28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G About this document Scope and purpose This document is an engineering report that describes universal input 28 W 12 V off-line flyback converter using Infineon Quasi-Resonant CoolSET™ ICE2QR1080G which offers high efficiency, very low standby power, wider VVCC operating range and various mode of protections for a high reliable system. This demonstrator board is designed for users who wish to evaluate the performance of ICE2QR1080G in ease of use. Intended audience This document is intended for power supply design/application engineer, students, etc.) who wish to design low cost and high reliable systems of off-line Switched Mode Power Supply (SMPS) for enclosed adapter, bluray/DVD player, set-top box, game console, smart meter, auxiliary power supply of white goods, PC, server, etc. Table of Contents About this document ....................................................................................................................... 1 Table of Contents ........................................................................................................................... 1 1 Abstract ........................................................................................................................ 3 2 Demonstrator board ...................................................................................................... 4 3 Specifications of Demonstrator Board.............................................................................. 5 4 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 Circuit description ......................................................................................................... 6 Line input ....................................................................................................................................................... 6 Start up ........................................................................................................................................................... 6 Integrated MOSFET and PWM control ......................................................................................................... 6 RCD clamper circuit ....................................................................................................................................... 6 Output stage .................................................................................................................................................. 6 Feedback loop ............................................................................................................................................... 6 Primary side peak current control ............................................................................................................... 7 Digital frequency reduction.......................................................................................................................... 7 Active burst mode ......................................................................................................................................... 7 5 5.1 5.2 5.3 5.4 5.5 Protection features ........................................................................................................ 8 VVCC over voltage and under voltage protection ......................................................................................... 8 Over load/Open loop protection ................................................................................................................. 8 Over temperature protection....................................................................................................................... 8 Adjustable output overvoltage protection ................................................................................................. 8 Short winding protection ............................................................................................................................. 8 6 Circuit diagram.............................................................................................................. 9 7 7.1 7.2 PCB layout ...................................................................................................................11 Top side ........................................................................................................................................................ 11 Bottom side .................................................................................................................................................. 11 8 Bill of material..............................................................................................................12 9 Transformer construction ..............................................................................................13 Application Note www.infineon.com Please read the Important Notice and Warnings at the end of this document Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Abstract 10 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 Test results ..................................................................................................................14 Efficiency, regulation and output ripple ................................................................................................... 14 Standby power............................................................................................................................................. 16 Line regulation ............................................................................................................................................. 16 Load regulation ........................................................................................................................................... 17 Maximum input power ................................................................................................................................ 17 ESD immunity (EN61000-4-2) ..................................................................................................................... 17 Surge immunity (EN61000-4-5) .................................................................................................................. 17 Conducted emissions (EN55022 class B) .................................................................................................. 18 Thermal measurement ............................................................................................................................... 20 11 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 11.10 11.11 Waveforms and scope plots ...........................................................................................21 Startup at low/high AC line input voltage with maximum load ............................................................. 21 Soft start ....................................................................................................................................................... 21 Drain and current sense voltage at maximum load................................................................................. 22 Zero crossing point during normal operation .......................................................................................... 22 Load transient response (Dynamic load from 10% to 100%) ................................................................. 23 Output ripple voltage at maximum load .................................................................................................. 23 Output ripple voltage at burst mode 1 W load ......................................................................................... 24 Active burst mode ....................................................................................................................................... 24 Over load protection (Auto Restart) .......................................................................................................... 25 VCC under voltage/Short optocoupler protection (Auto Restart).......................................................... 25 Output overvoltage protection (Latch mode) .......................................................................................... 26 12 References ...................................................................................................................27 Revision History ............................................................................................................................27 Application Note 2 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Abstract 1 Abstract This application note is an engineering report of 28 W 12V demo board designed in a quasi resonant flyback converter topology using ICE2QR1080G Quasi-resonant CoolSET™ .The target applications of ICE2QR1080G are set-top box, portable game controller, Blue-Ray/DVD player, netbook adapter and auxiliary power supply of PC, printer, TV, home theater/audio system, etc. With the CoolMOS™ integrated in this IC, it greatly simplifies the design and layout of the PCB. Due to valley switching, the turn on voltage is reduced and this offers higher conversion efficiency comparing to hard-switching flyback converter. With the DCM mode control, the reverse recovery problem of secondary rectify diode is relieved. And for its natural frequency jittering with line voltage, the EMI performance is better. Infineon’s digital frequency reduction technology enables a quasi-resonant operation till very low load. As a result, the system efficiency, over the entire load range, is significantly improved compared to conventional free running quasi resonant converter implemented with only maximum switching frequency limitation at light load. In addition, numerous adjustable protection functions have been implemented in ICE2QR1080G to protect the system and customize the IC for the chosen application. In case of failure modes, like open control-loop/over load, output overvoltage, and transformer short winding, the device switches into Auto Restart Mode or Latch-off Mode. By means of the cycle-by-cycle peak current limitation plus foldback point correction, the dimension of the transformer and current rating of the secondary diode can both be optimized.Thus, a cost effective solution can be easily achieved Application Note 3 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Demonstrator board 2 Demonstrator board This document contains the list of features, the power supply specification, schematic, bill of material and the transformer construction documentation. Typical operating characteristics such as performance curve and scope waveforms are showed at the rear of the report. Figure 1 DEMO-2QR1080G (Top View) ICE2QR1080G Figure 2 DEMO-2QR1080G (Bottom view) Application Note 4 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Specifications of Demonstrator Board 3 Table 1 Specifications of Demonstrator Board Specifications of DEMO-2QR1080G Input voltage and frequency 85 VAC (60 Hz) ~ 265 VAC (50Hz) Output voltage, current and power 12 V, 2.33 A, 28 W Dynamic load response (10% to 100% load, slew rate at 1.5 A/µs, 100 Hz) ±3% of nominal output voltage (Vripple_p_p < 280 mV) Output ripple voltage (full load, 85 VAC ~ 265 VAC) ±1% of nominal output voltage (Vripple_p_p< 60 mV) Active mode four point average efficiency (25%, 50%, 75%, 100% load) (EU CoC Version 5, Tier 1) > 86% at 115 VAC and > 87% 230 VAC 10% load efficiency (EU CoC Version 5, Tier 1) > 84% at 115 VAC and 230 VAC No load power consumption (EU CoC Version 5, Tier 1) < 50 mW at 265 VAC Conducted emissions (EN55022 class B) Pass with 10 dB margin for 115 VAC and 6 dB margin for 230 VAC ESD immunity (EN61000-4-2) Special Level (±16 kV for both contact and air discharge) Surge immunity (EN61000-4-5) Installation class 4 (±2 kV for line to line and ±4 kV for line to earth) Form factor case size (L x W x H) (120 x 52 x 26) mm3 Application Note 5 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Circuit description 4 Circuit description 4.1 Line input The AC line input side comprises the input fuse F1 as over-current protection. The choke L11, X-capacitor C11 and Y-capacitor C12 act as EMI suppressors. Optional spark gap devices SA1, SA2 and varistor VAR can absorb high voltage stress during lightning surge test. A rectified DC voltage (120~374 VDC) is obtained through the bridge rectifier BR1 together with bulk capacitor C13. 4.2 Start up Since there is a built-in startup cell in the ICE2QR1080G, there is no need for external start up resistor, which can improve standby performance significantly. When VVCC reaches the turn on voltage threshold 18V, the IC begins with a soft start. The soft-start implemented in ICE2QR1080G is a digital time-based function. The preset soft-start time is 12 ms with 4 steps. If not limited by other functions, the peak voltage on CS pin will increase step by step from 0.32 V to 1 V finally. After IC turns on, the VVCC voltage is supplied by auxiliary windings of the transformer. 4.3 Integrated MOSFET and PWM control ICE2QR1080G is comprised of a power MOSFET and the Quasi-Resonant controller; this integrated solution greatly simplifies the circuit layout and reduces the cost of PCB manufacturing. The PWM switch-on is determined by the zero-crossing input signal and the value of the up/down counter. The PWM switch-off is determined by the feedback signal VFB and the current sensing signal VCS. ICE2QR1080G also performs all necessary protection functions in flyback converters. Details about the information mentioned above are illustrated in the product datasheet. 4.4 RCD clamper circuit A clamper network (R11, C15 and D11) dissipates the energy of the leakage inductance and suppress ringing on the SMPS transformer. 4.5 Output stage On the secondary side, 12 V output, the power is coupled out via a schottky diode D21. The capacitor C22 and C23 provides energy buffering followed by the L-C filters L21 and C24 to reduce the output ripple and prevent interference between SMPS switching frequency and line frequency considerably. Storage capacitor C22 and C23 is designed to have an internal resistance (ESR) as small as possible. This is to minimize the output voltage ripple caused by the triangular current. 4.6 Feedback loop For feedback, the output is sensed by the voltage divider of R26 and R25 and compared to IC21 (TL431) internal reference voltage. C25, C26 and R24 comprise the compensation network. The output voltage of IC21 (TL431) is converted to the current signal via optocoupler IC12 and two resistors R22 and R23 for regulation control. Application Note 6 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Circuit description 4.7 Primary side peak current control The MOSFET drain source current is sensed via external resistor R14 and R14A. Since ICE2QR1080G is a current mode controller, it would have a cycle-by-cycle primary current and feedback voltage control which can make sure the maximum power of the converter is controlled in every switching cycle. For a Quasi-Resonant flyback converter, the maximum possible output power is increased when a constant current limit value is used for all the line input voltage range. This is usually not desired as this will increase additional cost on transformer and output diode in case of output over power conditions. The internal foldback point correction is implemented to adjust the VCS voltage limit according to the input line voltage. Here, the input line voltage is sensed using the current flowing out of ZC pin, during the MOSFET ontime. As the result, the maximum current limit will be lower at high input voltage and the maximum output power can be well limited versus the input voltage. 4.8 Digital frequency reduction During normal operation, the switching frequency for ICE2QR1080G is digitally reduced with decreasing load. At light load, the MOSFET will be turned on not at the first minimum drain-source voltage time, but on the nth. The counter is in range of 1 to 7, which depends on feedback voltage in a time-base. The feedback voltage decreases when the output power requirement decreases, and vice versa. Therefore, the counter is set by monitoring voltage VFB. The counter will be increased with low VFB and decreased with high VFB. The thresholds are preset inside the IC. 4.9 Active burst mode At light load condition, the SMPS enters into Active Burst Mode. At this stage, the controller is always active but the VVCC must be kept above the switch off threshold. During active burst mode, the efficiency increase significantly and at the same time it supports low ripple on Vout and fast response on load jump. For determination of entering Active Burst Mode operation, three conditions apply: 1. The feedback voltage is lower than the threshold of V FBEB(1.25 V). Accordingly, the peak current sense voltage across the shunt resistor is 0.17; 2. The up/down counter is 7; 3. And a certain blanking time (tBEB=24 ms). Once all of these conditions are fulfilled, the Active Burst Mode flip-flop is set and the controller enters Active Burst Mode operation. This multi-condition determination for entering Active Burst Mode operation prevents mis-triggering of entering Active Burst Mode operation, so that the controller enters Active Burst Mode operation only when the output power is really low during the preset blanking time. During active burst mode, the maximum current sense voltage is reduced from 1 V to 0.34 V so as to reduce the conduction loss and the audible noise. At the burst mode, the FB voltage is changing like a sawtooth between 3.0 V and 3.6 V. The feedback voltage immediately increases if there is a high load jump. This is observed by one comparator. As the current limit is 34% during Active Burst Mode a certain load is needed so that feedback voltage can exceed VFBLB (4.5 V). After leaving active burst mode, maximum current can now be provided to stabilize Vout. In addition, the up/down counter will be set to 1 immediately after leaving Active Burst Mode. This is helpful to decrease the output voltage undershoot. Application Note 7 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Protection features 5 Protection features 5.1 VVCC over voltage and under voltage protection During normal operation, the VCC voltage is continuously monitored. When the VCC voltage increases up to VCC,OVP or VCC voltage falls below the under voltage lock out level V CC,off, the IC will enter into autorestart mode. 5.2 Over load/Open loop protection In case of open control loop, feedback voltage is pulled up with internally block. After a fixed blanking time, the IC enters into auto restart mode. In case of secondary short-circuit or overload, regulation voltage VFB will also be pulled up, same protection is applied and IC will auto restart. 5.3 Over temperature protection The IC has a built-in over temperature protection function. When the controller’s temperature reaches 140°C, the IC will shut down switch and enters into auto restart. This can protect power MOSFET from overheated. 5.4 Adjustable output overvoltage protection During off-time of the power switch, the voltage at the zero-crossing pin ZC is monitored for output overvoltage detection. If the voltage is higher than the preset threshold 3.7 V for a preset period 100 μs, the IC is latched off. 5.5 Short winding protection The source current of the MOSFET is sensed via external resistor R14 and R14A. If the voltage at the current sensing pin is higher than the preset threshold V CSSW of 1.68 V during the on-time of the power switch, the IC is latched off. This constitutes a short winding protection. To avoid an accidental latch off, a spike blanking time of 190 ns is integrated in the output of internal comparator. Table 2 Protection function of ICE2QR1080G Protection Function Failure Condition Protection Mode VCC Overvoltage VVCC > 25 V & last for 10 μs (normal mode only) Auto Restart VCC Undervoltage/ Short Optocoupler VVCC < 10.5 V Auto Restart Overload/Open Loop VFB > 4.5 V & last for 30 ms Auto Restart Over Temperature (Controller Junction) TJ > 140 °C Auto Restart Output Overvoltage VZCOVP > 3.7 V & last for 100 μs Latch Short Winding VCSSW > 1.68 V & last for 190 ns Latch Application Note 8 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Circuit diagram 6 Figure 3 Circuit diagram Schematic of DEMO-2QR1080G Application Note 9 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Circuit diagram Note: 1. 2. 3. 4. 5. General guideline for layout design of Printed Cirduit Board (PCB): Star ground at bulk capacitor C13: all primary grounds should be connected to the ground of bulk capacitor C13 seperately in one point. It can reduce the switching noise going into the sensitive pins of CoolSET™ device effectively. The primary star ground can be split into five groups as follows, i. Signal ground includes all small signal grounds connecting to the CoolSET™ GND pin such as filter capacitor ground C17, C18, C19 and opto-coupler ground. ii. VCC ground includes the VCC capacitor ground C16 and the auxiliary winding ground, pin 5 of the power transformer. iii. Current Sense resistor ground includes current sense resistor R14 and R14A. iv. EMI return ground includes Y capacitor C12. v. DC ground from bridge rectifier, BR1 Filter capacitor close to the controller ground: Filter capacitors, C17, C18 and C19 should be placed as close to the controller ground and the controller pin as possible so as to reduce the switching noise coupled into the controller. High voltage traces clearance: High voltage traces should keep enough spacing to the nearby traces. Otherwise, arcing would incur. i. 400 V traces (positive rail of bulk capacitor C13) to nearby trace: > 2.0 mm ii. 600V traces (drain voltage of CoolSET™ IC11) to nearby trace: > 2.5 mm Recommended minimum 232mm2 copper area at drain pin to add on PCB for better thermal performance. Power loop area (bulk capacitor C13, primary winding of the transformer TR1 (Pin 1 and 3), IC11 Drain pin, IC11 CS pin and current sense resistor R14/R14A) should be as small as possible to minimize the switching emission. Application Note 10 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G PCB layout 7 PCB layout 7.1 Top side Figure 4 Top side component legend 7.2 Figure 5 Bottom side Bottom side copper and component legend Application Note 11 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Bill of material 8 Bill of material Table 3 Bill of material (V0.2) No. Designator Description Part Number Manufacturer 1 BR1 600V/2A DS2B60A Shindengen 1 2 C11 0.22µF/305V B32922C3224 Epcos 1 3 C12 2.2nF/250V DE1E3KX222MA4BN01F Murata 1 4 C13 82µF/450V 450BXW82MEFC16X35 Rubycon 1 5 C15 1nF/600V GRM31A7U2J102JW31D9 Murata 1 6 C16 22µF/50V 50PX22MEFC5X11 Rubycon 1 7 C17 100nF/50V GRM188R71H104KA93D Murata 1 8 C18, C26 1nF/50V GRM1885C1H102GA01D Murata 2 9 C19 39pF/50V GRM1885C1H390GA01D Murata 1 10 C22, C23 1200uF/16V 16ZLK1200M10X20 Rubycon 2 11 C24 680uF/16V 16ZLH680MEFC8X16 Rubycon 1 12 C25 220nF/50V GRM188R71H224KAC4D Murata 1 13 D11 0.8A/600V D1NK60 Shindengen 1 14 D12 0.25A/200V BAS21-03W Infineon 1 15 D21 30A/100V STPS30M100SFP 1 16 F1 1.6A/300V 36911600000 1 17 HS1 Heat Sink(D21) 574502B03300G 1 18 IC11 ICE2QR1080G(DSO-16/12) ICE2QR1080G 19 IC12 SFH617A-3((DIP-4) SFH617A-3 1 20 IC21 TL431ABVLPG(TO-92) TL431ABVLPG 1 21 L11 47mH/0.65A 750342434 Wurth Electronics 1 22 L21 2.2uH/4.3A 744 746 202 2 Wurth Electronics 1 23 R11 68k/2W/500V RSF200JB-73-68K 1 24 R12, R13 10Ω(0603) 10Ω(0603) 2 25 R14, R14A 1.1Ω/0.75W ERJB2BF1R1V 2 26 R15 36kΩ/0603 0603 1 27 R16 8.3kΩ/0603 0603 1 28 R22 820Ω/0603 0603 1 29 R23 1.2kΩ/0603 0603 1 30 R24 68kΩ/0603 0603 1 31 R25 38kΩ/0603(1%) 0603(1%) 1 32 R26 10kΩ/0603(1%) 0603(1%) 1 33 TR1 639µH(72:11:14) 750343051 34 Test point BA,FB,CS,Drain,Vcc,Gnd 5003 35 VAR 300V/0.25W B72207S2301K101 36 ZD11 22V Zener UDZS22B 37 (L N), (+12V Com) Connector 691102710002 Application Note 12 Infineon Wurth Electronics Quantity 1 1 1 Epcos 1 1 Wurth Electronics 2 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Transformer construction 9 Transformer construction Core and material: EE25/13/7(EF25), TP4A (TDG) Bobbin: 14-Pins, THT, horizontal version (070-5644) Primary Inductance: LP = 639 µH (±10%), measured between pin 1 and pin 3 Manufacturer and part number: Wurth Electronics Midcom (750343051) Figure 6 Start Stop No. of turns Wire size 3 14 2 12 36 11 1xAWG#27 1xLitz TIW(7xAWG#29) 1 Layer 2 1 36 1xAWG#27 1 7 6 14 1xAWG#30 /2 Primary Secondary /2 Primary Auxiliary Transformer structure Application Note 13 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Test results 10 Test results 10.1 Efficiency, regulation and output ripple Table 4 Efficiency, regulation & output ripple Input (VAC/Hz) 85 VAC/60 Hz 115 VAC/60 Hz 230 VAC/50 Hz 265VAC/50 Hz Application Note Pout (W) Efficiency (η) (%) 50.31 2.83 85.79 0.58 9.02 7.08 86.31 12.15 1.17 15.82 14.15 85.22 25.03 12.15 1.75 18.53 21.23 84.83 34.16 12.15 2.33 32.36 28.31 82.87 0.03064 12.15 0.00 42.44 3.28 12.15 0.23 51.69 2.83 86.31 8.14 12.15 0.58 8.27 7.08 86.95 16.31 12.15 1.17 13.29 14.15 86.79 24.45 12.15 1.75 13.73 21.23 86.84 32.87 12.15 2.33 19.33 28.31 86.13 0.03217 12.15 0.00 46.80 3.31 12.15 0.23 55.07 2.83 85.53 8.27 12.15 0.58 8.49 7.08 85.58 16.15 12.15 1.17 10.58 14.15 87.65 24.03 12.15 1.75 11.51 21.23 88.36 31.96 12.15 2.33 17.47 28.31 88.58 0.03342 12.15 0.00 45.78 3.33 12.15 0.23 57.38 2.83 85.01 8.35 12.15 0.58 8.62 7.08 84.76 16.20 12.15 1.17 10.31 14.15 87.38 24.05 12.15 1.75 11.82 21.23 88.28 31.98 12.15 2.33 12.40 28.31 88.52 Pin (W) Vout (VDC) Iout (A) VOutRPP (mV) 0.03115 12.15 0.00 42.80 3.30 12.15 0.23 8.20 12.15 16.61 14 Average η (%) OLP Pin (W) OLP Iout (A) 44.73 2.99 43.62 3.06 44.51 3.26 44.8 3.29 84.81 86.67 87.54 87.23 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Test results Figure 7 Efficiency vs AC line input voltage Figure 8 Efficiency vs output power at 115 VAC and 230 VAC line Application Note 15 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Test results 10.2 Figure 9 Standby power Standby power at no load vs AC line input voltage (measured by Yokogawa WT210 power meter - integration mode) 10.3 Figure 10 Line regulation Line regulation Vout at full load vs AC line input voltage Application Note 16 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Test results 10.4 Figure 11 Load regulation Load regulation Vout vs output power 10.5 Figure 12 Maximum input power Maximum input power (before over-load protection) vs AC line input voltage 10.6 ESD immunity (EN61000-4-2) Pass EN61000-4-2 Special Level (±16 kV for both contact and air discharge). 10.7 Surge immunity (EN61000-4-5) Pass EN61000-4-5 Installation class 4 (±2 kV for line to line and ±4 kV for line to earth)1. 1 HS1 change to ATS-PCBT1093 Application Note 17 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Test results 10.8 Conducted emissions (EN55022 class B) The conducted EMI was measured by Schaffner (SMR4503) and followed the test standard of EN55022 (CISPR 22) class B. The demo board was set up at maximum load (28 W) with input voltage of 115 VAC and 230 VAC. Figure 13 Conducted emissions(Line) at 115 VAC and maximum Load Figure 14 Conducted emissions(Neutral) at 115 V AC and maximum Load Pass conducted emissions EN55022 (CISPR 22) class B with 10 dB margin for quasi peak limit at low line (115 VAC). Application Note 18 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Test results Figure 15 Conducted emissions(line) at 230 VAC and maximum Load Figure 16 Conducted emissions(Neutral) at 230 V AC and maximum Load Pass conducted emissions EN55022 (CISPR 22) class B with 6 dB margin for quasi peak limit at high line (230 VAC). Application Note 19 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Test results 10.9 Thermal measurement The thermal test of open frame demo board was done using an infrared thermography camera (TVS-500EX) at ambient temperature 25°C. The measurements were taken after two hours running at full load. Table 5 Hottest temperature of demo board No. Major component 85 VAC (°C) 265 VAC (°C) 1 IC11 (2QR1080G) 62.5 55.4 2 R14 (current sense resistor) 52.2 40.4 3 TR1 (transformer) 57.5 58.8 4 BR1 (bridge diode) 53.8 33.4 5 R11(clamper resistor) 37.2 34.3 6 L11 (EMI choke) 97.9 36.9 7 D21 (secondary diode) 61.5 61.6 8 Ambient 25 25 . Figure 17 85 VAC full load and 25⁰C ambient 265 VAC full load and 25⁰C ambient PCB top side PCB top side PCB bottom side Infrared thermal image of DEMO-2QR1080G PCB bottom side Figure 18 Application Note 20 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Waveforms and scope plots 11 Waveforms and scope plots All waveforms and scope plots were recorded with a TELEDYNELECROY 606Zi oscilloscope. 11.1 C1 (Yellow) C2 (Purple) C2 (Blue) C2 (Green) Startup at low/high AC line input voltage with maximum load : Drain voltage (VD) : Supply voltage (VVCC) : Feedback voltage (VFB) : Zero crossing voltage (VZC) C1 (Yellow) C2 (Purple) C2 (Blue) C2 (Green) Startup time at 85 VAC and maximum load ≈ 500 ms Figure 19 Startup 11.2 C1 (Yellow) C2 (Purple) C2 (Blue) C2 (Green) : Drain voltage (VD) : Supply voltage (VVCC) : Feedback voltage (VFB) : Zero crossing voltage (VZC) Startup time at 265 VAC and maximum load ≈ 500 ms Soft start : Current sense voltage (VCS) : Supply voltage (VVCC) : Feedback voltage (VFB) : Zero crossing voltage (VZC) Soft start time at 85 VAC and maximum load ≈ 13 ms Figure 20 Soft start Application Note 21 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Waveforms and scope plots 11.3 C1 (Yellow) C2 (Purple) Drain and current sense voltage at maximum load : Drain voltage (VDrain) : Current sense voltage (VCS) C1 (Yellow) C2 (Purple) : Drain voltage (VDrain) : Current sense voltage (VCS) VDrain_peak at 85 VAC ≈ 321 V VDrain_peak at 265 VAC ≈ 587 V Figure 21 Drain and current sense voltage at maximum load 11.4 C1 (Yellow) C2 (Purple) Zero crossing point during normal operation : Drain voltage (VDrain) : Current sense voltage (VCS) 2nd zero crossing at 85 VAC Figure 22 Zero corssing Application Note C1 (Yellow) C2 (Purple) : Drain voltage (VDrain) : Current sense voltage (VCS) 7th zero crossing at 85 VAC 22 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Waveforms and scope plots 11.5 Load transient response (Dynamic load from 10% to 100%) C1 (Yellow) : Output ripple voltage (Vout) C2 (Purple) : Output current (Iout) Vripple_pk_pk at 85 VAC ≈ 206 mV (Load change from 10% to 100% at 85 VAC,100 Hz,0.4 A/μs slew rate) Probe terminal end with decoupling capacitor of 0.1 μF(ceramic) and 1 μF(Electrolytic), 20 MHz filter Figure 23 Load transient response 11.6 C1 (Yellow) C2 (Purple) C1 (Yellow) : Output ripple voltage (Vout) C2 (Purple) : Output current (Iout) Vripple_pk_pk at 265 VAC ≈ 279 mV (Load change from10% to 100% at 2100 VAC,100 Hz,0.4 A/μs slew rate) Probe terminal end with decoupling capacitor of 0.1 μF(ceramic) and 1 μF(Electrolytic), 20 MHz filter Output ripple voltage at maximum load : Output ripple voltage (Vout) : Output current (Iout) C1 (Yellow) C2 (Purple) : Output ripple voltage (Vout) : Output current (Iout) Vripple_pk_pk at 85 VAC ≈ 23 mV Vripple_pk_pk at 265 VAC ≈ 13 mV Probe terminal end with decoupling capacitor of 0.1 Probe terminal end with decoupling capacitor of 0.1 μF(ceramic) and 1 μF(Electrolytic), 20 MHz filter μF(ceramic) and 1 μF(Electrolytic), 20 MHz filter Figure 24 Output ripple voltage at maximum load Application Note 23 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Waveforms and scope plots 11.7 C1 (Yellow) C2 (Purple) Output ripple voltage at burst mode 1 W load : Output ripple voltage (Vout) : Output current (Iout) C1 (Yellow) C2 (Purple) : Output ripple voltage (Vout) : Output current (Iout) Vripple_pk_pk at 85 VAC ≈ 51 mV Vripple_pk_pk at 265 VAC ≈ 59 mV Probe terminal end with decoupling capacitor of 0.1 Probe terminal end with decoupling capacitor of 0.1 μF(ceramic) and 1 μF(Electrolytic), 20 MHz filter μF(ceramic) and 1 μF(Electrolytic), 20 MHz filter Figure 25 Output ripple voltage at burst mode 1 W load 11.8 Active burst mode C1 (Yellow) : Current sense voltage (VCS) C2 (Purple) : Supply voltage (VVCC) C2 (Blue) : Feedback voltage (VFB) C2 (Green) : Zero crossing voltage (VZC) Condition to enter burst: VFB<1.2 V, NZC=7 and tblanking =24 ms (load change form full load to 1 W load at 85 VAC) Figure 26 Active burst mode Application Note C1 (Yellow) : Current sense voltage (VCS) C2 (Purple) : Supply voltage (VVCC) C2 (Blue) : Feedback voltage (VFB) C2 (Green) : Zero crossing voltage (VZC) Condition to leave burst: VFB>4.5 V (load change form full load to 1 W to full load at 85 VAC) 24 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Waveforms and scope plots 11.9 Over load protection (Auto Restart) C1 (Yellow) : Drain voltage (VD) C2 (Purple) : Supply voltage (VVCC) C2 (Blue) : Feedback voltage (VFB) C2 (Green) : Zero crossing voltage (VZC) Condition to enter over load protection: VFB>4.5 V & last for 40ms blanking time (output load change from 2.33 A to 3.5 A at 85 VAC) Figure 27 Over load protection 11.10 VCC under voltage/Short optocoupler protection (Auto Restart) C1 (Yellow) : Drain voltage (VD) C2 (Purple) : Supply voltage (VVCC) C2 (Blue) : Feedback voltage (VFB) C2 (Green) : Zero crossing voltage (VZC) Condition to enter VCC under voltage protection: VCC < 10.5 V (short the transistor of optocoupler(Pin 3 and 4 of IC12) during system operating at full load and release at 85 VAC) Figure 28 VCC under voltage/short optocoupler protection Application Note 25 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G Waveforms and scope plots 11.11 Output overvoltage protection (Latch mode) C1 (Yellow) : Output voltage (Vout) C2 (Purple) : Supply voltage (VVCC) C2 (Blue) : Feedback voltage (VFB) C2 (Green) : Zero crossing voltage (VZC) Condition to enter external protection enable: Vout >14 V (VZC>3.7 V) (85 VAC, short R26 during while system operation at no load) Figure 29 External auto restart enableOutput overvoltage protection Application Note 26 Revision 1.0 2016-04-15 28W 12V SMPS Demo Board with ICE2QR1080G AN-DEMO-2QR1080G References 12 References [1] ICE2QR1080G datasheet, Infineon Technologies AG [2] AN-PS0025-CoolSET F3R DIP-8, DIP-7, DSO-16/12 new jitter version design guide-V2.2 Revision History Major changes since the last revision Page or Reference -- Application Note Description of change First release. 27 Revision 1.0 2016-04-15 Trademarks of Infineon Technologies AG AURIX™, C166™, CanPAK™, CIPOS™, CoolGaN™, CoolMOS™, CoolSET™, CoolSiC™, CORECONTROL™, CROSSAVE™, DAVE™, DI-POL™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, Infineon™, ISOFACE™, IsoPACK™, i-Wafer™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OmniTune™, OPTIGA™, OptiMOS™, ORIGA™, POWERCODE™, PRIMARION™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, ReverSave™, SatRIC™, SIEGET™, SIPMOS™, SmartLEWIS™, SOLID FLASH™, SPOC™, TEMPFET™, thinQ!™, TRENCHSTOP™, TriCore™. Trademarks updated August 2015 Other Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2016-04-15 Published by Infineon Technologies AG 81726 Munich, Germany ©ANDEMO_201510_PL21_004owners. 2016 Infineon Technologies AG. All Rights Reserved. Do you have a question about this document? Email: [email protected] Document reference ANDEMO_201510_PL21_006 IMPORTANT NOTICE The information contained in this application note is given as a hint for the implementation of the product only and shall in no event be regarded as a description or warranty of a certain functionality, condition or quality of the product. Before implementation of the product, the recipient of this application note must verify any function and other technical information given herein in the real application. Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind (including without limitation warranties of non-infringement of intellectual property rights of any third party) with respect to any and all information given in this application note. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on the product, technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.