A Rockers GENERAL SPECIFICATIONS FOR S100s Electrical Capacity (Resistive & Inductive Load) Power Level: Shown in the following table Pushbuttons Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Operating Temp Range: 10 milliohms maximum 200 megohms minimum @ 500V DC 1,500V AC minimum for 1 minute minimum 30,000 operations minimum 10,000 operations minimum –10°C through +70°C (+14°F through +158°F) Programmable Illuminated PB Materials & Finishes Brass with chrome plating Brass with chrome or nickel plating Phenolic resin Steel with zinc plating Copper with silver plating Silver alloy plus copper with silver plating Copper with silver plating Keylocks Toggle: Bushing: Case: Case Cover: Movable Contactor Plate: Movable & Stationary Contacts: Terminals: Rotaries Toggles Series S Low Capacity Standard Size Toggles Environmental Data Slides Operating Temp Range: –30°C through +70°C (–22°F through +158°F) for Splashproof models; –10°C through +70°C (+14°F through +158°F) for all other models Sealing: Splashproof models meet IP67 standard Installation Mounting Torque: 2.94Nm (26 lb•in) for double nut Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section. Tactiles Standards & Certifications Accessories Indicators Touch Tilt File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” to end of part number to order CSA certified switch. Certified at 5A @ 125V AC & 2A @ 250V AC. Supplement CSA: www.nkk.com A95 Toggles Series S Low Capacity Standard Size Toggles A DOUBLE POLE WITH SOLDER LUG * Rockers * CSA certified only when ordered with marking on switch (see General Specs) *Approvals Down Pole & Throw Model Electrical Capacity Toggle Position/Connected Terminals Center Resistive Up Keyway Inductive AC 125V AC 250V DC 30V AC 125V PF 0.6 Angle of Throw S114 –– DPST ON 2-1 5-4 NONE OFF — 5A 2A 5A 3A 25° S116 –– DPDT ON 2-1 5-4 NONE ON 2-3 5-6 5A 2A 5A 3A 25° S116R –– DPDT ON 2-1 5-4 NONE ON 2-3 5-6 5A 2A 5A 3A 25° Throw & Schematics: –– 2 DPST 1 5 (COM) 2 DPDT 1 4 (COM) 3 4 5 6 Note: Terminal numbers are actually on the switch Notes: Standard Hardware: AT504M Knurled Nut, AT508 Lockwasher, AT527M Backup Hex Nut. See Accessories & Hardware section. Optional Splashproof Boot Assemblies (only for bat lever models): AT401 & AT4181 boots plus hex nut and o-ring. See Accessories & Hardware section. * Wire harness & cable assemblies offered only in Americas. S114 & S116 Keylocks Programmable Illuminated PB Pushbuttons R (2.0) Dia Typ .079 M12 P1 Rotaries Keyway (6.0) Dia .236 Slides (5.5) .217 (18.0) .709 (10.0) .394 (4.0) .157 (2.3) Dia .090 (3.8) Typ .150 (22.9) .902 S116 6 3 5 2 4 1 (12.5) Dia .492 Tactiles Tilt Touch Indicators Accessories www.nkk.com (11.5) .453 (27.8) 1.094 (1.5) .060 (0.8) Typ .031 (4.0) .157 (29.0) 1.142 (0.3) Typ .012 S114 does not have terminals 3 & 6 Supplement A96 (9.0) .354 (10.35) Typ .407 25° (17.6) .693 S116R Black Polyamide Paddle Maximum Panel Thickness: .158” (4.0mm)