LT8613 42V, 6A Synchronous Step-Down Regulator with Current Sense and 3µA Quiescent Current Description Features Rail-to-Rail Current Sense Amplifier with Monitor n Wide Input Voltage Range: 3.4V to 42V n Ultralow Quiescent Current Burst Mode® Operation: 3μA IQ Regulating 12VIN to 3.3VOUT Output Ripple < 10mVP-P n High Efficiency Synchronous Operation: 95% Efficiency at 3A, 5VOUT from 12VIN 94% Efficiency at 3A, 3.3VOUT from 12VIN n Fast Minimum Switch-On Time: 40ns n Low Dropout Under All Conditions: 250mV at 3A n Allows Use Of Small Inductors n Low EMI n Adjustable and Synchronizable: 200kHz to 2.2MHz n Current Mode Operation n Accurate 1V Enable Pin Threshold n Internal Compensation n Output Soft-Start and Tracking n Small Thermally Enhanced 3mm × 6mm 28-Lead QFN Package n Applications Automotive and Industrial Supplies General Purpose Step-Down n CCCV Power Supplies n The LT®8613 is a compact, high efficiency, high speed synchronous monolithic step-down switching regulator that consumes only 3µA of quiescent current. Top and bottom power switches are included with all necessary circuitry to minimize the need for external components. The built-in current sense amplifier with monitor and control pins allows accurate input or output current regulation and limiting. Low ripple Burst Mode operation enables high efficiency down to very low output currents while keeping the output ripple below 10mVP-P. A SYNC pin allows synchronization to an external clock. Internal compensation with peak current mode topology allows the use of small inductors and results in fast transient response and good loop stability. The EN/UV pin has an accurate 1V threshold and can be used to program VIN undervoltage lockout or to shut down the LT8613 reducing the input supply current to 1µA. A capacitor on the TR/SS pin programs the output voltage ramp rate during start-up. The PG flag signals when VOUT is within ±9% of the programmed output voltage as well as fault conditions. The LT8613 is available in a small 28-lead 3mm × 6mm QFN package with exposed pad for low thermal resistance. L, LT, LTC, LTM, Burst Mode, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. n Typical Application Efficiency at 5VOUT 5V Step-Down Converter with 6A Output Current Limit 10µF ON OFF VIN BST EN/UV SYNC IMON 3.9µH LT8613 ICTRL 10µF 1µF 60.4k fSW = 700kHz L: EPCOS B82559 PGND 1µF VOUT 5V 6A ISP ISN PG TR/SS RT 8mΩ SW BIAS INTVCC GND FB VIN = 12V 95 0.1µF 10pF VIN = 24V 90 EFFICIENCY (%) VIN 5.8V TO 42V 100 85 80 75 70 65 1M 243k 100µF 60 fSW = 700kHz L = 3.9µH 0 1 4 3 2 LOAD CURRENT (A) 5 6 8613 TA01a 8613 TA01b 8613f For more information www.linear.com/LT8613 1 LT8613 Pin Configuration VIN, EN/UV, PG, ISP, ISN............................................42V BIAS...........................................................................25V BST Pin Above SW Pin................................................4V FB, TR/SS, RT, INTVCC, IMON, ICTRL..........................4V SYNC Voltage ..............................................................6V Operating Junction Temperature Range (Note 2) LT8613E.................................................. –40 to 125°C LT8613I................................................... –40 to 125°C Storage Temperature Range.......................–65 to 150°C ISP ICTRL TOP VIEW ISN (Note 1) IMON Absolute Maximum Ratings 28 27 26 25 SYNC 1 24 FB TR/SS 2 23 PG RT 3 22 BIAS EN/UV 4 21 INTVCC VIN 5 20 BST 29 GND VIN 6 19 SW VIN 7 18 SW PGND 8 17 SW PGND 9 16 SW PGND 10 15 SW GND GND GND GND 11 12 13 14 UDE PACKAGE 28-LEAD (3mm × 6mm) PLASTIC QFN θJA = 40°C/W, θJC(PAD) = 5°C/W EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT8613EUDE#PBF LT8613EUDE#TRPBF LGHX 28-Lead (3mm × 6mm) Plastic QFN –40°C to 125°C LT8613IUDE#PBF LT8613IUDE#TRPBF LGHX 28-Lead (3mm × 6mm) Plastic QFN –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. PARAMETER Minimum Input Voltage VIN Quiescent Current CONDITIONS MIN l VEN/UV = 0V, VSYNC = 0V l VEN/UV = 2V, Not Switching, VSYNC = 0V l VIN Current in Regulation Feedback Reference Voltage Feedback Voltage Line Regulation Feedback Pin Input Current BIAS Pin Current Consumption 2 VEN/UV = 2V, Not Switching, VSYNC = 2V VOUT = 0.97V, VIN = 6V, Output Load = 100µA VOUT = 0.97V, VIN = 6V, Output Load = 1mA VIN = 12V, ILOAD = 500mA VIN = 12V, ILOAD = 500mA VIN = 4.0V to 25V, ILOAD = 0.5A VFB = 1V VBIAS = 3.3V, ILOAD = 2A, 2MHz l l l 0.964 0.958 l –20 TYP 2.9 1.0 1.0 1.7 1.7 0.3 24 230 0.970 0.970 0.004 0.5 14 MAX 3.4 5 20 6 20 0.6 60 370 0.976 0.982 0.025 20 UNITS V µA µA µA µA mA µA µA V V %/V nA mA 8613f For more information www.linear.com/LT8613 LT8613 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. PARAMETER Minimum On-Time Minimum Off-Time Oscillator Frequency Top Power NMOS On-Resistance Top Power NMOS Current Limit Bottom Power NMOS On-Resistance Valley Current Limit SW Leakage Current EN/UV Pin Threshold EN/UV Pin Hysteresis EN/UV Pin Current PG Upper Threshold Offset from VFB PG Lower Threshold Offset from VFB PG Hysteresis PG Leakage PG Pull-Down Resistance SYNC Threshold SYNC Pin Current TR/SS Source Current TR/SS Pull-Down Resistance Current Sense Voltage (VISP-ISN) IMON Monitor Pin Voltage CONDITIONS ILOAD = 2A, SYNC = 0V ILOAD = 2A, SYNC = 3.3V l l l MIN 20 20 50 180 665 1.85 l 7.5 l 6 –10 0.94 l l RT = 221k, ILOAD = 1.5A RT = 60.4k, ILOAD = 1.5A RT = 18.2k, ILOAD = 1.5A ISW = 1A VINTVCC = 3.4V, ISW = 1A VINTVCC = 3.4V VIN = 42V, VSW = 0V, 42V EN/UV Rising l VEN/UV = 2V VFB Falling VFB Rising l l VPG = 3.3V VPG = 0.1V SYNC Falling SYNC Rising VSYNC = 2V –20 6.5 –6.5 TYP 40 35 85 210 700 2.00 65 9.7 29 10 0.1 1.0 40 1 9.0 –9.0 1.3 –40 l l Fault Condition, TR/SS = 0.1V VICTRL = 1.5V, VISN = 3.3V VICTRL = 1.5V, VISN = 0V VICTRL = 800mV, VISN = 3.3V VICTRL = 800mV, VISN = 0V VICTRL = 200mV, VISN = 3.3V VICTRL = 200mV, VISN = 0V VISP-ISN = 50mV, VISN = 3.3V VISP-ISN = 50mV, VISN = 0V VISP-ISN = 10mV, VISN = 3.3V VISP-ISN = 10mV, VISN = 0V l l l l l l l l l l ISP, ISN Pin Bias Current l Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT8613E is guaranteed to meet performance specifications from 0°C to 125°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization, and correlation with statistical process controls. The LT8613I is guaranteed over the full –40°C to 125°C operating junction 0.7 1.0 –100 1.4 48 46 38 37 5 4 0.960 0.890 130 110 –20 680 1.0 1.3 2.1 230 50 50.5 41 42 10 10.5 1.00 0.99 220 205 MAX 60 55 120 240 735 2.15 12.0 12 10 1.06 20 11.5 –11.5 40 2000 1.4 1.55 100 2.7 52 56 46 47 15 17 1.040 1.09 320 300 20 UNITS ns ns ns kHz kHz MHz mΩ A mΩ A µA V mV nA % % % nA Ω V V nA µA Ω mV mV mV mV mV mV V V mV mV µA temperature range. High junction temperatures degrade operating lifetimes. Operating lifetime is derated at junction temperatures greater than 125°C. Note 3: This IC includes overtemperature protection that is intended to protect the device during overload conditions. Junction temperature will exceed 150°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature will reduce lifetime. 8613f For more information www.linear.com/LT8613 3 LT8613 Typical Performance Characteristics Efficiency at 3.3VOUT Efficiency at 5VOUT VIN = 12V 95 VIN = 24V EFFICIENCY (%) EFFICIENCY (%) VIN = 12V 80 75 VIN = 24V 85 80 75 70 65 fSW = 700kHz L = 3.9µH, EPCOS B82559 0 4 3 2 LOAD CURRENT (A) 1 5 60 6 60 0 1 4 3 2 LOAD CURRENT (A) 5 fSW = 700kHz L = 3.9µH 40 0.1 1 10 0.00001 0.0001 0.001 0.01 LOAD CURRENT (A) 6 8613 G02 Efficiency at 3.3VOUT 8613 G03 Efficiency vs Frequency Reference Voltage 0.985 100 100 0.982 VIN = 12V VIN = 24V 70 60 50 40 0.1 0.00001 0.0001 0.001 0.01 LOAD CURRENT (A) 1 90 85 80 VOUT = 3.3V VIN = 12V L = 3.9µH LOAD = 2A 75 fSW = 700kHz L = 3.9µH 70 10 REFERENCE VOLTAGE (V) 80 95 EFFICIENCY (%) 90 EFFICIENCY (%) VIN = 24V 70 50 fSW = 700kHz L = 3.9µH, EPCOS B82559 8613 G01 0 500 EN/UV Pin Thresholds 1500 1000 FREQUENCY (kHz) 2000 0.98 EN/UV FALLING 0.96 0 0.970 0.967 0.964 0.961 0.955 –55 2500 25 50 75 100 125 150 TEMPERATURE (°C) 8613 G07 –25 65 35 5 95 TEMPERATURE (°C) 125 Line Regulation 0.5 0.10 0.4 0.08 0.3 0.06 0.2 0.1 0 –0.1 VOUT = 5V LOAD = 1A 0.04 0.02 0 –0.02 –0.2 –0.04 –0.3 –0.06 –0.4 –0.08 –0.5 155 8613 G06 CHANGE IN VOUT (%) LOAD REGULATION (%) EN/UV RISING 0.99 0.95 –55 –25 0.973 Load Regulation 1.00 0.97 0.976 8613 G05 1.02 1.01 0.979 0.958 8613 G04 EN/UV THRESHOLD (V) 80 70 65 4 VIN = 12V 90 90 85 60 100 95 90 Efficiency at 5VOUT 100 EFFICIENCY (%) 100 0 1 4 2 3 OUTPUT LOAD (A) 5 6 8613 G08 –0.10 0 10 30 20 INPUT VOLTAGE (V) 40 50 8613 G09 8613f For more information www.linear.com/LT8613 LT8613 Typical Performance Characteristics No Load Supply Current Top FET Current Limit vs Duty Cycle 3.6 TOP FET CURRENT LIMIT (A) INPUT CURRENT (µA) 3.4 3.2 3.0 2.8 2.6 2.4 2.2 2.0 10 30 20 INPUT VOLTAGE (V) 40 11 9 10 8 7 6 5 VOUT = 5V 0 4 50 0 20 60 40 DUTY CYCLE (%) 80 VSYNC = 3.3V 20 5 0.5 90 85 80 75 70 60 –50 –25 6 800 0 690 680 660 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 8613 G16 1 3 4 2 LOAD CURRENT (A) 5 60 50 600 500 400 300 200 0 6 Minimum Load to Full Frequency (SYNC Hi) Burst Frequency 40 30 20 10 100 670 0 8613 G15 MINIMUM LOAD (mA) SWITCH FREQUENCY (kHz) SWITCHING FREQUENCY (kHz) 730 700 0.2 0 25 50 75 100 125 150 TEMPERATURE (°C) VIN = 12V 700 VOUT = 5V L = 3.9µH RT = 60.4k 710 0.3 8613 G14 Switching Frequency 720 0.4 0.1 8613 G13 740 25 50 75 100 125 150 TEMPERATURE (°C) Dropout Voltage 65 4 2 3 LOAD CURRENT (A) 0 0.6 DROPOUT VOLTAGE (V) MINIMUM OFF-TIME (ns) MINIMUM ON-TIME (ns) 30 1 6 8613 G12 95 40 VSYNC = 0V 70% DUTY CYCLE 7 4 –50 –25 100 100 0 8 Minimum Off-Time Minimum On-Time 25 9 8613 G11 45 35 15% DUTY CYCLE 5 8613 G10 15 Top FET Current Limit 10 CURRENT LIMIT (A) 3.8 0 100 200 300 400 LOAD CURRENT (mA) 500 8613 G17 0 0 10 20 30 INPUT VOLTAGE (V) 40 50 8613 G18 8613f For more information www.linear.com/LT8613 5 LT8613 Typical Performance Characteristics Frequency Foldback VOUT = 3.3V VIN = 12V VSYNC = 0V RT = 60.4k 700 SWITCHING FREQUENCY (kHz) Soft-Start Tracking 2.4 500 400 300 0.8 0.6 0.4 200 0.2 100 0 0 0.2 0.4 0.6 FB VOLTAGE (V) 0.8 0 1 2.2 2.1 2.0 1.9 1.8 1.7 0 0.2 1.0 0.4 0.6 0.8 TR/SS VOLTAGE (V) 8613 G19 1.2 1.6 –50 –25 1.4 200 FB FALLING 9.5 –8.5 –9.0 FB RISING –9.5 FB FALLING –10.0 9.0 –10.5 8.5 8.0 7.5 7.0 –55 –25 65 35 5 95 TEMPERATURE (°C) 125 155 150 125 100 75 50 –11.5 25 –12.0 –55 –25 65 35 5 95 TEMPERATURE (°C) 125 155 0 0.2 VIN UVLO 2.2 8613 G24 Switching Waveforms Switching Waveforms IL 1A/DIV IL 1A/DIV 3.2 0.6 1.4 1.8 1 SWITCHING FREQUENCY (MHz) 8613 G23 3.4 INPUT VOLTAGE (V) 175 –11.0 8613 G22 3.6 RT PIN RESISTOR (kΩ) 225 –8.0 PG THRESHOLD OFFSET FROM VREF (%) 250 –7.5 PG THRESHOLD OFFSET FROM VREF (%) –7.0 11.5 10.0 155 RT Programmed Switching Frequency PG Low Thresholds FB RISING 125 8613 G21 12.0 10.5 95 65 35 TEMPERATURE (°C) 5 8613 G20 PG High Thresholds 11.0 VSS = 0.5V 2.3 1.0 FB VOLTAGE (V) 600 Soft-Start Current 1.2 SS PIN CURRENT (µA) 800 3.0 VSW 5V/DIV 2.8 2.6 5µs/DIV 2.4 8613 G26 12VIN TO 5VOUT AT 20mA; FRONT PAGE APP VSYNC = 0V 2.2 2.0 –55 –25 VSW 5V/DIV 95 65 35 TEMPERATURE (°C) 5 125 1µs/DIV 8613 G27 12VIN TO 5VOUT AT 2A FRONT PAGE APP 155 8613 G25 6 8613f For more information www.linear.com/LT8613 LT8613 Typical Performance Characteristics Switching Waveforms Transient Response IL 1A/DIV VSW 10V/DIV 500ns/DIV ILOAD 1A/DIV ILOAD 1A/DIV VOUT 200mV/DIV VOUT 200mV/DIV 8613 G28 50µs/DIV 36VIN TO 5VOUT AT 2A FRONT PAGE APP VIN 2V/DIV VOUT 200mV/DIV VOUT 2V/DIV 8613 G31 VIN Start-Up Dropout Performance VIN 2V/DIV VOUT 100ms/DIV 2.5Ω LOAD (2A IN REGULATION) 8613 G30 1A TO 2A TRANSIENT 12VIN TO 5VOUT COUT = 2×47µF FRONT PAGE APP Start-Up Dropout Performance ILOAD 1A/DIV 1A TO 3A TRANSIENT 12VIN TO 5VOUT COUT = 2×47µF FRONT PAGE APP 20µs/DIV 8613 G29 0.1A TO 1.1A TRANSIENT 12VIN TO 5VOUT COUT = 2×47µF FRONT PAGE APP Transient Response 20µs/DIV Transient Response VOUT 2V/DIV 8613 G32 VIN VOUT 100ms/DIV 20Ω LOAD (250mA IN REGULATION) 8613 G33 8613f For more information www.linear.com/LT8613 7 LT8613 Typical Performance Characteristics ICTRL Voltage VISP-VISN Sense Voltage 40 30 20 10 0 VISP-VISN Sense Voltage 55 55 54 54 53 53 52 MAX VISP-VISN VOLTAGE (mV) 50 MAX VISP-VISN VOLTAGE (mV) MAX VISP-VISN VOLTAGE (mV) 60 VISP = 0V 51 50 VISP = 3V 49 48 47 0 500 1000 1500 ICTRL VOLTAGE (mV) 0 50 49 48 47 45 25 50 75 100 125 150 TEMPERATURE (°C) IMON Voltage 0.5 2 1.5 1 2.5 3 ISP-ISN COMMON MODE (V) 1000 1000 800 800 3.5 8613 G42 IMON Voltage 1200 VSYNC = 3.3V 0 8613 G41 8613 G40 1200 51 46 46 –50 –25 2000 52 IMON Voltage 1.10 VSYNC = 0V VISP-VISN = 50mV 600 IMON VOLTAGE (V) VIMON (mV) VIMON (mV) 1.05 600 400 400 200 200 1.00 0.95 0 0 10 20 30 VISP-VISN (mV) 40 50 8613 G43 8 0 0 10 20 30 VISP-VISN (mV) 50 40 8613 G44 0.90 0 0.5 2.5 3 1 1.5 2 ISP-ISN COMMON MODE (V) 3.5 8613 G45 8613f For more information www.linear.com/LT8613 LT8613 Pin Functions SYNC (Pin 1): External Clock Synchronization Input. Ground this pin for low ripple Burst Mode operation at low output loads. Tie to a clock source for synchronization to an external frequency. Apply a DC voltage of 3V or higher or tie to INTVCC for pulse-skipping mode. When in pulseskipping mode, the IQ will increase to several hundred µA. When SYNC is DC high or synchronized, frequency foldback will be disabled. Do not float this pin. GND (Pins 11, 12, 13, 14): It is recommended that these be connected to GND so that the exposed pad GND can be run to the top level GND copper to enhance thermal performance. TR/SS (Pin 2): Output Tracking and Soft-Start Pin. This pin allows user control of output voltage ramp rate during start-up. A TR/SS voltage below 0.97V forces the LT8613 to regulate the FB pin to equal the TR/SS pin voltage. When TR/SS is above 0.97V, the tracking function is disabled and the internal reference resumes control of the error amplifier. An internal 2.2μA pull-up current from INTVCC on this pin allows a capacitor to program output voltage slew rate. This pin is pulled to ground with an internal 230Ω MOSFET during shutdown and fault conditions; use a series resistor if driving from a low impedance output. This pin may be left floating if the tracking function is not needed. BST (Pin 20): This pin is used to provide a drive voltage, higher than the input voltage, to the topside power switch. Place a 0.1µF boost capacitor as close as possible to the IC. RT (Pin 3): A resistor is tied between RT and ground to set the switching frequency. EN/UV (Pin 4): The LT8613 is shut down when this pin is low and active when this pin is high. The hysteretic threshold voltage is 1.00V going up and 0.96V going down. Tie to VIN if the shutdown feature is not used. An external resistor divider from VIN can be used to program a VIN threshold below which the LT8613 will shut down. VIN (Pins 5, 6, 7): The VIN pins supply current to the LT8613 internal circuitry and to the internal topside power switch. These pins must be tied together and be locally bypassed. Be sure to place the positive terminal of the input capacitor as close as possible to the VIN pins, and the negative capacitor terminal as close as possible to the PGND pins. PGND (Pins 8, 9, 10): Power Switch Ground. These pins are the return path of the internal bottom-side power switch and must be tied together. Place the negative terminal of the input capacitor as close to the PGND pins as possible. SW (Pins 15–19): The SW pins are the outputs of the internal power switches. Tie these pins together and connect them to the inductor and boost capacitor. This node should be kept small on the PCB for good performance. INTVCC (Pin 21): Internal 3.4V Regulator Bypass Pin. The internal power drivers and control circuits are powered from this voltage. INTVCC maximum output current is 20mA. Do not load the INTVCC pin with external circuitry. INTVCC current will be supplied from BIAS if VBIAS > 3.1V, otherwise current will be drawn from VIN. Voltage on INTVCC will vary between 2.8V and 3.4V when VBIAS is between 3.0V and 3.6V. Decouple this pin to power ground with at least a 1μF low ESR ceramic capacitor placed close to the IC. BIAS (Pin 22): The internal regulator will draw current from BIAS instead of VIN when BIAS is tied to a voltage higher than 3.1V. For output voltages of 3.3V and above this pin should be tied to VOUT. If this pin is tied to a supply other than VOUT use a 1µF local bypass capacitor on this pin. PG (Pin 23): The PG pin is the open-drain output of an internal comparator. PG remains low until the FB pin is within ±9% of the final regulation voltage, and there are no fault conditions. PG is valid when VIN is above 3.4V, regardless of EN/UV pin state. FB (Pin 24): The LT8613 regulates the FB pin to 0.970V. Connect the feedback resistor divider tap to this pin. Also, connect a phase lead capacitor between FB and VOUT. Typically, this capacitor is 4.7pF to 10pF. ISP (Pin 25): Current Sense (+) Pin. This is the noninverting input to the current sense amplifier. 8613f For more information www.linear.com/LT8613 9 LT8613 Pin Functions ISN (Pin 26): Current Sense (–) Pin. This is the inverting input to the current sense amplifier. IMON (Pin 27): Proportional-to-Current Monitor Output. This pin sources a voltage 20 times the voltage between the ISP and ISN pins such that: VIMON = 20 • (VISP-VISN). IMON can source 200µA and sink 10µA. Float IMON if unused. ICTRL (Pin 28): Current Adjustment Pin. ICTRL adjusts the maximum ISP-ISN drop before the LT8613 reduces output current. Connect directly to INTVCC or float for full-scale ISP-ISN threshold of 50mV or apply values between GND and 1V to modulate current limit. There is an internal 1.4µA pull-up current on this pin. Float or tie to INTVCC when unused. GND (Exposed Pad Pin 29): Ground. The exposed pad must be connected to the negative terminal of the input capacitor and soldered to the PCB in order to lower the thermal resistance. Block Diagram VIN CIN R3 OPT EN/UV R4 OPT PG 1V + – SHDN ±9% R2 CSS (OPT) RT R1 FB TR/SS BIAS 3.4V REG SLOPE COMP ERROR AMP + + – VOUT C1 – + INTERNAL 0.97V REF INTVCC CVCC OSCILLATOR 200kHz TO 2.2MHz VC BST SWITCH LOGIC AND ANTISHOOT THROUGH BURST DETECT SHDN TSD INTVCC UVLO VIN UVLO CBST M1 L SW M2 PGND SHDN TSD VIN UVLO 2.1µA RT + + – VIN SYNC + – 1.0V R ISP R ISN CF RSEN VOUT COUT 20R 1× 1.4µA GND ICTRL IMON 8613 BD 10 8613f For more information www.linear.com/LT8613 LT8613 Operation The LT8613 is a monolithic, constant frequency, current mode step-down DC/DC converter. An oscillator, with frequency set using a resistor on the RT pin, turns on the internal top power switch at the beginning of each clock cycle. Current in the inductor then increases until the top switch current comparator trips and turns off the top power switch. The peak inductor current at which the top switch turns off is controlled by the voltage on the internal VC node. The error amplifier servos the VC node by comparing the voltage on the VFB pin with an internal 0.97V reference. When the load current increases it causes a reduction in the feedback voltage relative to the reference leading the error amplifier to raise the VC voltage until the average inductor current matches the new load current. When the top power switch turns off, the synchronous power switch turns on until the next clock cycle begins or inductor current falls to zero. If overload conditions result in more than 10A flowing through the bottom switch (valley current), the next clock cycle will be delayed until switch current returns to a safe level. The LT8613 includes a current control and monitoring loop using the ISN, ISP, IMON and ICTRL pins. The ISP/ ISN pins monitor the voltage across an external sense resistor such that the VISP-VISN does not exceed 50mV by limiting the peak inductor current controlled by the VC node. The current sense amplifier inputs (ISP/ISN) are railto-rail such that input, output, or other system currents may be monitored and regulated. The IMON pin outputs a ground-referenced voltage equal to 20 times the voltage between the ISP-ISN pins for monitoring system currents. The ICTRL pin can be used to override the internal 50mV limit between the ISP, ISN pin to a lower set point for the current control loop. To optimize efficiency at light loads, the LT8613 operates in Burst Mode operation in light load situations. Between bursts, all circuitry associated with controlling the output switch is shut down, reducing the input supply current to 1.7μA. In a typical application, 3μA will be consumed from the input supply when regulating with no load. The SYNC pin is tied low to use Burst Mode operation and can be tied to a logic high to use pulse-skipping mode. If a clock is applied to the SYNC pin the part will synchronize to an external clock frequency and operate in pulse-skipping mode. While in pulse-skipping mode the oscillator operates continuously and positive SW transitions are aligned to the clock. During light loads, switch pulses are skipped to regulate the output and the quiescent current will be several hundred µA. To improve efficiency across all loads, supply current to internal circuitry can be sourced from the BIAS pin when biased at 3.3V or above. Else, the internal circuitry will draw current from VIN. The BIAS pin should be connected to VOUT if the LT8613 output is programmed at 3.3V or above. Comparators monitoring the FB pin voltage will pull the PG pin low if the output voltage varies more than ±9% (typical) from the set point, or if a fault condition is present. The oscillator reduces the LT8613’s operating frequency when the voltage at the FB pin is low. This frequency foldback helps to control the inductor current when the output voltage is lower than the programmed value which occurs during start-up or overcurrent conditions. When a clock is applied to the SYNC pin or the SYNC pin is held DC high, the frequency foldback is disabled and the switching frequency will slow down only during overcurrent conditions. If the EN/UV pin is low, the LT8613 is shut down and draws 1µA from the input. When the EN/UV pin is above 1V, the switching regulator will become active. 8613f For more information www.linear.com/LT8613 11 LT8613 Applications Information Achieving Ultralow Quiescent Current To enhance efficiency at light loads, the LT8613 operates in low ripple Burst Mode operation, which keeps the output capacitor charged to the desired output voltage while minimizing the input quiescent current and minimizing output voltage ripple. In Burst Mode operation the LT8613 delivers single small pulses of current to the output capacitor followed by sleep periods where the output power is supplied by the output capacitor. While in sleep mode the LT8613 consumes 1.7μA. As the output load decreases, the frequency of single current pulses decreases (see Figure 1a) and the percentage of time the LT8613 is in sleep mode increases, resulting in Burst Frequency 800 VIN = 12V VOUT = 5V L = 3.9µH SWITCH FREQUENCY (kHz) 700 600 500 400 300 200 100 0 0 100 200 300 400 LOAD CURRENT (mA) (1a) 500 8613 F01a Minimum Load to Full Frequency (SYNC DC High) much higher light load efficiency than for typical converters. By maximizing the time between pulses, the converter quiescent current approaches 2.5µA for a typical application when there is no output load. Therefore, to optimize the quiescent current performance at light loads, the current in the feedback resistor divider must be minimized as it appears to the output as load current. While in Burst Mode operation the current limit of the top switch is approximately 1A resulting in output voltage ripple shown in Figure 2. Increasing the output capacitance will decrease the output ripple proportionally. As load ramps upward from zero the switching frequency will increase but only up to the switching frequency programmed by the resistor at the RT pin as shown in Figure 1a. The output load at which the LT8613 reaches the programmed frequency varies based on input voltage, output voltage, and inductor choice. For some applications it is desirable for the LT8613 to operate in pulse-skipping mode, offering two major differences from Burst Mode operation. First is the clock stays awake at all times and all switching cycles are aligned to the clock. In this mode much of the internal circuitry is awake at all times, increasing quiescent current to several hundred µA. Second is that full switching frequency is reached at lower output load than in Burst Mode operation (see Figure 1b). To enable pulse-skipping mode, the SYNC pin is tied high either to a logic output or to the INTVCC pin. When a clock is applied to the SYNC pin the LT8613 will also operate in pulse-skipping mode. 60 MINIMUM LOAD (mA) 50 IL 1A/DIV 40 VSW 5V/DIV 30 20 5µs/DIV 0 12VIN TO 5VOUT AT 20mA; FRONT PAGE APP VSYNC = 0V FRONT PAGE APPLICATION 10 0 10 20 30 INPUT VOLTAGE (V) (1b) 40 50 Figure 2. Burst Mode Operation 8613 F01b Figure 1. SW Frequency vs Load Information in Burst Mode Operation (1a) and Pulse-Skipping Mode (1b) 12 8613 F02 For more information www.linear.com/LT8613 8613f LT8613 Applications Information FB Resistor Network The output voltage is programmed with a resistor divider between the output and the FB pin. Choose the resistor values according to: where RT is in kΩ and fSW is the desired switching frequency in MHz. Table 1. SW Frequency vs RT Value fSW (MHz) RT (kΩ) 0.2 232 0.3 150 0.4 110 0.5 88.7 0.6 71.5 0.7 60.4 If low input quiescent current and good light-load efficiency are desired, use large resistor values for the FB resistor divider. The current flowing in the divider acts as a load current, and will increase the no-load input current to the converter, which is approximately: 0.8 52.3 1.0 41.2 1.2 33.2 14 28.0 1.6 23.7 V V 1 IQ = 1.7µA + OUT OUT R1+R2 VIN n 1.8 20.5 2.0 18.2 2.2 15.8 V R1= R2 OUT – 1 0.970V (1) Reference designators refer to the Block Diagram. 1% resistors are recommended to maintain output voltage accuracy. (2) where 1.7µA is the quiescent current of the LT8613 and the second term is the current in the feedback divider reflected to the input of the buck operating at its light load efficiency n. For a 3.3V application with R1 = 1M and R2 = 412k, the feedback divider draws 2.3µA. With VIN = 12V and n = 80%, this adds 0.8µA to the 1.7µA quiescent current resulting in 2.5µA no-load current from the 12V supply. Note that this equation implies that the no-load current is a function of VIN; this is plotted in the Typical Performance Characteristics section. When using large FB resistors, a 4.7pF to 10pF phase-lead capacitor should be connected from VOUT to FB. Setting the Switching Frequency The LT8613 uses a constant frequency PWM architecture that can be programmed to switch from 200kHz to 2.2MHz by using a resistor tied from the RT pin to ground. A table showing the necessary RT value for a desired switching frequency is in Table 1. The RT resistor required for a desired switching frequency can be calculated using: RT = 46.5 – 5.2 fSW (3) Operating Frequency Selection and Trade-Offs Selection of the operating frequency is a trade-off between efficiency, component size, and input voltage range. The advantage of high frequency operation is that smaller inductor and capacitor values may be used. The disadvantages are lower efficiency and a smaller input voltage range. The highest switching frequency (fSW(MAX)) for a given application can be calculated as follows: fSW(MAX) = ( VOUT + VSW(BOT) tON(MIN) VIN – VSW(TOP) + VSW(BOT) ) (4) where VIN is the typical input voltage, VOUT is the output voltage, VSW(TOP) and VSW(BOT) are the internal switch drops (~0.4V, ~0.18V, respectively at maximum load) and tON(MIN) is the minimum top switch on-time (see the Electrical Characteristics). This equation shows that a slower switching frequency is necessary to accommodate a high VIN/VOUT ratio. For transient operation, VIN may go as high as the absolute maximum rating of 42V regardless of the RT value, however the LT8613 will reduce switching frequency as necessary to maintain control of inductor current to assure safe operation. 8613f For more information www.linear.com/LT8613 13 LT8613 Applications Information The LT8613 is capable of a maximum duty cycle of greater than 99%, and the VIN-to-VOUT dropout is limited by the RDS(ON) of the top switch. In this mode the LT8613 skips switch cycles, resulting in a lower switching frequency than programmed by RT. For applications that cannot allow deviation from the programmed switching frequency at low VIN/VOUT ratios use the following formula to set switching frequency: VIN(MIN) = VOUT + VSW(BOT) 1– fSW • tOFF(MIN) – VSW(BOT) + VSW(TOP) (5) where ∆IL is the inductor ripple current as calculated in Equation 9 and ILOAD(MAX) is the maximum output load for a given application. As a quick example, an application requiring 4A output should use an inductor with an RMS rating of greater than 4A and an ISAT of greater than 5A. During long duration overload or short-circuit conditons, the inductor RMS is greater to avoid overheating of the inductor. To keep the efficiency high, the series resistance (DCR) should be less than 0.020Ω, and the core material should be intended for high frequency applications. where VIN(MIN) is the minimum input voltage without skipped cycles, VOUT is the output voltage, VSW(TOP) and VSW(BOT) are the internal switch drops (~0.4V, ~0.18V, respectively at maximum load), fSW is the switching frequency (set by RT), and tOFF(MIN) is the minimum switch off-time. Note that higher switching frequency will increase the minimum input voltage below which cycles will be dropped to achieve higher duty cycle. The LT8613 limits the peak switch current in order to protect the switches and the system from overload faults. The top switch current limit (ILIM) is at least 7.5A at low duty cycles and decreases linearly to 6A at DC = 0.8. The inductor value must then be sufficient to supply the desired maximum output current (IOUT(MAX)), which is a function of the switch current limit (ILIM) and the ripple current. Inductor Selection and Maximum Output Current The LT8613 is designed to minimize solution size by allowing the inductor to be chosen based on the output load requirements of the application. During overload or short-circuit conditions the LT8613 safely tolerates operation with a saturated inductor through the use of a high speed peak-current mode architecture. The peak-to-peak ripple current in the inductor can be calculated as follows: A good first choice for the inductor value is: L= VOUT + VSW(BOT) fSW (6) where fSW is the switching frequency in MHz, VOUT is the output voltage, VSW(BOT) is the bottom switch drop (~0.18V) and L is the inductor value in μH. To avoid overheating and poor efficiency, an inductor must be chosen with an RMS current rating that is greater than the maximum expected output load of the application. In addition, the saturation current (typically labeled ISAT) rating of the inductor must be higher than the load current plus 1/2 of in inductor ripple current: 1 IL(PEAK) = ILOAD(MAX) + ∆IL 2 14 (7) IOUT(MAX) = ILIM – ∆IL = VOUT L • fSW ∆IL 2 V • 1– OUT VIN(MAX) (8) (9) where fSW is the switching frequency of the LT8613, and L is the value of the inductor. Therefore, the maximum output current that the LT8613 will deliver depends on the switch current limit, the inductor value, and the input and output voltages. The inductor value may have to be increased if the inductor ripple current does not allow sufficient maximum output current (IOUT(MAX)) given the switching frequency, and maximum input voltage used in the desired application. The optimum inductor for a given application may differ from the one indicated by this design guide. A larger value inductor provides a higher maximum load current and reduces the output voltage ripple. For applications requiring smaller load currents, the value of the inductor may be lower and the LT8613 may operate with higher ripple 8613f For more information www.linear.com/LT8613 LT8613 Applications Information current. This allows use of a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. Be aware that low inductance may result in discontinuous mode operation, which further reduces maximum load current. For more information about maximum output current and discontinuous operation, see Linear Technology’s Application Note 44. Finally, for duty cycles greater than 50% (VOUT/VIN > 0.5), a minimum inductance is required to avoid sub-harmonic oscillation. See Application Note 19. Input Capacitor Bypass the input of the LT8613 circuit with a ceramic capacitor of X7R or X5R type placed as close as possible to the VIN and PGND pins. Y5V types have poor performance over temperature and applied voltage, and should not be used. A 10μF ceramic capacitor is adequate to bypass the LT8613 and will easily handle the ripple current. Note that larger input capacitance is required when a lower switching frequency is used. If the input power source has high impedance, or there is significant inductance due to long wires or cables, additional bulk capacitance may be necessary. This can be provided with a low performance electrolytic capacitor. Step-down regulators draw current from the input supply in pulses with very fast rise and fall times. The input capacitor is required to reduce the resulting voltage ripple at the LT8613 and to force this very high frequency switching current into a tight local loop, minimizing EMI. A 10μF capacitor is capable of this task, but only if it is placed close to the LT8613 (see the PCB Layout section). A second precaution regarding the ceramic input capacitor concerns the maximum input voltage rating of the LT8613. A ceramic input capacitor combined with trace or cable inductance forms a high quality (under damped) tank circuit. If the LT8613 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the LT8613’s voltage rating. This situation is easily avoided (see Linear Technology Application Note 88). Output Capacitor and Output Ripple The output capacitor has two essential functions. Along with the inductor, it filters the square wave generated by the LT8613 to produce the DC output. In this role it determines the output ripple, thus low impedance at the switching frequency is important. The second function is to store energy in order to satisfy transient loads and stabilize the LT8613’s control loop. Ceramic capacitors have very low equivalent series resistance (ESR) and provide the best ripple performance. For good starting values, see the Typical Applications section. Use X5R or X7R types. This choice will provide low output ripple and good transient response. Transient performance can be improved with a higher value output capacitor and the addition of a feedforward capacitor placed between VOUT and FB. Increasing the output capacitance will also decrease the output voltage ripple. A lower value of output capacitor can be used to save space and cost but transient performance will suffer and may cause loop instability. See the Typical Applications in this data sheet for suggested capacitor values. When choosing a capacitor, special attention should be given to the data sheet to calculate the effective capacitance under the relevant operating conditions of voltage bias and temperature. A physically larger capacitor or one with a higher voltage rating may be required. 8613f For more information www.linear.com/LT8613 15 LT8613 Applications Information The LT8613 is in shutdown when the EN pin is low and active when the pin is high. The rising threshold of the EN comparator is 1.0V, with 40mV of hysteresis. The EN pin can be tied to VIN if the shutdown feature is not used, or tied to a logic level if shutdown control is required. Adding a resistor divider from VIN to EN programs the LT8613 to regulate the output only when VIN is above a desired voltage (see the Block Diagram). Typically, this threshold, VIN(EN), is used in situations where the input supply is current limited, or has a relatively high source resistance. A switching regulator draws constant power from the source, so source current increases as source voltage drops. This looks like a negative resistance load to the source and can cause the source to current limit or latch low under low source voltage conditions. The VIN(EN) threshold prevents the regulator from operating at source voltages where the problems might occur. This threshold can be adjusted by setting the values R3 and R4 such that they satisfy the following equation: R3 VIN(EN) = + 1 • 1.0V R4 (10) where the LT8613 will remain off until VIN is above VIN(EN). Due to the comparator’s hysteresis, switching will not stop until the input falls slightly below VIN(EN). When operating in Burst Mode operation for light load currents, the current through the VIN(EN) resistor network can easily be greater than the supply current consumed by the LT8613. Therefore, the VIN(EN) resistors should be large to minimize their effect on efficiency at low loads. Current Control Loop In addition to regulating the output voltage the LT8613 includes a current regulation loop for setting the average input or output current limit as shown in the Typical Applications section. The LT8613 measures voltage drop across an external current sense resistor using the ISP and ISN pins. This resistor may be connected between the inductor and the 16 output capacitor to sense the output current or may be placed between the VIN bypass capacitor and the input power source to sense input current. The current loop modulates the internal cycle-by-cycle switch current limit such that the average voltage across ISP-ISN pins does not exceed 50mV. Care must be taken and filters should be used to assure the signal applied to the ISN and ISP pins has a peak-topeak ripple of less than 30mV for accurate operation. In addition to high crest factor current waveforms such as the input current of DC/DC regulators, another cause of high ripple voltage across the sense resistor is excessive resistor ESL. Typically the problem is solved by using a small ceramic capacitor across the sense resistor or using a filter network between the ISP and ISN pins. The ICTRL pin allows the ISP-ISN set point to be linearly controlled from 50mV to 0mV as the ICTRL pin is ramped from 1V down to 0V, respectively and as shown in Figure 3. When this functionality is unused the ICTRL pin may be tied to INTVCC or floated. In addition the ICTRL pin includes a 2µA pull-up source such that a capacitor may be added for soft-start functionality. The IMON pin is a voltage output proportional to the voltage across the current sense resistor such that VIMON = 20 • (ISP-ISN) as shown in Figure 4. This output can be used to monitor the input or output current of the LT8613 or may be an input to an ADC for further processing. 60 MAX VISP-VISN VOLTAGE (mV) Enable Pin 50 40 30 20 10 0 0 500 1000 1500 ICTRL VOLTAGE (mV) 2000 8613 F03 Figure 3. LT8613 Sense Voltage vs ICTRL Voltage 8613f For more information www.linear.com/LT8613 LT8613 Applications Information 1200 VSYNC = 3.3V 1000 VIMON (mV) 800 600 400 200 0 0 10 20 30 VISP-VISN (mV) 40 50 8613 F04 Figure 4. LT8613 Sense Voltage vs IMON Voltage INTVCC Regulator An internal low dropout (LDO) regulator produces the 3.4V supply from VIN that powers the drivers and the internal bias circuitry. The INTVCC can supply enough current for the LT8613’s circuitry and must be bypassed to ground with a minimum of 1μF ceramic capacitor. Good bypassing is necessary to supply the high transient currents required by the power MOSFET gate drivers. To improve efficiency the internal LDO can also draw current from the BIAS pin when the BIAS pin is at 3.1V or higher. Typically the BIAS pin can be tied to the output of the LT8613, or can be tied to an external supply of 3.3V or above. If BIAS is connected to a supply other than VOUT, be sure to bypass with a local ceramic capacitor. If the BIAS pin is below 3.0V, the internal LDO will consume current from VIN. Applications with high input voltage and high switching frequency where the internal LDO pulls current from VIN will increase die temperature because of the higher power dissipation across the LDO. Do not connect an external load to the INTVCC pin. Output Voltage Tracking and Soft-Start The LT8613 allows the user to program its output voltage ramp rate by means of the TR/SS pin. An internal 2.2μA pulls up the TR/SS pin to INTVCC. Putting an external capacitor on TR/SS enables soft starting the output to prevent current surge on the input supply. During the soft-start ramp the output voltage will proportionally track the TR/SS pin voltage. For output tracking applications, TR/SS can be externally driven by another voltage source. From 0V to 0.97V, the TR/SS voltage will override the internal 0.97V reference input to the error amplifier, thus regulating the FB pin voltage to that of TR/SS pin. When TR/SS is above 0.97V, tracking is disabled and the feedback voltage will regulate to the internal reference voltage. The TR/SS pin may be left floating if the function is not needed. An active pull-down circuit is connected to the TR/SS pin which will discharge the external soft-start capacitor in the case of fault conditions and restart the ramp when the faults are cleared. Fault conditions that clear the soft-start capacitor are the EN/UV pin transitioning low, VIN voltage falling too low, or thermal shutdown. Output Power Good When the LT8613’s output voltage is within the ±9% window of the regulation point, which is a VFB voltage in the range of 0.883V to 1.057V (typical), the output voltage is considered good and the open-drain PG pin goes high impedance and is typically pulled high with an external resistor. Otherwise, the internal pull-down device will pull the PG pin low. To prevent glitching both the upper and lower thresholds include 1.3% of hysteresis. The PG pin is also actively pulled low during several fault conditions: EN/UV pin is below 1V, INTVCC has fallen too low, VIN is too low, or thermal shutdown. Synchronization To select low ripple Burst Mode operation, tie the SYNC pin below 0.4V (this can be ground or a logic low output). To synchronize the LT8613 oscillator to an external frequency connect a square wave (with 20% to 80% duty cycle) to the SYNC pin. The square wave amplitude should have valleys that are below 0.4V and peaks above 2.4V (up to 6V). 8613f For more information www.linear.com/LT8613 17 LT8613 Applications Information The LT8613 will not enter Burst Mode operation at low output loads while synchronized to an external clock, but instead will pulse skip to maintain regulation. The LT8613 may be synchronized over a 200kHz to 2.2MHz range. The RT resistor should be chosen to set the LT8613 switching frequency equal to or below the lowest synchronization input. For example, if the synchronization signal will be 500kHz and higher, the RT should be selected for 500kHz. The slope compensation is set by the RT value, while the minimum slope compensation required to avoid subharmonic oscillations is established by the inductor size, input voltage, and output voltage. Since the synchronization frequency will not change the slopes of the inductor current waveform, if the inductor is large enough to avoid subharmonic oscillations at the frequency set by RT, then the slope compensation will be sufficient for all synchronization frequencies. For some applications it is desirable for the LT8613 to operate in pulse-skipping mode, offering two major differences from Burst Mode operation. First is the clock stays awake at all times and all switching cycles are aligned to the clock. Second is that full switching frequency is reached at lower output load than in Burst Mode operation. These two differences come at the expense of increased quiescent current. To enable pulse-skipping mode, the SYNC pin is tied high either to a logic output or to the INTVCC pin. Frequency foldback behavior depends on the state of the SYNC pin: If the SYNC pin is low the switching frequency will slow while the output voltage is lower than the programmed level. If the SYNC pin is connected to a clock source or tied high, the LT8613 will stay at the programmed frequency without foldback and only slow switching if the inductor current exceeds safe levels. There is another situation to consider in systems where the output will be held high when the input to the LT8613 is absent. This may occur in battery charging applications or in battery-backup systems where a battery or some other supply is diode ORed with the LT8613’s output. If the VIN pin is allowed to float and the EN pin is held high (either by a logic signal or because it is tied to VIN), then the LT8613’s internal circuitry will pull its quiescent current through its SW pin. This is acceptable if the system can tolerate several μA in this state. If the EN pin is grounded the SW pin current will drop to near 1µA. However, if the VIN pin is grounded while the output is held high, regardless of EN, parasitic body diodes inside the LT8613 can pull current from the output through the SW pin and the VIN pin. Figure 5 shows a connection of the VIN and EN/UV pins that will allow the LT8613 to run only when the input voltage is present and that protects against a shorted or reversed input. The LT8613 does not operate in forced continuous mode regardless of SYNC signal. Never leave the SYNC pin floating. Shorted and Reversed Input Protection VIN LT8613 EN/UV GND 8613 F05 The LT8613 will tolerate a shorted output. Several features are used for protection during output short-circuit and brownout conditions. The first is the switching frequency will be folded back while the output is lower than the set point to maintain inductor current control. Second, the bottom switch current is monitored such that if inductor current is beyond safe levels switching of the top switch will be delayed until such time as the inductor current falls to safe levels. 18 D1 VIN Figure 5. Reverse VIN Protection 8613f For more information www.linear.com/LT8613 LT8613 Applications Information PCB Layout For proper operation and minimum EMI, care must be taken during printed circuit board layout. Figure 6 shows the recommended component placement with trace, ground plane and via locations. Note that large, switched currents flow in the LT8613’s VIN pins, PGND pins, and the input capacitor (C1). The loop formed by the input capacitor should be as small as possible by placing the capacitor adjacent to the VIN and PGND pins. When using a physically large input capacitor the resulting loop may become too large in which case using a small case/value capacitor placed close to the VIN and PGND pins plus a larger capacitor further away is preferred. These components, along with the inductor and output capacitor, should be placed on the same side of the circuit board, and their connections should be made on that layer. Place a local, unbroken ground plane under the application circuit on the layer closest to the surface layer. The SW and BOOST nodes should be as small as possible. Finally, keep the FB and RT nodes small so that the ground traces will shield them from the SW and BOOST nodes. The exposed pad on the bottom of the package must be soldered to ground so that the pad is connected to ground electrically and also acts as a heat sink thermally. To keep thermal resistance low, extend the ground plane as much as possible, and add thermal vias under and near the LT8613 to additional ground planes within the circuit board and on the bottom side. ICTRL IMON 28 27 ISN ISP GND 26 25 1 24 TR/SS 2 23 RT 3 22 BIAS 4 21 INTVCC 5 20 6 19 7 18 8 17 9 16 10 15 SYNC EN/UV VIN GND 11 12 13 VOUT FB PG BST SW 14 VOUT VOUT LINE TO BIAS VOUT LINE TO ISN LINE TO ISP VIAS TO GROUND PLANE 8613 F06 OUTLINE OF LOCAL GROUND PLANE Figure 6. Recommended PCB Layout for the LT8613 High Temperature Considerations For higher ambient temperatures, care should be taken in the layout of the PCB to ensure good heat sinking of the LT8613. The exposed pad on the bottom of the package must be soldered to a ground plane. This ground should be tied to large copper layers below with thermal vias; these layers will spread heat dissipated by the LT8613. Placing additional vias can reduce thermal resistance further. The maximum load current should be derated as the ambient temperature approaches the maximum junction rating. Power dissipation within the LT8613 can be estimated by calculating the total power loss from an efficiency measurement and subtracting the inductor loss. The die temperature is calculated by multiplying the LT8613 power dissipation by the thermal resistance from junction to ambient. The LT8613 will stop switching and indicate a fault condition if safe junction temperature is exceeded. 8613f For more information www.linear.com/LT8613 19 LT8613 Typical Applications 5V Step-Down with 5A Output Current Limit VIN 5.8V TO 42V 10µF ON OFF VIN BST 0.1µF EN/UV SYNC IMON 3.3µH 1µF ISP ISN BIAS PG ICTRL INTVCC 0.010Ω SW LT8613 10pF TR/SS 1µF 1M FB RT PGND 52.3k GND VOUT 5V 5A 243k 100µF 8613 TA02 fSW = 800kHz L: VISHAY IHLP2525EZ-01 3.3V Step-Down with 1A Input Current Limit 1µF VIN 4.1V TO 42V 0.050Ω 10µF ON OFF ISN VIN ISP BST 0.10µF EN/UV SYNC IMON 3.3µH LT8613 ICTRL SW BIAS PG INTVCC TR/SS RT 1µF 41.2k PGND GND FB VOUT 3.3V 4.7pF 1M 412k 100µF 8613 TA03 fSW = 1MHz L: VISHAY IHLP2525EZ-01 3.3V Step-Down with 1A Input Current Limit and 7V VIN Undervoltage Lockout VIN 4.1V TO 42V 0.050Ω ISN VIN 1µF 604k 10µF ISP BST 0.1µF EN/UV SYNC 100k IMON 3.3µH LT8613 ICTRL SW BIAS PG INTVCC TR/SS RT 1µF 20 60.4k PGND GND fSW = 700kHz L: VISHAY IHLP2525EZ-01 FB VOUT 3.3V 4.7pF 1M 412k 100µF 8613 TA04 For more information www.linear.com/LT8613 8613f LT8613 Typical Applications Digitally Controlled Current/Voltage Source VIN 4.1V TO 42V VIN 10µH ON OFF BST SYNC µC 0.1µF EN/UV ADC IMON DAC ICTRL 3.3µH SW LT8613 0.008Ω 1µF VOUT 3.3V 6A ISP ISN BIAS INTVCC 4.7pF PG TR/SS RT 1µF PGND 60.4k 1M FB GND 412k 100µF 8613 TA05 fSW = 700kHz L: VISHAY IHLP2525EZ-01 CCCV Battery Charger VIN 5V TO 42V D1 VIN 10µH ON OFF BST 0.1µF EN/UV SYNC IMON 3.3µH 1µF ISP ISN BIAS ICTRL TR/SS RT 1µF 60.4k PGND GND + 10pF PG INTVCC VOUT 4.1V 5A 0.010Ω SW LT8613 Li-Ion BATTERY 324k FB 100k 47µF 8613 TA06 fSW = 700kHz L: VISHAY IHLP2525EZ-01 –3.3V Negative Converter with 2A Output Current Limit VIN 3.8V TO 38V 10µF VIN 0.1µF BST EN/UV SW SYNC 4.7µF ISP LT8613 60.4k IMON ICTRL ISN BIAS INTVCC PG TR/SS RT 1µF 60.4k 0.1µF 4.7µH PGND GND FB 1µF 10pF 1M 412k f = 700kHz L: COILCRAFT XAL6060 47µF 0.025Ω 8613 TA07 VOUT –3.3V 2A 8613f For more information www.linear.com/LT8613 21 LT8613 Typical Applications 2MHz, 3.3V Step-Down with Power Good without Current Sense VIN 4.1V TO 42V 10µF VIN BST EN/UV ON OFF SW ISP ISN BIAS PG SYNC IMON LT8613 ICTRL INTVCC 0.1µF 1µH 150k 1µF PGND GND 18.2k PGOOD 4.7pF TR/SS RT VOUT 3.3V 6A 1M FB 412k f = 2MHz L: VISHAY IHLP2525CZ-01 100µF 8613 TA08 1V Step-Down with 5A Output Current Limit VIN 3.8V TO 42V 10µF VIN ON OFF BST EN/UV SW ISP SYNC IMON LT8613 ICTRL INTVCC 0.1µF 1µH 0.010Ω VOUT 0.97V 5A 1µF ISN BIAS PG FB TR/SS RT 1µF 150k 2×100µF PGND GND f = 300kHz L: VISHAY IHLP2525CZ-01 8613 TA09 12V Step-Down with 5A Output Current Limit VIN 13V TO 42V 10µF VIN ON OFF BST EN/UV SW ISP SYNC IMON LT8613 ICTRL 0.1µF 10µH 0.010Ω VOUT 12V 5A 1µF ISN BIAS PG 10pF INTVCC TR/SS RT 1µF 60.4k PGND GND FB f = 700kHz L: COILCRAFT XAL6060 22 1M 88.7k 22µF 8613 TA10 8613f For more information www.linear.com/LT8613 LT8613 Typical Applications 5A LED Driver VIN 3.8V TO 42V 4.7µF VIN BST EN/UV ON OFF SYNC IMON SW ISP LT8613 ICTRL ISN BIAS PG 0.1µF 4.7µH 0.010Ω 5A D1 1µF 10pF INTVCC TR/SS RT 1µF 60.4k PGND GND FB 420k 100k 10µF 8613 TA11 f = 700kHz L: COILCRAFT XAL6060 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UDE Package 28-Lead Plastic QFN (3mm × 6mm) PIN 1 NOTCH R = 0.20 OR 0.35 × 45° CHAMFER (Reference LTC DWG # 05-08-1926 Rev Ø) 3.00 ±0.10 0.75 ±0.05 1.50 REF 27 R = 0.05 TYP 28 0.40 ±0.10 PIN 1 TOP MARK (NOTE 6) 0.70 ±0.05 3.50 ±0.05 2.10 ±0.05 1.50 REF 1 2 4.75 ±0.05 1.70 ±0.05 4.50 REF 6.00 ±0.10 4.75 ±0.10 PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC 4.50 REF 1.70 ±0.10 5.10 ±0.05 6.50 ±0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE (UDE28) QFN 0612 REV Ø 0.200 REF 0.00 – 0.05 R = 0.115 TYP 0.25 ±0.05 0.50 BSC BOTTOM VIEW—EXPOSED PAD 8613f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. For more information www.linear.com/LT8613 23 LT8613 Typical Application Coincident Tracking Step-Downs Each with 5A Output Current Limit VIN 4.1V TO 42V 10µF VIN ON OFF BST EN/UV SYNC IMON SW ISP LT8611 ICTRL 0.1µF 3.3µH VOUT 3.3V 2A 0.010Ω 1µF ISN BIAS PG 16.5k 10pF 20k INTVCC 0.1µF 1µF TR/SS RT 88.7k PGND GND 232k FB 97.6k 100µF f = 500kHz VIN 10µF ON OFF BST EN/UV SYNC IMON ICTRL SW ISP LT8613 0.1µF 2.2µH VOUT 1.8V 2A 0.010Ω 1µF ISN BIAS PG 4.7pF INTVCC TR/SS RT 1µF 88.7k PGND GND 80.6k FB 93.1k 100µF ×2 8613 TA12 f = 500kHz L: VISHAY IHLP2525EZ-01 Related Parts PART NUMBER DESCRIPTION COMMENTS LT8610A/ LT8610AB 42V, 3.5A, 96% Efficiency, 2.2MHz Synchronous MicroPower Step-Down VIN = 3.4V to 42V, VOUT(MIN) = 0.97V, IQ = 2.5µA, ISD < 1µA, MSOP-16E Package DC/DC Converter with IQ = 2.5µA LT8610AC 42V, 3.5A, 96% Efficiency, 2.2MHz Synchronous MicroPower Step-Down VIN = 3V to 42V, VOUT(MIN) = 0.8V, IQ = 2.5µA, ISD < 1µA, MSOP-16E Package DC/DC Converter with IQ = 2.5µA LT8610 42V, 2.5A, 96% Efficiency, 2.2MHz Synchronous MicroPower Step-Down VIN = 3.4V to 42V, VOUT(MIN) = 0.97V, IQ = 2.5µA, ISD < 1µA, MSOP-16E Package DC/DC Converter with IQ = 2.5µA LT8611 42V, 2.5A, 96% Efficiency, 2.2MHz Synchronous MicroPower Step-Down VIN = 3.4V to 42V, VOUT(MIN) = 0.97V, IQ = 2.5µA, ISD < 1µA, DC/DC Converter with IQ = 2.5µA and Input/Output Current Limit/Monitor 3mm × 5mm QFN-24 Package LT8620 65V, 2.5A, 96% Efficiency, 2.2MHz Synchronous MicroPower Step-Down VIN = 3.4V to 65V, VOUT(MIN) = 0.97V, IQ = 2.5µA, ISD < 1µA, MSOP-16E, 3mm × 5mm QFN-24 Packages DC/DC Converter with IQ = 2.5µA LT8614 42V, 4A, 96% Efficiency, 2.2MHz Synchronous MicroPower Step-Down DC/DC Converter with IQ = 2.5µA VIN = 3.4V to 42V, VOUT(MIN) = 0.97V, IQ = 2.5µA, ISD < 1µA, 3mm × 4mm QFN-18 Package LT8612 42V, 6A, 96% Efficiency, 2.2MHz Synchronous MicroPower Step-Down DC/DC Converter with IQ = 2.5µA VIN = 3.4V to 42V, VOUT(MIN) = 0.97V, IQ = 3.0µA, ISD < 1µA, 3mm × 6mm QFN-28 Package 24 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LT8613 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com/LT8613 8613f LT 1114 • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2012