MN103S65G Type MN103S65G Internal ROM 128 K-byte Internal RAM 4 K-byte SRAM Package LQFP080-P-1414A *Lead-free Minimum Instruction Execution Time 25 ns (at 4.3 V to 5.5 V, 10 MHz internal regulator used) 25 ns (at 3.0 V to 3.6 V, 10 MHz) *at internal 4 times oscillation used) Interrupts • 9 external interrupts • 42 internal interrupts (watch dog timer, timer, serial I/F, PWM, A/D, system error) Timer Counter Eight 8-bit timers Interval timer, Event counter, Cascading Four 16-bit timers Interval timer, Event counter, PWM output, Double buffer Watch dog timer Serial Interface I/O Pins UART (full duplex) / synchronous interfaces selective: 3 I/O 50 exclusive: 2, selective: 48 Input 10 selective: 10 A/D Inputs 10-bits, 2 inputs: 2, 6 inputs: 1 Minimum conversion time 1.5us PWM 3-phase PWM output 16-bit counter, triangular waveform or jigsaw waveform dead time setup, Double buffer Electrical Characteristics T.B.D. MAF00010AEM MN103S65G 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 P63/PWM11 P62/PWM10 P61 P60 P57/NPWM02 P56/PWM02 P55/NPWM01 P54/PWM01 P53/NPWM00 P52/PWM00 VDD P51/TM10BO VSS P50/TM10AO VDD2 VPP P47/TM10BI P46/TM10AI P45/TM9BO P44/TM9AO Pin Assignment 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 MN103S65G P43/TM9BI P42/TM9AI P41/TM8BIO P40/TM8AIO P37/TM7IO P36/TM6IO P35/TM5IO VDD P34/TM4IO VSS P33/TM3IO P32/TM2IO P31/TM1IO P30/TM0IO P27/SBI0 P26/SBT0 P25/SBO0 P24/SBI1 P23/SBT1 P22/SBO1 TEST1 TEST2 TEST3 OSCO OSCI VSS PVSS PVDD VDD2 VDD LON P07/NRST P10/IRQ04 P11/IRQ05 P12/IRQ06 P13/IRQ07 P14/IRQ08 P17/SBO2 P20/SBT2 P21/SBI2 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 P64/PWM12 P65/PWM13 P66/PWM14 P67/PWM15 P74/IRQ00 P75/IRQ01 P76/IRQ02 P77/IRQ03 P80/ADIN00 P81/ADIN01 VSS P82/ADIN10 VDD P83/ADIN11 P84/ADIN20 P85/ADIN21 P86/ADIN22 P87/ADIN23 P90/ADIN24 P91/ADIN25 LQFP080-P-1414A *Lead-free Support Tool In-circuit Emulator PX-ICE-103S52 On board Debugger PX-ODB103S-DO Flash Memory Built-in Type Type MN103SF65G ROM 128 K-byte RAM 4 K-byte SRAM Minimum instruction execution time 25 ns (at 4.3 V to 5.5 V, 10 MHz internal regulator used) 25 ns (at 3.0 V to 3.6 V, 10 MHz) Package MAF00010AEM LQFP080-P-1414A *Lead-free Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technical information described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2003 SEP