TDA8037 Low power 3V smart card interface Rev. 1.1 — 17 November 2014 Product data sheet 1. General description The TDA8037 is the cost efficient successor of the established integrated contact smart card reader IC TDA8035. It offers a high level of security for the card performing current limitation, short circuit detection, ESD protection as well as supply supervision. Operating in 3 V supply domain, the current consumption during the shutdown mode of the contact reader is very low. It is therefore the ideal component for a power efficient contact reader. 2. Features and benefits 2.1 Protection of the contact smart card Thermal and short-circuit protection on all card contacts VCC regulation: 3 V 5 % on 2 220 nF multilayer ceramic capacitors with low ESR Current spikes of 40 nA up to 20 MHz, with controlled rise and fall times, filtered overload detection approximately 120 mA Automatic activation and deactivation sequences initiated by software or by hardware in the event of a short-circuit, card take-off, overheating, VDDhost, VREG and VDD dropping Enhanced card-side ElectroStatic Discharge (ESD) protection of (> 8 kV) Supply supervisor for killing spikes during power on and off: threshold internally fixed externally by a resistor bridge (with SO28 package only) 2.2 Easy integration into your contact reader SW compatible to TDA8024, TDA8034 and TDA8035 3 V smart card supply Three protected half-duplex bidirectional buffered I/O lines (C4, C7 and C8) External clock input up to 20 MHz Card clock generation up to 20 MHz using pin CLKDIV with synchronous frequency changes of fCLKIN, fCLKIN/2 (with SO28 package only) Non-inverted control of pin RST using pin RSTIN Built-in debouncing on card presence contact Multiplexed status signal using pin OFFN Chip Select digital input for parallel operation of several TDA8037 ICs (with SO28 package only) TDA8037 NXP Semiconductors Low power 3V smart card interface 2.2.1 Other TSSOP16 and SO28 package SO28 version is footprint compatible with TDA8024T Compliant with ISO 7816, Cisco technology and EMV 4.3 payment systems 3. Applications Pay TV Electronic payment Identification IC card readers for banking 4. Quick reference data Table 1. Quick reference data VDDP = 3.3 V; VDD(INTF) = 3.3 V; fXtal = 10 MHz; GND = 0 V; Tamb = 25 C; unless otherwise specified Symbol Parameter Conditions Min Typ Max Unit 3 3.3 3.6 V - 250 400 A active mode; CLK = CLKIN; no-load - - 5 mA active mode; CLK = CLKIN; ICC = 65 mA - - 70 mA 2.85 - 3.15 V Supply VDD supply voltage IDD supply current Shutdown mode; fCLKIN = stopped Supply voltage for the card: pin VCC VCC supply voltage DC ICC < 65 mA AC current spikes of 40 nA 2.76 - 3.24 V Vripple(p-p) peak-to-peak ripple voltage from 20 kHz to 200 MHz - - 150 mV ICC supply current - - 65 mA General tdeact deactivation time total sequence 35 90 250 s Ptot total power dissipation Tamb = 25 C to +85 C - - 0.1 W Tamb ambient temperature 25 - +85 C 5. Ordering information Table 2. Ordering information Type number Package Name Description Version TDA8037TT TSSOP16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 TDA8037T SO28 plastic small outline package; 28 leads; body width 7.5 mm SOT136-1 TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 2 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 6. Block diagram VDD VDDhost 10 µF PORADJ 100 nF VDD GND TEST VDD CS INTERNAL REGULATOR CMDVCCN CLKDIV LATCH input sense SUPERVISOR VCC reset and supalarm 2x 220 nF RSTIN RST BANDGAP HOST INTERFACE INTERNAL OSCILLATOR I/OUC UC AUX1UC configurations bus for smartcard THERMAL PROTECTION reader interface HZ AUX2UC interruption VDD HZ OFFN CLK ISO7816 READER INTERFACE CARD CONNECTOR c5 c1 c6 c2 c7 c3 c8 c4 AUX1 AUX2 DIGITAL SEQUENCER I/O CLOCK CIRCUITRY CLKIN TDA8037 PRESN aaa-011372 Fig 1. Block diagram TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 3 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 7. Pinning information 7.1 Pinning AUX1UC 1 16 I/OUC AUX2UC 2 15 CLKIN VDD 3 14 OFFN PRESN 4 I/O 5 AUX2 6 AUX1 7 GND 8 13 RSTIN TDA8037TT 12 CMDVCCN 11 VCC 10 RST 9 CLK aaa-011373 Fig 2. Pin configuration TSSOP16 7.2 Pinning CLKDIV 1 28 AUX2UC n.c. 2 27 AUX1UC n.c. 3 26 I/OUC TEST 4 25 n.c. n.c. 5 24 CLKIN VDD 6 23 OFFN n.c. 7 n.c. 8 PRESN 9 TDA8037T 22 n.c. 21 CS 20 RSTIN n.c. 10 19 CMDVCCN I/O 11 18 PORADJ AUX2 12 17 VCC AUX1 13 16 RST GND 14 15 CLK aaa-011374 Fig 3. TDA8037 Product data sheet Pin configuration SO28 All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 4 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 7.3 Pin description Table 3. Pin description Symbol Pin Pin SO28 TSSOP16 Supply Type Description AUX1UC 27 1 VDD I/O auxiliary data line to/from the host (internal 10 k pull-up resistor to VDD) AUX2UC 28 2 VDD I/O auxiliary data line to/from the host (internal 10 k pull-up resistor to VDD) VDD 6 3 VDD supply supply voltage PRESN 9 4 VDD I card presence contact input (active LOW); if PRESN is true, then the card is considered as present. A debouncing feature of 4.05 ms typ. is built in. I/O 11 5 VCC I/O data line to/from the card (C7)(internal 10 k pull up resistor to VCC) AUX2 12 6 VCC I/O auxiliary data line to/from the card (C8) (internal 10 k pull up resistor to VCC) AUX1 13 7 VCC I/O auxiliary data line to/from the card (C4) (internal 10 k pull up resistor to VCC) GND 14 8 - supply ground CLK 15 9 VCC O clock to the card (C3) RST 16 10 VCC O card reset (C2) VCC 17 11 VCC O supply for the card (C1) (decouple to GND with 2x 220 nF capacitors with ESR<100 m). CMDVCCN 19 12 VDD I start activation sequence input from the host (active LOW) RSTIN 20 13 VDD I card reset input from the host (active HIGH) OFFN 23 14 VDD O NMOS interrupt to the host (active LOW) with 10 k internal pull-up resistor to VDD (see fault detection) CLKIN 24 15 VDD I external clock I/OUC 26 16 VDD I/O host data I/O line (internal 10k pull-up resistor to VDD) CLKDIV 1 nc VDD I control for choosing CLK frequency TEST 4 nc VDD I test mode PORADJ 18 nc VDD I input for VDDhost supervisor. PORADJ threshold can be changed with an external R bridge. CS 21 nc VDD I chip select input from the host (active High) TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 5 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 8. Functional description Remark: The ISO 7816 terminology convention has been adhered to throughout this document, and it is assumed that the reader is familiar with this convention. 8.1 Power supply Power supply voltage VDD is from 3 V to 3.6 V. All interface signals with the system controller are referenced to VDD. All card contacts remain inactive during powering up or powering down. Internal regulator VREG is 1.8 V. After powering the device, OFFN remains low until CMDVCCN is set high and PRESN is low. During power off, OFFN falls low when VDD is below the threshold voltage falling. The frequency of the internal oscillator (fosc(int)) used for the activation sequences is put in low frequency mode. It is to save power consumption while CMDVCCN is kept at high level (card not activated). 8.2 Voltage supervisor VDD VDD VREG REFERENCE VOLTAGE Nand VDDhost PORADJ aaa-011375 Fig 4. Block voltage supervisor The voltage supervisor is used as a power-on reset, and also as supply drop detection during a card session. The threshold of the voltage supervisor is set internally in the IC for VDD and VREG. The threshold can be adjusted externally for VDDhost using the PORADJ pin. As long as VDD is less than Vth(VDD) + Vhys(VDD), the IC remains inactive whatever the levels on the command lines are. It lasts during tw after VDD has reached a level higher than Vth(VDD) + Vhys(VDD).The outputs of the VDD, VREG and VDDhost supervisors, are combined and sent to a digital controller in order to reset the TDA8037. The defined reset TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 6 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface pulse of approximately 5.7 ms (tw = 2048 1/(fosc(int)_Low), is used internally for maintaining the IC in an inactive mode during the supply voltage power-on (see Figure 5, Figure 6, Figure 7, Figure 8 and Figure 9). When VDD falls below Vth(VDD), Vth(VREG) or VDDhost falls below Vth(VDDhost), a deactivation sequence is performed. Vth_VDD_LH VDD Vth_VDD_LH Vth_VDD_HL Vt VSUP (internal signal) X tw tw reset (internal signal) X tw tw SUPALARM (internal signal) X debouncing debouncing OFFN X aaa-011376 Fig 5. Voltage supervisor 8.3 Clock circuitry To generate the card clock CLK, the TDA8037 uses an external clock provided on CLKIN pin. Apply the external clock to CLKIN before CMDVCCN falling edge signal. The frequency is chosen as fCLKIN, fCLKIN/2 via the pins CLKDIV. The frequency change is synchronous, which means that during transition, no pulse is shorter than 45 % of the smallest period. It ensures that the first and last clock pulse around the change has the correct width. When changing the frequency dynamically, the change is effective for only 10 periods of CLKIN after the command. The duty cycle on pin CLK shall be between 45 % and 55 %. Table 4. Clock configuration (SO28 only) CLKDIV CLK 0 fCLKIN 1 fCLKIN/2 8.4 I/O circuitry The three data lines I/O, AUX1 and AUX2 are identical. By pulling both lines (I/O and I/OUC) HIGH via a 10 k resistor (I/O to VCC and I/OUC to VDD), the idle state is realized. I/O is referenced to VCC, and I/OUC to VDD, thus allowing operation with VCC VDD. TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 7 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface The first side on which a falling edge occurs becomes the master. An anti-latch circuit disables the detection of falling edges on the other line, which becomes a slave. After a time delay td(edge), the logic 0 on the master side is transmitted to the slave side. When the master side returns to logic 1, the slave side transmits the logic 1 during the time delay tpu. After which, both sides return to their Idle states. This active pull-up feature ensures fast Low to High transitions. It is able to deliver more than 1 mA up to an output voltage of 0.9 VCC on an 80 pF load. At the end of the active pull-up pulse, the output voltage only depends on the internal pull-up resistor, and on the load current. The current to/from the cards I/O lines, is internally limited to 15 mA. The maximum frequency on these lines is 1.5 MHz. 8.5 CS control The CS (Chip Select) input allows multiple devices to operate in parallel. When CS is high, the system interface signals operate as described. When CS is low, the signals CMDVCCN, RSTIN and CLKDIV are latched. I/OUC, AUX1UC and AUX2UC are set to high impedance pull-up mode and data is no longer passed to or from the smart card. The OFFN output is a 3-state output. 8.6 Shutdown mode After power-on reset, the circuit enters the Shutdown mode if CMDVCCN input pin is set to a logic high. A minimum number of circuits are active while waiting for the microcontroller to start a session. 1. All card contacts are inactive (approximately 200 to GND). 2. I/OUC, AUX1UC and AUX2UC are high impedance (10 k pull-up resistor connected to VDD). 3. Voltage generators are stopped. 4. Voltage supervisor is active. 5. The internal oscillator runs at its low frequency. TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 8 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 8.7 Activation sequence The following sequence then occurs with external clock (see Figure 6): T = 64 Toscint (freq high) 1. CMDVCCN is pulled Low (t0) 2. The internal oscillator changes to its high frequency (t1 = t0+~) 3. VCC rises from 0 to selected VCC value (3 V) with a controlled slope ((t2 = t1 + 3T/2) 4. I/O, AUX1 and AUX2 are enabled (t3 = t1 + 10T); they were pulled LOW until this moment 5. CLK is applied to the C3 contact (t4 = t3 + x) with 200 ns < x < 10 1/fCLKIN 6. RST is enabled (t5 = t1 + 13T). OSCINT CLKIN CMDVCCN VCC ATR I/O CLK RST RSTIN I/OUC t0 t1 Fig 6. TDA8037 Product data sheet t2 t3 t4 t5 aaa-011377 Activation sequence at t3 All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 9 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 8.8 Deactivation sequence When a session is completed, the microcontroller sets the CMDVCCN line to the HIGH state. The circuit then executes an automatic deactivation sequence by counting the sequencer back and ends in the inactive state (see Figure 7): Note: CMDVCCN line should not be set to High state until activation sequence has not completed. Else, this deactivation command is not taken into account. 1. RST goes LOW (t11 = t10 + 3T/64) 2. CLK is stopped LOW (t12 = t11 +T/2) 3. I/O, AUX1 and AUX2 are pulled LOW (t13 = t11 + T) 4. VCC falls to zero (t14 = t11 + 3T/2). The deactivation sequence is completed when VCC reaches its inactive state 5. VCC < 0.4 V (tde = t11 + 3T/2 + VCC fall time) 6. All card contacts become low-impedance to GND. I/OUC, AUX1UC and AUX2UC remain pulled up to VDD via a 10 k resistor. 7. The internal oscillator reverts to its lower frequency. OSCINT CLKIN CMDVCCN VCC I/O CLK RST t10 t11 t12 t13 t14 Fig 7. tdeact aaa-011378 Deactivation sequence 8.9 VCC regulator VCC buffer is able to deliver up to 65 mA continuously at VCC = 3 V. It has an internal overload detection at approximately 125 mA. This detection is internally filtered, allowing the card to draw spurious current pulses up to 200 mA for some ms, without causing a deactivation. The average current value must stay below maximum. TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 10 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 8.10 Fault detection The circuit monitors the following fault conditions: • • • • short-circuit or high current on VCC Card removal during transaction VDD, VREG or VDDhost dropping overheating. There are two different cases (see Figure 8 on page 12): 1. CMDVCCN High: (outside a card session) then, if the card is not in the reader, OFFN is Low. It is High when the card is in the reader. The supply supervisor detects a supply voltage drop on VDD. It generates an internal power-on reset pulse, but does not act upon OFFN. The card is not powered-up, so no short-circuit or overheating is detected. 2. CMDVCCN Low: (within a card session) then, OFFN falls Low in any of the aforementioned cases. As soon as the fault is detected, an emergency deactivation is automatically performed. When the system controller sets CMDVCCN back to High, it may sense OFFN again after complete deactivation sequence. It does it to distinguish between a hardware problem or a card extraction. If the card is still present, OFFN then returns High. A bounce may occur on PRESN signal during card insertion or withdrawal. It depends on the type of card presence switch within the connector (normally close or normally open), and on the mechanical characteristics of the switch. To counter the bounce, a debounce feature of approximately 4.05 ms (tdeb = 1280 1/(fosc(int)_Low) is integrated in the device. When the card is inserted, OFFN goes High only at the end of the debounce time (see Figure 9 on page 12). When the card is extracted, an automatic deactivation sequence of the card is performed on the first True/False transition on PRESN, and OFFN goes Low. TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 11 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface OSCINT CLKIN PRESN OFFN VCC I/O CLK RST t10 t11 t12 t13 t14 Fig 8. tdeact aaa-011379 Emergency deactivation sequence (card extraction) PRESN OFFN CMDVCCN tdeb VCC tdeb (1) (2) aaa-011380 Fig 9. Behavior of OFFN, CMDVCCN, PRESN and VCC TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 12 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 9. Limiting values All card contacts are protected against a short-circuit with any other card contact. Stress beyond the limiting values can damage the device permanently. The values are stress ratings only and functional operation of the device under these conditions is not implied. Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VDD supply voltage Conditions VIH HIGH-level input voltage Min Max Unit 0.3 +4.5 V CS, CLKDIV, PORADJ, PRESN, CMDVCCN, RSTIN, OFFN, CLKIN, I/OUC, AUX1UC, AUX2UC, VDD 0.3 +4.5 V I/O, RST, AUX1, AUX2 and CLK 0.3 +4.5 V Tamb ambient temperature 25 +85 C Tstg storage temperature 55 +150 C Tj junction temperature - 125 C Ptot total power dissipation Tamb = -25 C to +85 C - 0.1 W VESD electrostatic discharge voltage Human Body Model (HBM) on card pins I/O, RST, VCC, AUX1, CLK, AUX2, PRESN within typical application 8 +8 kV Human Body Model (HBM) on all other pins 2 +2 kV Machine Model (MM) on all pins 200 +200 V Field Charged Device Model (FCDM) on all pins 500 +500 V 10. Thermal characteristics TDA8037 Product data sheet Table 6. Thermal characteristics Symbol Package name Parameter Conditions Typ Unit Rth(j-a) TSSOP16 thermal resistance from junction to ambient in free air 160 °C/W Rth(j-a) SO28 thermal resistance from junction to ambient in free air 69 °C/W All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 13 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 11. Characteristics Table 7. Characteristics of IC VDD = 3.3 V; Clock in = 10 MHz; GND = 0 V; Tamb = 25 C; unless otherwise specified Symbol Parameter Conditions Min Typ Max Shutdown mode; active mode; CLK = CLKIN; No-load Unit 3 3.3 3.6 V - 250 400 A - - 5 mA active mode; CLK=CLKIN; ICC = 65 mA - - 70 mA falling 1.20 1.35 1.5 V 60 75 90 mV 2.45 2.6 2.75 V 10 50 100 mV Supply voltage VDD supply voltage IDD supply current fCLKIN = stopped Vth(VREG) VREG threshold voltage Vhys(VREG) VREG hysteresis voltage Vth(VDD) VDD threshold voltage Vhys(VDD) VDD hysteresis voltage tw pulse width Vth(L)(PORADJ) LOW-level threshold falling external resistors on PORADJ 4.87 6.82 11.3 ms 0.75 0.84 0.93 V 20 75 130 mV 1 - +1 A 1.62 1.8 1.98 V 396 - 484 nF voltage on pin PORADJ Vhys(PORADJ) hysteresis voltage on pin PORADJ IL leakage current pin PORADJ VREG Vo output voltage Card supply voltage (VCC) [1] Cdec decoupling capacitance connected on VCC (220 nF + 220 nF 10 %) Vo output voltage inactive mode; no load 0.1 - +0.1 V inactive mode; Io = 1 mA 0.1 - +0.3 V inactive mode - - 1 mA active mode; ICC < 65 mA DC 2.85 3.05 3.15 V active mode; current pulses of 40 nA/s with ICC < 200 mA, t < 400 ns; 2.76 - 3.20 V from 20 kHz to 200 MHz - - 150 mV Io output current VCC supply voltage at grounded pin VCC Vripple(p-p) peak-to-peak ripple voltage ICC supply current - - 65 mA SR slew rate 0.030 0.075 0.120 V/s External clock (CLKIN) fext(CLKIN) external frequency on pin CLKIN 1 - 20 MHz duty cycle 48 - 52 % VIL LOW-level input voltage 0.3 - 0.3VDD V TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 14 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface Table 7. Characteristics of IC …continued VDD = 3.3 V; Clock in = 10 MHz; GND = 0 V; Tamb = 25 C; unless otherwise specified Symbol Parameter VIH HIGH-level input voltage tr(i) input rise time tf(i) Conditions input fall time Min Typ Max Unit 0.7VDD - VDD + 0.3 V fCLK = fCLKIN = 20 MHz on external clock - - 4 ns fCLK = fCLKIN = 10 MHz on external clock - - 8 ns fCLK = fCLKIN = 5 MHz on external clock - - 16 ns fCLK = fCLKIN = 20 MHz on external clock - - 4 ns fCLK = fCLKIN = 10 MHz on external clock - - 8 ns fCLK = fCLKIN = 5 MHz on external clock - - 16 ns - - 200 ns 200 - 400 ns Data lines (pins I/O, I/OUC, AUX1, AUX2, AUXIUC, AUX2UC) td delay time falling edge on pins I/O and I/OUC or I/OUC and I/O tw(pu) pull-up pulse width fmax maximum frequency on data lines - - 1 MHz Ci input capacitance on data lines - - 10 pF Data lines to the card (pins I/O, AUX1, AUX2); (Integrated 10 k pull-up resistor connected to VCC) Vo Io output voltage output current inactive mode; no load 0 - 0.1 V inactive mode; Io = 1 mA 0 - 0.3 V inactive mode - - 1 mA 0 - 0.3 V at grounded pin I/O VOL LOW-level output voltage IOL = 1 mA VOH HIGH-level output voltage No DC load IOL 15 mA VCC 0.4 - VCC V 0.9VCC - VCC + 0.1 V VCC + 0.1 V V IOH < 40 A 0.75VCC IOH 15 mA 0 - 0.4 VIL LOW-level input voltage 0.3 - +0.8 V VIH HIGH-level input voltage 0.6VCC - VCC + 0.3 V Vhys hysteresis voltage on I/O 30 115 200 mV IIL LOW-level input current on I/O; VIL =0 - - 600 A IIH HIGH-level input current on I/O; VIH = VCC - - 10 A tr(i) input rise time from VIL max to VIH min - - 1.2 s tf(i) input fall time from VIL max to VIH min - - 1.2 s tr(o) output rise time CL <= 80 pF; 10 % to 90 % from 0 to VCC - - 0.1 s tf(o) output fall time CL <= 80 pF; 10 % to 90 % from 0 to VCC - - 0.1 s Rpu pull-up resistance connected to VCC 8k 10 k 12 k Ipu pull-up current VOH = 0.9 VCC, C = 80 pF 20 12 4 mA TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 15 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface Table 7. Characteristics of IC …continued VDD = 3.3 V; Clock in = 10 MHz; GND = 0 V; Tamb = 25 C; unless otherwise specified Symbol Parameter Conditions Min Typ Max Unit Vhigh high voltage instantaneous voltage level: 1 pF cross capacitance load between pin I/O and CLK 0.7VCC - VCC + 0.3 V Vlow low voltage instantaneous voltage level: 1 pF cross capacitance load between pin I/O and CLK 0.3 - +0.4 V Data lines to the system; pins I/OC, AUX1C, AUX2C (Integrated 10k pull-up resistor to VDD)) VOL LOW-level output voltage IOL = 1 mA VOH HIGH-level output voltage No DC load IOH 40 A 0 - 0.3 V 0.9VDD - VDD + 0.1 V 0.75VDD - VDD+ 0.1 V - 0.3VDD V VDD + 0.3 V VIL LOW-level input voltage 0.3 VIH HIGH-level input voltage 0.7VDD Vhys hysteresis voltage on I/Ouc 0.05VDD - 0.25VDD V ILH HIGH-level leakage current VIH = VDD - - 10 A IIL LOW-level input current VIL = 0 - - 600 A Rpu pull-up resistance connected to VDD 8 11 14 k tr(i) input rise time from VIL max to VIH min - - 1.2 s tf(i) input fall time from VIL max to VIH min - - 1.2 s tr(o) output rise time CL 30 pF; 10 % to 90 % from 0 to VDD - - 0.1 s tf(o) output fall time CL 30 pF; 10% to 90% from 0 to VDD - - 0.1 s Ipu pull-up current VOH = 0.9 VDD, C = 30 pF 1 - - mA inactive state: osc(int)_Low 180 300 420 kHz active state: osc(int)_High 1.5 2.5 3.5 MHz inactive mode; no load 0 - 0.1 V inactive mode; Io = 1 mA 0 - 0.3 V Internal oscillator fosc(int) internal oscillator frequency Reset output to the card (RST) Vo output voltage Io output current inactive mode at grounded pin RST - - 1 mA td delay time between RSTIN and RST, RST enabled - - 200 ns VOL LOW-level output voltage IOL= 200 A 0 - 0.2 V IOL = 20 mA (current limit) VCC 0.4 - VCC V 0.9VCC - VCC V IOH = 20 mA (current limit) 0 - 0.4 V VOH HIGH-level output voltage IOH = 200 A tr rise time CL = 100 pF - - 0.1 s tf fall time CL = 100 pF - - 0.1 s Vhigh high voltage instantaneous voltage level: 1 pF cross capacitance load between pin RST and CLK 0.85VCC - VCC + 0.3 V TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 16 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface Table 7. Characteristics of IC …continued VDD = 3.3 V; Clock in = 10 MHz; GND = 0 V; Tamb = 25 C; unless otherwise specified Symbol Parameter Conditions Min Typ Max Unit Vlow low voltage instantaneous voltage level: 1 pF cross capacitance load between pin RST and CLK 0.3 - +0.32 V inactive mode; no load 0 - 0.1 V inactive mode; Io = 1 mA 0 - 0.3 V inactive mode - - 1 mA IOL = 200 A 0 - 0.3 V IOL = 70 mA (current limit) VCC 0.4 - VCC V 0.9VCC - VCC V 0 - 0.4 V Clock output to the card (CLK) Vo Io output voltage output current at grounded pin CLK VOL LOW-level output voltage VOH HIGH-level output voltage IOH = 200 A IOH = 70 mA (current limit) tr tf rise time fall time CL = 30 pF [2], fCLK = 5 MHz - - 16 ns CL = 30 pF [2], fCLK = 10 MHz - - 8 ns - - 16 ns - - 8 ns CL = 30 pF [2], fCLK = 5 MHz CL = 30 pF [2], fCLK =10 MHz fclk clock frequency on pin CLK operational 0 - 10 MHz duty cycle CL = 30 pF [2] 45 - 55 % SR slew rate rise and fall; CL = 30 pF 0.12 - - V/ns Vhigh high voltage instantaneous voltage level: 1 pF cross capacitance load between pin CLK and RST or CLK and I/O 0.85VCC - VCC + 0.3 V Vlow low voltage instantaneous voltage level: 1 pF cross capacitance load between pin RST and I/O 0.3 - +0.50 V 0.3 - +0.3VDD V Control inputs (pins CS, CMDVCCN, CLKDIV, RSTIN, TEST) [3] VIL LOW-level input voltage VIH HIGH-level input voltage 0.7VDD - VDD + 0.3 V Vhys hysteresis voltage on control input 0.05VDD - 0.25VDD V ILL LOW-level leakage current VIL = 0 - - 1 A ILH HIGH-level leakage current VIH = VDD - - 1 A 0.3 - 0.3VDD(INTF) V Card presence input (PRESN); PRESN has an integrated pull down resistor [3] VIL LOW-level input voltage VIH HIGH-level input voltage 0.7VDD - VDD + 0.3 V Vhys hysteresis voltage 0.05VDD - 0.1VDD V ILL LOW-level leakage current VIL = 0 - - 1 A ILH HIGH-level leakage current VIH = VDD - - 5 A TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 17 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface Table 7. Characteristics of IC …continued VDD = 3.3 V; Clock in = 10 MHz; GND = 0 V; Tamb = 25 C; unless otherwise specified Symbol Parameter Conditions Min Typ Max Unit - 0.3 V OFFN output (pin OFFN is an NMOS drain with a 10 k pull-up resistor to VDD) VOL LOW-level output voltage IOL = 2 mA 0 VOH HIGH-level output voltage IOH = 15 A 0.75VDD - - V Rpu pull-up resistance 8 10 13 k Protections and limitations Tsd shutdown temperature at die - 150 - C IOlim output current limit on pin I/O, AUX1 and AUX2 15 - +15 mA on pin CLK 70 - +70 mA on pin RST 20 - +20 mA on pin VCC 94 130 160 mA shutdown current on pin VCC 90 120 150 mA tact activation time see Figure 6 on page 9 182 - 554 s tdeact deactivation time see Figure 7 on page 10 35 - 250 s tact activation time time of the window for sending CLK to the card with CLKIN Isd Timing tdeb debounce time tact(start)= t3; see Figure 6 on page 9 182 256 426 s tact(end) = t5; see Figure 6 on page 9 237 332 554 s 3.04 4.26 7.11 ms on pin PRESN [1] To meet these specifications, VCC is decoupled to CGND using two ceramic multilayer capacitors of low ESR with both capacitors having a value of 220 nF. [2] The transition time and the duty factor definitions are shown in Figure 10 on page 18; d = t1/(t1+ t2) [3] PRESN and CMDVCCN are active LOW; RSTIN is active HIGH; for CLKDIV see Table 4. tr tf 90% 90% VOH (VOH + VOL) /2 10% 10% t1 VOL t2 fce666 Fig 10. Definition of output and input transition times TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 18 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 12. Application information AUX1UC AUX2UC VDD VDD 10 µF 100 nF PRESN I/O AUX2 AUX1 GND 1 16 2 15 3 14 4 5 TDA8037TT 13 12 6 11 7 10 8 9 c5 c1 c6 c2 c7 c3 c8 c4 I/OUC CLKIN MICRO CONTROLLER OFFN RSTIN CMDVCCN VCC RST 220 nF CLK 220 nF CARD CONNECTOR k1 k2 aaa-011381 Fig 11. Application diagram TDA8037TT TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 19 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface VDDhost VDD CLKDIV VDD 10 µF 100 nF 1 28 n.c. 2 27 n.c. TEST 3 26 4 25 n.c. VDD 5 24 6 23 n.c. 7 22 n.c. PRESN 8 9 20 n.c. 10 19 11 18 12 17 13 16 14 15 I/O AUX2 AUX1 GND TDA8037T 21 c5 c1 c6 c2 c7 c3 c8 c4 VDDhost AUX2UC AUX1UC I/OUC n.c. CLKIN OFFN MICRO CONTROLLER n.c. CS RSTIN CMDVCCN PORADJ R1 VCC RST 220 nF CLK R2 220 nF CARD CONNECTOR k1 k2 aaa-011382 Fig 12. Application diagram TDA8037T TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 20 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 13. Package outline SO28: plastic small outline package; 28 leads; body width 7.5 mm SOT136-1 D E A X c y HE v M A Z 28 15 Q A2 A (A 3) A1 pin 1 index θ Lp L 14 1 e bp 0 detail X w M 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y mm 2.65 0.3 0.1 2.45 2.25 0.25 0.49 0.36 0.32 0.23 18.1 17.7 7.6 7.4 1.27 10.65 10.00 1.4 1.1 0.4 1.1 1.0 0.25 0.25 0.1 0.01 0.019 0.013 0.014 0.009 0.71 0.69 0.30 0.29 0.05 0.419 0.043 0.055 0.394 0.016 inches 0.1 0.012 0.096 0.004 0.089 0.043 0.039 0.01 0.01 Z (1) 0.9 0.4 0.035 0.004 0.016 θ 8o o 0 Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT136-1 075E06 MS-013 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Fig 13. Package outline SOT136-1 TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 21 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 E D A X c y HE v M A Z 9 16 Q (A 3) A2 A A1 pin 1 index θ Lp L 1 8 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) θ mm 1.1 0.15 0.05 0.95 0.80 0.25 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 1 0.75 0.50 0.4 0.3 0.2 0.13 0.1 0.40 0.06 8o o 0 Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC SOT403-1 JEDEC JEITA MO-153 EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 14. Package outline SOT403-1 TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 22 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 14. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 14.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 14.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 14.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 23 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 14.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 15) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 8 and 9 Table 8. SnPb eutectic process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 9. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 15. TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 24 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 15. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. 15. Abbreviations Table 10. Abbreviations Acronym Description ESD ElectroStatic Discharge 16. Revision history Table 11. Revision history Document ID Release date Data sheet status Change notice Supersedes TDA8037 v.1.1 20141117 Product data sheet - TDA8037 v.1 - - Modifications: TDA8037 v.1 TDA8037 Product data sheet • Table 3 “Pin description”: updated 20141007 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 25 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 17. Legal information 17.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 17.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 17.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. TDA8037 Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 26 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 17.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 18. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 27 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 19. Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Quick reference data . . . . . . . . . . . . . . . . . . . . .2 Ordering information . . . . . . . . . . . . . . . . . . . . .2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5 Clock configuration (SO28 only) . . . . . . . . . . . . .7 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . .13 Thermal characteristics . . . . . . . . . . . . . . . . . .13 Table 7. Table 8. Table 9. Table 10. Table 11. Characteristics of IC . . . . . . . . . . . . . . . . . . . . 14 SnPb eutectic process (from J-STD-020D) . . . 24 Lead-free process (from J-STD-020D) . . . . . . 24 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 25 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 25 20. Figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Pin configuration TSSOP16 . . . . . . . . . . . . . . . . . .4 Pin configuration SO28 . . . . . . . . . . . . . . . . . . . . .4 Block voltage supervisor . . . . . . . . . . . . . . . . . . . .6 Voltage supervisor . . . . . . . . . . . . . . . . . . . . . . . . .7 Activation sequence at t3 . . . . . . . . . . . . . . . . . . .9 Deactivation sequence . . . . . . . . . . . . . . . . . . . .10 Emergency deactivation sequence (card extraction) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Behavior of OFFN, CMDVCCN, PRESN and VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Definition of output and input transition times . . .18 Application diagram TDA8037TT. . . . . . . . . . . . .19 Application diagram TDA8037T . . . . . . . . . . . . . .20 Package outline SOT136-1 . . . . . . . . . . . . . . . . .21 Package outline SOT403-1 . . . . . . . . . . . . . . . . .22 Temperature profiles for large and small components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 TDA8037 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.1 — 17 November 2014 © NXP Semiconductors N.V. 2014. All rights reserved. 28 of 29 TDA8037 NXP Semiconductors Low power 3V smart card interface 21. Contents 1 2 2.1 2.2 2.2.1 3 4 5 6 7 7.1 7.2 7.3 8 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 8.10 9 10 11 12 13 14 14.1 14.2 14.3 14.4 15 16 17 17.1 17.2 17.3 17.4 18 19 20 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Protection of the contact smart card . . . . . . . . . 1 Easy integration into your contact reader . . . . . 1 Other. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 6 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Voltage supervisor . . . . . . . . . . . . . . . . . . . . . . 6 Clock circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . 7 I/O circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 CS control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Shutdown mode . . . . . . . . . . . . . . . . . . . . . . . . 8 Activation sequence . . . . . . . . . . . . . . . . . . . . . 9 Deactivation sequence . . . . . . . . . . . . . . . . . . 10 VCC regulator . . . . . . . . . . . . . . . . . . . . . . . . . 10 Fault detection . . . . . . . . . . . . . . . . . . . . . . . . 11 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 13 Thermal characteristics . . . . . . . . . . . . . . . . . 13 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 14 Application information. . . . . . . . . . . . . . . . . . 19 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 21 Soldering of SMD packages . . . . . . . . . . . . . . 23 Introduction to soldering . . . . . . . . . . . . . . . . . 23 Wave and reflow soldering . . . . . . . . . . . . . . . 23 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 23 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 24 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 25 Legal information. . . . . . . . . . . . . . . . . . . . . . . 26 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 26 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Contact information. . . . . . . . . . . . . . . . . . . . . 27 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 21 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP Semiconductors N.V. 2014. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 17 November 2014 Document identifier: TDA8037