DATA SHEET Part No. AN5832SA Package Code No. SSOP032 - P - 0300AP SEMICONDUCTOR COMPANY MATSUSHITA ELECTRIC INDUSTRIAL CO., LTD. Publication date: February 2005 SDB00096AEB 1 AN5832SA Contents Features …………………………………………………………………………………………………………….. 3 Applications ………………………………………………………………………………………………………… 3 Package ……………………………………………………………………………………………………………. 3 Application Circuit …………………………………………………………………………………………………. 4 Block Diagram ………………...……………………………………………………………………………………. 6 Pin Descriptions ………………...…………………………………………………………………………………… 7 Absolute Maximum Ratings ………………………………………………………………………………………. 8 Operating Supply Voltage Range ……………..…………………………………………………………………. 8 SDB00096AEB 2 AN5832SA AN5832SA Silicon Monolithic Bipolar IC Features y Supports both I2C bus and parallel control y Integrated SIF demodulation y Fully adjustment - free ( when used with SIF input ) 2 adjustment points when used with baseband input y Integrated voice AGC circuit y Reduced peripheral component count y Low power consumption ( typ. VCC = 5 V, ITOT = 28 mA ) y Near pin to pin compatible with AN5833SA ( Japanese TV audio multiplex demodulation IC ) Applications y TV sets, VCRs, DVD recorders, PCs, car navigation systems, and similar products for US market Package y DIL-32PIN Plastic Package (SO Type) SDB00096AEB 3 AN5832SA Application Circuit < Instructions of Application Circuits > 1 ) In case of using base band input, ICs were adjusted to perform good separation when input level ismatched with 100 mV[rms] ( = 283 mV[p-p] ) on condition of mono 100% mod pre-emphasis OFF. However, if good enough separation can't be taken in the cause of un-matching frequency characteristic and so in input signal, it can adjust separation by connecting a volume between #22Pin and GND for adjusting high frequency separation. If it not need adjusting separation, please open #22Pin. If it need adjusting low frequency separation also, please adjust the input level volume for taking best separation on low frequency. 2 ) In case of using SIF input, please set up the SIF input level from tuners between 80 dBµV to 110 dBµV in standard RF input conditions. Please select SIF - BPFs that group delay of 4.5 MHz ±42 kHz is flat as possible. 3 ) In measuring characteristics of separation, please use the stereo modulator that perform good characteristic on dbx encoder and corrected well. In case of using SIF input, please correct FM modulation band to ±25 kHz exactly at mono 100% mod pre-emphasis OFF with the 0 carrier method. And, please use LPFs that reduce 30 kHz signal over 20 dB setting between line-outs and AB level meter SDB00096AEB 4 AN5832SA Application Circuit ( continued ) ( 1 ) Example of No Adjustments Application Circuits in case of SIF Input ( 2 ) Example of Adjustments Application Circuits in case of Base Band Input SDB00096AEB 5 AN5832SA Block Diagram SDB00096AEB 6 AN5832SA Pin Descriptions Pin No. Function 1 N. C. 2 Wide band timing 3 Wide band DET 4 Wide band DET 5 Spectral DET 6 Spectral DET 7 I2C Spectral DET 8 Spectral DET 9 MODE SW 10 Force monaural SW 11 Mute SW 12 SIF / Base band SW 13 SAP Noise DET 14 SAP DET 15 L + R REF 16 N. C. 17 Pilot DET 18 Stereo PLL filter 19 VCC 20 N. C. 21 SIF IN 22 SIF REF 23 STEREO REF 24 SDA / SAPID 25 Ground 26 PE 27 SCL / STID 28 AGC DET 29 Right - channel output 30 Left - channel output 31 N. C. 32 L - R REF SDB00096AEB 7 AN5832SA Absolute Maximum Ratings No. Parameter Symbol Rating Unit Note 1 Storage temperature Tstg –55 to +125 °C *1 2 Operating ambient temperature Topr –20 to +85 °C *1 3 Operating ambient atmospheric pressure Popr 1.013 × 105 ± 0.61 × 105 Pa 4 Operating constant gravity Gopr 9 810 m/s2 5 Operating shock Sopr 4 900 m/s2 6 Supply voltage VCC 6.0 V 7 Supply current ICC 38 mA 8 Power dissipation PD 228 mW Ta = 85°C Note ) *1 : Ta = 25°C except storage temperature, and operating ambient temperature. *2 : To use this products including dbx - TV noise reduction need the license agreement with THAT corporation. Operating Supply Voltage Range Operating supply voltage range VCC SDB00096AEB 4.5 V to 5.5 V 8 Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technical information described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2003 SEP