LT8640/LT8640-1 42V, 5A Synchronous Step-Down Silent Switcher with 2.5µA Quiescent Current Description Features Silent Switcher® Architecture nn Ultralow EMI/EMC Emissions nn Spread Spectrum Frequency Modulation nn High Efficiency at High Frequency nn Up to 96% Efficiency at 1MHz nn Up to 95% Efficiency at 2MHz nn Wide Input Voltage Range: 3.4V to 42V nn 5A Maximum Continuous Output, 7A Peak Transient Output nn Ultralow Quiescent Current Burst Mode® Operation nn 2.5µA I Regulating 12V to 3.3V Q IN OUT nn Output Ripple < 10mV P-P nn Fast Minimum Switch-On Time: 35ns nn Low Dropout Under All Conditions: 100mV at 1A nn Forced Continuous Mode (LT8640-1 Only) nn Safely Tolerates Inductor Saturation in Overload nn Adjustable and Synchronizable: 200kHz to 3MHz nn Peak Current Mode Operation nn Output Soft-Start and Tracking nn Small 18-Lead 3mm × 4mm QFN nn Applications Automotive and Industrial Supplies General Purpose Step-Down nn GSM Power Supplies nn nn The LT®8640/LT8640-1 step-down regulator features Silent Switcher architecture designed to minimize EMI/EMC emissions while delivering high efficiency at frequencies up to 3MHz. Assembled in a 3mm × 4mm QFN, the monolithic construction with integrated power switches and inclusion of all necessary circuitry yields a solution with a minimal PCB footprint. An ultralow 2.5µA quiescent current—with the output in full regulation—enables applications requiring highest efficiency at very small load currents. Transient response remains excellent and output voltage ripple is below 10mVP-P at any load, from zero to full current. The LT8640/LT8640-1 allows high VIN to low VOUT conversion at high frequency with a fast minimum top switch on-time of 35ns. Operation is safe in overload even with a saturated inductor. Essential features are included and easy to use: An opendrain PG pin signals when the output is in regulation. The SYNC/MODE pin selects between Burst Mode operation, spread spectrum mode, synchronization to an external clock, and either pulse-skipping (LT8640) or forced continuous mode (LT8640-1). Soft-start and tracking functionality is accessed via the TR/SS pin. An accurate enable threshold can be set using the EN/UV pin and a resistor at the RT pin programs switch frequency. L, LT, LTC, LTM, Linear Technology, the Linear logo, Silent Switcher and Burst Mode are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application 100 5V 5A Step-Down Converter 3.00 2.63 95 4.7µF 1µF GND1 PG 10nF VIN2 GND2 LT8640/ LT8640-1 BST SYNC/MODE TR/SS fSW = 1MHz 1µF 0.1µF 3.3µH 4.7pF INTVCC RT VOUT 5V 5A SW BIAS 1µF 41.2k 90 1M 47µF FB GND 243k 2.25 EFFICIENCY 85 1.88 80 1.50 1.13 75 70 POWER LOSS 65 60 0.5 8640 TA01a 1 POWER LOSS (W) EN/UV VIN1 EFFICIENCY (%) VIN 5.5V TO 42V 12VIN to 5VOUT Efficiency 0.75 1MHz, L = 3.3µH 2MHz, L = 2.2µH 0.38 3MHz, L = 1µH 0 1.5 2 2.5 3 3.5 4 4.5 5 LOAD CURRENT (A) 8640 TA01b 8640fa For more information www.linear.com/LT8640 1 LT8640/LT8640-1 Pin Configuration VIN, EN/UV, PG...........................................................42V BIAS...........................................................................25V FB, TR/SS ...................................................................4V SYNC Voltage ..............................................................6V Operating Junction Temperature Range (Note 2) LT8640E/LT8640-1E........................... –40°C to 125°C LT8640I/LT8640-1I............................. –40°C to 125°C LT8640H............................................. –40°C to 150°C Storage Temperature Range.......................–65 to 150°C SYNC/MODE 17 PG 20 19 18 FB GND TOP VIEW 16 TR/SS BIAS 1 INTVCC 2 15 RT BST 3 21 SW 13 VIN2 11 GND2 7 8 9 10 GND2 GND1 6 14 EN/UV SW VIN1 4 22 SW SW (Note 1) GND1 Absolute Maximum Ratings UDC PACKAGE 18-LEAD (3mm × 4mm) PLASTIC QFN θJA = 40°C/W, θJC(PAD) = 12°C/W EXPOSED PAD (PINS 21, 22) ARE SW, SHOULD BE SOLDERED TO PCB NOTE: PINS 5 AND 12 ARE REMOVED. CONFIGURATION DOES NOT MATCH JEDEC 20-LEAD PACKAGE OUTLINE Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT8640EUDC#PBF LT8640EUDC#TRPBF LGNJ 18-Lead (3mm × 4mm) Plastic QFN –40°C to 125°C LT8640IUDC#PBF LT8640IUDC#TRPBF LGNJ 18-Lead (3mm × 4mm) Plastic QFN –40°C to 125°C LT8640HUDC#PBF LT8640HUDC#TRPBF LGNJ 18-Lead (3mm × 4mm) Plastic QFN –40°C to 150°C LT8640EUDC-1#PBF LT8640EUDC-1#TRPBF LGVT 18-Lead (3mm × 4mm) Plastic QFN –40°C to 125°C LT8640IUDC-1#PBF LT8640IUDC-1#TRPBF LGVT 18-Lead (3mm × 4mm) Plastic QFN –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. ® For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 2 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. PARAMETER CONDITIONS Minimum Input Voltage VIN Quiescent Current TYP MAX l MIN 2.9 3.4 V l 0.75 0.75 3 10 µA µA l 1.7 1.7 4 10 µA µA 0.3 0.5 mA 21 220 50 350 µA µA 0.970 0.970 0.976 0.982 V V 0.004 0.02 %/V VEN/UV = 0V VEN/UV = 2V, Not Switching, VSYNC = 0V VEN/UV = 2V, Not Switching, VSYNC = 2V (LT8640 Only) VIN Current in Regulation VOUT = 0.97V, VIN = 6V, Output Load = 100µA VOUT = 0.97V, VIN = 6V, Output Load = 1mA l l Feedback Reference Voltage VIN = 6V, ILOAD = 0.5A VIN = 6V, ILOAD = 0.5A l VIN = 4.0V to 42V, ILOAD = 0.5A l Feedback Voltage Line Regulation Feedback Pin Input Current VFB = 1V BIAS Pin Current Consumption VBIAS = 3.3V, ILOAD = 1A, 2MHz Minimum On-Time ILOAD = 1A, SYNC = 0V ILOAD = 1A, SYNC = 3.3V 0.964 0.958 –20 l l Minimum Off-Time Oscillator Frequency RT = 221k, ILOAD = 1A RT = 60.4k, ILOAD = 1A RT = 18.2k, ILOAD = 1A Top Power NMOS On-Resistance ISW = 1A l l l 180 665 1.85 l Bottom Power NMOS On-Resistance VINTVCC = 3.4V, ISW = 1A SW Leakage Current VIN = 42V, VSW = 0V, 42V EN/UV Pin Threshold EN/UV Rising 7.5 35 35 50 50 ns ns 80 110 ns 210 700 2.00 240 735 2.15 kHz kHz MHz 10 mΩ 12.5 28 –15 l 0.94 EN/UV Pin Hysteresis 1.0 VEN/UV = 2V –20 PG Upper Threshold Offset from VFB VFB Falling l 5 PG Lower Threshold Offset from VFB VFB Rising l –5.25 PG Hysteresis mΩ µA 1.06 V mV 20 nA 7.5 10.25 % –8 –10.75 % 0.2 PG Leakage VPG = 3.3V PG Pull-Down Resistance VPG = 0.1V SYNC/MODE Threshold SYNC/MODE DC and Clock Low Level Voltage SYNC/MODE Clock High Level Voltage SYNC/MODE DC High Level Voltage Spread Spectrum Modulation Frequency Range RT = 60.4k, VSYNC = 3.3V Spread Spectrum Modulation Frequency VSYNC = 3.3V TR/SS Source Current –40 l 0.7 1.0 2.3 Fault Condition, TR/SS = 0.1V % 40 nA 700 2000 Ω 0.9 1.2 2.6 1.1 1.4 2.9 V V V 22 % 3 l 1.2 A 15 40 EN/UV Pin Current nA mA 67 Top Power NMOS Current Limit TR/SS Pull-Down Resistance 20 11 UNITS 1.9 200 kHz 2.6 µA Ω 8640fa For more information www.linear.com/LT8640 3 LT8640/LT8640-1 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. PARAMETER CONDITIONS MIN TYP MAX LT8640-1 Output Sink Current in Forced Continuous Mode VFB = 1.01V, L = 6.8µH, RT = 60.4k 0.25 0.6 1 A LT8640-1 VIN to Disable Forced Continuous Mode VIN Rising 35 37 39 V LT8640-1 VFB Offset from Feedback Reference Voltage to Disable Forced Continuous Mode VFB Rising 7 9.5 12 % Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT8640E/LT8640-1E is guaranteed to meet performance specifications from 0°C to 125°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization, and correlation with statistical process controls. The LT8640I/LT8640-1I is guaranteed over the full –40°C to 125°C operating junction temperature range. The LT8640H/LT8640-1H is guaranteed over the full –40°C to 150°C operating junction temperature range. High junction temperatures degrade operating lifetimes. Operating 4 UNITS lifetime is derated at junction temperatures greater than 125°C. The junction temperature (TJ, in °C) is calculated from the ambient temperature (TA in °C) and power dissipation (PD, in Watts) according to the formula: TJ = TA + (PD • θJA) where θJA (in °C/W) is the package thermal impedance. Note 3: This IC includes overtemperature protection that is intended to protect the device during overload conditions. Junction temperature will exceed 150°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature will reduce lifetime. 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Typical Performance Characteristics 12VIN to 3.3VOUT Efficiency vs Frequency EFFICIENCY 95 2.25 90 1.13 75 POWER LOSS 70 65 60 0.5 1 1.75 85 1.40 80 1.05 75 POWER LOSS 65 60 0.5 1 90 L = WE–LHMI1040 0.70 1MHz, L = 2.2μH 2MHz, L = 1μH 0.35 3MHz, L = 1μH 0 1.5 2 2.5 3 3.5 4 4.5 5 LOAD CURRENT (A) 8640 G01 1.8 75 70 60 55 0 0.5 Efficiency at 3.3VOUT Efficiency at 5VOUT 90 90 80 80 2.1 70 70 1.8 75 1.5 65 60 55 50 0 0.5 1 1.2 VIN = 12V 0.9 VIN = 24V 0.6 VIN = 36V fSW = 1MHz 0.3 L = IHLP3232DZ-01, 2.2μH 0 1.5 2 2.5 3 3.5 4 4.5 5 LOAD CURRENT (A) 100 60 50 40 fSW = 1MHz L = IHLP3232DZ-01, 4.7μH VIN = 12V VIN = 24V VIN = 36V 30 20 10 0 0.01 0.1 1 10 100 0.1 1 10 100 LOAD CURRENT (mA) 8640 G06 Reference Voltage VIN = 12V 0.977 EFFICIENCY (%) 88 86 VIN = 12V VOUT = 3.3V ILOAD = 2A L = IHLP3232DZ-01, 4.7μH VIN = 24V 85 80 75 VOUT = 5V ILOAD = 10mA L = IHLP3232DZ-01 70 3 8640 G07 REFERENCE VOLAGE (V) 90 90 65 1000 0.979 92 EFFICIENCY (%) 0 0.01 Burst Mode Operation Efficiency vs Inductor Value 94 2 1.5 2.5 0.5 1 SWITCHING FREQUENCY (MHz) fSW = 1MHz L = IHLP3232DZ-01, 4.7μH VIN = 12V VIN = 24V VIN = 36V 30 10 95 0 40 8640 G05 96 82 50 LOAD CURRENT (mA) Efficiency vs Frequency 84 60 20 1000 8640 G04 80 EFFICIENCY (%) 80 EFFICIENCY (%) 2.7 2.4 POWER LOSS (W) 95 70 1 8640 G03 90 POWER LOSS 1.2 VIN = 12V 0.9 VIN = 24V 0.6 VIN = 36V fSW = 1MHz 0.3 L = IHLP3232DZ-01, 3.3μH 0 1.5 2 2.5 3 3.5 4 4.5 5 LOAD CURRENT (A) 65 50 1.5 POWER LOSS 100 EFFICIENCY 2.1 80 3.0 85 2.4 EFFICIENCY 85 8640 G02 Efficiency at 3.3VOUT 100 EFFICIENCY (%) 2.7 2.10 EFFICIENCY 70 L = WE–LHMI1040 0.75 1MHz, L = 3.3µH 2MHz, L = 2.2µH 0.38 3MHz, L = 1µH 0 1.5 2 2.5 3 3.5 4 4.5 5 LOAD CURRENT (A) 3.0 95 POWER LOSS (W) 1.50 80 100 2.45 POWER LOSS (W) 1.88 85 POWER LOSS (W) EFFICIENCY (%) 90 2.63 EFFICIENCY (%) 95 Efficiency at 5VOUT 2.80 100 3.00 100 EFFICIENCY (%) 12VIN to 5VOUT Efficiency vs Frequency 1 2 3 4 5 6 INDUCTOR VALUE (µH) 0.973 0.971 0.969 0.967 0.965 0.963 8 7 0.975 8640 G08 0.961 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 8640 G09 8640fa For more information www.linear.com/LT8640 5 LT8640/LT8640-1 Typical Performance Characteristics EN Pin Thresholds 0.12 0.10 1.02 0.10 1.00 0.99 0.98 0.08 CHANGE IN VOUT (%) EN RISING 1.01 CHANGE IN VOUT (%) EN THRESHOLD (V) Line Regulation Load Regulation 0.15 1.03 0.05 0 –0.05 0.97 EN FALLING 0.95 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) –0.15 0.02 0 –0.04 VOUT = 5V VIN = 12V R1/R2 = 100k/24.3k 0 0.5 1.5 2 2.5 3 3.5 LOAD CURRENT (A) 1 4 4.5 5 –0.08 5 10 15 20 25 30 35 INPUT VOLTAGE (V) 40 45 8640 G12 Top FET Current Limit vs Duty Cycle No-Load Supply Current 4.0 Top FET Current Limit 10.0 12.0 9.5 3.5 2.5 2.0 CURRENT LIMIT (A) CURRENT LIMIT (A) 9.0 3.0 8.5 8.0 7.5 11.0 VOUT = 3.3V L = 4.7µH IN REGULATION 0 5 10 15 20 25 30 35 INPUT VOLTAGE (V) 40 5% DC 10.0 9.0 7.0 1.5 1.0 VOUT = 5V ILOAD = 1A R1/R2 = 100k/24.3k –0.06 8640 G11 8640 G10 INPUT CURRENT (µA) 0.04 –0.02 –0.10 0.96 0.06 6.5 6.0 45 0 0.2 0.4 0.6 DUTY CYCLE 8640 G13 0.8 8.0 –50 –25 1 0 25 50 75 100 125 150 TEMPERATURE (°C) 8640 G14 8640 G15 Switch Drop SWITCH CURRENT = 1A SWITCH DROP (mV) SWITCH DROP (mV) TOP SWITCH 75 50 BOTTOM SWITCH 25 0 25 50 75 100 125 150 TEMPERATURE (°C) 8640 G16 350 300 TOP SWITCH 250 200 150 100 37 34 31 28 50 0 VSYNC = FLOAT VSYNC = 0V 40 400 100 6 43 450 125 0 –50 –25 Minimum On-Time Switch Drop 500 MINIMUM ON-TIME (s) 150 BOTTOM SWITCH 0 1 4 2 3 SWITCH CURRENT (A) 5 25 –50 ILOAD = 2A –25 0 25 50 75 TEMPERATURE (°C) 100 125 8640 G18 8640 G17 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Typical Performance Characteristics Switching Frequency Dropout Voltage 740 600 VIN = 5V VOUT SET TO REGULATE AT 5V L = IHLP3232DZ-01, 1µH FRONT PAGE APPLICATION VIN = 12V 1000 VOUT = 5V 300 200 100 SWITCHING FREQUENCY (kHz) 400 0 RT = 60.4k 730 SWITCHING FREQUENCY (kHz) DROPOUT VOLTAGE (mV) 500 Burst Frequency 1200 720 710 700 690 680 670 0 0.5 1.5 2 2.5 3 3.5 LOAD CURRENT (A) 1 4 4.5 660 –50 –25 5 0 20 600 1.0 500 400 300 20 25 30 35 INPUT VOLTAGE (V) 40 0 45 0 0.2 0.4 0.6 FB VOLTAGE (V) PG THRESHOLD OFFSET FROM VREF (%) SS PIN CURRENT (µA) 0 1 1.9 1.8 1.7 1.6 1.5 25 50 75 100 125 150 TEMPERATURE (°C) 8640 G25 0 0.2 1.0 0.4 0.6 0.8 TR/SS VOLTAGE (V) 1.4 PG Low Thresholds –6.0 9.5 9.0 8.5 8.0 7.5 1.2 8640 G24 PG High Thresholds 2.0 0 0.8 10.0 VSS = 0.5V 1.4 –50 –25 0.4 8640 G23 Soft-Start Current 2.1 0.6 0.2 8640 G22 2.2 0.8 200 PG THRESHOLD OFFSET FROM VREF (%) 15 400 Soft-Start Tracking 100 10 100 200 300 LOAD CURRENT (mA) 1.2 FB VOLTAGE (V) 40 0 8640 G21 VOUT = 3.3V VIN = 12V VSYNC = 0V RT = 60.4k 700 SWITCHING FREQUENCY (kHz) LOAD CURRENT (mA) 800 FRONT PAGE APPLICATION VOUT = 5V fSW = 1MHz 5 200 Frequency Foldback 60 0 400 8640 G20 Minimum Load to Full Frequency (Pulse-Skipping Mode) 80 600 0 25 50 75 100 125 150 TEMPERATURE (°C) 8640 G19 100 800 FB RISING FB FALLING 7.0 6.5 6.0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 8640 G26 –6.5 –7.0 –7.5 FB RISING –8.0 –8.5 FB FALLING –9.0 –9.5 –10.0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 8640 G27 8640fa For more information www.linear.com/LT8640 7 LT8640/LT8640-1 Typical Performance Characteristics RT Programmed Switching Frequency 3.6 225 8.5 3.4 200 125 100 75 BIAS PIN CURRENT (mA) 150 3.0 2.8 2.6 2.4 50 0 0.2 0.6 1.4 1.8 2.2 2.6 1 SWITCHING FREQUENCY (MHz) 2.0 –55 –25 3 95 65 35 TEMPERATURE (°C) 5 125 Bias Pin Current 80 10 5 2.6 1.4 1.8 2.2 0.6 1 SWITCHING FREQUENCY (MHz) 3 90 DC2202A DEMO BOARD VIN = 12V, fSW = 1MHz VIN = 24V, fSW = 1MHz VIN = 12V, fSW = 2MHz VIN = 24V, fSW = 2MHz 70 60 40 30 20 0 0 1 2 3 LOAD CURRENT (A) 4 5 70 60 40 45 50 40 30 20 0 0 0.2 0.4 0.6 DUTY CYCLE OF 7A LOAD 0.8 8640 G33 8640 G32 Switching Waveforms, Burst Mode Operation Switching Waveforms IL 1A/DIV VSW 10V/DIV VSW 5V/DIV 8 20 25 30 35 INPUT VOLTAGE (V) 10 IL 500mA/DIV 8640 G34 15 DC2202A DEMO BOARD VIN = 12V VOUT = 5V fSW = 2MHz STANDBY LOAD = 0.25A PULSED LOAD = 7A 80 50 Switching Waveforms, Full Frequency Continuous Operation VSW 5V/DIV 10 Case Temperature Rise vs 7A Pulsed Load 8640 G31 IL 1A/DIV 5 8640 G30 10 500ns/DIV FRONT PAGE APPLICATION 12VIN TO 5VOUT AT 1A 5.5 155 CASE TEMPERATURE RISE (°C) VBIAS = 5V VOUT = 5V VIN = 12V ILOAD = 1A 0 0.2 6.5 Case Temperature Rise CASE TEMPERATURE RISE (°C) BIAS PIN CURRENT (mA) 15 7.0 8640 G29 8640 G28 20 7.5 6.0 2.2 25 VBIAS = 5V VOUT = 5V ILOAD = 1A fSW = 1MHz 8.0 3.2 175 INPUT VOLTAGE (V) RT PIN RESISTOR (kΩ) Bias Pin Current VIN UVLO 250 5µs/DIV FRONT PAGE APPLICATION 12VIN TO 5VOUT AT 10mA VSYNC = 0V 8640 G35 500ns/DIV FRONT PAGE APPLICATION 36VIN TO 5VOUT AT 1A 8640 G36 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Typical Performance Characteristics Transient Response; Load Current Stepped from 100mA (Burst Mode Operation) to 1.1A Transient Response; Load Current Stepped from 1A to 2A IL 1A/DIV IL 1A/DIV VOUT 100mV/DIV VOUT 200mV/DIV 50µs/DIV FRONT PAGE APPLICATION 1A TO 2A TRANSIENT 12VIN, 5VOUT COUT = 47µF 50µs/DIV FRONT PAGE APPLICATION 100mA (Burst Mode OPERATION) TO 1.1A TRANSIENT 12VIN, 5VOUT COUT = 47µF 8640 G37 Start-Up Dropout Performance Start-Up Dropout Performance VIN VIN 2V/DIV VIN VIN 2V/DIV VOUT VOUT 2V/DIV VOUT VOUT 2V/DIV 100ms/DIV 2.5Ω LOAD (2A IN REGULATION) 8640 G38 100ms/DIV 20Ω LOAD (250mA IN REGULATION) 8640 G39 8640 G40 Conducted EMI Performance 60 50 AMPLITUDE (dBµV) 40 30 20 10 0 -10 -20 FIXED FREQUENCY MODE SPREAD SPECTRUM MODE -30 -40 0 3 6 9 12 15 18 21 24 FREQUENCY (MHz) 27 30 8640 G41 DC2202A DEMO BOARD (WITH EMI FILTER INSTALLED) 14V INPUT TO 5V OUTPUT AT 4A, fSW = 2MHz 8640fa For more information www.linear.com/LT8640 9 LT8640/LT8640-1 Typical Performance Characteristics Radiated EMI Performance (CISPR25 Radiated Emission Test with Class 5 Peak Limits) 50 VERTICAL POLARIZATION PEAK DETECTOR 45 AMPLITUDE (dBµV/m) 40 35 30 25 20 15 10 5 CLASS 5 PEAK LIMIT FIXED FREQUENCY MODE SPREAD SPECTRUM MODE 0 -5 0 100 200 300 400 500 600 700 800 900 1000 FREQUENCY (MHz) 50 HORIZONTAL POLARIZATION PEAK DETECTOR 45 AMPLITUDE (dBµV/m) 40 35 30 25 20 15 10 5 CLASS 5 PEAK LIMIT FIXED FREQUENCY MODE SPREAD SPECTRUM MODE 0 -5 0 100 200 300 400 500 600 700 800 900 1000 FREQUENCY (MHz) DC2202A DEMO BOARD (WITH EMI FILTER INSTALLED) 14V INPUT TO 5V OUTPUT AT 4A, fSW = 2MHz 10 8640 G42 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Pin Functions BIAS (Pin 1): The internal regulator will draw current from BIAS instead of VIN when BIAS is tied to a voltage higher than 3.1V. For output voltages of 3.3V to 25V this pin should be tied to VOUT. If this pin is tied to a supply other than VOUT use a 1µF local bypass capacitor on this pin. If no supply is available, tie to GND. INTVCC (Pin 2): Internal 3.4V Regulator Bypass Pin. The internal power drivers and control circuits are powered from this voltage. INTVCC maximum output current is 20mA. Do not load the INTVCC pin with external circuitry. INTVCC current will be supplied from BIAS if BIAS > 3.1V, otherwise current will be drawn from VIN. Voltage on INTVCC will vary between 2.8V and 3.4V when BIAS is between 3.0V and 3.6V. Decouple this pin to power ground with at least a 1µF low ESR ceramic capacitor placed close to the IC. BST (Pin 3): This pin is used to provide a drive voltage, higher than the input voltage, to the topside power switch. Place a 0.1µF boost capacitor as close as possible to the IC. VIN1 (Pin 4): The LT8640/LT8640-1 requires two 1µF small input bypass capacitors. One 1µF capacitor should be placed between VIN1 and GND1. A second 1µF capacitor should be placed between VIN2 and GND2. These capacitors must be placed as close as possible to the LT8640/ LT8640-1. A third larger capacitor of 2.2µF or more should be placed close to the LT8640/LT8640-1 with the positive terminal connected to VIN1 and VIN2, and the negative terminal connected to ground. See applications section for sample layout. GND1 (6, 7): Power Switch Ground. These pins are the return path of the internal bottom side power switch and must be tied together. Place the negative terminal of the input capacitor as close to the GND1 pins as possible. Also be sure to tie GND1 to the ground plane. See the Applications Information section for sample layout. SW (Pins 8, 9): The SW pins are the outputs of the internal power switches. Tie these pins together and connect them to the inductor and boost capacitor. This node should be kept small on the PCB for good performance and low EMI. GND2 (10, 11): Power Switch Ground. These pins are the return path of the internal bottom side power switch and must be tied together. Place the negative terminal of the input capacitor as close to the GND2 pins as possible. Also be sure to tie GND2 to the ground plane. See the Applications Information section for sample layout. VIN2 (Pin 13): The LT8640/LT8640-1 requires two 1µF small input bypass capacitors. One 1µF capacitor should be placed between VIN1 and GND1. A second 1µF capacitor should be placed between VIN2 and GND2. These capacitors must be placed as close as possible to the LT8640/ LT8640-1. A third larger capacitor of 2.2µF or more should be placed close to the LT8640/LT8640-1 with the positive terminal connected to VIN1 and VIN2, and the negative terminal connected to ground. See the Applications Information section for sample layout. EN/UV (Pin 14): The LT8640/LT8640-1 is shut down when this pin is low and active when this pin is high. The hysteretic threshold voltage is 1.00V going up and 0.96V going down. Tie to VIN if the shutdown feature is not used. An external resistor divider from VIN can be used to program a VIN threshold below which the LT8640/LT8640-1 will shut down. RT (Pin 15): A resistor is tied between RT and ground to set the switching frequency. TR/SS (Pin 16): Output Tracking and Soft-Start Pin. This pin allows user control of output voltage ramp rate during start-up. A TR/SS voltage below 0.97V forces the LT8640/LT8640-1 to regulate the FB pin to equal the TR/ SS pin voltage. When TR/SS is above 0.97V, the tracking function is disabled and the internal reference resumes control of the error amplifier. An internal 1.9µA pull-up current from INTVCC on this pin allows a capacitor to program output voltage slew rate. This pin is pulled to ground with an internal 200Ω MOSFET during shutdown and fault conditions; use a series resistor if driving from a low impedance output. This pin may be left floating if the tracking function is not needed. SYNC/MODE (Pin 17, LT8640 Only): This pin programs four different operating modes: 1) Burst Mode operation. Tie this pin to ground for Burst Mode operation at low output loads—this will result in ultralow quiescent current. 2) Pulse-skipping mode. This mode offers full frequency operation down to low output loads before pulse skipping occurs. Float this pin for pulse-skipping mode. When floating, pin leakage currents should be <1µA. 3) Spread 8640fa For more information www.linear.com/LT8640 11 LT8640/LT8640-1 Pin Functions spectrum mode. Tie this pin high to INTVCC (~3.4V) for pulse-skipping mode with spread spectrum modulation. 4) Synchronization mode. Drive this pin with a clock source to synchronize to an external frequency. During synchronization the part will operate in pulse-skipping mode. GND (Pins 18): LT8640/LT8640-1 Ground Pin. Connect this pin to system ground and to the ground plane. PG (Pin 19): The PG pin is the open-drain output of an internal comparator. PG remains low until the FB pin is within ±8% of the final regulation voltage, and there are no fault conditions. PG is valid when VIN is above 3.4V, regardless of EN/UV pin state. SYNC/MODE (Pin 17, LT8640-1 Only): For the LT8640-1, this pin programs four different operating modes: 1) Burst Mode operation. Tie this pin to ground for Burst Mode operation at low output loads—this will result in ultralow quiescent current. 2) Forced Continuous mode (FCM). This mode offers fast transient response and full frequency operation over a wide load range. Float this pin for FCM. When floating, pin leakage currents should be <1µA. 3) Spread spectrum mode. Tie this pin high to INTVCC (~3.4V) for forced continuous mode with spread-spectrum modulation. 4) Synchronization mode. Drive this pin with a clock source to synchronize to an external frequency. During synchronization the part will operate in forced continuous mode. FB (Pin 20): The LT8640/LT8640-1 regulates the FB pin to 0.970V. Connect the feedback resistor divider tap to this pin. Also, connect a phase lead capacitor between FB and VOUT. Typically, this capacitor is 4.7pF to 22pF. SW (Exposed Pad Pins 21, 22): The exposed pads should be connected and soldered to the SW trace for good thermal performance. If necessary due to manufacturing limitations Pins 21 and 22 may be left disconnected, however thermal performance will be degraded. Block Diagram VIN 4 CIN3 VIN2 VIN1 CIN1 R3 OPT 14 R4 OPT 19 INTERNAL 0.97V REF EN/UV 1V PG + – SHDN ±8% + + – VOUT C1 R2 R1 20 CSS OPT 16 RT 15 17 FB TR/SS INTVCC OSCILLATOR 200kHz TO 3MHz VC BST BURST DETECT SHDN THERMAL SHDN INTVCC UVLO VIN UVLO 1.9µA BIAS 3.4V REG SLOPE COMP ERROR AMP 13 CIN2 – + SWITCH LOGIC AND ANTISHOOT THROUGH 1 2 CVCC 3 CBST M1 L SW 8, 9, 21, 22 VOUT COUT M2 GND1 SHDN THERMAL SHDN VIN UVLO 6, 7 GND2 10, 11 RT SYNC/MODE GND 18 12 8640 BD 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Operation The LT8640/LT8640-1 is a monolithic, constant frequency, current mode step-down DC/DC converter. An oscillator, with frequency set using a resistor on the RT pin, turns on the internal top power switch at the beginning of each clock cycle. Current in the inductor then increases until the top switch current comparator trips and turns off the top power switch. The peak inductor current at which the top switch turns off is controlled by the voltage on the internal VC node. The error amplifier servos the VC node by comparing the voltage on the VFB pin with an internal 0.97V reference. When the load current increases it causes a reduction in the feedback voltage relative to the reference leading the error amplifier to raise the VC voltage until the average inductor current matches the new load current. When the top power switch turns off, the synchronous power switch turns on until the next clock cycle begins or inductor current falls to zero. If overload conditions result in more than 10A flowing through the bottom switch, the next clock cycle will be delayed until switch current returns to a safe level. If the EN/UV pin is low, the LT8640/LT8640-1 is shut down and draws 1µA from the input. When the EN/UV pin is above 1V, the switching regulator will become active. To optimize efficiency at light loads, the LT8640/LT8640-1 operates in Burst Mode operation in light load situations. Between bursts, all circuitry associated with controlling the output switch is shut down, reducing the input supply current to 1.7µA. In a typical application, 2.5µA will be consumed from the input supply when regulating with no load. The SYNC/MODE pin is tied low to use Burst Mode operation and can be floated to use pulse-skipping mode (LT8640) or forced continuous mode (FCM) (LT8640-1). If a clock is applied to the SYNC/MODE pin, the part will synchronize to an external clock frequency and operate in either pulse-skipping mode (LT8640) or FCM (LT8640-1). While in pulse-skipping mode (LT8640 only), the oscillator operates continuously and positive SW transitions are aligned to the clock. During light loads, switch pulses are skipped to regulate the output and the quiescent current will be several hundred µA. The LT8640-1 can operate in forced continuous mode (FCM) for fast transient response and full frequency operation over a wide load range. When in FCM the oscillator operates continuously and positive SW transitions are aligned to the clock. Negative inductor current is allowed. The LT8640-1 can sink current from the output and return this charge to the input in this mode, improving load step transient response. To improve EMI/EMC, the LT8640/LT8640-1 can operate in spread spectrum mode. This feature varies the clock with a triangular frequency modulation of +20%. For example, if the LT8640/LT8640-1’s frequency is programmed to switch at 2MHz, spread spectrum mode will modulate the oscillator between 2MHz and 2.4MHz. The SYNC/ MODE pin should be tied high to INTVCC (~3.4V) to enable spread spectrum modulation with either pulse-skipping mode (LT8640) or forced continuous mode (LT8640-1). To improve efficiency across all loads, supply current to internal circuitry can be sourced from the BIAS pin when biased at 3.3V or above. Else, the internal circuitry will draw current from VIN. The BIAS pin should be connected to VOUT if the LT8640/LT8640-1 output is programmed at 3.3V to 25V. Comparators monitoring the FB pin voltage will pull the PG pin low if the output voltage varies more than ±8% (typical) from the set point, or if a fault condition is present. The oscillator reduces the LT8640/LT8640-1’s operating frequency when the voltage at the FB pin is low. This frequency foldback helps to control the inductor current when the output voltage is lower than the programmed value which occurs during start-up or overcurrent conditions. When a clock is applied to the SYNC/MODE pin, the SYNC/MODE pin is floated, or held DC high, the frequency foldback is disabled and the switching frequency will slow down only during overcurrent conditions. 8640fa For more information www.linear.com/LT8640 13 LT8640/LT8640-1 Applications Information Low EMI PCB Layout Note that large, switched currents flow in the LT8640/ LT8640-1 VIN1, VIN2, GND1, and GND2 pins and the input capacitors (CIN1, CIN2). The loops formed by the input capacitors should be as small as possible by placing the capacitors adjacent to the VIN1/2 and GND1/2 pins. Capacitors with small case size such as 0603 are optimal due to lowest parasitic inductance. The LT8640/LT8640-1 is specifically designed to minimize EMI/EMC emissions and also to maximize efficiency when switching at high frequencies. For optimal performance the LT8640/LT8640-1 requires the use of multiple VIN bypass capacitors. Two small 1µF capacitors should be placed as close as possible to the LT8640/LT8640-1: One capacitor should be tied to VIN1/GND1; a second capacitor should be tied to VIN2/GND2. A third capacitor with a larger value, 2.2µF or higher, should be placed near VIN1 or VIN2. The input capacitors, along with the inductor and output capacitors, should be placed on the same side of the circuit board, and their connections should be made on that layer. Place a local, unbroken ground plane under the application circuit on the layer closest to the surface layer. The SW and BOOST nodes should be as small as possible. Finally, keep the FB and RT nodes small so that the ground traces will shield them from the SW and BOOST nodes. See Figure 1 for a recommended PCB layout. For more detail and PCB design files refer to the Demo Board guide for the LT8640/LT8640-1. GROUND PLANE ON LAYER 2 C1 R1 RPG V R2 CVCC CSS V V 1 V 16 17 20 V V 22 CIN1 6 21 7 RT 10 11 CIN2 CIN3 CBST L GROUND VIA VIN VIA VOUT VIA COUT V OTHER SIGNAL VIAS 8640 F01 Figure 1. Recommended PCB Layout for the LT8640/LT8640-1 14 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Applications Information The exposed pad on the bottom of the package should be soldered to SW to reduce thermal resistance to ambient. To keep thermal resistance low, extend the ground plane from GND1 and GND2 as much as possible, and add thermal vias to additional ground planes within the circuit board and on the bottom side. Achieving Ultralow Quiescent Current (Burst Mode Operation) of time the LT8640/LT8640-1 is in sleep mode increases, resulting in much higher light load efficiency than for typical converters. By maximizing the time between pulses, the converter quiescent current approaches 2.5µA for a typical application when there is no output load. Therefore, to optimize the quiescent current performance at light loads, the current in the feedback resistor divider must be minimized as it appears to the output as load current. As the output load decreases, the frequency of single current pulses decreases (see Figure 2a) and the percentage In order to achieve higher light load efficiency, more energy must be delivered to the output during the single small pulses in Burst Mode operation such that the LT8640/LT8640-1 can stay in sleep mode longer between each pulse. This can be achieved by using a larger value inductor (i.e., 4.7µH), and should be considered independent of switching frequency when choosing an inductor. For example, while a lower inductor value would typically be used for a high switching frequency application, if high light load efficiency is desired, a higher inductor value should be chosen. See curve in Typical Performance Characteristics. Burst Frequency Minimum Load to Full Frequency (Pulse-Skipping Mode) To enhance efficiency at light loads, the LT8640/LT8640-1 operates in low ripple Burst Mode operation, which keeps the output capacitor charged to the desired output voltage while minimizing the input quiescent current and minimizing output voltage ripple. In Burst Mode operation the LT8640/LT8640-1 delivers single small pulses of current to the output capacitor followed by sleep periods where the output power is supplied by the output capacitor. While in sleep mode the LT8640/LT8640-1 consumes 1.7µA. 1200 100 800 600 400 60 40 20 200 0 FRONT PAGE APPLICATION VOUT = 5V fSW = 1MHz 80 LOAD CURRENT (mA) SWITCHING FREQUENCY (kHz) FRONT PAGE APPLICATION VIN = 12V 1000 VOUT = 5V 0 100 200 300 LOAD CURRENT (mA) (2a) 400 0 5 10 15 20 25 30 35 INPUT VOLTAGE (V) 8640 F02a 40 45 8640 F02b (2b) Figure 2. SW Frequency vs Load Information in Burst Mode Operation (2a) and Pulse-Skipping Mode (2b) 8640fa For more information www.linear.com/LT8640 15 LT8640/LT8640-1 Applications Information While in Burst Mode operation the current limit of the top switch is approximately 900mA (as shown in Figure 3), resulting in low output voltage ripple. Increasing the output capacitance will decrease output ripple proportionally. As load ramps upward from zero the switching frequency will increase but only up to the switching frequency programmed by the resistor at the RT pin as shown in Figure 2a. The output load at which the LT8640/LT8640-1 reaches the programmed frequency varies based on input voltage, output voltage and inductor choice. To select low ripple Burst Mode operation, tie the SYNC/MODE pin below 0.4V (this can be ground or a logic low output). IL 500mA/DIV VSW 5V/DIV 5µs/DIV FRONT PAGE APPLICATION 12VIN TO 5VOUT AT 10mA VSYNC = 0V 8640 F03 Figure 3. Burst Mode Operation Forced Continuous Mode (LT8640-1 Only) The LT8640-1 can operate in forced continuous mode (FCM) for fast transient response and full frequency operation over a wide load range. When in FCM, the oscillator operates continuously and positive SW transitions are aligned to the clock. Negative inductor current is allowed at light loads or under large transient conditions. The LT8640-1 can sink current from the output and return this charge to the input in this mode, improving load step transient response (see Figure 4). At light loads, FCM operation is less efficient than Burst Mode operation or pulse-skipping mode, but may be desirable in applications where it is necessary to keep switching harmonics out of the signal band. FCM must be used if the output is required to sink current. To enable FCM (LT8640-1 only), float the SYNC/MODE pin. Leakage current on this pin should be <1µA. FCM is disabled if the VIN pin is held above 37V or if the FB pin is held greater than 9.5% above the feedback reference voltage. FCM is also disabled during soft-start until the soft-start capacitor is fully charged. When FCM is disabled in these ways, negative inductor current is not allowed and the LT8640-1 operates in pulse-skipping mode. For robust operation over a wide VIN and VOUT range, use an inductor value greater than LMIN: Pulse-Skipping Mode (LT8640 Only) For some applications, it is desirable for the LT8640 to operate in pulse-skipping mode, offering two major differences from Burst Mode operation. First is the clock stays awake at all times and all switching cycles are aligned to the clock. In this mode, much of the internal circuitry is awake at all times, increasing quiescent current to several hundred µA. Second is that full switching frequency is reached at lower output load than in Burst Mode operation (see Figure 2b). To enable pulse-skipping mode (LT8640 only), float the SYNC/MODE pin. Leakage current on this pin should be <1µA. LMIN = VOUT ⎛ VOUT ⎞ • ⎜ 1– ⎟ 2 • fSW ⎝ 40 ⎠ FRONT PAGE APPLICATION 100mA to 1.1A TRANSIENT BURST MODE VOUT 200mA/DIV FCM ILOAD 1A/DIV 12VIN, 5VOUT COUT = 47µF 50µs/DIV 8640 F04 Figure 4. Load Step Transient Response with and without Forced Continuous Mode 16 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Applications Information Spread Spectrum Mode FB Resistor Network The LT8640/LT8640-1 features spread spectrum operation to further reduce EMI/EMC emissions. To enable spread spectrum operation, the SYNC/MODE pin should be tied high to INTVCC (~3.4V). In this mode, triangular frequency modulation is used to vary the switching frequency between the value programmed by RT to approximately 20% higher than that value. The modulation frequency is approximately 3kHz. For example, when the LT8640/ LT8640-1 is programmed to 2MHz, the frequency will vary from 2MHz to 2.4MHz at a 3kHz rate. When spread spectrum operation is selected, Burst Mode operation is disabled, and the part will run in either pulse-skipping mode (LT8640) or forced continuous mode (LT8640-1). The output voltage is programmed with a resistor divider between the output and the FB pin. Choose the resistor values according to: Synchronization To synchronize the LT8640/LT8640-1 oscillator to an external frequency, connect a square wave (with 20% to 80% duty cycle) to the SYNC/MODE pin. The square wave amplitude should have valleys that are below 0.4V and peaks above 1.5V (up to 6V). The LT8640/LT8640-1 will not enter Burst Mode operation at low output loads while synchronized to an external clock, but instead will pulse-skip (LT8640) or run forced continuous mode (LT8640-1) to maintain regulation. The LT8640/LT8640-1 may be synchronized over a 200kHz to 3MHz range. The RT resistor should be chosen to set the LT8640/LT8640-1 switching frequency equal to or below the lowest synchronization input. For example, if the synchronization signal will be 500kHz and higher, the RT should be selected for 500kHz. The slope compensation is set by the RT value, while the minimum slope compensation required to avoid subharmonic oscillations is established by the inductor size, input voltage and output voltage. Since the synchronization frequency will not change the slopes of the inductor current waveform, if the inductor is large enough to avoid subharmonic oscillations at the frequency set by RT, then the slope compensation will be sufficient for all synchronization frequencies. ⎛ V ⎞ R1= R2 ⎜ OUT – 1⎟ ⎝ 0.970V ⎠ (1) Reference designators refer to the Block Diagram. 1% resistors are recommended to maintain output voltage accuracy. If low input quiescent current and good light-load efficiency are desired, use large resistor values for the FB resistor divider. The current flowing in the divider acts as a load current, and will increase the no-load input current to the converter, which is approximately: ⎛ V ⎞ ⎛ V ⎞ ⎛ 1⎞ IQ = 1.7µA + ⎜ OUT ⎟ ⎜ OUT ⎟ ⎜ ⎟ ⎝ R1+R2 ⎠ ⎝ VIN ⎠ ⎝ n ⎠ (2) where 1.7µA is the quiescent current of the LT8640/ LT8640-1 and the second term is the current in the feedback divider reflected to the input of the buck operating at its light load efficiency n. For a 3.3V application with R1 = 1M and R2 = 412k, the feedback divider draws 2.3µA. With VIN = 12V and n = 80%, this adds 0.8µA to the 1.7µA quiescent current resulting in 2.5µA no-load current from the 12V supply. Note that this equation implies that the no-load current is a function of VIN; this is plotted in the Typical Performance Characteristics section. When using large FB resistors, a 4.7pF to 22pF phase-lead capacitor should be connected from VOUT to FB. 8640fa For more information www.linear.com/LT8640 17 LT8640/LT8640-1 Applications Information Setting the Switching Frequency The LT8640/LT8640-1 uses a constant frequency PWM architecture that can be programmed to switch from 200kHz to 3MHz by using a resistor tied from the RT pin to ground. A table showing the necessary RT value for a desired switching frequency is in Table 1. The RT resistor required for a desired switching frequency can be calculated using: RT = 46.5 – 5.2 fSW (3) where RT is in kΩ and fSW is the desired switching frequency in MHz. Table 1. SW Frequency vs RT Value fSW (MHz) RT (kΩ) 0.2 232 0.3 150 0.4 110 0.5 88.7 0.6 71.5 0.7 60.4 0.8 52.3 1.0 41.2 1.2 33.2 1.4 28.0 1.6 23.7 1.8 20.5 2.0 18.2 2.2 15.8 3.0 10.7 Operating Frequency Selection and Trade-Offs Selection of the operating frequency is a trade-off between efficiency, component size, and input voltage range. The advantage of high frequency operation is that smaller inductor and capacitor values may be used. The disadvantages are lower efficiency and a smaller input voltage range. 18 The highest switching frequency (fSW(MAX)) for a given application can be calculated as follows: fSW(MAX) = ( VOUT + VSW(BOT) tON(MIN) VIN – VSW(TOP) + VSW(BOT) ) (4) where VIN is the typical input voltage, VOUT is the output voltage, VSW(TOP) and VSW(BOT) are the internal switch drops (~0.3V, ~0.15V, respectively at maximum load) and tON(MIN) is the minimum top switch on-time (see the Electrical Characteristics). This equation shows that a slower switching frequency is necessary to accommodate a high VIN/VOUT ratio. For transient operation, VIN may go as high as the absolute maximum rating of 42V regardless of the RT value, however the LT8640/LT8640-1 will reduce switching frequency as necessary to maintain control of inductor current to assure safe operation. The LT8640/LT8640-1 is capable of a maximum duty cycle of approximately 99%, and the VIN-to-VOUT dropout is limited by the RDS(ON) of the top switch. In this mode the LT8640/LT8640-1 skips switch cycles, resulting in a lower switching frequency than programmed by RT. For applications that cannot allow deviation from the programmed switching frequency at low VIN/VOUT ratios use the following formula to set switching frequency: VIN(MIN) = VOUT + VSW(BOT) 1– fSW • tOFF(MIN) – VSW(BOT) + VSW(TOP) (5) where VIN(MIN) is the minimum input voltage without skipped cycles, VOUT is the output voltage, VSW(TOP) and VSW(BOT) are the internal switch drops (~0.3V, ~0.15V, respectively at maximum load), fSW is the switching frequency (set by RT), and tOFF(MIN) is the minimum switch off-time. Note that higher switching frequency will increase the minimum input voltage below which cycles will be dropped to achieve higher duty cycle. 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Applications Information Inductor Selection and Maximum Output Current The LT8640/LT8640-1 is designed to minimize solution size by allowing the inductor to be chosen based on the output load requirements of the application. During overload or short-circuit conditions the LT8640/LT8640-1 safely tolerates operation with a saturated inductor through the use of a high speed peak-current mode architecture. A good first choice for the inductor value is: L= VOUT + VSW(BOT) fSW (6) where fSW is the switching frequency in MHz, VOUT is the output voltage, VSW(BOT) is the bottom switch drop (~0.15V) and L is the inductor value in µH. To avoid overheating and poor efficiency, an inductor must be chosen with an RMS current rating that is greater than the maximum expected output load of the application. In addition, the saturation current (typically labeled ISAT) rating of the inductor must be higher than the load current plus 1/2 of in inductor ripple current: 1 IL(PEAK) =ILOAD(MAX) + ΔIL 2 The LT8640/LT8640-1 limits the peak switch current in order to protect the switches and the system from overload faults. The top switch current limit (ILIM) is 10A at low duty cycles and decreases linearly to 7A at DC = 0.8. The inductor value must then be sufficient to supply the desired maximum output current (IOUT(MAX)), which is a function of the switch current limit (ILIM) and the ripple current. (7) where ∆IL is the inductor ripple current as calculated in Equation 9 and ILOAD(MAX) is the maximum output load for a given application. As a quick example, an application requiring 3A output should use an inductor with an RMS rating of greater than 3A and an ISAT of greater than 4A. During long duration overload or short-circuit conditions, the inductor RMS rating requirement is greater to avoid overheating of the inductor. To keep the efficiency high, the series resistance (DCR) should be less than 0.04Ω, and the core material should be intended for high frequency applications. IOUT(MAX) =ILIM – ΔIL 2 (8) The peak-to-peak ripple current in the inductor can be calculated as follows: ΔIL = ⎞ VOUT ⎛ V • ⎜ 1– OUT ⎟ L • fSW ⎝ VIN(MAX) ⎠ (9) where fSW is the switching frequency of the LT8640/ LT8640-1, and L is the value of the inductor. Therefore, the maximum output current that the LT8640/LT86401 will deliver depends on the switch current limit, the inductor value, and the input and output voltages. The inductor value may have to be increased if the inductor ripple current does not allow sufficient maximum output current (IOUT(MAX)) given the switching frequency, and maximum input voltage used in the desired application. In order to achieve higher light load efficiency, more energy must be delivered to the output during the single small pulses in Burst Mode operation such that the LT8640/ LT8640-1 can stay in sleep mode longer between each pulse. This can be achieved by using a larger value inductor (i.e., 4.7µH), and should be considered independent of switching frequency when choosing an inductor. For example, while a lower inductor value would typically be used for a high switching frequency application, if high light load efficiency is desired, a higher inductor value should be chosen. See curve in Typical Performance Characteristics. 8640fa For more information www.linear.com/LT8640 19 LT8640/LT8640-1 Applications Information The optimum inductor for a given application may differ from the one indicated by this design guide. A larger value inductor provides a higher maximum load current and reduces the output voltage ripple. For applications requiring smaller load currents, the value of the inductor may be lower and the LT8640/LT8640-1 may operate with higher ripple current. This allows use of a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. Be aware that low inductance may result in discontinuous mode operation, which further reduces maximum load current. For more information about maximum output current and discontinuous operation, see Linear Technology’s Application Note 44. For duty cycles greater than 50% (VOUT/VIN > 0.5), a minimum inductance is required to avoid sub-harmonic oscillation. See Application Note 19. Input Capacitors The VIN of the LT8640/LT8640-1 should be bypassed with at least three ceramic capacitors for best performance. Two small ceramic capacitors of 1µF should be placed close to the part; one at the VIN1/GND1 pins and a second at VIN2/ GND2 pins. These capacitors should be 0402 or 0603 in size. For automotive applications requiring 2 series input capacitors, two small 0402 or 0603 may be placed at each side of the LT8640/LT8640-1 near the VIN1/GND1 and VIN2/GND2 pins. A third, larger ceramic capacitor of 2.2µF or larger should be placed close to VIN1 or VIN2. See layout section for more detail. X7R or X5R capacitors are recommended for best performance across temperature and input voltage variations. Note that larger input capacitance is required when a lower switching frequency is used. If the input power source has high impedance, or there is significant inductance due to long wires or cables, additional bulk capacitance may be necessary. This can be provided with a low performance electrolytic capacitor. 20 A ceramic input capacitor combined with trace or cable inductance forms a high quality (under damped) tank circuit. If the LT8640/LT8640-1 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the LT8640/LT8640-1’s voltage rating. This situation is easily avoided (see Linear Technology Application Note 88). Output Capacitor and Output Ripple The output capacitor has two essential functions. Along with the inductor, it filters the square wave generated by the LT8640/LT8640-1 to produce the DC output. In this role it determines the output ripple, thus low impedance at the switching frequency is important. The second function is to store energy in order to satisfy transient loads and stabilize the LT8640/LT8640-1’s control loop. Ceramic capacitors have very low equivalent series resistance (ESR) and provide the best ripple performance. For good starting values, see the Typical Applications section. Use X5R or X7R types. This choice will provide low output ripple and good transient response. Transient performance can be improved with a higher value output capacitor and the addition of a feedforward capacitor placed between VOUT and FB. Increasing the output capacitance will also decrease the output voltage ripple. A lower value of output capacitor can be used to save space and cost but transient performance will suffer and may cause loop instability. See the Typical Applications in this data sheet for suggested capacitor values. When choosing a capacitor, special attention should be given to the data sheet to calculate the effective capacitance under the relevant operating conditions of voltage bias and temperature. A physically larger capacitor or one with a higher voltage rating may be required. 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Applications Information Ceramic Capacitors Ceramic capacitors are small, robust and have very low ESR. However, ceramic capacitors can cause problems when used with the LT8640/LT8640-1 due to their piezoelectric nature. When in Burst Mode operation, the LT8640/LT8640-1’s switching frequency depends on the load current, and at very light loads the LT8640/LT86401 can excite the ceramic capacitor at audio frequencies, generating audible noise. Since the LT8640/LT8640-1 operates at a lower current limit during Burst Mode operation, the noise is typically very quiet to a casual ear. If this is unacceptable, use a high performance tantalum or electrolytic capacitor at the output. Low noise ceramic capacitors are also available. A final precaution regarding ceramic capacitors concerns the maximum input voltage rating of the LT8640/LT8640-1. As previously mentioned, a ceramic input capacitor combined with trace or cable inductance forms a high quality (underdamped) tank circuit. If the LT8640/LT8640-1 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the LT8640/ LT8640-1’s rating. This situation is easily avoided (see Linear Technology Application Note 88). Enable Pin The LT8640/LT8640-1 is in shutdown when the EN pin is low and active when the pin is high. The rising threshold of the EN comparator is 1.0V, with 40mV of hysteresis. The EN pin can be tied to VIN if the shutdown feature is not used, or tied to a logic level if shutdown control is required. Adding a resistor divider from VIN to EN programs the LT8640/LT8640-1 to regulate the output only when VIN is above a desired voltage (see the Block Diagram). Typically, this threshold, VIN(EN), is used in situations where the input supply is current limited, or has a relatively high source resistance. A switching regulator draws constant power from the source, so source current increases as source voltage drops. This looks like a negative resistance load to the source and can cause the source to current limit or latch low under low source voltage conditions. The VIN(EN) threshold prevents the regulator from operating at source voltages where the problems might occur. This threshold can be adjusted by setting the values R3 and R4 such that they satisfy the following equation: ⎛ R3 ⎞ VIN(EN) = ⎜ +1⎟ •1.0V ⎝ R4 ⎠ (10) where the LT8640/LT8640-1 will remain off until VIN is above VIN(EN). Due to the comparator’s hysteresis, switching will not stop until the input falls slightly below VIN(EN). When operating in Burst Mode operation for light load currents, the current through the VIN(EN) resistor network can easily be greater than the supply current consumed by the LT8640/LT8640-1. Therefore, the VIN(EN) resistors should be large to minimize their effect on efficiency at low loads. INTVCC Regulator An internal low dropout (LDO) regulator produces the 3.4V supply from VIN that powers the drivers and the internal bias circuitry. The INTVCC can supply enough current for the LT8640/LT8640-1’s circuitry and must be bypassed to ground with a minimum of 1µF ceramic capacitor. Good bypassing is necessary to supply the high transient currents required by the power MOSFET gate drivers. To improve efficiency the internal LDO can also draw current from the BIAS pin when the BIAS pin is at 3.1V or higher. Typically the BIAS pin can be tied to the output of the LT8640/LT8640-1, or can be tied to an external supply of 3.3V or above. If BIAS is connected to a supply other than VOUT, be sure to bypass with a local ceramic capacitor. If the BIAS pin is below 3.0V, the internal LDO will consume current from VIN. Applications with high input voltage and high switching frequency where the internal LDO pulls current from VIN will increase die temperature because of the higher power dissipation across the LDO. Do not connect an external load to the INTVCC pin. 8640fa For more information www.linear.com/LT8640 21 LT8640/LT8640-1 Applications Information Output Voltage Tracking and Soft-Start The LT8640/LT8640-1 allows the user to program its output voltage ramp rate by means of the TR/SS pin. An internal 1.9µA pulls up the TR/SS pin to INTVCC. Putting an external capacitor on TR/SS enables soft starting the output to prevent current surge on the input supply. During the soft-start ramp the output voltage will proportionally track the TR/SS pin voltage. For output tracking applications, TR/SS can be externally driven by another voltage source. From 0V to 0.97V, the TR/SS voltage will override the internal 0.97V reference input to the error amplifier, thus regulating the FB pin voltage to that of TR/SS pin. When TR/SS is above 0.97V, tracking is disabled and the feedback voltage will regulate to the internal reference voltage. The TR/SS pin may be left floating if the function is not needed. An active pull-down circuit is connected to the TR/SS pin which will discharge the external soft-start capacitor in the case of fault conditions and restart the ramp when the faults are cleared. Fault conditions that clear the soft-start capacitor are the EN/UV pin transitioning low, VIN voltage falling too low, or thermal shutdown. Output Power Good When the LT8640/LT8640-1’s output voltage is within the ±8% window of the regulation point, the output voltage is considered good and the open-drain PG pin goes high impedance and is typically pulled high with an external resistor. Otherwise, the internal pull-down device will pull the PG pin low. To prevent glitching both the upper and lower thresholds include 0.2% of hysteresis. The PG pin is also actively pulled low during several fault conditions: EN/UV pin is below 1V, INTVCC has fallen too low, VIN is too low, or thermal shutdown. control. Second, the bottom switch current is monitored such that if inductor current is beyond safe levels switching of the top switch will be delayed until such time as the inductor current falls to safe levels. Frequency foldback behavior depends on the state of the SYNC pin: If the SYNC pin is low the switching frequency will slow while the output voltage is lower than the programmed level. If the SYNC pin is connected to a clock source, floated or tied high, the LT8640/LT8640-1 will stay at the programmed frequency without foldback and only slow switching if the inductor current exceeds safe levels. There is another situation to consider in systems where the output will be held high when the input to the LT8640/ LT8640-1 is absent. This may occur in battery charging applications or in battery-backup systems where a battery or some other supply is diode ORed with the LT8640/LT8640-1’s output. If the VIN pin is allowed to float and the EN pin is held high (either by a logic signal or because it is tied to VIN), then the LT8640/LT8640-1’s internal circuitry will pull its quiescent current through its SW pin. This is acceptable if the system can tolerate several µA in this state. If the EN pin is grounded the SW pin current will drop to near 1µA. However, if the VIN pin is grounded while the output is held high, regardless of EN, parasitic body diodes inside the LT8640/LT8640-1 can pull current from the output through the SW pin and the VIN pin. Figure 5 shows a connection of the VIN and EN/UV pins that will allow the LT8640/LT8640-1 to run only when the input voltage is present and that protects against a shorted or reversed input. D1 VIN Shorted and Reversed Input Protection The LT8640/LT8640-1 will tolerate a shorted output. Several features are used for protection during output short-circuit and brownout conditions. The first is the switching frequency will be folded back while the output is lower than the set point to maintain inductor current 22 VIN LT8640/ LT8640-1 EN/UV GND 8640 F05 Figure 5. Reverse VIN Protection 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Applications Information Thermal Considerations and Peak Output Current For higher ambient temperatures, care should be taken in the layout of the PCB to ensure good heat sinking of the LT8640/LT8640-1. The ground pins on the bottom of the package should be soldered to a ground plane. This ground should be tied to large copper layers below with thermal vias; these layers will spread heat dissipated by the LT8640/LT8640-1. Placing additional vias can reduce thermal resistance further. The maximum load current should be derated as the ambient temperature approaches the maximum junction rating. Power dissipation within the LT8640/LT8640-1 can be estimated by calculating the total power loss from an efficiency measurement and subtracting the inductor loss. The die temperature is calculated by multiplying the LT8640/LT8640-1 power dissipation by the thermal resistance from junction to ambient. The internal overtemperature protection monitors the junction temperature of the LT8640/LT8640-1. If the junction temperature reaches approximately 170°C, the LT8640/ 60 DC2202A DEMO BOARD VIN = 12V VOUT = 5V fSW = 2MHz STANDBY LOAD = 0.25A PULSED LOAD = 7A 80 50 40 30 20 10 0 The LT8640/LT8640-1’s internal power switches are capable of safely delivering up to 7A of peak output current. However, due to thermal limits, the package can only handle 7A loads for short periods of time. This time is determined by how quickly the case temperature approaches the maximum junction rating. Figure 6 shows an example of how case temperature rise changes with the duty cycle of a 1kHz pulsed 7A load. 90 DC2202A DEMO BOARD VIN = 12V, fSW = 1MHz VIN = 24V, fSW = 1MHz VIN = 12V, fSW = 2MHz VIN = 24V, fSW = 2MHz 70 Temperature rise of the LT8640/LT8640-1 is worst when operating at high load, high VIN, and high switching frequency. If the case temperature is too high for a given application, then either VIN, switching frequency, or load current can be decreased to reduce the temperature to an acceptable level. Figure 6 shows examples of how case temperature rise can be managed by reducing VIN, switching frequency, or load. CASE TEMPERATURE RISE (°C) CASE TEMPERATURE RISE (°C) 80 LT8640-1 will stop switching and indicate a fault condition until the temperature drops about 10°C cooler. 70 60 50 40 30 20 10 0 1 2 3 LOAD CURRENT (A) 4 0 5 0.2 0.4 0.6 DUTY CYCLE OF 7A LOAD 0.8 8640 F07 8640 F06 Figure 6. Case Temperature Rise 0 Figure 7. Case Temperature Rise vs 7A Pulsed Load 8640fa For more information www.linear.com/LT8640 23 LT8640/LT8640-1 Typical Applications 5V 5A Step-Down Converter VIN 5.5V TO 42V 4.7µF EN/UV VIN1 1µF 0603 GND1 PG 10nF VIN2 1µF 0603 GND2 LT8640/ LT8640-1 BST SYNC/MODE TR/SS 0.1µF 3.3µH 1µF 4.7pF 1M FB INTVCC 41.2k VOUT 5V 5A SW BIAS RT 243k GND fSW = 1MHz L: VISHAY IHLP2525EZ-01 47µF 1210 X7R 8640 TA08 3.3V, 5A Step-Down Converter VIN 3.8V TO 42V 4.7µF EN/UV VIN1 1µF 0603 GND1 PG 10nF VIN2 GND2 LT8640/ LT8640-1 BST SYNC/MODE TR/SS 0.1µF 2.2µH VOUT 3.3V 5A SW BIAS 1µF 4.7pF 1M FB INTVCC 41.2k 1µF 0603 RT 412k GND fSW = 1MHz L: VISHAY IHLP2525EZ-01 47µF 1210 X7R 8640 TA05 Ultralow EMI 5V, 5A Step-Down Converter VIN 5.6V TO 42V FB1 BEAD L2 6.8µH 10µF 1210 10µF 1210 10µF 1206 1µF 0603 EN/UV VIN1 GND1 PG 10nF VIN2 GND2 LT8640/ LT8640-1 BST SYNC/MODE TR/SS 0.1µF 1.5µH 4.7pF INTVCC RT 1M FB GND fSW = 2MHz FB1 BEAD: WE-MPSB 100Ω 8A 1812 L: WE-LHMI7030 L2: COILCRAFT XAL6060 24 VOUT 5V 5A SW BIAS 1µF 18.2k 1µF 0603 243k 47µF 1210 X7R 8640 TA02 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Typical Applications 2MHz 5V, 5A Step-Down Converter VIN 5.5V TO 42V 4.7µF EN/UV VIN1 1µF 0603 GND1 PG 10nF VIN2 GND2 LT8640/ LT8640-1 BST SYNC/MODE TR/SS 0.1µF 1.5µH VOUT 5V 5A SW BIAS 1µF 4.7pF 1M FB INTVCC 18.2k 1µF 0603 RT 243k GND fSW = 2MHz L: VISHAY IHLP2525CZ-01 47µF 1210 X7R 8640 TA03 2MHz 3.3V, 5A Step-Down Converter VIN 3.8V TO 42V 4.7µF EN/UV VIN1 1µF 0603 GND1 PG 10nF VIN2 GND2 LT8640/ LT8640-1 BST SYNC/MODE TR/SS 0.1µF 1µH VOUT 3.3V 5A SW BIAS 1µF 4.7pF 1M FB INTVCC 18.2k 1µF 0603 RT 412k GND fSW = 2MHz L: VISHAY IHLP2525CZ-01 47µF 1210 X7R 8640 TA06 12V, 5A Step-Down Converter VIN 12.5V TO 42V 4.7µF EN/UV VIN1 1µF 0603 GND1 PG 10nF VIN2 GND2 LT8640/ LT8640-1 BST SYNC/MODE TR/SS 0.1µF 4.7µH 4.7pF INTVCC RT VOUT 12V 5A SW BIAS 1µF 41.2k 1µF 0603 1M FB GND fSW = 1MHz L: VISHAY IHLP2525EZ-01 47µF 1210 88.7k 8640 TA04 8640fa For more information www.linear.com/LT8640 25 LT8640/LT8640-1 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UDC Package 18-Lead Plastic QFN (3mm × 4mm) (Reference LTC DWG # 05-08-1956 Rev B) Exposed Pad Variation AA 0.055 BSC 0.70 ±0.05 3.50 ±0.05 2.10 ±0.05 1.50 REF 0.770 BSC 0.220 ±0.05 0.356 ±0.05 0.400 ±0.05 PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC 2.50 REF 3.10 ±0.05 4.50 ±0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 3.00 ±0.10 0.75 ±0.05 1.50 REF PIN 1 ID 0.12 × 45° 0.40 ±0.10 1 PIN 1 TOP MARK (NOTE 5) 4.00 ±0.10 0.220 ±0.05 2.127 ±0.10 2 2.50 REF 0.770 BSC 0.356 ±0.05 0.400 ±0.05 (UDC18) QFN 1213 REV B 0.200 REF 0.00 – 0.05 R = 0.110 TYP 0.25 ±0.05 0.50 BSC BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 26 8640fa For more information www.linear.com/LT8640 LT8640/LT8640-1 Revision History REV DATE DESCRIPTION A 10/15 Added LT8640-1 Version to Title PAGE NUMBER Clarified Minimum On-Time to 35ns Added LT8640-1 Version All 1, 3 1, 2, 4 Clarified SYNC/MODE Threshold 3 Added LT8640-1 Version Specifications 4 Clarified Minimum Load Graph to Pulse Skipping 7 Added LT8640-1 Version 11 to 25 8640fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. For more information www.linear.com/LT8640 27 LT8640/LT8640-1 Typical Applications VIN 3.4V TO 22V (42V TRANSIENT) 2MHz 1.8V, 5A Step-Down Converter 4.7µF EN/UV VIN1 1µF 0603 GND1 PG 10nF VIN2 GND2 LT8640/ LT8640-1 BST SYNC/MODE TR/SS SW BIAS 1µF 18.2k INTVCC RT FB 1µF 0603 0.1µF 1µH EXTERNAL 1µF SOURCE >3.1V OR GND VOUT 1.8V 5A 10pF 866k 100µF 1210 1M GND fSW = 2MHz L: VISHAY IHLP2525CZ-01 8640 TA07 Related Parts PART DESCRIPTION COMMENTS LT8609 42V, 2A, 94% Efficiency, 2.2MHz Synchronous MicroPower Step-Down DC/DC Converter with IQ = 2.5µA VIN(MIN) = 3V, VIN(MAX) = 42V, VOUT(MIN) = 0.8V, IQ = 2.5µA, ISD < 1µA, MSOP-10E LT8610A/AB 42V, 3.5A, 96% Efficiency, 2.2MHz Synchronous MicroPower StepDown DC/DC Converter with IQ = 2.5µA VIN(MIN) = 3.4V, VIN(MAX) = 42V, VOUT(MIN) = 0.97V, IQ = 2.5µA, ISD < 1µA, MSOP-16E LT8610AC 42V, 3.5A, 96% Efficiency, 2.2MHz Synchronous MicroPower StepDown DC/DC Converter with IQ = 2.5µA VIN(MIN) = 3V, VIN(MAX) = 42V, VOUT(MIN) = 0.8V, IQ = 2.5µA, ISD < 1µA, MSOP-16E LT8610 42V, 2.5A, 96% Efficiency, 2.2MHz Synchronous MicroPower StepDown DC/DC Converter with IQ = 2.5µA VIN(MIN) = 3.4V, VIN(MAX) = 42V, VOUT(MIN) = 0.97V, IQ = 2.5µA, ISD < 1µA, MSOP-16E LT8611 42V, 2.5A, 96% Efficiency, 2.2MHz Synchronous MicroPower StepDown DC/DC Converter with IQ = 2.5µA and Input/Output Current Limit/Monitor VIN(MIN) = 3.4V, VIN(MAX) = 42V, VOUT(MIN) = 0.97V, IQ = 2.5µA, ISD < 1µA, 3mm × 5mm QFN-24 LT8616 42V, Dual 2.5A + 1.5A, 95% Efficiency, 2.2MHz Synchronous MicroPower Step-Down DC/DC Converter with IQ = 5µA VIN(MIN) = 3.4V, VIN(MAX) = 42V, VOUT(MIN) = 0.8V, IQ = 5µA, ISD < 1µA, TSSOP-28E, 3mm × 6mm QFN-28 LT8620 65V, 2.5A, 94% Efficiency, 2.2MHz Synchronous MicroPower StepDown DC/DC Converter with IQ = 2.5µA VIN(MIN) = 3.4V, VIN(MAX) = 65V, VOUT(MIN) = 0.97V, IQ = 2.5µA, ISD < 1µA, MSOP-16E, 3mm × 5mm QFN-24 LT8614 42V, 4A, 96% Efficiency, 2.2MHz Synchronous Silent Switcher StepDown DC/DC Converter with IQ = 2.5µA VIN(MIN) = 3.4V, VIN(MAX) = 42V, VOUT(MIN) = 0.97V, IQ = 2.5µA, ISD < 1µA, 3mm × 4mm QFN18 LT3975 42V, 2.5A, High Efficiency, 2MHz MicroPower Step-Down DC/DC Converter with IQ = 2.7uA VIN(MIN) = 4.3V, VIN(MAX) = 42V, VOUT(MIN) = 1.2V, IQ = 2.7µA, ISD < 1µA, MSOP-16E LT3976 40V, 5A, High Efficiency, 2MHz MicroPower Step-Down DC/DC Converter with IQ = 3.3uA VIN(MIN) = 4.3V, VIN(MAX) = 40V, VOUT(MIN) = 1.2V, IQ = 3.3µA, ISD < 1µA, MSOP-16E LT8612 42V, 6A, 96% Efficiency, 2.2MHz Synchronous MicroPower Step-Down DC/DC Converter with IQ = 2.5µA VIN(MIN) = 3.4V, VIN(MAX) = 42V, VOUT(MIN) = 0.97V, IQ = 3.0µA, ISD < 1µA, 3mm × 6mm QFN-28 LT8613 42V, 6A, 96% Efficiency, 2.2MHz Synchronous MicroPower StepDown DC/DC Converter with Current Limiting VIN(MIN) = 3.4V, VIN(MAX) = 42V, VOUT(MIN) = 0.97V, IQ = 3.0µA, ISD < 1µA, 3mm × 6mm QFN-28 LT8602 42V, Quad Output (2.5A + 1.5A + 1.5A + 1.5A) 95% Efficiency, 2.2MHz Synchronous MicroPower Step-Down DC/DC Converter with IQ = 25µA VIN(MIN) = 3V, VIN(MAX) = 42V, VOUT(MIN) = 0.8V, IQ = 2.5µA, ISD < 1µA, 6mm × 6mm QFN-40 28 8640fa Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LT8640 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com/LT8640 LT 1015 • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2015