Download Specifications

Series KB
Toggles
General Specifications
Rockers
Miniature Pushbuttons
Electrical Capacity (Resistive Load)
Other Ratings
Materials & Finishes
Housing:
Movable Contactor:
Stationary Contacts:
Housing Base:
Terminal Base:
Common Terminals:
End Terminals:
Lamp Terminals:
Operating Temperature Range: Humidity: Vibration: Shock: Installation
Standards & Certifications
Supplement
Accessories
Tilt
Environmental Data
Touch
D
Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: Indicators
Tactiles
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Power Level (silver): 1A @ 125/250V AC or 1A @ 30V DC
Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
50 milliohms maximum
1,000 megohms minimum @ 500V DC
For Silver: 1,000V AC minimum between contacts for 1 minute minimum &
1,500V AC minimum between contacts & case for 1 minute minimum;
For Gold: 750V AC minimum between contacts for 1 minute minimum &
1,500V AC minimum between contacts & case for 1 minute minimum
100,000 operations minimum
50,000 operations minimum for silver; 100,000 operations minimum for gold
Single pole 0.98 ~ 2.45N for maintained & 0.98 ~ 1.96N for momentary;
Double pole 1.47 ~ 3.43N for maintained & 1.47 ~ 2.94N for momentary
Nonshorting (break-before-make)
Pretravel .087” (2.2mm); Overtravel .031” (0.8mm); Total Travel .118” (3.0mm)
Polyamide (UL94V-0)
Silver for power circuit; copper with gold plating for logic level circuit
Silver for power circuit; copper with gold plating for logic level circuit
Polyamide (UL94V-0)
Polyester
Phosphor bronze with silver flash plating for power circuit;
Phosphor bronze with gold flash plating for logic level circuit
Brass with silver flash plating for power circuit;
Brass with gold flash plating for logic level circuit
Phosphor bronze with nickel flash plating
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 3 shocks in each direction)
Mounting Torque: 0.78Nm (6.9 lb • in) maximum
Cap Installation Force: 4.51N (1.0 lbf) maximum downward force on cap
Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section.
Flammability Standards: UL94V-0 housing & housing base
UL: File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” before first dash in part number to order UL recognized switch.
Single & double pole models recognized at 1A @ 125/250V AC, 1A @ 30V DC, & 0.4VA @ 28V DC.
CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” before first dash in part number to order CSA certified switch.
Single & double pole models recognized at 1A @ 125/250V AC, 1A @ 30V DC, & 0.4VA @ 28V DC.
D22
www.nkk.com
Toggles
Series KB
Miniature Pushbuttons
Rockers
Distinctive Characteristics
Front panel relamping.
Choice of bright or super bright LEDs in red, amber, green,
white, and blue.
D
Latchdown feature gives indication of circuit status. Audible
and tactile feedback with smooth and responsive operation.
Keylocks
Snap-action mechanism for long life.
Programmable Illuminated PB
Pushbuttons
Bright illumination with numerous color variations. Spot illumination available.
Square, rectangular, and round shaped caps.
Rotaries
Stainless steel frame on snap-in models has a specially
designed projection, which prevents rotation and correctly
orients switch in panel.
Slides
12mm body diameter.
Tactiles
Molded-in terminals lock out flux, dust, and other contaminants.
8mm panel thickness capability. Rear panel bushing or
snap-in mounting.
Tilt
Optional PCB adaptors in straight and right angle types.
Matching indicators available.
Supplement
Accessories
Indicators
Touch
Actual Size
www.nkk.com
D23
Toggles
Series KB
TYPICAL SWITCH
Programmable Illuminated PB
Pushbuttons
Rockers
KB
1
5
Poles
D
SPDT
2
DPDT
( ) = Momentary
6
ON
S
Square
C
Round
R
Rectangular
K
ON
Barrier Type
No
No Barrier
Code
Black only
B
Contacts & Terminals
Snap-in Mounting
(ON)
W01
Housing
Bushing Mounting
Circuits
ON
K
Shapes
1
5
C
K
Square
M
Round
N
Rectangular
Alternate Action
with Latchdown
W01
Silver Contacts and
Solder Lug Terminals
1A @ 125/250V AC
G01
Gold Contacts and
Solder Lug Terminals
0.4VA @ 28V AC/DC
Rotaries
Keylocks
Miniature Pushbuttons
IMPORTANT:
Tactiles
Slides
Switches are supplied without UL, cULus & CSA marking unless specified.
UL, cULus & CSA recognized only when ordered with marking on the switch.
Specific models, ratings, & ordering instructions are noted on the General
Specifications page.
Tilt
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Touch
KB15CKW01-12-FF
12-volt Incandescent Lamp
Indicators
Round
with Bushing Mounting
Accessories
SPDT
ON-(ON) Circuit
Solid Cap with
Green Lens and Green Filter
Black Housing
Supplement
Silver Contacts and
Solder Lug Terminals;
Rated 1A @ 125/250V AC
D24
www.nkk.com
With Barrier
Series KB
Toggles
Miniature Pushbuttons
ORDERING EXAMPLE
Incandescent Lamp Used with Solid Cap
Solid Cap: Lens/Filter Colors
5-volt
12
12-volt
No Code
Nonilluminated
A
Black/None (Nonilluminated Only.
Available in Square and Round Only.)
BB
White/White
FB
Green/White
CB
Red/White
FF
Green/Green
CC
Red/Red
GB
Blue/White
EB
Yellow/White
GG
Blue/Blue
Incandescent or Neon Used with Insert Cap
D
Insert Cap: Lens/Filter Colors
05
5-volt
JB
Clear/White
12
12-volt
JC
Clear/Red
01
110-volt Neon
JE
Clear/Yellow
No Code
Nonilluminated
* JF
Clear/Green
*JG
Clear/Blue
Rotaries
05
Programmable Illuminated PB
Cap Types & Colors
Keylocks
Lamps
Pushbuttons
Rockers
FF
Slides
12
Tactiles
* JF & JG not suitable with neon.
Bright LED Used with Cap for LED
Amber
5F
Green
No Resistor
05
5-volt
12
12-volt
24
24-volt
JB
Clear/White
JC
Clear/Red
JD
Clear/Amber
JF
Clear/Green
Super Bright LED Used with Cap for LED
White
6F
Green
6G
Blue
LED Cap: Lens/Diffuser Colors
JB
Clear/White
Supplement
6B
Tilt
5D
No Code
Square Spot Illuminated
Black Cap/White Window
Touch
Red
AB
Indicators
5C
Resistor
Accessories
Colors
LED Cap: Lens/Diffuser Colors
www.nkk.com
D25
Toggles
Series KB
POLES & CIRCUITS
Pushbuttons
Rockers
Plunger Position
( ) = Momentary
Connected Terminals
Throw & Switch/Lamp Schematics
Notes: Switch is marked with “+” and “–”.
Lamp circuit is isolated and requires
external power source.
Normal
Down
Normal
Down
KB15
*KB16
ON
ON
(ON)
ON
2-3
2-1
SPDT
KB25
*KB26
ON
ON
(ON)
ON
2-3 5-6
2-1 5-4
DPDT
Pole
Model
SP
DP
D
2 (COM)
3
L (+)
(-) L
L (+)
(-) L
1
2
(COM)
3
1
5
6
4
* When in latchdown position for the alternate circuit, cap position is .055” (1.4mm) above the built-in bezel.
MOUNTING TYPES & SHAPES
Bushing Mounting
S
.551” (14.0mm)
Square
C
.551” (14.0mm)
Round
R
.551” x .728” (14.0mm x 18.5mm)
Rectangular
Rotaries
Keylocks
Programmable Illuminated PB
Miniature Pushbuttons
No barrier
With barrier
No barrier
With barrier
Slides
Bezel or barrier is an integral part of the switch body. One mounting nut AT057 supplied with each switch.
Snap-in Mounting
.551” (14.0mm)
Square
M
.551” (14.0mm)
Round
N
.551” x .728” (14.0mm x 18.5mm)
Rectangular
Tilt
Tactiles
K
No barrier
With barrier
No barrier
With barrier
Touch
Bezel or barrier is an integral part of the switch body.
Panel Cutouts
Bushing Mounting
Snap-in Mounting
Indicators
(1.2) R
.047
Accessories
Without
Keyway
(12.3) Dia
.484
Panel Thickness:
.020” ~ .315”
(0.5 ~ 8.0mm)
(4.9)
.193
(12.3) Dia
.484
With
Keyway
Panel Thickness:
.039” ~ .138”
(1.0 ~ 3.5mm)
(6.8)
.268
Panel thicknesses, when using optional accessories, are shown with the accessories at the end of this KB section.
Supplement
HOUSING
K
D26
Housing available in black only. Bezel or barrier is an integral part of the switch body.
www.nkk.com
(12.3) Dia
.484
Toggles
Series KB
CONTACT MATERIALS, RATINGS & TERMINALS
Power Level
1A @ 125V AC & 250V AC
G
Gold Contacts
Logic Level
0.4VA maximum @ 28V AC/DC
01
Solder Lug
Complete explanation of operating range in Supplement section.
AT055 Crossover Guard
(5.0)
.197
(2.0)
(1.8)
.079
.071
(1.0)
.039
Thk = (0.2) Com = (0.1)
.008
.005
(12.4) Dia
.488
A partitioned plastic guard is supplied with each switch to provide insulation between terminals.
Rockers
Silver Contacts
Pushbuttons
W
(14.0) Dia
.551
Installation steps:
(17.0)
.669
1. Identify wire-to-terminal connections.
2. Thread wires through the guard.
D
3. Solder the connections.
4. Push the guard fully onto the switch body.
BARRIER TYPE
B
No Barrier
With Barrier
Built-in barrier only available for Square and Rectangular
Built-in bezel
Keylocks
No Code
LAMP COLORS & SPECIFICATIONS
Rotaries
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source. Polarity marks are on the bottom of the switch.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Ambient Temperature Range for lamps below: –25°C ~ +50°C.
Neon
No Code
12
01
Voltage
V
5V AC
12V AC
110V AC
Current
I
115mA
60mA
1.5mA
Endurance
Hours
7,000 average
Recommended Resistors
for Neon:
33K ohms for 110V AC;
100K ohms for 220V AC
10,000
Tilt
T-1 Bi-pin
05
Tactiles
AT615
Incandescent
Slides
Incandescent & Neon Lamps
AT611
Programmable Illuminated PB
Miniature Pushbuttons
No Lamp
Bright LED with Resistor
T-11⁄4 Bi-pin
AT634
5-volt
(+)
2-element
with 1 Resistor
(-)
5C
5D
5F
Resistor Codes
Touch
Green
05
12
24
Maximum Forward Current
IFM
—
—
—
Typical Forward Current
IF
25mA
20mA
10mA
Forward Voltage
VF
5V
12V
24V
Maximum Reverse Voltage
VRM
4V
8V
16V
Current Reduction Rate Above 25°C
∆IF
—
—
—
AT634
12-volt
(+)
4-element
with 2 Resistors
(-)
www.nkk.com
AT634
(+)
24-volt
4-element
with 2 Resistors
Indicators
Color Codes:
Amber
Accessories
LEDs are colored
in OFF state.
Red
(-)
D27
Supplement
AT634
Toggles
Series KB
LAMP COLORS & SPECIFICATIONS
Bright LED without Resistor
Red
Amber
Green
5C
5D
5F
Red
Amber
Green
Maximum Forward Current
IFM
30mA
30mA
30mA
Typical Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
1.9V
2.0V
2.1V
Maximum Reverse Voltage
VRM
5V
5V
5V
Current Reduction Rate Above 25°C
∆IF
Rockers
AT635
Color Codes
LEDs are colored
in OFF state.
Pushbuttons
Programmable Illuminated PB
Miniature Pushbuttons
(+)
D
(-)
No Code
0.42mA/°C
Ambient Temperature Range
T-1 ⁄ Bi-pin
12
No Resistor
–25° ~ +50°C
Super Bright Single Element LED
ATTENTION
AT625G Blue
ELECTROSTATIC
SENSITIVE DEVICES
AT631B White
Keylocks
AT632F Green
Rotaries
(+)
(-)
6B
6F
Color
White
Green
Blue
Maximum Forward Current
IFM
30mA
30mA
30mA
Typical Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
3.3V
3.3V
3.3V
Maximum Reverse Voltage
VRM
7V
7V
7V
Current Reduction Rate Above 25°C
∆IF
0.40mA/°C
0.40mA/°C
0.40mA/°C
Ambient Temperature Range
T-1 Bi-pin
6G
–25° ~ +50°C
CAP TYPES & COLOR COMBINATIONS
Slides
Color Codes:
A Black
B White
C Red
E Yellow
F Green
G Blue
J Clear
Solid Cap for Incandescent Lamp & Nonilluminated
Tactiles
Lens/Filter Colors Available:
Supplement
Nonilluminated Only;
Square & Round Only
BB
FB
CB
FF
CC
GB
EB
GG
AT486
Round
AT485
Square
(11.6) Sq
.457
(4.5)
.177
(6.2)
.244
(11.6) Dia
.457
(4.5)
.177
(6.2)
.244
Material: Polycarbonate
AT4021
Rectangular
(11.6)
.457
Translucent Colored Lens
(16.1)
.634
(4.5)
.177
(6.3)
.248
Translucent Colored Filter
Lamp AT611
Finish: Glossy
Insert Cap for Incandescent or Neon Lamp & Nonilluminated
Lens/Filter Colors Available:
Accessories
Indicators
Touch
Tilt
A
JB
JF
JC
JG
(11.6) Sq
.457
JE
JF and JG not suitable
with neon lamp.
D28
AT488
Round
AT487
Square
(11.6) Dia
.457
(4.5)
.177
(4.5)
.177
(11.6)
.457
(6.2)
.244
(6.2)
.244
Material: Polycarbonate
www.nkk.com
Transparent Clear Lens
AT4022
Rectangular
(16.1)
.634
(4.5)
.177
(6.3)
.248
Finish: Glossy
Translucent Colored Filter
Lamp AT611 Lamp AT615
Series KB
Toggles
Miniature Pushbuttons
CAP TYPES & COLOR COMBINATIONS
A Black
B White
C Red
D Amber
E Yellow
F Green
G Blue
J Clear
Rockers
Color Codes:
Spot Illuminated Cap for Bright LED without Resistor or with Resistor
AT4051
Square
Material: Polycarbonate
(6.2)
.244
Bright LED
AT635
Finish: Matte
Bright LED
AT634
Cap for Bright LED without Resistor or LED with Resistor
JC
AT4133
AT4132
AT4134
Square
Round
Rectangular
AT4158
AT4160
AT4159
JD
(4.5)
.177
(11.6) Dia
.457
(4.5)
.177
(6.2)
.244
(6.2)
.244
(11.6) Sq
.457
JF
Translucent Diffuser
(16.1)
.634
(4.5)
.177
(6.3)
.248
Bright LED
AT635
Finish: Glossy
Bright LED
AT634
Tilt
Material: Polycarbonate
(11.6)
.457
Transparent Clear Lens
Tactiles
JB
Keylocks
Lens/Diffuser Colors Available: (AT4133, 4132, 4134 white diffusers; AT4158, 4160, 4159 colored diffusers)
D
Programmable Illuminated PB
(11.6) Sq
.457
(4.6)
.181
Rotaries
(3.0)
.118
(1.8)
.071
(5.0)
.197
Slides
AB
Opaque Black Cap with
Translucent White Window
for Spot Illumination
Pushbuttons
Cap/Window Colors Available:
Touch
Cap for Super Bright LED
Lens/Diffuser Colors Available:
(4.5)
.177
(11.6) Dia
.457
(4.5)
.177
(6.2)
.244
(6.2)
.244
(11.6) Sq
.457
Translucent Clear Lens
AT4134
Rectangular
(11.6)
.457
Indicators
AT4132
Round
Translucent White Diffuser
(16.1)
.634
Accessories
AT4133
Square
(4.5)
.177
(6.3)
.248
Material: Polycarbonate
Finish: Glossy
www.nkk.com
Super Bright LEDs
AT625
AT631 AT632
Supplement
JB
D29
Series KB
Toggles
Miniature Pushbuttons
TYPICAL SWITCH DIMENSIONS
Single & Double Pole
Rockers
Square • Bushing Mount
(5.0)
.197
(1.0) x (2.0) Typ
.039 x .079
(0.2) Typ
.008
(1.8)
.071
(4.9)
.193
COM
(1.8) Typ
.071
(11.6) Sq
.457
(14.0) Sq
.551
D
(1.4)
.055
(3.5)
.138
KB15SKW01-05-GG
(5.3)
(24.7)
.209
.972
Latchdown Position
Keyway
6
3
5
2
4
1
(.127)
.005
L
L
(5.08)
.200
(1.7) Typ
.067
(1.0)
.039
(14.2)
.559
(9.0)
.354
(5.0)
.197
Single pole models do not have terminals 4, 5, & 6. Round • Bushing Mount
Single & Double Pole
(5.0)
.197
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
M12 P1
(1.8)
.071
(1.0) x (2.0) Typ
.039 x .079
M12 P1
(0.2) Typ
.008
(4.9)
.193
COM
Slides
(1.8) Typ
.071
(1.4)
.055
(3.5)
.138
(14.2)
.559
(5.3)
(24.7)
.209
.972
Latchdown Position
6
3
5
2
4
1
(.127)
.005
L
L
(5.08)
.200
(1.7) Typ
.067
(1.0)
.039
(9.0)
.354
(5.0)
.197
Tactiles
(11.6) Dia
.457
(14.0) Dia
.551
Keyway
Single pole models do not have terminals 4, 5, & 6. Rectangular • Bushing Mount
Single & Double Pole
Touch
Tilt
KB25CKW01-05-GG
(5.0)
.197
(1.0) x (2.0) Typ
.039 x .079
M12 P1
(0.2) Typ
.008
Indicators
(11.6)
.457
(14.0)
.551
(1.8) Typ
.071
Accessories
Supplement
(18.5)
.728
D30
(4.9)
.193
COM
(16.1)
.634
KB15RKW01-05-GG
(1.8)
.071
(1.4)
.055
(3.5)
.138
(14.2)
.559
(24.7)
(5.3)
.972
.209
Latchdown Position
6
3
5
2
4
1
(.127)
.005
L
L
(5.08)
.200
(1.7) Typ
.067
(1.0)
.039
(5.0)
.197
Single pole models do not have terminals 4, 5, & 6. www.nkk.com
Keyway
(9.0)
.354
Series KB
Toggles
Miniature Pushbuttons
TYPICAL SWITCH DIMENSIONS
Single & Double Pole
Square • Snap-in Mount
Rockers
(1.8)
.071
COM
1
L
(5.08)
.200
(1.7) Typ
.067
(1.0)
.039
D
(9.0)
.354
(5.0)
.197
KB16KKW01-05-CB
Single pole models do not have terminals 4, 5, & 6. Single & Double Pole
Round • Snap-in Mount
(1.8)
.071
(0.2) Typ
.008
(4.9)
.193
COM
5
2
4
1
(.127)
.005
L
(5.08)
.200
(1.7) Typ
.067
(1.0)
.039
(24.7)
(5.3)
.972
.209
Latchdown Position
(9.0)
.354
(5.0)
.197
Tactiles
(1.4)
.055
(3.5)
.138
3
KB26MKW01-05-CB
Single pole models do not have terminals 4, 5, & 6. Single & Double Pole
Rectangular • Snap-in Mount
(1.0) x (2.0) Typ
.039 x .079
(0.2) Typ
.008
(11.6)
.457
(14.0)
.551
(1.8)
.071
(4.9)
.193
COM
(1.8) Typ
.071
(16.1)
.634
(18.5)
.728
(1.4)
.055
(3.5)
.138
Keyway
6
3
5
2
4
1
(.127)
.005
L
L
(1.0)
.039
(24.7)
(5.3)
.972
.209
Latchdown Position
Touch
(5.08)
.200
(1.7) Typ
.067
(5.0)
.197
(9.0)
.354
Single pole models do not have terminals 4, 5, & 6. www.nkk.com
Tilt
(11.6) Dia
.457
(14.0) Dia
.551
6
L
(1.8) Typ
.071
(2.3)
.090
Keyway
Slides
(1.0) x (2.0) Typ
.039 x .079
Indicators
Rotaries
(24.7)
(5.3)
.972
.209
Latchdown Position
2
Accessories
(1.4)
.055
(3.5)
.138
5
4
(.127)
.005
KB16NKW01-05-CB
D31
Supplement
(11.6) Sq
.457
(14.0) Sq
.551
3
L
(1.8) Typ
.071
(2.3)
.090
6
Pushbuttons
(4.9)
.193
Keyway
Programmable Illuminated PB
(0.2) Typ
.008
Keylocks
(1.0) x (2.0) Typ
.039 x .079
Series KB
Toggles
Miniature Pushbuttons
TYPICAL SWITCH DIMENSIONS
Single & Double Pole
Rockers
Square • Barrier • Bushing Mount
(5.0)
.197
Pushbuttons
(0.2) Typ
.008
(11.6) Sq
.457
(14.0) Sq
.551
D
KB15SKW01B-6G-JB
(14.2)
.559
(5.3)
.209
(8.8)
.346
(24.7)
.972
(1.0)
.039
Square • Barrier • Snap-in Mount
(11.6) Sq
.457
(14.0) Sq
.551
(5.3)
.209
(8.8)
.346
(24.7)
.972
L
(5.08)
.200
(1.8)
.071
(4.9)
.193
(1.0)
.039
Keyway
6
3
5
2
4
1
(.127)
.005
L
L
(5.08)
.200
(1.7) Typ
.067
(9.0)
.354
(5.0)
.197
Single & Double Pole
(5.0)
.197
Tactiles
1
Single pole models do not have terminals 4, 5, & 6. Rectangular • Barrier • Bushing Mount
(0.2) Typ
.008
(4.9)
.193
COM
(18.5)
.728
KB15RKW01B-5F-JF
(5.3)
.209
(8.8)
.346
(14.2)
.559
(24.7)
.972
(1.0)
.039
Keyway
6
3
5
2
4
1
(.127)
.005
L
L
(1.8) Typ
.071
(16.1)
.634
Tilt
(1.8)
.071
(1.0) x (2.0) Typ
.039 x .079
M12 P1
(11.6)
.457
(14.0)
.551
(5.08)
.200
(1.7) Typ
.067
(9.0)
.354
(5.0)
.197
Single pole models do not have terminals 4, 5, & 6. Rectangular • Barrier • Snap-in Mount
Indicators
2
Single & Double Pole
(1.8) Typ
.071
Single & Double Pole
(1.8)
.071
(1.0) x (2.0) Typ
.039 x .079
(0.2) Typ
.008
(11.6)
.457
(14.0)
.551
Accessories
5
4
(.127)
.005
(1.7) Typ
.067
COM
(4.9)
.193
COM
(1.8) Typ
.071
(16.1)
.634
Supplement
3
(9.0)
.354
(0.2) Typ
.008
D32
6
L
(5.0)
.197
(1.0) x (2.0) Typ
.039 x .079
KB15NKW01B-5D-JD
Keyway
Single pole models do not have terminals 4, 5, & 6. Rotaries
Slides
(4.9)
.193
COM
KB15KKW01B-5C-JC
Touch
(1.8)
.071
(1.8) Typ
.071
Keylocks
Programmable Illuminated PB
(1.0) x (2.0) Typ
.039 x .079
M12 P1
(18.5)
.728
(5.3)
.209
(8.8)
.346
(24.7)
.972
(1.0)
.039
6
3
5
2
4
1
(.127)
.005
L
L
(5.08)
.200
(1.7) Typ
.067
(5.0)
.197
Single pole models do not have terminals 4, 5, & 6. www.nkk.com
Keyway
(9.0)
.354
Series KB
Toggles
Miniature Pushbuttons
OPTIONAL ACCESSORIES
5
3
NC
COM 2
4
NO
6
(12.0) Dia
.472
+
3
Pushbuttons
5
3
NC
COM 2
4
NO
6
+
(9.8)
.386
D
1
(10.16)
.400
(3.1)
.122
(0.2) Typ
.008
(2.54) Typ
.100
(2.54) Typ
(2.54) Typ
.100
.100
6
(2.54) Typ
(2.54) Typ
.100
.100
NC
3 NC
2 COM
2 COM
5
1 NO
1 NO
4
(10.16)
.400
(0.2) Typ
.008
(2.54) Typ
.100
Keyway
(0.6) Typ
.024
(0.2) Typ
.008
(2.54) Typ
.100
(10.16)
.400
(3.1)
.122
(0.3)
.012
(12.0) Dia
.472
1
(0.6) Typ
.024
(9.8)
.386
Switch (2.8)
Depth .110
(0.2) Typ
.008
(2.54) Typ
.100
Keyway
Keylocks
(0.3)
.012
(0.8) Dia Typ
.031
(10.16)
.400
Material: Glass fiber reinforced polyamide
(0.8) Dia Typ
.031
Rotaries
Switch (2.8)
Depth .110
AT702
Double Pole
Straight PC
Terminals
Note: Order adaptors separately
Slides
Dust Covers
Tactiles
Panel Thickness Range: .020 ~ .268” (0.5 ~ 6.8mm) for Bushing Mounting; .020 ~ .079” (0.5 ~ 2.0mm) for Snap-in Mounting
Dust Covers reduce the depth of switch behind panel by .047” (1.2mm).
AT4025
For Rectangular
(not for Barrier type)
Touch
Tilt
AT495
For Square & Round
(not for Barrier type)
Programmable Illuminated PB
AT701
Single Pole
Straight PC
Terminals
Rockers
PCB Adaptors
(5.1)
.201
(6.5)
.256
(11.8)
.465
(12.3) Dia
.484
(1.6)
.063
(21.0) Sq
.827
Material: Lid: PVC
(12.3) Dia
.484
(21.0)
.827
(13.0) Sq
.512
(6.5)
.256
(11.8)
.465
PVC loses pliability below 0°C (32°F).
www.nkk.com
Indicators
(13.0) Sq
.512
(1.2) R
.047
Assembled
Cap Height
Accessories
(1.2) R
.047
(7.0)
.276
(25.4)
1.004
Supplement
(7.0)
.276
Assembled
Cap Height
Base: Polyamide
D33
Series KB
Toggles
Miniature Pushbuttons
OPTIONAL ACCESSORIES
Protective Guards
AT4024
For Rectangular
(not for Barrier type)
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
AT494
For Square & Round
(not for Barrier type)
(7.0)
.276
Assembled
Cap Height
(1.2) R
.047
D
(9.0)
.354
(5.1)
.201
(6.5)
.256
(11.5)
.453
(9.0)
.354
(12.3) Dia
.484
(1.6)
.063
(19.0) Sq
.748
Material:Cover: Polycarbonate
(1.2) R
.047
(7.0)
.276
Assembled
Cap Height
(6.5)
.256
(11.5)
.453
(12.3) Dia
.484
(19.0)
.748
Panel Thickness
Range:
.020” ~ .268”
(0.5 ~ 6.8mm)
for Bushing Mounting
.020” ~ .091”
(0.5 ~ 2.3mm)
for Snap-in Mounting
Protective Guards reduce
the depth of switch
behind panel by
.047” (1.2mm).
(23.5)
.925
Base: Polyamide
Tactiles
Slides
Rotaries
ASSEMBLY INSTRUCTIONS
Cap Removal & Installation
For alternate action models
cap must be in UP position
for cap removal. Indentations
on opposite sides of the cap
provide an easy way to lift
the cap out of the holder,
using either the finger nails,
or cap extractor AT109.
LED Polarity & Orientation in Lamp Socket
Super Bright LEDs AT625,
AT631, & AT632 are
electrostatic sensitive.
LED
AT635
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
LEDs
AT625
AT631
AT632
LED
AT634
Flat
Flat
(-)
(+)
Note that the cap has a pair of
round tabs and a pair of long tabs
which should be used for correctly
replacing the cap in its holder.
Using the long tabs as guides, slide
the cap with the long tabs moving
into the slots on opposite sides of
the cap holder. Then, the round
tabs will snap into notches on the
other two sides of the holder.
Flat
(+)
Cap
(-)
Tilt
(-)
(+)
Cap Replacement
Indentation
Long Tab
(+) Marking
Positive Lamp Socket
Slot
Negative Lamp Socket
Supplement
Accessories
Indicators
Touch
Top
View of
Switch
Notch
Round Tab
AT108 Socket Wrench
for Bushing Mounting
AT109 Cap Extractor
Overtightening the
mounting nut
may damage the
switch housing.
D34
www.nkk.com
AT111 Lamping Tool
Series KB
Toggles
Miniature Pushbuttons
LEGENDS
Rockers
NKK Switches can provide custom legends for caps. Contact factory for more information.
Suggested Printable Area for KB Lens
T
AR
ST
(10.08) (11.6)
.397 .457
(10.08) Sq
.397
(0.76) Typ
.030
(11.6) Sq
.457
(10.08) Dia
.397
(0.76) Typ
.030
(0.76)Typ
.030
(11.6) Dia
.457
(14.58)
.574
(16.1)
.634
D
(0.76) Typ
.030
Keylocks
Shaded areas are printable areas.
Programmable Illuminated PB
Pushbuttons
Recommended Methods: Screen Print or Pad Print on Lens.
Epoxy based ink is recommended.
Suggested Printable Area for Film Insert
Lens
Film Insert: Clear Polyester, 4 mil max. thickness
Film
Insert
(0.76) Typ
.030
(0.76) Typ
.030
(12.98)
.511
(14.5)
.571
(0.76) Typ
.030
Tactiles
(8.48) Dia
.334
(10.0) Dia
.394
Touch
Tilt
Shaded areas are printable areas.
Indicators
(0.76) Typ
.030
Accessories
Cap
Base
(8.48) Sq
.334
(10.0) Sq
.394
Slides
(8.48) (10.0)
.334 .394
Filter or
Diffuser
Supplement
ON
Rotaries
Recommended Print Method: Laser Print
www.nkk.com
D35