Toggles Series MS Rockers General Specifications Electrical Capacity (Resistive Load) Pushbuttons Other Ratings Programmable Illuminated PB Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Contact Timing: Total Travel: Keylocks Materials & Finishes Actuator: Frame: Case: Movable Contacts: Stationary Contacts: Terminals: Rotaries Slides Tactiles Power Level: H Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Tilt Processing Touch Miniature Illuminated Slides Soldering Time & Temp: Cleaning: Standards & Certifications Flammability Standards: 10 milliohms maximum 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum Nonshorting (break-before-make) .087” (2.2mm) Polyamide (UL94V-0) Stainless steel Glass fiber reinforced diallyl phthalate resin (UL94V-0) Silver alloy Silver capped copper with silver plating Copper or brass with silver plating –10°C through +55°C (+14°F through +131°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering Recommended (PC version): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Note: Lever must be in center position while soldering. These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 rated actuator & case Supplement Accessories Indicators 6A @ 125V AC or 3A @ 250V AC H38 www.nkk.com Toggles Series MS Miniature Illuminated Slides Rockers Distinctive Characteristics Pushbuttons Bright, LED illumination at top of actuator. Programmable Illuminated PB Over-center actuator block and plunger design gives crisp actuation, diminishes sparking, and increases operating life. Guide interlocked with actuator block prevents window locking and maintains correct plunger alignment to assure contact stability. High internal barriers between poles and insulating sheet between case and actuator block give added protection to contacts. H Tactiles Prominent external insulating barriers increase insulation resistance and dielectric strength. Slides Rotaries Keylocks Antijamming design protects contacts from damage due to excessive downward force on the actuator. Actual Size Supplement Accessories Indicators Clinching of frame to case well above base and terminals provides 1,500V dielectric strength. Touch Tilt Epoxy sealed terminals prevent entry of flux, solvents, and other contaminants. www.nkk.com H39 Series MS Toggles Miniature Illuminated Slides TYPICAL SWITCH ORDERING EXAMPLE Pushbuttons Rockers MS 1 2 Programmable Illuminated PB Poles 1 L F W L LED Lighted Mounting 2 ON NONE ON 3 ON OFF ON Rotaries Keylocks LEDS Silver; Rated 6A @ 125V AC & 3A @ 250V AC W Circuits C Contact Materials & Ratings Illumination SPDT 01 C Red E Yellow F Green Terminals N For Straight PC (Terminal 03 only) F With 2-screw Flange (Terminal 01 only) 01 Solder Lug 03 Straight PC DESCRIPTION FOR TYPICAL ORDERING EXAMPLE H Red LED Illumination 2-screw Flange Frame Silver Contacts with 6-Amp Rating Tactiles Slides MS12LFW01C SPDT ON-NONE-ON Circuit Tilt Solder Lug Terminals Slide Position Pole SP Supplement Connected Terminals Left Center Right MS12 ON NONE ON MS13 ON OFF ON Left Center Throw & Schematics Right Model Accessories Indicators Touch POLES & CIRCUITS Note: Terminal numbers are not actually on the switch. LED circuit is isolated and requires an external connection. 2 (COM) 2-1 OPEN 2-3 SPDT L(+) 1 3 4 CONTACT MATERIALS & RATINGS W H40 Silver over Silver Power Level www.nkk.com 6A @ 125V AC & 3A @ 250V AC L(-) 6 Series MS Toggles Miniature Illuminated Slides 03 2-screw Flange (Combines with Solder Lug Terminal 01 only) 01 Straight PC (6.35) (4.8) .250 .189 Epoxy Seal (1.17) Typ .046 (2.0) .079 (4.0) .157 Epoxy Seal Solder Lug Pushbuttons (4.8) .189 Thk = (0.8) Typ .031 (6.35) (4.8) .250 .189 Programmable Illuminated PB F Straight PC Mount (Combines with Straight PC Terminal 03 only) (2.0) .079 (1.1) .043 (1.17) .046 (4.8) .189 Thk = (0.8) Typ .031 LED COLORS & SPECIFICATIONS Color (-) C E Red Yellow F Green Keylocks (+) Maximum Forward Current IFM 30mA 30mA 25mA Typical Forward Current IF 16mA 16mA 16mA Forward Voltage VF 1.98V 2.06V 2.16V Maximum Reverse Voltage VRM 5V 5V 5V Current Reduction Rate Above 25°C ∆IF 0.40mA/°C 0.42mA/°C 0.33mA/°C Ambient Temperature Range Rotaries LEDs are supplied as an integral part of the switch (not available separately). The lamp circuit is independent of switch operation. Electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula given in the Supplement. –15° ~ +60°C H TYPICAL SWITCH DIMENSIONS Slides N Rockers MOUNTING TYPES & TERMINALS (2.0) Typ .079 (6.1) .240 (8.2) .323 (5.1) .201 (12.7) .500 2 (4.7) Typ .185 (17.53) .690 1 4 (0.5) .020 (4.8) .189 (11.9) .469 (0.4) (4.5) .016 .177 (7.6) (6.35) .299 .250 (6.8) .268 (9.0) .354 Maximum Panel Thickness .197” (5.0mm) Actuator in LEFT Position Tilt (3.8) .150 Direction of Actuation 3 6 (17.53) .690 (19.6) .772 (2.0) .079 (2.4) .094 Dia Typ MS12LFW01C Straight PC Terminals (1.17) Typ .046 (0.8) Typ .031 (3.8) .150 (2.0) .079 (8.2) .323 (4.7) Typ .185 (5.1) .201 (7.6) .299 (4.8) .189 (6.35) .250 Actuator in LEFT Position 3 3 2 (12.7) .500 (4.8) .189 (11.9) .469 (4.7) Typ .185 1 1 4 6 2 (0.5) .020 (6.8) .268 4 (1.8) Dia Typ .073 (9.0) .354 Direction of Actuation 6 (4.8) .189 Maximum Panel Thickness .197” (5.0mm) www.nkk.com Accessories Circuit Mark This Side (5.0) .197 Touch (1.17) Typ .046 (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 Indicators Circuit Mark This Side MS12LNW03C H41 Supplement (5.0) .197 Tactiles Solder Lug Terminals (1.2) R Typ .047