Rockers Toggles Series B A Subminiature Fully Illuminated Toggles General Specifications Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Electrical Capacity (Resistive Load) Logic Level: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: 50 milliohms maximum Insulation Resistance: 500 megohms minimum @ 500V DC Dielectric Strength: 500V AC minimum for 1 minute minimum Mechanical Life: 100,000 operations minimum Electrical Life: 50,000 operations minimum Nominal Operating Force:1.18N Contact Timing: Nonshorting (break-before-make) Angle of Throw: 26° Materials & Finishes Actuator: Bushing Housing: Case Housing: Support Bracket: Movable Contact: Stationary Contacts: Terminals: Operating Temperature Range: Humidity: Vibration: Shock: –25°C through +55°C (–13°F through +131°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 5 minutes; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 3 right angled directions, with 5 shocks in each direction) Tilt Tactiles Environmental Data Polyamide Polyamide Glass fiber reinforced polyamide Phosphor bronze with tin plating Phosphor bronze with gold plating Brass with tin plating Brass with gold plating Soldering: Cleaning: Wave Soldering recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Automated alcohol based cleaning recommended, 5 minutes maximum. Do not use high-purity alcohol (50% alcohol or more) or organic solvent. High alcohol solution can damage clear plastic. See Cleaning specifications in Supplement section. Standards & Certifications The B Series illuminated toggles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. Supplement Accessories Indicators Touch PCB Processing A20 www.nkk.com A Rockers Distinctive Characteristics Toggles Series B Subminiature Fully Illuminated Toggles Programmable Illuminated PB Pushbuttons LED provides maximum illumination to bushing and actuator, indicating actuator status in highly visible green, red, or amber for single color or red/green for bicolor. (Patent pending.) Totally sealed body construction prevents contact contamination and allows time- and money-saving automated soldering and cleaning. Molded-in, epoxy sealed terminals lock out flux and other contaminants. Rotaries Keylocks Award-winning STC contact mechanism with benefits unavailable in conventional mechanisms: smoother, positive detent actuation, increased contact stability, and unparalleled logic-level reliability. (Additional STC details in Terms & Acronyms; see Supplement section.) Touch Tilt Tactiles Slides .100” x .100” (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing. Supplement Accessories Indicators Actual Size www.nkk.com A21 TYPICAL SWITCH ORDERING EXAMPLE B Pushbuttons 1 Poles 1 2 J ON J NONE J ON ON OFF ON Combines with bicolor LED only C PC Terminals Clear Combines with single color or bicolor LEDs 3 P Actuator Circuits 2 SPDT LEDs P Straight H Right Angle C Red V Vertical D Amber F Green Single Color ON-NONE-ON only Bushing J Bicolor Clear CF Red/Green ON-NONE-ON & ON-OFF-ON Keylocks Programmable Illuminated PB Subminiature Fully Illuminated Toggles A Rockers Toggles Series B DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Rotaries B12JJPC Clear Toggle & Bushing with Red LED Slides SPDT ON-NONE-ON Circuit Tactiles Straight PC Terminals POLE & CIRCUITS Up Pole Model Throw Center Connected Terminals Down SPDT Throw & Schematics Up Center Down Note: Terminal numbers are not actually on the switch. LED circuit is isolated and requires an external power source. Slot Slot B12 ON NONE ON 2-3 NONE 2-1 B13 ON OFF ON 2-3 OPEN 2-1 2 (COM) 3 (4) Red (5) (6) ACTUATOR & BUSHING J (6.3) .248 Supplement J 26° Clear Toggle (1.9) Dia .075 (3.5) .138 A22 www.nkk.com (5) (6) Green 1 Single Color Accessories Indicators Touch Tilt Toggle Position Clear Bushing Bicolor A LED COLORS & SPECIFICATIONS Colors Bicolor C D F CF Red Amber Green Red/Green Rockers Single Color I FM 30mA 30mA 25mA 30mA/25mA Typical Forward Current IF 20mA 20mA 20mA 20mA/20mA Forward Voltage VF 1.95V 2.0V 3.3V 1.95V/3.3V Maximum Reverse Voltage VRM 5V 5V 5V 5V/5V 0.33mA/°C 0.40mA/°C/0.33mA/°C Current Reduction Rate Above 25°C ∆I F 0.40mA/°C Ambient Temperature Range Pushbuttons Maximum Forward Current –25°C ~ +55°C PC TERMINALS H Straight V Right Angle with Bracket Vertical with Bracket Keylocks P TYPICAL SWITCH DIMENSIONS Straight PC 26° (8.8) .346 (0.8) .031 (13.1) .516 3 6 (8.8) .346 4 1 5 2 6 3 (0.8) Dia Typ .031 (2.54) Typ .100 (3.1) .122 5 Slides (3.5) .138 (6.3) .248 4 2 (5.08) .200 Terminal 4 is a support pin on single color models. B12JJPC Right Angle PC 26° 1 6 5 4 (8.8) .346 (2.54) Typ .100 1 2 3 4 5 6 (5.08) .200 (5.08) .200 (16.42) .646 (2.54) .100 (0.5) .020 (0.8) Dia Typ .031 (0.6) Dia Typ .024 (2.54) Typ .100 Terminal 4 is a support pin on single color models. 26° (3.1) .122 1 4 2 5 3 6 (8.8) .346 Slot (0.6) Typ .024 (5.08) .200 (8.8) .346 (2.7) .106 (6.3) .248 B13JJHCF Vertical PC (1.9) Dia .075 (6.0) Dia .236 Touch (0.4) .016 (2.54) .100 Tilt 2 Slot (2.7) .106 (6.3) .248 (5.08) .200 (8.8) .346 3 (0.4) .016 (5.08) .200 (18.96) .746 (5.08) .200 4 1 5 2 6 3 (2.54) Typ .100 Accessories (0.6) Typ .024 (1.9) Dia .075 (3.1) .122 (5.08) .200 (0.5) Typ .020 (2.54) Typ .100 (5.08) .200 (0.6) Dia Typ .024 (0.8) Dia Typ .031 Terminal 4 is a support pin on single color models. www.nkk.com Supplement (6.0) Dia .236 Tactiles Slot 1 (5.08) .200 (2.54) Typ .100 Rotaries (0.6) Dia Typ .024 Indicators (1.9) Dia .075 (6.0) Dia .236 Programmable Illuminated PB LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Toggles Series B Subminiature Fully Illuminated Toggles B13JJVCF A23