A GENERAL SPECIFICATIONS FOR S800s ~ S732 Rockers Electrical Capacity (Resistive & Inductive Load) Pushbuttons Power Level: Shown in the following tables Toggles Series S High Capacity Standard Size Toggles Other Ratings Programmable Illuminated PB Contact Resistance: 10 milliohms maximum Insulation Resistance: 1,000 megohms minimum @ 500V DC Dielectric Strength: 2,000V AC minimum for 1 minute minimum for S800s & S800Ds 3,000V AC minimum for 1 minute minimum for S732 Mechanical Life: 50,000 operations minimum Electrical Life: 10,000 operations minimum for S800Ds 25,000 operations minimum for S800s & S732 Materials & Finishes Slides Rotaries Keylocks Toggle: Brass with nickel plating for S732 Brass with chrome plating for S800s & S800Ds Bushing: Brass with chrome plating Case: Phenolic resin for S732; melamine phenol for S800s Case Cover: Steel with chromate plating over zinc plating Movable Contactor Plate: Copper with silver plating Movable & Stationary Contacts: Silver alloy capped on copper with silver plating Common Terminals:Brass Contact Terminals: Brass with silver or nickel plating Environmental Data Operating Temp Range: –10°C through +70°C (+14°F through +158°F) Tactiles Installation Mounting Torque: 2.94Nm (26 lb•in) for double nut Maximum Panel Thickness: Shown beneath panel cutout in switch dimension drawings Tilt File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” to end of part number to order CSA certified switch. CSA certification designated beside part numbers on following pages. See Supplement section to find CSA rating details. Indicators CSA: Accessories File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” to end of part number to order UL recognized switch. UL or cULus recognition designated beside part numbers on following pages. See Supplement section to find UL or cULus rating details. Supplement UL: Touch Standards & Certifications www.nkk.com A113 A High Capacity Standard Size Toggles DOUBLE POLE WITH SCREW LUG * UL, cULus & CSA recognized only when ordered with marking on switch (see General Specs) Rockers Toggles Series S Down *Approvals Pole & Throw R C US Up Resistive Keyway AC 125V AC 250V DC 30V DC 125V 30A 30A 30A 1A Inductive Motor Load AC 125V AC 250V PF 0.6 PF 0.6 AC 125V Pushbuttons R Center S821 DPST ON 2-3 5-6 NONE S822 DPDT ON 2-3 5-6 NONE ON 2-1 5-4 30A 30A 30A 1A 30A 15A — S823 DPDT ON 2-3 5-6 OFF ON 2-1 5-4 30A 30A 30A 1A 30A 15A — Programmable Illuminated PB Model Electrical Capacity Toggle Position/Connected Terminals Throw & Schematics: 2 DPST (COM) 3 OFF 5 — 2 DPDT 3 6 1 6 750W Note: Terminal numbers are on the switch 4 M4.5x6 Keyway M12 P1 6 3 (12.5) Dia .492 (42.0) 1.654 Keylocks 28° (12.0) Typ .472 5 4 (9.0) .354 2 1 (3.0) Dia .118 (6.1) Dia .240 (12.0) .472 Rotaries Slides Tactiles Tilt 5 15A Notes: Standard Hardware: AT503M Face Hex Nut, AT506M Locking Ring, AT508 Lockwasher, AT527M Backup Hex Nut. See Accessories & Hardware section. Optional Splashproof Boot Assembly: AT401 boot plus hex nut & o-ring. See Accessories & Hardware section. (22.0) .866 (12.0) .472 Maximum Panel Thickness: .177” (4.5mm) (24.0) .945 (34.0) 1.339 S822 S821 does not have terminals 1 & 4 THREE POLE WITH SCREW LUG * UL, cULus & CSA recognized only when ordered with marking on switch (see General Specs) Model Down Pole & Throw R R C US Electrical Capacity Toggle Position/Connected Terminals *Approvals Center Resistive Up Keyway Inductive AC 125V AC 250V DC 30V DC 125V AC 125V PF 0.6 AC 250V PF 0.6 S831 3PST ON 2-3 5-6 8-9 NONE OFF — 30A 30A 30A 1A 30A 15A S832 3PDT ON 2-3 5-6 8-9 NONE ON 2-1 5-4 8-7 30A 30A 30A 1A 30A 15A S833 3PDT ON 2-3 5-6 8-9 OFF ON 2-1 5-4 8-7 30A 30A 1A 30A 15A 2 5 7 Note: Terminal numbers are on the switch Throw & Schematics: Touch (COM) 30A 3PST 3 (COM) 6 8 2 3PDT 9 3 5 1 6 30A (COM) 4 8 9 Notes: Standard Hardware: AT503M Face Hex Nut, AT506M Locking Ring, AT508 Lockwasher, AT527M Backup Hex Nut. See Accessories & Hardware section. Optional Splashproof Boot Assembly: AT401 boot plus hex nut & o-ring. See Accessories & Hardware section. M4.5x6 Keyway Indicators M12 P1 6 3 9 28° (12.0) Typ .472 Accessories (12.5) Dia .492 (42.0) 1.654 5 8 7 2 1 4 (6.1) Dia .240 (9.0) .354 (3.0) Dia .118 Supplement (14.5) Typ .571 (22.0) .866 (12.0) .472 (34.0) 1.339 S833 A114 (43.0) 1.693 S831 does not have terminals 1, 4 & 7 www.nkk.com Maximum Panel Thickness: .177” (4.5mm) A DOUBLE POLE WITH SCREW LUG & FLATTED LEVER US DC 30V S821D DPST ON 2-3 5-6 NONE OFF S822D DPDT ON 2-3 5-6 NONE ON S823D DPDT ON 2-3 5-6 OFF — ON Inductive L/R = 3ms DC 48V DC 125V DC 250V DC 400V DC 24V DC 48V 4A (10A) 15A 10A DC 125V DC 250V 30A 30A 20A 15A 6A 3A 2-1 5-4 30A 30A 20A 15A 4A 15A 10A 6A 3A 2-1 5-4 30A 30A 15A 7.5A — 15A 10A 6A 3A ( ) capacity is due to wiring. Refer to instructions below. Throw & Schematics: 2 (COM) 5 2 DPST (COM) 5 Note: Terminal numbers are on the switch DPDT 3 3 6 1 6 4 Notes: Standard Hardware: AT503M Face Hex Nut, AT506M Locking Ring, AT508 Lockwasher, AT527M Backup Hex Nut. See Accessories & Hardware section. Double Pole Keyway M4.5x6 M12 P1 6 3 (4.0) .157 5 4 2 1 Keylocks (12.5) Dia .492 (42.0) 1.654 28° (12.0) Typ .472 (9.0) .354 (8.15) .321 (3.0) Dia .118 (12.0) .472 (24.0) .945 (34.0) 1.339 Maximum Panel Thickness: .177” (4.5mm) S821D does not have terminals 1 & 4 S822D Slides (27.0) 1.063 Rotaries (12.0) .472 (9.0) .354 400V DC WIRING INSTRUCTIONS Inductive loads produce an arc caused by counter-electromotive force when opening the circuit. Recommend inserting spark elimination circuit. Contact factory for details. Tilt Contact Point D R (2) (3) 4 5 3 6 Contact Connection Position (Patent Pending) 4. Compressed terminal connection When connecting screw terminal with compressed terminal, select compressed terminal using drawing below. Minus Pole Connection ) .8 (9 86 .3 External Connection (5) (6) L + Plus Pole Connection www.nkk.com 1 4 2 5 3 6 Accessories 1 2 C Supplement 2. Wiring for DC400V 10A (9.8) .386 • • 3. Inductive load Middle terminal shall be the minus pole when using DC circuit. Switch case is marked with (+) and (-). Do not store near (5cm) highly magnetic items. If actuation is interrupted when switching from ON to OFF, arcing may continue and switch could be burned. Touch 1. DC switch use • Rockers Resistive Up Pushbuttons R C R Center Keyway Tactiles Pole & Throw Programmable Illuminated PB Down *Approvals Model Electrical Capacity Toggle Position/Connected Terminals Indicators * UL, cULus & CSA recognized only when ordered with marking on switch (see General Specs) Toggles Series S High Capacity Standard Size Toggles A115 Programmable Illuminated PB Pushbuttons Rockers Toggles Series S A High Capacity Standard Size Toggles THREE POLE WITH SCREW LUG & FLATTED LEVER * UL, cULus & CSA recognized only when ordered with marking on switch (see General Specs) Down *Approvals Model R R C US Electrical Capacity Toggle Position/Connected Terminals Pole & Throw Center Resistive Up DC 30V Keyway Inductive L/R = 3ms DC 48V DC 125V DC 250V DC 24V DC 48V DC 125V DC 250V S831D 3PST ON 2-3 5-6 8-9 NONE OFF 30A 30A 15A 7.5A 15A 10A 6A 3A S832D 3PDT ON 2-3 5-6 8-9 NONE ON 2-1 5-4 8-7 30A 30A 15A 7.5A 15A 10A 6A 3A S833D 3PDT ON 2-3 5-6 8-9 OFF ON 2-1 5-4 8-7 30A 30A 15A 7.5A 15A 10A 6A 3A Throw & Schematics: 2 5 (COM) — 8 2 3PST 5 (COM) 8 Note: Terminal numbers are on the switch 3PDT 3 6 9 3 1 6 4 9 7 Notes: Standard Hardware: AT503M Face Hex Nut, AT506M Locking Ring, AT508 Lockwasher, AT527M Backup Hex Nut. See Accessories & Hardware section. Three Pole M4.5x6 Keyway Keylocks M12 P1 6 3 9 28° 8 7 (12.0) Typ .472 Rotaries (4.0) .157 (42.0) 1.654 5 2 1 4 (8.15) .321 (14.5) Typ .571 (27.0) 1.063 (12.0) .472 Slides (9.0) .354 (43.0) 1.693 (34.0) 1.339 Tilt Tactiles S831D does not have terminals 1, 4 & 7. Positive (+) must be connected to end terminals & negative to common terminals (12.5) Dia .492 Touch (9.0) .354 Indicators (3.0) Dia .118 Accessories Maximum Panel Thickness: .177” (4.5mm) Supplement S832D A116 www.nkk.com A DOUBLE POLE WITH SCREW LUG S732 –– –– DPDT ON 2-3 5-6 2 Throw & Schematics: (COM) NONE ON 2-1 5-4 Inductive AC 125V AC 250V DC 30V AC 125V PF 0.6 50A 30A 50A 25A 5 Note: Terminal numbers are on the switch DPDT 3 1 6 4 Notes: Standard Hardware: AT503M Face Hex Nut, AT506M Locking Ring, AT508 Lockwasher, AT527M Backup Hex Nut. See Accessories & Hardware section. Keyway M4 x 10 M6 x 8 M12 P1 6 3 5 2 4 1 (17.0) Typ .669 (50.0) 1.969 (60.0) 2.362 Rotaries 32° (10.0) Dia .394 (10.0) .394 (39.0) 1.535 (18.0) .709 Slides (29.5) 1.161 (38.0) 1.496 Tactiles Cap of phenolic resin is black Panel Mount with Mounting Screws (14.5) Dia .571 Tilt (4.5) Dia Typ .177 (25.0) Typ .984 Touch Maximum Panel Thickness: .158” (4.0mm) (12.5) Dia .492 (12.5) Dia .492 (12.5) Dia .492 Maximum Panel Thickness: .118” (3.0mm) Accessories Maximum Panel Thickness: .079” (2.0mm) (11.5) .453 (1.5) .060 Maximum Panel Thickness: .118” (3.0mm) www.nkk.com S732 Supplement (3.0) Dia .118 Indicators Panel Mount with Bushing Hardware (9.0) .354 Pushbuttons Pole & Throw R Resistive Up Programmable Illuminated PB Model Center Keylocks Down Keyway Rockers Electrical Capacity Toggle Position/Connected Terminals Approvals Toggles Series S High Capacity Standard Size Toggles A117