MN102H85K Type MN102H85K ROM (×× 16-bit) 256 K RAM (×× 16-bit) 8K Package (Conventional Package) SDIP064-P-0750C *Lead-free (SDIP064-P-0750) Minimum Instruction Execution Time 83 ns (at 3.0 V to 3.6 V, 12 MHz) Interrupts External (6 lines) Internal (30 lines) : Timer × 11, A/D × 1, Undefined command × 1, RESET × 1, OSD × 2, Serial × 4, I2C × 1, Caption × 4, Remote control × 1, Address coincidence × 4 Timer Counter 8-bit timer × 4 16-bit timer × 2 Watchdog timer: 17-bit × 1 Serial Interface I2C × 1: for multimaster mode, bus line (output) has 2 systems Sync serial / I2C (master) / UART × 2 • Built-in sync separator × 2 Caption I/O Pins I/O 50 • Common use A/D Inputs 8-bit × 12-ch. (with S/H) D/A Outputs 4-bit × 4-ch. (analog R, G, B, YM output) PWM 8-bit × 7-ch. Special Ports Remote control reception CRTC 3-layer display (graphics, characters, splits) Notes Remote control input discriminant circuit built-in Electrical Characteristics D/A characteristics Limit Parameter Symbol Condition Unit min typ max 5.0 5.5 mA 1.1 V D/Afull-scaleoutputcurrent IFS RL = 200 Ω, VREF = 1.2 V, RIREF = 1.2 kΩ 4.5 D/A output voltage setting range VO RL = 200 Ω, VREF = 1.2 V, RIREF = 1.2 kΩ 0.9 D/A non-linear error NLE RL = 200 Ω, VREF = 1.2 V, RIREF = 1.2 kΩ ± 0.5 LSB D/A differential non-linear error DNLE RL = 200 Ω, VREF = 1.2 V, RIREF = 1.2 kΩ ± 0.5 LSB ±5 % D/A channel interval error IFS VREF = 1.2 V, RIREF = 1.2 kΩ, Error from 4-channel average IFS (Ta = 25°C , VDD = AVDD = 3.3 V , VSS = 0 V , fosc = 4 MHz) 1 MAE00014DEM MN102H85K Pin Assignment ( P00,RMIN,IRQ0 1 64 VSS *1 P01,SDA1 2 63 OSC2 *1 P02,SCL1 3 62 OSC1 P03,ADIN0 4 61 VDD P04,ADIN1 5 60 P61,SCL0 *1 P05,ADIN2 6 59 P60,SDA0 *1 P06,ADIN3 7 58 P57,SBT0 P07,ADIN4 8 57 P56,SBI0,SBD0 P10,ADIN5,IRQ1 9 56 P55,SBO0 P11,ADIN6,IRQ2 10 55 P54,IRQ5,/VSYNC P12,ADIN7,IRQ3 11 54 P53,/RST P13,ADIN8,WDOUT 12 53 P52,IRQ4,VI0 P14,ADIN9,STOP 13 52 /TEST P15,ADIN10,PWM0 14 51 P51,YS P16,ADIN11,PWM1 15 50 P50,SYSCLK P17,PWM2 16 49 P47,/HSYNC P20,PWM3 17 48 P46,OSDXI P21,PWM4 18 47 P45,OSDXO P22,PWM5 19 46 P44,TM5IC,HI1 *1 P23,PWM6 20 45 P43,TM5IOB,HI0 *1 P24,TM4IC,SBT1 21 44 P42,TM5IOA *1 P25,TM4IOB,SBI1,SBD1 22 43 P41,TM1IO *1 P26,TM4IOA,SBO1 23 42 VCOI P27,TM0IO 24 41 PDO *2 VDD(VPP) 25 40 P40,DAYMOUT,YM P30,CLH 26 39 P37,DABOUT,B VREFHS 27 38 P36,DAGOUT,G P31,CVBS0 28 37 P35,DAROUT,R VSS 29 36 VREF,P34 P32,CVBS1 30 35 IREF VREFLS 31 34 COMP P33,CLL 32 33 AVDD MN102H85K ) : Conventional Package SDIP064-P-0750C *Lead-free (SDIP064-P-0750) *1: 5 V dielectric Nch open drain output pin *2 : MN102H85K (VDD), MN102HF85K (VPP) Support Tool In-circuit Emulator PX-ICE102H85-SDIP064-P-0750 Flash Memory Built-in Type Type MN102HF85K ROM (× 16-bit) 256 K RAM (× 16-bit) 8K Minimum instruction execution time 83 ns (at 3.0 V to 3.6 V, 12 MHz) Package SDIP064-P-0750C *Lead-free (Conventional Package) (SDIP064-P-0750 ) MAE00014DEM 2 Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2002 JUL