A Electrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): Programmable Illuminated PB Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Angle of Throw: Materials & Finishes Bushing: Housing: Mounting Bracket: Movable Contacts: Stationary Contacts: Lamp Contacts: Base: Switch Terminals: Lamp Terminals: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Tilt Tactiles Slides Rotaries Keylocks Other Ratings Installation Touch Mounting Torque: Soldering Time & Temp: Cleaning: Standards & Certifications Flammability Standards: UL: Accessories Indicators LED Tipped Toggles General Specifications Pushbuttons Rockers Toggles Series M2100 Supplement CSA: A80 6A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum On-to-On Position Off-to-On Position Single Pole 3.19N 3.92N Double Pole 4.41N 7.06N 20° Brass with nickel plating Stainless steel Steel with tin plating Silver alloy or silver alloy with gold plating Silver with silver plating or copper or brass with gold plating Phosphor bronze Diallyl phthalate (UL94V-0) Copper with silver or gold plating Brass with silver or gold plating –10°C through +55°C (+14°F through +131°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 1.47Nm (13 lb•in) for double nut; .67Nm (6 lb•in) for single nut Wave Soldering (PC version): See Profile B in Supplement section. Manual Soldering: See Profile B in Supplement section. Note: Lever must be in center position while soldering. PC mountable device is not process sealed. Hand clean locally using alcohol based solution. UL94V-0 base File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” to end of part number to order UL recognized switch. Single pole with synchronous circuits & single color LEDs & solder lug or PC recognized at 6A @ 125V AC. File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” to end of part number to order CSA certified switch. All single pole with synchronous circuits & single color LEDs certified at 6A @ 125V AC. www.nkk.com A Rockers Distinctive Characteristics Toggles Series M2100 LED Tipped Toggles Pushbuttons Industry’s first LED illumination at tip of toggle switches. Programmable Illuminated PB Single color LEDs of red, yellow, and green, plus bicolor red/green, to meet varied design requirements. LEDs can operate independently from or synchronously with switching operation. Antijamming feature to protect contacts from damage due to excessive downward force on the toggle. Keylocks High torque bushing prevents the bushing from rotating or separating from the metal frame during installation. Rotaries Stainless steel frame resists corrosion. Slides Silver contacts are of specially composed alloy for hardness. High insulating barriers protect against crossover in double pole devices. Tactiles Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants. Tilt 1,500V dielectric strength between switch contacts and case is accomplished by clinching the frame away from the terminals. Supplement Accessories Indicators Touch Actual Size www.nkk.com A81 A LED Tipped Toggles TYPICAL SWITCH ORDERING EXAMPLE M21 Pushbuttons Rockers Toggles Series M2100 1 2 Programmable Illuminated PB Poles 1 SPDT *2 DPDT T L Isolated T Synchronous Circuits W Contact Materials & Ratings LED Circuits & Actuator Types * Available only with Terminals 01, 02, 03 Keylocks C W Silver; Rated 6A @ 125V AC G Gold; Rated 0.4VA max @ 28V AC/DC max LED Colors 2 ON NONE ON 3 ON OFF ON Single Color Rotaries 6mm Thread (Metric) 01 Solder Lug with Threaded Bushing 02 Quick Connect with Threaded Bushing E Yellow 03 Straight PC with Threaded Bushing F Green 30 Right Angle PC with Smooth Bushing (available with gold contacts only) Slides Red/Green Switches are supplied without UL & CSA marking unless specified. UL & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. Tilt Tactiles /M 1/4–40 Thread (Inch) Terminals & Mounting Types IMPORTANT: DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Touch M2112TCW01 Red LED Synchronous LED Circuit in Actuator Indicators No Code Red CF SPDT ON-NONE-ON Switch Circuit Accessories Threaded Bushings C Bicolor 1/4–40 Threaded Bushing Silver Contacts with 6-Amp Rating Solder Lug Terminals Supplement A82 01 www.nkk.com A POLES & CIRCUITS & LED ILLUMINATION Toggle Position & Terminal Numbers ON 4-6 Synchronous Single Color LED Connected LED Terminals ON 4-6 NONE NONE OFF OPEN Synchronous Bicolor LED Connected LED Terminals Red 5-6 NONE NONE Green 5-4 ON 2-3 OFF OPEN ON 2-1 SPDT LED Circuit Isolated LEDs (see schematics) Connected LED Terminals ON 4-6 ON 4-6 ON 4-6 Synchronous Single Color LED Connected LED Terminals ON 4-6 OFF OPEN ON 4-6 Synchronous Bicolor LED Connected LED Terminals Red 5-6 OFF OPEN Green 5-4 ON 2-3 5-6 NONE NONE ON 2-1 5-4 Isolated LEDs (see schematics) Connected LED Terminals ON 7-9 NONE NONE ON 7-9 Synchronous Single Color LED Connected LED Terminals ON 7-9 NONE NONE OFF OPEN Synchronous Bicolor LED Connected LED Terminals Red 8-9 NONE NONE Green 8-7 ON 2-3 5-6 OFF OPEN ON 2-1 5-4 M2122 DPDT LED Circuit Connected Power Terminals M2123 DPDT LED Circuit Connected Power Terminals Isolated LEDs (see schematics) Connected LED Terminals ON 7-9 ON 7-9 ON 7-9 Synchronous Single Color LED Connected LED Terminals ON 7-9 OFF OPEN ON 7-9 Synchronous Bicolor LED Connected LED Terminals Red 8-9 OFF OPEN Green 8-7 L(+) 3 1 L(-) 4 6 2 (COM) Red Green Isolated Bicolor LED 3 1 6 COM (+) Red 4 ( ) Green 2 (COM) Synchronous Single Color LED L(+) 3 1 L(-) 4 6 2 (COM) Synchronous Bicolor LED Red Green 3 1 6 5 COM (+) 4 External Connection Isolated Single Color LED 2 (COM) 5 L(+) 3 1 6 4 2 (COM) Isolated Bicolor LED Synchronous Single Color LED 3 5 1 3 1 4 9 COM (+) Red 7 ( ) Green 5 6 2 (COM) Synchronous Bicolor LED 9 Red Green 6 2 (COM) L(-) 7 4 7 L(+) 5 9 L(-) Red Green 3 1 6 4 9 8 COM (+) 7 External Connection Supplement LED Circuit M2113 Connected Power Terminals Rockers NONE NONE Pushbuttons ON 4-6 Programmable Illuminated PB Isolated LEDs (see schematics) Connected LED Terminals 2 (COM) Isolated Single Color LED Keylocks ON 2-1 SPDT Rotaries NONE NONE M2112 Connected Power Terminals Slides ON 2-3 Keyway Notes: Terminal numbers are not actually on the switch. LEDs require an external power source. Tactiles Up Tilt Center Touch Down Indicators Pole & Throw Accessories Model Schematics Toggles Series M2100 LED Tipped Toggles www.nkk.com A83 A The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in Supplement Section. Single Color Bicolor C E F CF Color Red Yellow Green Red/Green Units Programmable Illuminated PB The LED is an integral part of the switch and not available separately. Maximum Forward Current I FM 25 30 30 25 mA Typical Forward Current IF 20 20 20 10 mA Forward Voltage VF 2.1 2.1 2.1 1.7/2.0 V Maximum Reverse Voltage VRM 4 4 4 ––– V Current Reduction Rate Above 25°C ∆I F 0.33 0.40 0.40 0.33/0.33 mA/°C Keylocks Pushbuttons LED Tipped Toggles LED COLORS & SPECIFICATIONS Rockers Toggles Series M2100 Ambient Temperature Range Bicolor LED is translucent white when unlit. –10° ~ +55°C Rotaries LED CIRCUIT, TOGGLE, & MOUNTING TYPE COMBINATIONS L Toggle with Isolated LED Circuit Slides T Toggle with Synchronous LED Circuit (5.0) Dia .197 (14.7) .579 (14.7) .579 (6.2) Dia .244 1/4-40 Thd Standard Hardware: 2 AT513H Hex Nuts, 1 AT507H Locking Ring, 1 AT509 Lockwasher Standard & optional hardware details in Accessories & Hardware section. Threaded Bushing combines with Terminal codes 01, 02, & 03. Smooth Bushing combines with Terminal code 30. (6.5) Dia .256 (2.2) Dia .087 (6.1) .240 Max. Panel Thickness without Locking Ring .134” (3.4mm) (6.5) Dia .256 (5.8) .228 (0.6) .024 Tilt Tactiles Finish: Brushed aluminum Max. Panel Thickness with Standard Hardware .102” (2.6mm) 20° 20° (5.0) Dia .197 Solder Lug (4.8) .189 1/4-40 Thd 20° (2.5) Dia .098 (5.0) Dia .197 Accessories Supplement Single Pole Keyway Indicators Touch TYPICAL SWITCH DIMENSIONS M2112TCFW01 A84 (12.7) .500 (0.8) Typ .031 (4.7) Typ .185 (14.7) .579 (8.0) .315 (0.9) .035 (20.3) .799 (6.35) .250 Single color LED switch does not have terminal 5. www.nkk.com (1.17) Typ .046 6 3 5 2 4 1 (4.8) .189 (13.0) .512 (2.0) Typ .079 A TYPICAL SWITCH DIMENSIONS Double Pole Solder Lug Rockers Toggles Series M2100 LED Tipped Toggles (17.5) .689 (14.7) .579 (0.9) .035 (8.0) .315 (20.3) .799 6 3 8 5 2 7 4 1 (2.0) Typ .079 (4.8) Typ .189 (1.17) Typ .046 (6.35) .250 (13.0) .512 M2122TCFW01 Single color LED switch does not have terminal 8. Single Pole Only (2.5) Dia .098 (6.2) Dia .244 (5.0) Dia .197 (2.9) .114 (1.4) .055 4 5 6 1 2 3 (12.7) .500 Slides Keyway Right Angle PC Rotaries (4.3) .169 (5.1) .201 (13.0) .512 (14.7) .579 (7.6) .299 (0.4) .016 (1.1) .043 (16.4) .646 Single color LED switch does not have terminal 5. (1.27) Typ .050 (3.81) .150 (0.8) Typ .031 (4.7) Typ .185 Gold contact material only Tactiles (2.5) Dia .098 (5.0) Dia .197 (4.7) Typ .185 9 Pushbuttons 20° (0.8) Typ .031 Programmable Illuminated PB (4.8) .189 1/4-40 Thd Keylocks Keyway M2112TCFG30 Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Accessories Indicators W Touch CONTACT MATERIALS & RATINGS Tilt (6.35) .250 Supplement Complete explanation of operating range in Supplement section. www.nkk.com A85 TERMINALS 01 Solder Lug with Turret LED Terminal (6.35) (4.8) .250 .189 Quick Connect (6.35) (4.8) .250 .189 (2.0) .079 (1.1) .043 (1.17) .046 03 Straight PC with Turret LED Terminal Single Pole (4.8) .189 3 (6.35) (4.8) .250 .189 Epoxy Seal (1.17) Typ .046 (4.8) .189 Thk = (0.8) Typ .031 2 1 Double Pole Single color LED & isolated bicolor LED switches do not have terminal 5. 6 5 Epoxy Seal (1.57) Typ .062 (4.8) .189 Thk = (0.8) Typ .031 (4.8) .189 Thk = (0.8) Typ .031 (4.7) Typ .185 4 3 6 9 2 5 8 1 4 7 (4.8) Typ .189 (4.7) Typ .185 Single color LED & isolated bicolor LED switches do not have terminal 8. (1.8) Dia Typ .073 (1.8) Dia Typ .073 Single Pole 30 (4.7) Typ .185 Right Angle PC 6 5 4 3 2 1 LED terminals only available in brass with silver plating (3.81) .150 (16.4) .646 Single color LED & isolated bicolor LED switches do not have terminal 5. (1.8) Dia Typ .073 (2.54) Typ .100 Tactiles Slides Rotaries 02 (2.0) .079 (4.0) .157 Epoxy Seal Keylocks Programmable Illuminated PB LED Tipped Toggles A Pushbuttons Rockers Toggles Series M2100 Touch Tilt STANDARD MOUNTING HARDWARE AT513H Hexagon Nut (2 per switch) AT507H Locking Ring (1 per switch) AT509 Lockwasher (1 per switch) Material: Brass with nickel plating Material: Steel with chromate over zinc Material: Steel with chromate over zinc (6.35) Dia .250 Indicators 1/4-40 Thd (8.0) .315 (12.0) Dia .472 (2.0) .079 (6.4) Dia (10.2) Dia .252 .402 Accessories (5.8) .229 (9.0) .354 (1.5) .059 (1.7) .067 (0.8) .031 Supplement Optional Hardware: Knurled nuts, dress nuts, and ON-OFF plates are available; see details in Accessories & Hardware section. A86 www.nkk.com (0.5) .020 Series M2100 Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles General Specifications B Electrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): Contact Resistance: 10 milliohms maximum for silver; 20 milliohms maximum for gold Insulation Resistance: 1,000 megohms minimum @ 500V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 50,000 operations minimum Electrical Life: 25,000 operations minimum Nominal Operating Force: On-to-On Position Off-to-On Position Paddles Single Pole 3.19N 3.92N Double Pole 4.41N 7.06N Rockers Single Pole 6.37N 9.80N Double Pole 13.73N 17.65N Angle of Throw: 20° Rotaries Slides Tactiles Tilt Housing: Mounting Bracket: Movable Contacts: Stationary Contacts: Lamp Contacts: Base: Switch Terminals: Lamp Terminals: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Indicators Touch Installation Accessories 6A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Materials & Finishes Supplement LED Tipped Rockers & Paddles Soldering Time & Temp: Cleaning: Stainless steel Stainless steel Silver alloy or silver alloy with gold plating Silver with silver plating or copper or brass with gold plating Phosphor bronze Diallyl phthalate (UL94V-0) Copper with silver or gold plating Brass with silver or gold plating –10°C through +55°C (+14°F through +131°F) for rockers –25°C through +70°C (–13°F through +158°F) for paddles 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering (PC version): See Profile B in Supplement section. Manual Soldering: See Profile B in Supplement section. Note: Lever must be in center position while soldering. PC mountable device is not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V-0 base UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” before dash in part number to order UL recognized switch. Single pole rockers with synchronous circuits & single color LEDs & solder lug or PC recognized at 6A @ 125V AC. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” before dash in part number to order CSA certified switch. All single pole rockers with synchronous circuits & single color LEDs certified at 6A @ 125V AC. B92 www.nkk.com TYPICAL SWITCH ORDERING EXAMPLE N Poles 1 SPDT *2 DPDT CF W LED Colors * Available only with Rockers with Terminals 01, 02, 03 Red E Yellow F Green B Contact Materials & Ratings Single Color C 01 Pushbuttons 2 W Silver; Rated 6A @ 125V AC G Gold; Rated 0.4VA max @ 28V AC/DC max Programmable Illuminated PB 1 Bicolor OFF ON LED Circuits & Actuator Types Rocker Terminals & Mounting Types 01 Solder Lug with Flat Frame R Isolated 02 Quick Connect with Flat Frame N Synchronous 03 Straight PC with Flat Frame 13 Straight PC with Bracket Mount 01 Solder Lug with Snap-in Frame Paddle Keylocks ON P Isolated 02 Quick Connect with Snap-in Frame J Synchronous 03 Straight PC with Snap-in Frame 13 Straight PC with Bracket Mount IMPORTANT: Optional Bezel & Colors For Snap-in Frame A Black B White E Yellow F Green G Blue H Gray Touch Switches are supplied without UL & CSA marking unless specified. UL & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. Rotaries 3 Tactiles ON DESCRIPTION FOR TYPICAL ORDERING EXAMPLE M2112NCFW01 Indicators NONE Red/Green LED SPDT ON-NONE-ON Switch Circuit Silver Contacts with 6-Amp Rating Synchronous LED Circuit in Rocker Actuator Accessories ON Supplement 2 Red/Green Tilt CF Circuits Slides M21 Rockers Toggles Series M2100 LED Tipped Rockers & Paddles Solder Lug Terminals www.nkk.com B93 Toggle Position & Terminal Numbers B Down Center Up ON 2-3 NONE NONE ON 2-1 Isolated LEDs (see schematics) Connected LED Terminals ON 4-6 NONE NONE ON 4-6 Synchronous Single Color LED Connected LED Terminals ON 4-6 NONE NONE OFF OPEN Synchronous Bicolor LED Connected LED Terminals Red 5-6 NONE NONE Green 5-4 ON 2-3 OFF OPEN ON 2-1 Isolated LEDs (see schematics) Connected LED Terminals ON 4-6 ON 4-6 ON 4-6 Synchronous Single Color LED Connected LED Terminals ON 4-6 OFF OPEN ON 4-6 Synchronous Bicolor LED Connected LED Terminals Red 5-6 OFF OPEN Green 5-4 ON 2-3 5-6 NONE NONE ON 2-1 5-4 Isolated LEDs (see schematics) Connected LED Terminals ON 7-9 NONE NONE ON 7-9 Synchronous Single Color LED Connected LED Terminals ON 7-9 NONE NONE OFF OPEN Synchronous Bicolor LED Connected LED Terminals Red 8-9 NONE NONE Green 8-7 ON 2-3 5-6 OFF OPEN ON 2-1 5-4 Isolated LEDs (see schematics) Connected LED Terminals ON 7-9 ON 7-9 ON 7-9 Synchronous Single Color LED Connected LED Terminals ON 7-9 OPEN OFF ON 7-9 Synchronous Bicolor LED Connected LED Terminals Red 8-9 OFF OPEN Green 8-7 Model Pole & Throw M2112 SPDT LED Circuit Connected Power Terminals M2113 SPDT Connected Power Terminals M2122 DPDT LED Circuit Slides Rotaries Connected Power Terminals M2123 DPDT Tilt LED Circuit Connected Power Terminals Tactiles LED Tipped Rockers & Paddles POLES & CIRCUITS & LED ILLUMINATION LED Circuit Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series M2100 Schematics Notes: Terminal numbers are not actually on the switch. LEDs require an external power source. Isolated Single Color LED 2 (COM) L(+) 3 1 L(-) 4 6 2 (COM) Isolated Bicolor LED Red Green 3 1 (+) Red 4 ( ) Green 6 COM 2 (COM) Synchronous Single Color LED L(+) 3 1 L(-) 4 6 2 (COM) Red Synchronous Bicolor LED Green 3 1 6 5 COM (+) 4 External Connection Isolated Single Color LED 2 (COM) 5 L(+) 3 1 Isolated Bicolor LED 6 4 2 (COM) 3 Synchronous Single Color LED Red Green 6 2 (COM) Synchronous Bicolor LED 9 5 1 3 L(-) 7 4 (+) Red 7 ( ) Green 9 COM 5 1 6 4 2 (COM) 7 L(+) 9 5 L(-) Red Green 3 1 6 4 9 8 COM (+) 7 External Connection LED COLORS & SPECIFICATIONS Maximum Forward Current I FM 25 30 30 25 25 30 Typical Forward Current IF 20 20 20 20 20 Forward Voltage VF 2.1 2.1 2.1 1.7/2.0 Maximum Reverse Voltage VRM 4 4 4 ––– Current Reduction Rate Above 25°C ∆I F 0.33 0.40 Indicators Touch Red Accessories Paddles Supplement Rockers The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires an external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in Supplement Section. The LED is an integral part of the switch and not available separately. Bicolor LED is translucent white when unlit. Ambient Temperature Range B94 Single Color C E Bicolor F CF Yellow Green Red/Green C E Bicolor F CF Red/Green Units 25 30/25 mA 20 20 20/20 mA 2.25 2.1 2.2 2.0/2.2 V 5 5 5 ––– V 0.40 0.33 0.43/0.38 mA/°C Red 0.40 0.33/0.33 0.33 –10° ~ +55°C www.nkk.com Single Color Yellow Green –25° ~ +50°C –25° ~ +70°C LED CIRCUIT, ROCKER, & MOUNTING TYPE COMBINATIONS N Rocker with Synchronous LED Circuit (16.8) .661 (13.5) .531 20° (12.0) .472 (9.8) .386 Material: Polyamide Finish: Matte B (12.0) .472 (9.8) .386 (17.8) .701 (23.8) .937 (3.5) .138 (3.5) .138 (0.6) .024 Color: Black Maximum Panel Thickness .126” (3.2mm) (16.8) .661 (13.5) .531 20° Pushbuttons Rocker with Isolated LED Circuit Bracket combines with Terminal code 13. Flat Frame combines with Terminal codes 01, 02, & 03. (10.1) .398 (2.6) Dia Typ .102 TYPICAL ROCKER SWITCH DIMENSIONS Single Pole (12.0) .472 (4.8) .189 (23.8) .937 20° (29.5) 1.161 Solder Lug (0.6) .024 (0.8) Typ .031 (4.7) Typ .185 6 3 5 2 4 1 Keylocks (2.4) Dia Typ .094 Programmable Illuminated PB R Rockers Toggles Series M2100 LED Tipped Rockers & Paddles (13.0) .512 (3.5) .138 (9.8) .386 (20.3) .799 (1.17) Typ .046 (6.35) .250 (2.0) Typ .079 (4.8) .189 (12.7) .500 M2112NCFW01 Single color LED switch does not have terminal 5. Double Pole (2.4) Dia Typ .094 (12.0) .472 (0.6) .024 (4.8) .189 (23.8) .937 20° (0.8) Typ .031 (4.7) Typ .185 9 6 3 8 5 2 7 4 1 (13.0) .512 Tilt (29.5) 1.161 Solder Lug Tactiles (6.35) .250 Slides (6.9) .272 (9.3) .366 Rotaries (2.5) Dia .098 (2.5) Dia .098 Single Pole Only (2.5) Dia .098 (9.3) .366 (9.8) .386 (3.5) .138 (20.3) .799 (6.35) .250 (0.5) Typ .020 (1.17) Typ .046 (3.2) Typ .126 6 3 5 2 4 1 (4.8) .189 (12.7) .500 (17.8) .701 (13.0) .512 (1.17) Typ .046 Direction of Actuation (0.8) Typ .031 (4.7) Typ (15.8) .622 .185 20° Straight PC • Bracket (9.0) .354 (4.5) .177 (12.0) .472 Touch M2122NCFW01 Single color LED switch does not have terminal 8. (17.5) .689 (10.1) .398 Single color LED switch does not have terminal 5. Silver contact material is standard. www.nkk.com Indicators (20.3) .799 (2.0) Typ .079 (4.8) Typ .189 (1.17) Typ .046 (6.35) .250 Accessories (9.8) .386 (3.5) .138 Supplement (6.9) .272 (9.3) .366 M2112NCFW13 B95 Programmable Illuminated PB LED Tipped Rockers & Paddles LED CIRCUIT, PADDLE, & MOUNTING TYPE COMBINATIONS P B J Pushbuttons Rockers Toggles Series M2100 Paddle with Isolated LED Circuit Maximum Panel Thickness .039” ~ .126” (1.0 ~ 3.2mm) without Bezel .039” ~ .098” (1.0 ~ 2.5mm) with Bezel Paddle with Synchronous LED Circuit (3.2) .126 Material: Polyamide (13.7) .539 Finish: Matte Color: Black Maximum Panel Thickness .126” (3.2mm) 20° (3.2) .126 (4.5) .177 (15.9) .626 (5.9) R .232 (0.5) .020 (7.1) .280 (20.1) .791 Keylocks (12.7) .500 (5.9) R .232 (12.4) .490 (3.5) .138 Bracket combines with Terminal code 13 TYPICAL PADDLE SWITCH DIMENSIONS Solder Lug • Snap-in Single Pole Only (4.8) .189 (0.5) .020 Slides Rotaries (4.5) .177 (13.1) .516 (2.8) .110 Snap-in combines with Terminal codes 01, 02, & 03 (18.0) .709 20° (2.0) .079 (5.0) .197 (11.5) .453 (12.2) .480 Tactiles Tilt 20° M2112JCFW01 (3.2) .126 (0.8) Typ .031 6 (4.7) Typ .185 (2.8) .110 (13.7) .539 (7.1) .280 (26.5) 1.043 (1.17) Typ .046 (6.35) .250 3 5 2 4 1 (13.0) .512 (2.0) Typ .079 (4.8) .189 (12.7) .500 Single color LED switch does not have terminal 5. Single Pole Only Touch Straight PC • Bracket (9.0) .354 Indicators (4.5) .177 20° (2.0) .079 (5.0) .197 (9.0) .354 (11.5) .453 Accessories Supplement (0.8) Typ .031 (4.7) Typ (15.8) .622 .185 M2112JCFW13 B96 (3.2) .126 (20.1) .791 (6.35) .250 (3.5) .138 (0.5) Typ .020 (20.2) .795 Silver contact material is standard. Single color LED switch does not have terminal 5. www.nkk.com (1.17) Typ .046 (3.2) Typ .126 6 3 5 2 4 1 (4.8) .189 (12.7) .500 (13.0) .512 (1.17) Typ .046 Series M2100 CONTACT MATERIALS & RATINGS Power Level 6A @ 125V AC & 3A @ 250V AC Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum B Pushbuttons G Silver over Silver Complete explanation of operating range in Supplement section. 02 (2.0) .079 (4.0) .157 Epoxy Seal (6.35) (4.8) .250 .189 Quick Connect (6.35) (4.8) .250 .189 (2.0) .079 (1.1) .043 (1.17) .046 (4.8) .189 Thk = (0.8) Typ .031 Single Pole (4.8) .189 3 Epoxy Seal (1.17) Typ .046 (4.8) .189 Thk = (0.8) Typ .031 13 2 5 1 4 (4.7) Typ .185 Single color LED & isolated bicolor LED switches do not have terminal 5. 3 6 2 5 1 4 9 (4.8) Typ .189 8 (4.7) Typ .185 7 Single color LED & isolated bicolor LED switches do not have terminal 8. (1.8) Dia Typ .073 (1.8) Dia Typ .073 Single Pole Straight PC with Bracket & Turret LED Terminal Tactiles (6.35) (4.8) .250 .189 6 Double Pole (1.6) Typ .063 (2.4) Typ .095 3 6 2 5 1 4 CL Single color LED & isolated bicolor LED switches do not have terminal 5. (7.9) Typ .311 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 Touch Straight PC with Turret LED Terminal Keylocks (4.8) .189 Thk = (0.8) Typ .031 03 Epoxy Seal (1.57) Typ .062 Slides Solder Lug with Turret LED Terminal Tilt 01 Programmable Illuminated PB TERMINALS AT2107 Bezel for Snap-in Panel Frame (11.8) .465 Finish: Matte (12.0) .472 (15.6) .614 Black B White (13.1) .516 (21.5) .846 E Yellow www.nkk.com Accessories (15.9) .626 (2.2) .087 F Green G Blue H Supplement Material: Polyamide A Indicators OPTIONAL BEZEL & COLORS Colors Available: Rotaries W Rockers Toggles LED Tipped Rockers & Paddles Gray B97