) and CE class A STANDARDS EN 55 022 (CISPR22) CE (Conducted Emission) & FCC; PART 15 SUBPART B RE (Radiated Emission) EN 61000-3-2 (IEC 61000-3-2) Harmonics EN 61000-3-3 (IEC 61000-3-3) Flickers CONDITIONS Meet Class A Meet Class A Meet Class A 2) EMS: Meet CE standards (EN 55024) and CISPR24 equivalents EN 61 000-4-2:1995 EN 61 000-4-3:1996 EN 61 000-4-4:1995 EN 61 000-4-5:1995 EN 61 000-4-6:1996 EN 61 000-4-11:1994 STANDARDS Electrostatic Discharge Immunity (Air: 8kv, Contact: 4kv) Radiated RF E-Field (80~1000 MHz) 3V/m (AM 80%, 1kHz) Fast Transients (5kHz, 60Seconds) Surge Transients Conducted Susceptibility (CS) Radiated Susceptibility (RS) Voltage Dips, Interruption & Variation CONDITIONS Meet Criterion B Meet Criterion A Meet Criterion B Meet Criterion B Meet Criterion A Meet Criterion C Terminology DDC DVI-D EDID EMI EMS HDCP PDP RFI TFT-LCD TMDS VCSEL VESA Digital Display Channel. Latest specification is DDC2B. Digital Visual Interface. Digital connection only – no analog. Extended Display Identification Data. EDID parameters are sent over the DDC link. Electro Magnetic Interference. Electro Magnetic Susceptibility. High Definition Content Protection. These parameters are part of the 2002 High Definition Multimedia Interface (HDMI) specification for Consumer Electronics. Plasma Display Panel. Large HDTV panels up to 63” use this display technology. Radio Frequency Interference. Thin Film Transistor Liquid Crystal Display – the technology of most computer display panels with VESA resolutions up to 1600x1200 pixels. Transmission Minimized Differential Signalling is the Silicon Image Inc. protocol for the digital signals. Vertical Cavity Surface Emitting Laser transmitter diode. The receiver diode is the PIN-Photo Diode. These components are designed and manufactured by Opticis. Video Electronics Standards Association. Copyright © 2011, All rights reserved, Opticis Co., Ltd. -6- JUL. 2011