InFrame™ Interior Framing System Brings Beauty and Expertise to the Inside Open space is one of the most desired features in today’s commercial buildings, and design professionals are incorporating broad expanses of glass into interior spaces. Kawneer is bringing its expertise inside with InFrame™ Interior Framing. Able to be configured to meet various project requirements, InFrame™ Interior Framing is sturdy yet adaptable and allows more light to fill interior spaces. Available as screw-spline construction and a center-aligned glass pane, InFrame™ Interior Framing meets the design needs of a range of building applications – both new and retrofit construction. With Kawneer as a single source for both exterior and interior framing and InFrame™’s break through design, performance and beauty, walls are no longer barriers. Performance Fabrication and Installation InFrame™ Interior Framing System brings the proven performance and expertise of Kawneer exterior framing products inside. The system is easily configured to meet a vast array of project requirements and is available as screw-spline construction and flush-glazed, center-aligned glass. It accommodates 1/4" infill within 2" x 6" sightlines. InFrame™ Interior Framing is sturdy, yet adaptable, with a full-perimeter bulb gasket designed to capture drywall and accommodate variations in drywall thickness, allowing for common inconsistencies, including screw heads and uneven mudding. Screw-spline fabrication, a foundation for many of Kawneer’s exterior products, means configurations of InFrame™ Interior Framing are easy to fabricate and contractors can leverage existing installation experience and knowledge. Two-piece perimeter profiles that capture drywall simplify and speed the installation process. InFrame™ Interior Framing is engineered to integrate easily with Kawneer entrances, allowing seamless incorporation of our standard or speciality entrances. Delivering the quality and knowledge Kawneer is known for, architects, contractors and owners can be assured of structural integrity and solid performance levels for both interior and exterior framing, ensuring consistency throughout the project – from design to installation. Aesthetics A selection of features come together to deliver streamlined, open interiors, making InFrame™ Interior Framing an excellent option for architects, designers and owners. Wraparound perimeter profiles deliver clean lines and eliminate the need to finish drywall terminations. InFrame™ transitions seamlessly from fixed framing to operable doors, providing enhanced design flexibility. An optional 4" tall sill member is available for a greater range of design possibilities for specific project requirements and architectural styles. For the Finishing Touch InFrame™ Interior Framing is available in anodized finishes and fluoropolymer painted finishes in a variety of colors. All anodic finishes by Kawneer meet the requirements of the Aluminum Association DAF-45 and AAMA 611 for anodized architectural aluminum. Fluoropolymer finishes meet or exceed the AAMA 2604 specification. Solvent-free powder coatings add the “green” element with high performance durability and scratch resistance that meet the standards of AAMA 2604. InFrame™ Interior Framing System captures standard commercial drywall and uses wraparound perimeter profiles with a bulb gasket design to provide additional adjustments for drywall thickness variations. Kawneer Company, Inc. Technology Park / Atlanta 555 Guthridge Court Norcross, GA 30092 © Kawneer Company, Inc. 2014 kawneer.com kawneergreen.com 770 . 449 . 5555 LITHO IN U.S.A. Form No. 14-2194 InFrameTM JULY, 2014 FEATURES Features • • • • • • 2" x 6" sightline, interior partition framing Flush glazed, center plane glass application Screw spline fabrication 1/8", 1/4", and 3/8" infill options PermanodicTM anodized finishes in seven choices Painted finishes in standard and custom choices Product Applications • Interior framing system • Integrated entrance framing allowing Kawneer standard entrances or other specialty entrances to be incorporated © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-063 For specific product applications, Consult your Kawneer representative. ADMC140 1 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. InFrameTM BLANK PAGE ADMC140 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 JULY, 2014 EC 97911-063 InFrameTM JULY, 2014 EC 97911-063 3 INDEX BASIC FRAMING MEMBERS.............................................................. 4 ENTRANCE FRAMING.................................................................... 5 - 6 MISCELLANEOUS FRAMING.............................................................. 7 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Architects - Most extrusion and window types illustrated in this catalog are standard products for Kawneer. These concepts have been expanded and modified to afford you design freedom. Some miscellaneous details are non-standard and are intended to demonstrate how the system can be modified to expand design flexibility. Please contact your Kawneer representative for further assistance. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI ) units are found in these details: m –meter cm – centimeter mm –millimeter s –second Pa –pascal MPa –megapascal Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement. ADMC140 17/32" (13.5) 1/4" (6.4) 530018 6" (152.4) D.L.O. 530015 PARTITION SILL 7 4-7/8" MIN. — 5-1/16" MAX. (123.8 MIN. — 128.6 MAX.) D.L.O. (123.8 MIN. — 128.6 MAX.) D.L.O. D.L.O. 19/32" REF. (15.1) 1 OPP. 7 1 5 6 ELEVATION IS NUMBER KEYED TO DETAILS 3/8" (9.5) NOM. 1" (25.4) 530504 530021 530012 530010 2" (50.8) 19/32" REF. (15.1) ADMC140 D.L.O. INTERMEDIATE HORIZONTAL 5 STANDARD SILL 6 D.L.O. 2 INTERMEDIATE VERTICAL 530018 530016 2" (50.8) STACK INTERMEDIATE VERTICAL 3 6" (152.4) 530018 530012 6" (152.4) 530011 530013 © Kawneer Company, Inc., 2014 BASIC FRAMING DETAILS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 4 12' FRAMING MAX. HEIGHT InFrameTM Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. * 6" (152.4) 2 2" (50.8) 3 D.L.O. 6" (152.4) 4 2" (50.8) 4-7/8" MIN. — 5-1/16" MAX. NOM. 530016 2" (50.8) REF. 5/8" (15.9) 17/32" (13.5) 530504 6" (152.4) *Note: 530504 snap-in stop with gasket can be mitered at these corners. 1" (25.4) 3/8" (9.5) JAMB 1 2 NOM. HEAD 530016 1 REF. 4 2" (50.8) REF. * 1-1/8" (28.6) 1/4" (6.4) D.L.O. 19/32" REF. (15.1) 5/8" (15.9) 530504 D.L.O. (123.8 MIN. — 128.6 MAX.) 4-7/8" MIN. — 5-1/16" MAX. SCALE 3" = 1'-0" 5/8" (15.9) 2" (50.8) 17/32" (13.5) 4 JULY, 2014 EC 97911-063 * 530022 D.L.O. (123.8 MIN. — 128.6 MAX.) 8A *Note: 530504 snap-in stop with gasket can be mitered at these corners. D.L.O. 5/8" (15.9) REF. 1 OPP. 7 * 9 6 069177 530020 2" (50.8) 530020 2" (50.8) D.O. DOOR JAMB 8 5/16" (7.9) NOM. 1-1/16" (27) 530504 069177 D.O. DOOR JAMB 9 ADMC140 5/8" (15.9) REF. 4-7/8" MIN. — 5-1/16" MAX. (123.8 MIN. — 128.6 MAX.) 069177 ELEVATIONS ARE NUMBER KEYED TO DETAILS 6" (152.4) HEAD AT DOOR 10 530021 530021 069177 530022 530024 D.O. 530020 2" (50.8) 8A D.L.O. DOOR JAMB 1-1/16" (27) 5/16" (7.9) NOM. 530504 530020 2" (50.8) 17/32" (13.5) 6" (152.4) 8 * SEE DOOR SECTIONS FOR MAX HEIGHT EC 97911-063 D.O. 4 12' FRAMING MAX. HEIGHT. 10 6" (152.4) * 6" (152.4) 19/32" REF. (15.1) 2 4-7/8" MIN. — 5-1/16" MAX. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1 17/32" (13.5) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JULY, 2014 InFrameTM 5 ENTRANCE FRAMING DETAILS SCALE 3" = 1'-0" 19/32" REF. (15.1) InFrameTM JULY, 2014 ENTRANCE FRAMING DETAILS EC 97911-063 17/32" (13.5) SCALE 3" = 1'-0" 9 OPP. 6" (152.4) *Note: 530504 snap-in stop with gasket can be mitered at these corners. 14 HEAD / TRANSOM AT COMMON STRIKE JAMB 6" (152.4) ELEVATION IS NUMBER KEYED TO DETAILS D.L.O. 450022 279001 061222 1-1/4" (31.8) D.O. 1-1/4" (31.8) 1-1/4" (31.8) 530502 279001 D.L.O. D.L.O. 12 COMMON STRIKE JAMB ABOVE TRANSOM 450022 279001 061222 049064 15A ALTERNATE BAR WITH C.O.C. FOR L.C.N. CLOSER 069177 6" (152.4) D.O. 061222 2" (50.8) D.O. 11 COMMON STRIKE JAMB (OFFSET PIVOT ONLY) ADMC140 450022 279001 2" (50.8) D.L.O. 069177 6" (152.4) TRANSOM JAMB 061222 2" (50.8) 6" (152.4) D.L.O. D.L.O. 450022 2" (50.8) 450022 D.O. 450022 TRANSOM BAR WITH C.O.C. OR STD. SURFACE CLOSER 061222 041045 15B ALTERNATE TRANSOM BAR WITH C.O.C. FOR STD. KAWNEER CLOSER © Kawneer Company, Inc., 2014 6" (152.4) 13 15 6" (152.4) 279001 279001 530020 2" (50.8) 069177 D.O. REF. (123.8 MIN. — 128.6 MAX.) 17/32" (13.5) 4-7/8" MIN. — 5-1/16" MAX. 19/32" (15.1) 5/8" (15.9) NOM. 1-1/16" (27) 530504 2" (50.8) 5/16" (7.9) NOM. REF. 5/8" (15.9) 530502 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 11 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 9 530504 15 15A 15B 530016 13 OPP. 2" (50.8) 12 12' FRAMING MAX. HEIGHT. 13 19/32" REF. (15.1) (123.8 MIN. — 128.6 MAX.) * 4 D.O. 14 SEE DOOR SECTIONS FOR MAX HEIGHT * 4-7/8" MIN. — 5-1/16" MAX. 1" (25.4) 3/8" (9.5) 6 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1/4" (6.4) 4" (101.6) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 InFrameTM EC 97911-063 MISCELLANEAOUS FRAMING 6" (152.4) 530018 027366 530019 530013 ALTERNATE HEIGHT SILL ADMC140 7 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. InFrameTM BLANK PAGE ADMC140 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 8 JULY, 2014 EC 97911-063