s5106 etc kpin1033e

PHOTODIODE
Si PIN photodiode
S5106, S5107, S7509, S7510
Chip carrier package for surface mount
S5106, S5107, S7509 and S7510 are Si PIN photodiodes sealed in chip carrier packages suitable for surface mount using automated solder
reflow techniques. These photodiodes have large active areas, making them suitable for spatial light transmission where a wide field-of-view
angle is required. Other applications include POS scanners, power meters and analytical instruments.
Features
Applications
l Active area
l Spatial light transmission
l Laser radar
l Power meter
l Bar-code reader
S5106: 5 × 5 mm
S5107: 10 × 10 mm
S7509: 2 × 10 mm
S7510: 6 × 11 mm
l Ceramic chip carrier package for surface mount
l Suitable for solder reflow
l High sensitivity
■ General ratings / Absolute maximum ratings
Type No.
S5106
S5107
S7509
S7510
Dimensional
outline/
Window
material *
➀/R
➁/R
➂/R
➃/R
Active
area size
Effective
active area
(mm)
5×5
10 × 10
2 × 10
6 × 11
(mm2)
25
100
20
66
Reverse
voltage
VR Max
(V)
Absolute maximum ratings
Power
Operating
Storage
dissipation temperature temperature
P
Topr
Tstg
(mW)
(°C)
(°C)
30
50
-40 to +100
-40 to +125
■ Electrical and optical characteristics (Typ. Ta=25 °C, unless otherwise noted)
Type No.
Spectral Peak
response sensitivity
range wavelength
λp
λ
(nm)
S5106
S5107
320 to 1100
S7509
S7510
* Window R: Resin coating
Photo sensitivity
S
(A/W)
λp 660 n m 780 n m 830 n m
(nm)
960
0.72 0.45 0.57 0.62
Short
circuit
current
Isc
100 lx
(µA)
27
110
22
72
Cut-off Terminal
Dark
Temp.
frequency capacitance
current
coefficient
fc
Ct
ID
of ID
RL=50 Ω f=1 MHz
TCID
VR=10 V
VR=10 V VR=10 V
Typ. Max.
(nA) (nA) (times/°C) (MHz)
(pF)
0.4 5
20
40
0.9 10
10
150
1.15
0.5 5
20
40
1.0 10
15
80
NEP
VR=10 V
λ=λp
(W/Hz1/2)
1.6 × 10-14
2.4 × 10-14
1.7 × 10-14
2.5 × 10-14
Note) S5106, S7509: For mass production, order unit is 100 pieces.
S5107, S7510: For mass production, order unit is 50 pieces.
1
Si PIN photodiode
■ Spectral response
■ Photo sensitivity temperature characteristic
(Typ. Ta=25 ˚C)
PHOTO SENSITIVITY (A/W)
0.7
0.6
0.5
0.4
0.3
0.2
0.1
400
600
800
(Typ.)
+1.5
TEMPERATURE COEFFICIENT (%/˚C)
0.8
0
200
S5106, S5107, S7509, S7510
+1.0
+0.5
0
-0.5
200
1000
400
600
800
1000
WAVELENGTH (nm)
WAVELENGTH (nm)
KPINB0093EC
KPINB0165EA
■ Dark current vs. reverse voltage
■ Terminal capacitance vs. reverse voltage
(Typ. Ta=25 ˚C)
DARK CURRENT
1 nA
100 pA
S5107, S7510
S7509
(Typ. Ta=25 ˚C, f=1 MHz)
10 nF
TERMINAL CAPACITANCE
10 nA
S5106
10 pA
1 nF
S5107
S7510
100 pF
S5106
S7509
1 pA
0.1
1
10
100
REVERSE VOLTAGE (V)
1
10
100
REVERSE VOLTAGE (V)
KPINB0166EA
2
10 pF
0.1
KPINB0128EA
Si PIN photodiode
S5106, S5107, S7509, S7510
■ Dimensional outlines (unit: mm)
➀ S5106
➁ S5107
8.80 ± 0.2
14.5 ± 0.2
(4 ×) R0.3
ACTIVE AREA
SILICONE
RESIN
1.5
3.0
1.8
0.46
0.46
PHOTOSENSITIVE
SURFACE
2.5
SILICONE
RESIN
1.5
PHOTOSENSITIVE
SURFACE
1.26 ± 0.15
INDEX MARK
1.26 ± 0.15
16.5 ± 0.2
10.6 ± 0.2
(4 ×) R0.3
ACTIVE AREA
1.8
(10 ×) 1.2
(10 ×) 0.6
1.27
2.54
NC (excluding pins
)
Burrs shall protrude no more than 0.3 mm
on any side of package.
NC (excluding pins
)
Burrs shall protrude no more than 0.3 mm
on any side of package.
KPINA0002EF
➂ S7509
KPINA0013EC
➃ S7510
15.35
(4 ×) R0.3
ACTIVE AREA
ACTIVE AREA
PHOTOSENSITIVE
SURFACE
SILICONE
RESIN
1.26 ± 0.15
11.5 ± 0.2
1.26 ± 0.15
SILICONE
RESIN
0.46
6.50
PHOTOSENSITIVE
SURFACE
14.8 ± 0.2
0.46
(4 ×) R0.25
(18 ×) 0.6
2
2
2
(16 ×) 0.6
2
1.27
NC (excluding pins
)
Burrs shall protrude no more than 0.3 mm
on any side of package.
1.27
NC (excluding pins
)
Burrs shall protrude no more than 0.3 mm
on any side of package.
KPINA0055EB
KPINA0056EB
3
Si PIN photodiode
S5106, S5107, S7509, S7510
Precautions for use
● The light input window of this product uses soft silicone resin. Avoid touching the window to keep it from grime and damage that
can decrease sensitivity. External force applied to the resin surface may deform or cut off the wires, so do not touch the window
to prevent such troubles.
● Use rosin flux when soldering, to prevent the terminal lead corrosion. Reflow oven temperature should be at 260 °C maximum for 5
seconds maximum time under the conditions that no moisture absorption occurs.
Reflow soldering conditions differ depending on the type of PC board and reflow oven. Carefully check these conditions before use.
● Silicone resin swells when it absorbs organic solvent, so do not use any solvent other than alcohol.
● Avoid unpacking until you actually use this product to prevent the terminals from oxidation and dust deposits or the coated resin
from absorbing moisture.
When the product is stored for 3 months while not unpacked or 24 hours have elapsed after unpacking, perform baking in
nitrogen atmosphere at 150 °C for 3 to 5 hours or at 120 °C for 12 to 15 hours before use.
Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions.
Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2007 Hamamatsu Photonics K.K.
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, www.hamamatsu.com
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741
4
Cat. No. KPIN1033E05
Dec. 2007 DN