CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead New! ●Super low ESR, high ripple current capability from PSE series (φ6.3×8L to φ5×8L) ●Longer life (5,000 hours at 105℃) ●ESR after endurance is specied within the initial spec ●RoHS Compliant ●Halogen Free PSK ●Downsized Downsized PSE ◆SPECIFICATIONS Items Characteristics Category Temperature Range -55 to +105℃ Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current*Note Dissipation Factor (tanδ) 2.5Vdc ±20% (M) Rated voltage(V)×1.15 500ѥA max. Low Temperature Characteristics (Max.Impedance Ratio) Z(-25℃)/Z(+20℃)≦1.15 Z(-55℃)/Z(+20℃)≦1.25 Endurance Bias Humidity Test Surge Voltage Test Failure Rate (at 20℃, 120Hz) (at 105℃) (at 20℃ after 2 minutes) 0.10 max. (at 20℃, 120Hz) (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 5,000 hours at 105℃. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦The initial specified value Leakage current ≦The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦The initial specified value Leakage current ≦The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦The initial specified value Leakage current ≦The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃. ◆DIMENSIONS [mm] Code : E F±0.5 ● Terminal φD' φd Coated Case L' 15min. Size code φD φd F φD' L' E08 5.0 0.45 2.0 φD+0.5max. L+1.0max. ◆MARKING EX) 2.5V560ѥF K6D6 560 2.5V 4min. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. (1/2) CAT. No. E1001L CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead New! ◆PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A PSK 2 R 5 E AA 5 6 1 M E 0 8 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 560μF:561) Lead forming.Taping code Terminal code Voltage code Series code Category Please refer to "Product code guide (conductive polymer type)" ◆STANDARD RATINGS WV(Vdc) Cap(µF) 2.5 220 330 470 560 φD×L (mm) Case size ESR (mΩ max./20℃, 100k to 300kHz) Rated ripple current (mArms/105℃, 100kHz) 5×8 5×8 5×8 5×8 7 7 7 7 4,350 4,350 4,350 4,350 Part No. APSK2R5E□□221ME08S APSK2R5E□□331ME08S APSK2R5E□□471ME08S APSK2R5E□□561ME08S □□ : Enter the appropriate lead forming or taping code. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. (2/2) CAT. No. E1001L