ZARLINK ZL50073

ZL50073
32 K Channel Digital Switch with High Jitter
Tolerance, Rate Conversion per Group of
4 Streams (8, 16, 32 or 64 Mbps),
and 128 Inputs and 128 Outputs
Data Sheet
Features
•
April 2005
32,768 channel x 32,768 channel non-blocking
digital Time Division Multiplex (TDM) switch at
65.536 Mbps, 32.768 Mbps and 16.384 Mbps or
using a combination of rates
Ordering Information
ZL50073GAC
484 Ball PBGA
•
16,384 channel x 16,384 channel non-blocking
digital TDM switch at 8.192 Mbps
•
High jitter tolerance with multiple input clock
sources and frequencies
•
•
Up to 128 serial TDM input streams, divided into
32 groups with 4 input streams per group
Per-channel constant or variable throughput delay
for frame integrity and low latency applications
•
Per-stream Bit Error Rate (BER) test circuits
•
Up to 128 serial TDM output streams, divided into
32 groups with 4 output streams per group
•
Per-channel high impedance output control
•
Per-channel force high output control
Per-group input and output data rate conversion
selection at 65.536 Mbps, 32.768 Mbps,
16.384 Mbps and 8.192 Mbps. Input and output
data group rates can differ
•
Per-channel message mode
•
Control interface compatible with Intel and
Motorola Selectable 32 bit and 16 bit nonmultiplexed buses
•
-40°C to +85°C
•
Per-group input bit delay for flexible sampling
point selection
•
Connection Memory block programming
•
Per-group output fractional bit advancement
•
•
Four sets of output timing signals for interfacing
additional devices
Supports ST-BUS and GCI-Bus standards for
input and output timing
•
IEEE 1149.1 (JTAG) test port
•
Per-channel A-Law/µ-Law Translation
•
3.3 V I/O with 5 V tolerant inputs; 1.8 V core
voltage
STiA0
STiB0
STiC0
STiD0
ODE
Data Memory
Connection Memory
Output
Timing
Test Access
Port
TRST
A18-0
DTA
WAIT
BERR
D31-0
Microprocessor Interface
and Control Registers
IM
DS
CS
R/W
SIZ1-0
D16B
Timing
SToA0
SToB0
SToC0
SToD0
SToA31
SToB31
SToC31
SToD31
:
:
Input
Timing
FPo3-0
CKo3-0
P/S
Converter
S/P
Converter
STiA31
STiB31
STiC31
STiD31
FPi2-0
CKi2-0
CK_SEL1-0
PWR
TMS
TDi
TDo
TCK
:
:
VSS
Output
Group 31
Input
Group 31
VDD_IO
Output
Group 0
Input
Group 0
VDD_CORE
Figure 1 - ZL50073 Functional Block Diagram
1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 2004-2005, Zarlink Semiconductor Inc. All Rights Reserved.
ZL50073
Data Sheet
Applications
•
Large Switching Platforms
•
Central Office Switches
•
Wireless Base Stations
•
Multi-service Access Platforms
•
Media Gateways
Description
The ZL50073 is a non-blocking Time Division Multiplex (TDM) switch with maximum 32,768 x 32,768 channels. The
device can switch 64 kbps and Nx64 kbps TDM channels from any input stream to any output stream. With a
number of enhanced features, the ZL50073 is designed for high capacity voice and data switching applications.
The ZL50073 has 128 input and 128 output data streams which can operate at 8.192 Mbps, 16.384 Mbps,
32.768 Mbps or 65.536 Mbps. The large number of inputs and outputs maintains full 32 K x 32 K channel switching
capacity at bit rates of 65 Mbps, 32 Mbps and 16 Mbps. Up to 32 input and output data streams may operate at
65 Mbps. Up to 64 input and output data streams may operate at 32 Mbps. Up to 128 input and output data streams
may operate at 16 Mbps or 8 Mbps. The data rate can be independently set in groups of 4 input or output streams.
In this way it is possible to provide rate conversion from input data channel to output data channel.
The ZL50073 uses a master clock (CKi0) and frame pulse (FPi0) to define the TDM data stream frame boundary
and timing. A high speed system clock is derived internally from CKi0 and FPi0. The input and output data streams
can independently reference their timings to one of the input clocks or to the internal system clock.
The ZL50073 has a variety of user configurable options designed to provide flexibility when data streams are
connected to multiple TDM components or circuits. These include:
•
Two additional programmable reference inputs, CKi2 - 1 and FPi2 - 1, which can be used to provide
alternative sources for input and output stream timing
•
Variable input bit delay and output advancement, to accommodate delays and frame offsets of streams
connected through different data paths
•
Four timing outputs, CKo3 - 0 and FPo3 - 0, which can be configured independently to provide a variety of
clock and frame pulse options
•
Support of both ST-BUS and GCI-Bus formats
The ZL50073 also has a number of value added features for voice and data applications:
•
Per-channel variable delay mode for low latency applications and constant delay mode for frame integrity
applications
•
Per-channel A-Law/µ-Law Conversions for both voice and data
•
128 separate Pseudo-random Bit Sequence (PRBS) test circuits; one per stream. This provides an integrated
Bit Error Rate (BER) test capability to facilitate data path integrity checking
The ZL50073 has two major modes of operation: Connection Mode (normal) and Message Mode. In Connection
Mode, data bytes received at the TDM inputs are switched to timeslots in the output data streams, with mapping
controlled by the Connection Memories. Using Zarlink's Message Mode capability, microprocessor data can be
broadcast to the output data streams on a per-channel basis. This feature is useful for transferring control and
status information to external circuits or other TDM devices.
A non-multiplexed microprocessor port provides access to the internal Data Memory, Connection Memory and
Control Registers used to program ZL50073 options. The port is configurable to interface with either Motorola or
Intel-type microprocessors and is selectable to be either 32 bit or 16 bit.
The mandatory requirements of IEEE 1149.1 standard are supported via the dedicated Test Access Port.
2
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Table of Contents
1.0 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.2 Switch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.3 Stream Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.4 Input and Output Rate Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.4.1 Per Group Rate Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.5 Rate Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.0 Input Clock (CKi) and Input Frame Pulse (FPi) Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.0 Output Clock (CKo) and Output Frame Pulse (FPo) Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.0 Output Channel Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.0 Data Input Delay and Data Output Advancement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1 Input Sampling Point Delay Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2 Fractional Bit Advancement on Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.0 Message Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.1 Data Memory Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.2 Connection Memory Block Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.0 Data Delay Through the Switching Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.1 Constant Delay Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.2 Variable Delay Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.0 Per-Channel A-Law/m-Law Translation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9.0 Bit Error Rate Tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
10.0 Microprocessor Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
10.1 Addressing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
10.2 32 bit Bus Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.3 16 Bit Bus Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10.4 Bus Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
10.4.1 Read Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
10.4.2 Write Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
11.0 Power-up and Initialization of the ZL50073 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
11.1 Device Reset and Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
11.2 Power Supply Sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
11.3 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
12.0 IEEE 1149.1 Test Access Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
12.1 Test Access Port (TAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
12.2 Instruction Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
12.3 Test Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
12.4 Boundary Scan Description Language (BSDL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
13.0 Memory Map of ZL50073 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
14.0 Detailed Memory and Register Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
14.1 Connection Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
14.1.1 Connection Memory Bit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
14.1.2 Connection Memory LSB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
14.2 Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
14.3 BER Control Memory and Error Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
14.3.1 Input BER Enable Control Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
14.3.2 BER Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
14.4 Group Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
14.5 Input Clock Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
14.6 Output Clock Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
14.7 Block Init Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Table of Contents
14.8 Block Init Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
15.0 DC/AC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
List of Figures
Figure 1 - ZL50073 Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2 - 32 K x 32 K Channel Basic Switch Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 3 - ZL50073 32 K x 32 K Channel and Stream Provisioning Example at Multiple Rates . . . . . . . . . . . . . . 17
Figure 4 - Input and Output Data Rate Conversion Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 5 - Input Sampling Point Delay Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 6 - Output Bit Advancement Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 7 - Data Throughput Delay for Constant Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 8 - Data Throughput Delay for Variable Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 9 - Example PRBS Timeslot Insertion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 10 - Read Cycle Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 11 - Write Cycle Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 12 - Frame Pulse Input and Clock Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 13 - Frame Skew Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 14 - ST-Bus Frame Pulse and Clock Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 15 - GCI Frame Pulse and Clock Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 16 - Serial Data Timing to CKi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 17 - Serial Data Timing to CKo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 18 - CKo to other CKo Skew. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 19 - Microprocessor Bus Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 20 - Intel Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 21 - IEEE 1149.1 Test Port & PWR Reset Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
5
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
List of Tables
Table 1 - Data Rate and Maximum Switch Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 2 - TDM Stream Bit Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 3 - CKi0 and FPi0 Setting via CK_SEL1 - 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 4 - Input and Output Voice and Data Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 5 - Example of Address and Byte Significance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 6 - 32 Bit Motorola Mode Byte Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 7 - 32 Bit Motorola Mode Access Transfer Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 8 - 32 bit Intel Mode Bus Enable Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 9 - Byte Enable Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 10 - 16 Bit Mode Word Alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 11 - 16 Bit Mode Example Byte Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 12 - Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 13 - Connection Memory Group Address Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 14 - Connection Memory Stream Address Offset at Various Output Rates . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 15 - Connection Memory Timeslot Address Offset Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 16 - Connection Memory Bits (CMB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 17 - Connection Memory LSB Group Address Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 18 - Connection Memory LSB Stream Address Offset at Various Output Rates . . . . . . . . . . . . . . . . . . . . . 39
Table 19 - Data Memory Group Address Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table 20 - Data Memory Stream Address Offset at Various Output Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table 21 - BER Enable Control Memory Group Address Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 22 - BER Enable Control Memory Stream Address Offset at Various Output Rates . . . . . . . . . . . . . . . . . . 42
Table 23 - BER Counter Group and Stream Address Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 24 - Group Control Register Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 25 - Group Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 26 - Input Clock Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 27 - Output Clock Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 28 - Block and Power-up Initialization Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Change Summary
The following table captures the changes from the July 2004 issue.
Page
Item
Change
12
"Pin Description" - CKo0-3
Added special requirement for using output clock at
65.536 MHz.
13
"Pin Description" - DTA, WAIT
Added more detailed description to the DTA and WAIT
pins.
53
“AC Electrical Characteristics1 - FPi0-2
and CKi0-2 Timing“
Added tFPIS, tFPIH (input frame pulse setup and hold)
maximum values.
55
Figure 13 "Frame Skew Timing Diagram"
Added FPi1,2 frame pulse to Figure “Frame Skew Timing
Diagram” to clarify frame boundary skew.
56
(1) “AC Electrical Characteristics1 FPO0-3 and CKO0-3 (65.536 MHz)
Timing“
(2) “AC Electrical Characteristics1 FPO0-3 and CKO0-3 (32.768 MHz)
Timing“
(3) “AC Electrical Characteristics1 FPO0-3 and CKO0-3 (16.384 MHz)
Timing“
(4) “AC Electrical Characteristics1 FPO0-3 and CKO0-3 (8.192 MHz)
Timing“
Added CKO0-3 and FPO0-3 setup and hold parameters for
all different clock rates.
57
“AC Electrical Characteristics - Output
Clock Jitter Generation“
Added this table to specify CKO0-3 jitter generation.
58
“AC Electrical Characteristics1 - Serial
Data Timing2 to CKi“
(1) Values of parameters tSIPS, tSIPH, tSINS, tSINH, tSINV,
tSIPV, tSIPZ and tSINZ are revised.
(2) Separated parameter tCKD into tCKDP and tCKDN.
59
Figure 16 "Serial Data Timing to CKi"
Added more detail to figure.
60
“AC Electrical Characteristics - Serial
Data Timing1 to CKo2“
Values of parameters tSOPS, tSOPH, tSONS, tSONH, tSOPV,
tSONV, tSOPZ and tSONZ are revised.
61
Figure 17 "Serial Data Timing to CKo"
Added more detail to figure.
62
“AC Electrical Characteristics - CKo to
Other CKo Skew1“
Added CKO skew parameters, tCKOS.
62
Figure 18 "CKo to other CKo Skew"
Added figure to show tCKOS.
7
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Pin Diagram - ZL50073 23 mm x 23 mm 484 Ball PBGA (as viewed through top of package)
A1 corner identified by metallized marking.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
A[1]
IC
DTA
20
21
22
A
CKo
[0]
STiA D[30] D[25] D[20] D[16] D[15] D[11]
[0]
D[7]
D[4]
D[0]
A[18] A[14] A[10]
A[7]
A[2]
B
SToB STiD SToA D[31] D[26] D[21] D16B D[13]
[1]
[1]
[0]
D[9]
D[5]
D[3]
A[17] A[11]
A[8]
A[6]
A[0] BERR SIZ[0] SToB STiA
[31] [31]
C
STiA
[2]
D[27] D[22] D[19] D[12]
D[6]
D[1]
A[15]
A[9]
A[3]
R/W
CS
D
STiC STiD SToC SToD SToB STiC D[28] D[23] D[17]
[3]
[2]
[1]
[0]
[0]
[0]
D[8]
A[16] A[13]
A[5]
DS
WAIT SToD STiB
[31] [31]
E
STiD SToB STiC SToA STiA SToC STiB D[24] D[18] D[14]
[4]
[3]
[2]
[1]
[1]
[0]
[0]
D[2]
A[4]
CKo SIZ[1] STiC TMS SToC STiD SToD STiA
[3]
[31]
[30] [30] [29] [29]
F
SToB SToC SToB SToD STiC
[4]
[3]
[2]
[1]
[1]
VSS
VDD_
CORE
G
SToD SToD SToD STiB
[4]
[3]
[2]
[2]
VDD_
VSS
H
STiA
[5]
STiA STiD SToC SToA VDD_ VDD_
[4]
[3]
[2]
[2] CORE
IO
J
STiB
[5]
CKi
[1]
K
SToB STiD
[5]
[5]
VSS
VDD_
CORE
VSS
VSS
VSS
VSS
VSS
VSS
VDD_
CORE
VDD_ VDD_ SToA
IO
CORE [27]
L
ODE SToD SToC STiD STiC VDD_ VDD_
[5]
[5]
[6]
[5] CORE
IO
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD_
CORE
SToD STiC STiB
[26] [26] [26]
M
STiA
[6]
STiB STiC STiC SToA VDD_ VDD_ VDD_
[6]
[6]
[7]
[5]
IO
CORE
IO
VSS
VSS
VSS
VSS
VSS
VSS
VDD_
VSS
IO
VDD_ STiA STiD SToB SToA
[25] [25] [25] [25]
IO
N
SToB SToC SToD SToA SToA
[6]
[6]
[6]
[7]
[6]
VDD_ SToD SToC STiD SToB STiB STiC
[23] [24] [24] [24] [25] [25]
IO
P
STiA
[7]
R
STiD SToC
[7]
[7]
T
SToD
[7]
U
STiC SToD STiC STiA SToC
[8]
[8]
[9]
[10] [10]
V
STiD STiB SToC SToB SToD SToB STiC STiB SToA STiC SToB SToC
[8]
[9]
[9]
[10] [10]
[11]
[12] [13] [13] [15] [16] [16]
IC
CK_ STiB SToA STiA SToB SToD SToC SToA STiA
SEL[1] [18] [19] [20] [20] [20] [21] [22] [23]
W
STiA SToB STiD STiA SToA STiB SToD STiC STiA SToD SToC
[9]
[9]
[10]
[11]
[11]
[12] [12] [13] [14] [14] [15]
IC
SToB CK_ SToC STiD SToD STiD STiC STiA SToB
[17] SEL[0] [18] [19] [19] [20] [21] [22] [22]
Y
SToA SToA STiB SToC SToA
[9]
[10]
[11]
[11]
[12]
STiD STiB SToB STiD SToD SToD
[13] [14] [14] [15] [15] [16]
IC
STiC SToC STiA SToB STiB STiB SToA SToB STiB
[17] [17] [18] [18] [19] [20] [20] [21] [22]
AA
STiC STiC SToD STiD STiA SToB SToD SToA STiA SToA STiB SToA
[10]
[11]
[11]
[12] [13] [13] [13] [14] [15] [15] [16] [16]
FPi
[0]
STiA SToA
[17] [17]
AB
STiD STiA SToB CKo SToC STiC STiD SToC STiB SToB STiC STiD
[11]
[12] [12]
[1]
[13] [14] [14] [14] [15] [15] [16] [16]
NC
STiA
[3]
STiB STiD
[1]
[0]
IM
FPo
[0]
D[29] VDD_ VDD_ D[10] VDD_ VDD_ SToC VDD_
IO
CORE
IO
CORE [31]
IO
VSS
IO
VSS
STiC SToA STiB VDD_ VDD_ VDD_
[4]
[3]
[3]
IO
CORE
IO
FPi
[1]
SToC SToA STiB
[4]
[4]
[4]
VDD_
VSS
VDD_
CORE
VDD_
VSS
VSS
VSS
VSS
IO
VDD_
CORE
VDD_
VSS
VDD_
CORE
VDD_
VSS
VSS
IO
VSS
VSS
IO
STiA
[30]
STiD TRST SToD STiB STiD
[31]
[30] [30] [29]
TDi
SToB STiC SToA SToD
[30] [30] [29] [28]
STiB
[28]
VSS
VDD_
CORE
SToA SToC STiC SToB STiA
[30] [29] [29] [28] [28]
VDD_
CORE
VDD_
VSS
SToB STiB STiC
[29] [29] [28]
VSS
VDD_
CORE
SToA SToC STiD SToD STiC STiA
[28] [28] [28] [27] [27] [27]
VDD_
VSS
VDD_ SToB SToC STiB
[27] [27] [27]
IO
IO
IO
IO
FPi
[2]
CKi
[2]
IC
STiD
[27]
SToC
[26]
SToA SToB STiD
[26] [26] [26]
STiA SToD SToC
[26] [25] [25]
IC
VSS
VSS
VSS
VSS
VSS
VSS
VDD_
CORE
STiB SToB STiA SToA VDD_ VDD_ VDD_
[7]
[7]
[8]
[8] CORE
IO
IO
VSS
VSS
VSS
VSS
VSS
VSS
VDD_ VDD_ VDD_ SToA STiC STiB SToA SToD
[23] [24] [24] [24]
IO
CORE CORE [23]
VSS
VDD_
CORE
VDD_
VSS
VDD_
CORE
VDD_
VSS
VDD_
VSS
VSS
VSS
VSS
VSS
VDD_
CORE
TDo
VDD_
CORE
IC
VSS
A[12]
FPo
[3]
PWR SToA TCK
[31]
SToB STiB VDD_ VDD_
[8]
[8]
IO
CORE
SToC STiD STiB SToD
[8]
[9]
[10]
[9]
VSS
FPo
[1]
VSS
VSS
VSS
VDD_
CORE
IO
IO
VDD_
CORE
VSS
IO
VDD_
IO
VDD_
CORE
VDD_
VSS
IO
CKo
[2]
STiD STiB
[22] [23]
STiA STiC
[24] [24]
SToA
[21]
FPo SToC STiD SToC
[2]
[22] [23] [23]
VDD_ SToC VDD_ VDD_ STiA VDD_ VDD_ SToA VDD_ STiC VDD_ SToC STiD STiC SToD SToB
[12]
[19] CORE [20] [21] [22] [22] [23]
IO
IO
CORE [16]
IO
CORE [18]
IO
CKi
[0]
8
Zarlink Semiconductor Inc.
NC
IC
IC
SToD SToB SToC STiA SToD
[18] [19] [19] [21] [21]
STiB STiD SToD STiC STiD STiA STiC STiB
[17] [17] [17] [18] [18] [19] [20] [21]
ZL50073
Data Sheet
Pin Description
Pin
Name
Description
TDM Interface
F7, F10, F13, F17, G9, G12,
G15, H6, H10, H13, H16, J7,
K8, K15, K17, L6, L16, M7,
N8, N15, P6, P16, P17, R7,
R10, R13, T9, T12, T15,
U10, U13, U17
VDD_CORE
F9, F12, F15, G6, G10, G13,
G16, H7, H11, H14, J6, J8,
J15, J17, K16, L7, M6, M8,
M15, M17, N16, P7, P8,
P15, R6, R11, R14, R17,
T10, T16, U7, U9, U12, U15
VDD_IO
F6, F16, G7, G8, G11, G14,
G17, H8, H9, H12, H15, J9,
J10, J11, J12, J13, J14, J16,
K7, K9, K10, K11, K12, K13,
K14, L8, L9, L10, L11, L12,
L13, L14, L15, M9, M10,
M11, M12, M13, M14, M16,
N6, N7, N9, N10, N11, N12,
N13, N14, P9, P10, P11,
P12, P13, P14, R8, R9, R12,
R15, R16, T2, T7, T8, T11,
T13, T14, T17, U6
VSS
A2, E5, C1, C2, H2, H1, M1,
P1, P4, W1, U4, W4, AB2,
AA5, W9, AA9, U11, AA14,
Y16, AB20, V17, AA21,
W21, V22, R21, M18, L20,
H22, F22, E21, B22, B20
STiA0-31
Serial TDM Input Data ’A’ Streams (5 V Tolerant Input with
Internal Pull-down)
The data rate of these input streams can be selected in a group of 4
to be either 8.192 Mbps, 16.384 Mbps, 32.678 Mbps or
65.536 Mbps. Refer to Section 1.4 for rate programming options.
The data streams can be selected to be either inverted or
non-inverted, programmed by the Group Control Registers (Section
14.4).
Unused inputs are pulled low by internal pull-down resistors and
may be left unconnected.
E7, C3, G4, J5, K6, J1, M2,
P2, R5, V2, T5, Y3, W6, V8,
Y8, AB9, AA11, AB15, V15,
Y18, Y19, AB22, Y22, R20,
P20, N21, L19, J20, E22,
G19, C21, D17
STiB0-31
Serial TDM Input Data ’B’ Streams (5 V Tolerant Input with
Internal Pull-down)
The data rate of these input streams can be selected in a group of 4
to be either 8.192 Mbps, 16.384 Mbps or 32.678 Mbps. The stream
is unused when its input group rate is 65.536 Mbps. Refer to
Section 1.4 for rate programming options.
The data streams can be selected to be either inverted or
non-inverted, programmed by the Group Control Registers (Section
14.4).
Unused inputs are pulled low by internal pull-down resistors and
may be left unconnected.
Power Supply for the Core Logic: +1.8 V
Power Supply for the I/O: +3.3 V
Ground
9
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Pin Description (continued)
Pin
Name
Description
D6, F5, E3, D1, J3, L5, M3,
M4, U1, U3, AA1, AA2, V7,
W8, AB6, V10, AB11, Y14,
AB18, U16, AB21, W20,
U20, P19, R22, N22, L18,
H21, G20, F20, D20, E16
STiC0-31
Serial TDM Input Data ’C’ Streams (5 V Tolerant Input with
Internal Pull-down)
The data rate of these input streams can be selected in a group of 4
to be either 8.192 Mbps or 16.384 Mbps. The stream is unused
when its input group rate is 65.536 Mbps or 32.678 Mbps. Refer to
Section 1.4 for rate programming options.
The data streams can be selected to be either inverted or
non-inverted, programmed by the Group Control Registers (Section
14.4).
Unused inputs are pulled low by internal pull-down resistors and
may be left unconnected.
C4, B2, D2, H3, E1, K2, L4,
R1, V1, T4, W3, AB1, AA4,
Y7, AB7, Y10, AB12, AB16,
AB19, W17, W19, U19, R19,
T21, N19, M19, K22, G22,
H19, C22, E19, C18
STiD0-31
Serial TDM Input Data ’D’ Streams (5 V Tolerant Input with
Internal Pull-down)
The data rate of these input streams can be selected in a group of 4
to be either 8.192 Mbps or 16.384 Mbps. The stream is unused
when its input group rate is 65.536 Mbps or 32.678 Mbps. Refer to
Section 1.4 for rate programming options.
The data streams can be selected to be either inverted or
non-inverted, programmed by the Group Control Registers (Section
14.4).
Unused inputs are pulled low by internal pull-down resistors and
may be left unconnected.
B3, E4, H5, J4, K5, M5, N5,
N4, P5, Y1, Y2, W5, Y5, V9,
AA8, AA10, AA12, AA15,
U14, V16, Y20, T18, V21,
P18, P21, M21, K20, K18,
H17, D21, F18, A21
SToA0-31
Serial TDM Output Data ’A’ Streams (5 V Tolerant, 3.3 V
Tri-state Slew-Rate Controlled Outputs)
The data rate of these output streams can be selected in a group of
4 to be either 8.192 Mbps, 16.384 Mbps, 32.678 Mbps or
65.536 Mbps. Refer to Section 1.4 for rate programming options.
The data streams can be selected to be either inverted or
non-inverted, programmed by the Group Control Registers (Section
14.4).
D5, B1, F3, E2, F1, K1, N1,
P3, R4, W2, V4, V6, AB3,
AA6, Y9, AB10, V11, W14,
Y17, AA19, V18, Y21, W22,
U22, N20, M20, K21, J18,
F21, G18, D19, B19
SToB0-31
Serial TDM Output Data ’B’ Streams (5 V Tolerant, 3.3 V
Tri-state Slew-Rate Controlled Outputs)
The data rate of these output streams can be selected in a group of
4 to be either 8.192 Mbps, 16.384 Mbps or 32.678 Mbps. The
stream is unused when its output group rate is 65.536 Mbps. Refer
to Section 1.4 for rate programming options.
The data streams can be selected to be either inverted or
non-inverted, programmed by the Group Control Registers (Section
14.4).
Unused outputs are tristated and may be left unconnected.
E6, D3, H4, F2, K4, L3, N2,
R2, T3, V3, U5, Y4, U8,
AB5, AB8, W11, V12, Y15,
W16, AA20, U18, V20, T20,
T22, N18, L22, J22, J19,
H18, F19, E18, F14
SToC0-31
Serial TDM Output Data ’C’ Streams (5 V Tolerant, 3.3 V
Tri-state Slew-Rate Controlled Outputs)
The data rate of these output streams can be selected in a group of
4 to be either 8.192 Mbps or 16.384 Mbps. The stream is unused
when its output group rate is 65.536 Mbps or 32.678 Mbps. Refer to
Section 1.4 for rate programming options.
The data streams can be selected to be either inverted or
non-inverted, programmed by the Group Control Registers (Section
14.4).
Unused outputs are tristated and may be left unconnected.
10
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Pin Description (continued)
Pin
Name
Description
D4, F4, G3, G2, G1, L2, N3,
T1, U2, T6, V5, AA3, W7,
AA7, W10, Y11, Y12, AB17,
AA18, W18, V19, AA22,
U21, N17, P22, L21, L17,
H20, D22, E20, C20, D16
SToD0-31
Serial TDM Output Data ’D’ Streams (5 V Tolerant, 3.3 V
Tri-state Slew-Rate Controlled Outputs)
The data rate of these output streams can be selected in a group of
4 to be either 8.192 Mbps or 16.384 Mbps. The stream is unused
when its output group rate is 65.536 Mbps or 32.678 Mbps. Refer to
Section 1.4 for rate programming options.
The data streams can be selected to be either inverted or
non-inverted, programmed by the Group Control Registers (Section
14.4).
Unused outputs are tristated and may be left unconnected.
W12
CKi0
ST-BUS/GCI-Bus Clock Input (5 V Tolerant Schmitt-Triggered
Input)
This pin accepts an 8.192 MHz, 16.384 MHz, 32.678 MHz or
65.536 MHz clock. This clock must be provided for correct
operation of the ZL50073. The frequency of the CKi0 input is
selected by the CK_SEL1-0 inputs. The active clock edge may be
either rising or falling, programmed by the Input Clock Control
Register (Section 14.5).
AA13
FPi0
ST-BUS/GCI-Bus Frame Pulse Input (5 V Tolerant Input)
This pin accepts the 8 kHz frame pulse which marks the frame
boundary of the TDM data streams. The pulse width is nominally
one CKi0 clock period (assuming ST-BUS mode) selected by the
CK_SEL1-0 inputs. The active state of the frame pulse may be
either high or low, programmed by the Input Clock Control Register
(Section 14.5).
J2, G21
CKi1-2
ST-BUS/GCI-Bus Clock Inputs (5 V Tolerant Schmitt Triggered
Inputs)
These optional TDM clock inputs are at 8.192 MHz, 16.384 MHz,
32.678 MHz or 65.536 MHz. The frequency of each clock input is
automatically detected by the ZL50073. Refer to Section 2.0 for
TDM timing options. The active clock edge may be either rising or
falling, programmed by the Input Clock Control Register (Section
14.5). Unused inputs must be connected to a defined logic level.
K3, K19
FPi1-2
ST-BUS/GCI-Bus Frame Pulse Inputs (5 V Tolerant Inputs)
These 8 kHz input pulses correspond to the optional CKi2-1 clock
inputs. The frame pulses mark the frame boundary of the TDM data
streams. Refer to Section 2.0 for TDM timing options. Each pulse
width is nominally one CKi clock period (assuming ST-BUS mode).
The active state of the frame pulse may be either high or low,
programmed by the Input Clock Control Register (Section 14.5).
Unused inputs must be connected to a defined logic level.
11
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Pin Description (continued)
Pin
Name
Description
A1, AB4, R18, E14
CKo0-3
ST-BUS/GCI-Bus Clock Outputs (3.3 V Outputs with Slew-Rate
Control)
These clock outputs can be programmed to generate 8.192 MHz,
16.384 MHz, 32.678 MHz or 65.536 MHz TDM clock outputs. The
active edge can be programmed to be either rising or falling. The
source of the clock outputs can be derived from either the CKi2-0
inputs or the internal system clock. The frequency, active edge and
source of each clock output can be programmed independently by
the Output Clock Control Register (Section 14.6). For 65.536 MHz
output clock, the total loading on the output should not be
larger than 10pF.
G5, Y6, T19, C17
FPo0-3
ST-BUS/GCI-Bus Frame Pulse Outputs (3.3 V Outputs with
Slew-Rate Control)
These 8 kHz output pulses mark the frame boundary of the TDM
data streams. The pulse width is nominally one clock period of the
corresponding CKo output. The active state of each frame pulse
may be either high or low, independently programmed by the
Output Clock Control Register (Section 14.6).
W15, V14
CK_SEL0-1
Master Clock Input Select (5 V Tolerant Inputs)
Inputs used to select the frequency and frame alignment of CKi0
and FPi0:
CK_SEL1 = 0, CK_SEL0 = 0, 8.192 MHz
CK_SEL1 = 0, CK_SEL0 = 1, 16.384 MHz
CK_SEL1 = 1, CK_SEL0 = 0, 32.768 MHz
CK_SEL1 = 1, CK_SEL0 = 1, 65.536 MHz
L1
ODE
Output Drive Enable (5 V Tolerant Input with Internal Pull-up)
This is the asynchronous output enable control for the output
streams. When it is high, the streams are enabled. When it is low,
the output streams are tristated.
A18, J21, M22, R3, V13,
W13, Y13, AA16, AA17
IC
Internal Connections
In normal mode these pins MUST be connected low
AB13, AB14
NC
No Connection
In normal mode these pins MUST be left unconnected
Microprocessor Port and Reset
A11, C11, E11, B11, A10,
B10, C10, A9, D10, B9, F11,
A8, C9, B8, E10, A7, A6, D9,
E9, C8, A5, B6, C7, D8, E8,
A4, B5, C6, D7, F8, A3, B4
D0-31
Microprocessor Port Data Bus (5 V Tolerant Bi-directional with
Slew-Rate Output Control)
32 or 16 bit bidirectional data bus. Used for microprocessor access
to internal memories and registers. When 16 bit mode is selected
(D16B is logic 1), D31-16 are unused and must be connected to
defined logic levels.
B16, A17, A16, C14, E13,
D13, B15, A15, B14, C13,
A14, B13, E12, D12, A13,
C12, D11, B12, A12
A0-18
Microprocessor Port Address Bus (5 V Tolerant Inputs)
19 bit address bus for the internal memories and registers. In 16 bit
bus mode (D16B is logic 1), please note A0 is not used and must
be connected to a defined logic level.
In Intel 32 bit mode: A1 = BE3, A0 = BE2
12
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Pin Description (continued)
Pin
Name
Description
C16
CS
Chip Select Input (5 V Tolerant Input)
Active low input used with DS to enable read and write access to
the ZL50073.
D14
DS
Data Strobe Input (5 V Tolerant Input)
Active low input used with CS to enable read and write access to
the ZL50073.
C15
R/W
Read/Write Input (5 V Tolerant Input)
This input controls the direction of the data bus lines (D31 - 0)
during a microprocessor access. This pin is set high and low for the
read and write access respectively.
A19
DTA
Data Transfer Acknowledge (5 V Tolerant, 3.3 V Tri-state
Output with Slew-Rate)
This active low output indicates that a data bus transfer is
complete. Usually used with a Motorola interface. An external
pull-up resistor is required to hold this pin HIGH when output is
high-impedance.
B17
BERR
Transfer Bus Error Output with Slew Rate Control (5 V
Tolerant, 3.3 V Tri-state Outputs with Slew-Rate Control)
This pin goes low whenever the microprocessor attempts to access
an invalid memory space inside the device. In Motorola bus mode,
if this bus error signal is activated, the data transfer acknowledge
signal, DTA, will not be generated. In Intel bus mode, the
generation of the DTA is not affected by this BERR signal. An
external pull-up resistor is required to hold a HIGH level when
output is high-impedance.
D15
WAIT
Data Transfer Wait Output (5 V Tolerant, 3.3 V Tri-state Output
with Slew Rate)
Active low wait signal output. It indicates that a data bus transfer is
complete when it goes from low to high. Usually used with an Intel
interface. An external pull-up resistor is required to hold this pin
HIGH when output is high-impedance
B18, E15
SIZ0-1
Data Transfer Size/Upper and Lower Data Strobe Inputs (5 V
Tolerant Inputs)
Motorola 32-bit mode - signals indicate data transfer size, refer to
Section 10.0.
Motorola 16-bit mode:SIZ0 - LDS, SIZ1 - UDS.
Active low upper and lower data strobes, UDS and LDS, indicate
whether the upper byte, D15 - 8, and/or lower byte, D7 - 0, is being
accessed.
Intel 32/16-bit mode: SIZ0 - BE0, SIZ1 - BE1.
Active low Intel type bus-enable signals, BE1 and BE0
C5
IM
Microprocessor Port Bus Mode Select (5 V Tolerant Input)
Control input:
0 = Motorola mode
1 = Intel mode
13
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Pin Description (continued)
Pin
Name
Description
B7
D16B
Microprocessor Port Bus 16/32 Bit Mode Select (5 V Tolerant
Input with Internal Pull-down)
Control input:
0 = 32 bit data bus
1 = 16 bit data bus
A20
PWR
Device Reset (5 V Tolerant Schmitt-Triggered Input)
Asynchronous reset input used to initialize the ZL50073.
0 = Reset
1 = Normal
See Section 11.0, Power-up and Initialization of the ZL50073 for
detailed description of Reset state.
IEEE 1149.1 Test Access Port (TAP)
D18
TDi
Test Data (5 V Tolerant Input with Internal Pull-up)
Serial test data input. When not used, this input may be left
unconnected.
B21
TDo
Test Data (3.3 V Output)
Serial test data output.
A22
TCK
Test Clock (5 V Tolerant Schmitt-Triggered Input with Internal
Pull-up)
Provides the clock to the JTAG test logic
C19
TRST
Test Reset (5 V Tolerant Schmitt-Triggered Input with Internal
Pull-up)
Asynchronously initializes the JTAG TAP controller by putting it in
the Test-Logic-Reset state. This pin should be pulsed low during
power-up to ensure that the device is in the normal functional
mode. When JTAG is not being used, this pin should be pulled low
during normal operation.
E17
TMS
Test Mode Select (5 V Tolerant Input with Internal Pull-up)
JTAG signal that controls the state transitions of the TAP controller.
When not used, this pin is pulled high by an internal pull-up resistor
and may be left unconnected.
1.0
Functional Description
1.1
Overview
The device has 128 ST-BUS/GCI-Bus inputs (STiA0 - 31, STiB0 - 31, STiC0 - 31, STiD0 - 31) and 128
ST-BUS/GCI-Bus outputs (SToA0 - 31, SToB0 - 31, SToC0 - 31, SToD0 - 31). It is a non-blocking digital switch with
32,768 64 kbps channels and is capable of performing rate conversion between groups of 4 inputs and 4 outputs.
The inputs accept serial input data streams with data rates of 8.192 Mbps, 16.384 Mbps, 32.768 Mbps or
65.536 Mbps. There are 32 input groups with each group consisting of 4 streams (‘A’, ‘B’, ‘C’ and ‘D’). Each group
can be set to any of the data rates. The outputs deliver serial data streams with data rates of 8.192 Mbps,
16.384 Mbps, 32.768 Mbps or 65.536 Mbps. There are 32 output groups with each group consisting of 4 streams
(‘A’, ‘B’, ‘C’ and ‘D’). Each group can be set to any of the data rates.
By using Zarlink’s message mode capability, the microprocessor can store data in the connection memory which
can be broadcast to the output streams on a per-channel basis. This feature is useful for transferring control and
status information for external circuits or other ST-BUS/GCI-Bus devices.
14
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
The ZL50073 uses the ST-BUS/GCI-Bus master input frame pulse (FPi0) and the ST-BUS/GCI-Bus master input
clock (CKi0) to define the input frame boundary and timing for sampling the ST-BUS/GCI-Bus input streams with
various data rates (8.192 Mbps, 16.384 Mbps, 32.768 Mbps or 65.536 Mbps). The rate of the input clock is defined
by setting the CK_SEL1 - 0 pins. In addition, two more frame pulses and clocks can be accepted. The frequencies
of these signals are automatically detected by the ZL50073.
A selectable Motorola or Intel compatible non-multiplexed microprocessor port allows users to program the device
to operate in various modes under different switching configurations. Users can use the microprocessor port to
perform internal register and memory read and write operations. The microprocessor port can be selectable to be
either a 32 bit or 16 bit data bus and to have either a 19 bit or 17 bit address bus. This is selected by setting the
D16B pin. There are seven control signals (CS, DS, R/W, DTA, WAIT, BERR and IM).
The device supports the mandatory requirements for the IEEE 1149.1 (JTAG) standard via the test port.
1.2
Switch Operation
The ZL50073 switches 64 kbps and Nx64 kbps data and voice channels from the TDM input streams, to timeslots
in the TDM output streams. The device is non-blocking; all 32 K input channels can be switched through to the
outputs. Any input channel can be switched to any available output channel.
Input Group 0
STiA0
STiB0
STiC0
STiD0
32K x 32K
SToA0
SToB0
SToC0
SToD0
Output Group 0
TDM INPUT
128 Streams
TDM OUTPUT
128 Streams
SToA31
SToB31
SToC31
SToD31
STiA31
STiB31
Input Group 31
STiC31
STiD31
Output Group 31
ZL50073
Figure 2 - 32 K x 32 K Channel Basic Switch Configuration
The maximum channel switching capacity is determined by the number of streams and their rate of operation, as
shown in Table 1.
TDM Group
Data Rate
Maximum Number
of Input TDM Data
Streams
Maximum Number
of Output TDM
Data Streams
Number of
64 kbps Channels
per Stream
Maximum Switch
Capacity† (streams
x channels = total)
65.536 Mbps
32
32
1024
32 x 1024 = 32,768
32.768 Mbps
64
64
512
64 x 512 = 32,768
16.384 Mbps
128
128
256
128 x 256 = 32,768
8.192 Mbps
128
128
128
128 x 128 = 16,384‡
Table 1 - Data Rate and Maximum Switch Size
† The maximum capacity shown is when all streams are at the same rate, and none are operating at 8.192 Mbps.
‡ Switch capacity is limited to less than 32 K channels, only when streams are provisioned at 8 Mbps. The maximum switch capacity in this case
is given by 32,768 - (N x 128), where N is the number of 8 Mbps input or output streams.
15
Zarlink Semiconductor Inc.
ZL50073
1.3
Data Sheet
Stream Provisioning
The ZL50073 is a large switch with a comprehensive list of user configurable, ’per-group’ programmable features.
In order to facilitate ease of use, the ZL50073 offers a simple programming model. Streams are grouped in sets of
four, with each group sharing the same configured characteristics. In this way it is possible to reduce programming
complexity, while still maintaining flexible ’per-group’ configuration options:
•
Input and output rate selection; see Section 1.4
•
Input stream clock source selection; see Section 2.0
•
Output stream clock source selection; see Section 2.0
•
Input stream sampling point selection; see Section 5.1
•
Output stream fractional bit advance; see Section 5.2
•
Input and output stream inversion control; see Section 14.4
The streams are grouped, one from the TDM ’A’ streams, combined with the corresponding ’B’, ’C’ and ’D’ streams.
For example, input stream group #12 is STiA12, STiB12, STiC12, STiD12, and output stream group #4 is SToA4,
SToB4, SToC4, SToD4. There are 32 input and 32 output groups. Depending on the data rate set for the group
there will be between 1 and 4 streams activated. If the data rate is set for 65.536 Mbps, the ‘A’ stream will be
activated and the ‘B’, ‘C’ and ‘D’ streams will not be activated. If the data rate is set for 32.768 Mbps, the ‘A’ and ‘B’
streams will be activated and the ‘C’ and ‘D’ streams will not be activated. If the data rate is set for either
16.384 Mbps or 8.192 Mbps all of the streams, ‘A’, ‘B’, ‘C’ and ‘D’ will be activated. The maximum channel capacity
of a group is 1024 channels when operating at any data rate except for 8.192 Mbps, in which case the maximum
operating channel capacity decreases to 512 channels.
1.4
Input and Output Rate Selection
Table 1 shows the maximum number of streams available at different bit rates. The ZL50073 deactivates unused
streams when operating at the higher bit rates as shown in Table 2.
Input or Output Group n
(n = 0 - 31)
65 Mbps
32 Mbps
16 Mbps
8 Mbps
STiAn / SToAn
Active
Active
Active
Active
STiBn / SToBn
Not Active
Active
Active
Active
STiCn / SToCn
Not Active
Not Active
Active
Active
STiDn / SToDn
Not Active
Not Active
Active
Active
Table 2 - TDM Stream Bit Rates
For 65 Mbps operation, only those inputs and outputs in the TDM ’A’ streams are active. For 32 Mbps operation,
only those inputs and outputs in the TDM ’A’ and ’B’ streams are active. For 16 Mbps and 8 Mbps, inputs and
outputs in TDM ’A’, ’B’, ’C’ and ’D’ streams are active.
Note that if the internal system clock is not used as the clock source, there are limitations on the maximum data
rate. See Section 2.0 for more details.
1.4.1
Per Group Rate Selection
See Section 14.4, Group Control Registers, for programming details. The data rates are set with the Input Stream
Bit Rate (bits 3 - 2) and the Output Stream Bit Rate (bits 19 - 18) in the Group Control Registers 0 - 31 (GCR0 - 31)
For the ZL50073, the bit rates of the inputs and outputs are programmed independently, in groups of 4 streams.
Depending on the rate programmed, the active streams in the group will be as indicated in Table 2.
16
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
For example:
•
if input stream group #1 is programmed for 65 Mbps: STiA1 is active; STiB1, STiC1, STiD1 are not active
•
if output stream group #15 is programmed for 32 Mbps: SToA15 and SToB15 are active; SToC15 and
SToD15 are not active
•
if input stream group #24 is programmed for 16 Mbps or 8 Mbps, STiA24, STiB24, STiC24, STiD24 are all
active
An example of ZL50073 mixed rate provisioning is given in Figure 3. In this example, the output streams follow the
same data rate as the input streams. The example shows that it is possible to have different groups operating at
different data rates. The first eight groups are operating in 65.536 Mbps mode (8192 channels - 8 streams), the next
eight groups are operating in 32.768 Mbps (8192 channels - 16 streams with 2 streams in each group) and the
remaining sixteen groups are operating in 16.384 Mbps (16384 channels - 64 streams with 4 streams per group).
This results in the full capacity usage of the ZL50073.
Input Groups
0 - 7 at 65 Mbps
STiA0 - 7 at 65 Mbps
STiB0 - 7 Not Active
SToA0 - 7 at 65 Mbps
SToB0 - 7 Not Active
STiC0 - 7 Not Active
SToC0 - 7 Not Active
32 K x 32 K
STiD0 - 7 Not Active
Input Groups
8 - 15 at 32 Mbps
Input Groups
16 - 31 at 16 Mbps
Output Groups
0 - 7 at 65 Mbps
SToD0 - 7 Not Active
STiA8 - 15 at 32 Mbps
STiB8 - 15 at 32 Mbps
SToA8 - 15 at 32 Mbps
SToB8 - 15 at 32 Mbps
STiC8 - 15 Not Active
SToC8 - 15 Not Active
STiD8 - 15 Not Active
SToD8 - 15 Not Active
Output Groups
8 - 15 at 32 Mbps
STiA16 - 31 at 16 Mbps
STiB16 - 31 at 16 Mbps
STiC16 - 31 at 16 Mbps
SToA16 - 31 at 16 Mbps
SToB16 - 31 at 16 Mbps Output Groups
SToC16 - 31 at 16 Mbps 16 - 31 at 16 Mbps
STiD16 - 31 at 16 Mbps
SToD16 - 31 at 16 Mbps
Example:
Input and Output Groups 0 - 7 at 65 Mbps
Input and Output Groups 8 - 15 at 32 Mbps
Input and Output Groups 16 - 31 at 16 Mbps
ZL50073
Figure 3 - ZL50073 32 K x 32 K Channel and Stream Provisioning Example at Multiple Rates
Note: Although this example shows the same rate provisioned for corresponding STi and STo streams, programming of input and
outputs is independent and different settings are possible.
1.5
Rate Conversion
The ZL50073 supports rate conversion from any input stream rate to any output stream rate.
An example of ZL50073 rate conversion is given in Figure 4. Here the total capacity of both the input and the output
is 32,768 channels. The output stream rates do not have to follow the input stream rates. In this example, on the
input side of the switch you have 24 streams operating at 65.536 Mbps (24,576 channels - 24 groups with 1 stream
in each group), 8 streams operating at 32.768 Mbps (4096 channels - 4 groups with 2 streams in each group) and
16 streams operating at 16.384 Mbps (4096 channels - 4 groups with 4 streams in each group) with no streams
operating at 8.192 Mbps. This results in a maximum input capacity of 32,768 input channels. As the output streams
do not have to follow the input streams, they can be configured so that 15 streams operate at 65.536 Mbps (15,360
channels - 15 groups with 1 stream in each group), 28 streams operate at 32.768 Mbps (14,336 channels - 14
groups with 2 streams in each group), 12 streams operate at 16.384 Mbps (3076 channels - 3 groups with 4
streams in each group) and no streams at 8.192 Mbps. This results in a maximum output capacity of 32,768 output
channels. The reason that no stream is operating at 8.192 Mbps is that as soon as one group is set to this data rate,
the capacity of the device will be less than the full 32,768 channels.
17
Zarlink Semiconductor Inc.
ZL50073
Input Groups
0 - 23 at 65 Mbps
Data Sheet
STiA0 - 23 at 65 Mbps
STiB0 - 23 Not Active
SToA0 - 14 at 65 Mbps
SToB0 - 14 Not Active
STiC0 - 23 Not Active
SToC0 - 14 Not Active
STiD0 - 23 Not Active
Output Groups
0 - 14 at 65 Mbps
SToD0 - 14 Not Active
32K x 32K
Input Groups
24 - 27 at 32 Mbps
Input Groups
28 - 31 at 16 Mbps
SToA15 - 28 at 32 Mbps
SToB15 - 28 at 32 Mbps
STiA24 - 27 at 32 Mbps
STiB24 - 27 at 32 Mbps
STiC24 - 27 Not Active
Output Groups
SToC15 - 28 Not Active 15 - 28 at 32 Mbps
STiD24 - 27 Not Active
SToD15 - 28 Not Active
STiA28 - 31 at 16 Mbps
STiB28 - 31 at 16 Mbps
STiC28 - 31 at 16 Mbps
SToA29 - 31 at 16 Mbps
SToB29 - 31 at 16 Mbps
SToC29 - 31 at 16 Mbps
STiD28 - 31 at 16 Mbps
SToD29 - 31 at 16 Mbps
Output Groups
29 - 31 at 16 Mbps
Example:
Input Groups 0 - 23 at 65 Mbps; Output Groups 0 - 14 at 65 Mbps
Input Groups 24 - 27 at 32 Mbps; Output Groups 15 - 28 at 32 Mbps
Input Groups 28 - 31 at 16 Mbps; Output Groups 29 - 31 at 16 Mbps
Figure 4 - Input and Output Data Rate Conversion Example
2.0
Input Clock (CKi) and Input Frame Pulse (FPi) Timing
The input timing for the ZL50073 can be set for one of four different frequencies. They can also be set for ST-BUS
or GCI-Bus mode with positive or negative input. The CKi0 and FPi0 input timing must be provided in order for the
device to be used. There are two additional input clocks and frame pulses that can be provided. CKi0 is used to
generate the internal clock. This clock is used for all the internal logic and can be used as one of the clocks that
defines the timing for the input and output data. The input stream clock source is selected by the ISSRC1 - 0 (bits 1
- 0) in the Group Control Registers. The output stream clock source is selected by the OSSRC1 - 0 (bits 17 - 16) in
the Group Control Registers.
The CKi0 and FPi0 input frequency is set via the CK_SEL1 - 0 pins as shown in Table 3. By default the CKi0 and
FPi0 pins accept ST-BUS, negative input timing. The input frame pulse format (ST-BUS/GCI-Bus), frame pulse
polarity, and clock polarity can be programmed by the GCISEL0 (bit 2), FPIPOL0 (bit 1), and CKIPSL0 (bit 0) in the
Input Clock Control Register (ICCR), as described in Section 14.5.
Input CKi0 and FPi0
CK_SEL1
CK_SEL0
0
0
8.192 MHz
0
1
16.384 MHz
1
0
32.768 MHz
1
1
65.536 MHz
Table 3 - CKi0 and FPi0 Setting via CK_SEL1 - 0
Two additional input clocks (CKi2 - 1) and frame pulses (FPi2 - 1) can be accepted. These signals can be
8.192 MHz, 16.384 MHz, 32.768 MHz or 65.536 MHz and the rates are automatically detected by the device.
These clocks must be phase aligned with the CKi0 within a 30 ns skew but can have different jitter values. The
clocks do not have to have the same frequency. If these additional clocks are not used, the pins must be connected
to a defined logic level.
18
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
These additional input clocks and frame pulses can be used as alternative clock sources for the input streams,
output streams, and output clocks / frame pulses. The input streams’ clock sources are controlled by the ISSRC1-0
(bits 1 - 0) in the Group Control Registers (GCR). The output streams’ clock sources are controlled by the
OSSRC1-0 (bits 17 - 16) in the Group Control Registers (GCR). The output clocks’ / frame pulses’ clock sources
are controlled by the CKO3SRC1-0 (bits 22-21), CKO2SRC1-0 (bits 15-14), CKO1SRC1-0 (bits 8-7), and
CKO0SRC1-0 (bits 1-0) in the Output Clock Control Register (OCCR). The clock sources can be set to either the
internal system clock or one of the three input clock signals. These are used to provide a direct interface to jittery
peripherals.
When the internal system clock is not used as the clock source, there are limitations to the data rate and the output
clock rate. For all the input and output stream groups that do not use the internal system clock as their clock source,
the data rate is limited to be no higher than the selected clock source’s rate (e.g. if CKi1 runs at 16.384 MHz and it
is selected as the clock source for input stream group 3, then the maximum data rate of STiA3, STiB3, STiC3, and
STiD3 is 16.384Mbps). Similarly, for all the output clocks that do not use the internal system clock as their clock
source, the clock rate is limited to be no higher than the selected clock source’s rate (e.g. if CKi1 runs at
32.768 MHz and it is selected as the clock source for output clock CKo0, then the maximum clock rate of CKo0 is
32.768 MHz).
3.0
Output Clock (CKo) and Output Frame Pulse (FPo) Timing
There are four output timing pairs, CKo3 - 0 and FPo3 - 0. By default these signals generate ST-BUS, negative
timing, and use the internal system clock as reference clock source. Their default clock rates are 65.536 MHz for
CKo0, 32.768 MHz for CKo1, 16.384 MHz for CKo2, and 8.192 MHz for CKo3. Their properties can also be
individually programmed in the Output Clock Control Register (OCCR) to control the frame pulse format
(ST-BUS/GCI-Bus), frame pulse polarity, clock polarity, clock rate (8.192 MHz, 16.384 MHz, 32.768 MHz or
65.536 MHz), and reference clock source. Refer to Section 14.6 for programming details. Note that the reference
clock source can be set to either the internal system clock or one of the three input clock signals. If one of the three
input clock signals is selected as the reference source, the output clock cannot be programmed to generate a
higher clock frequency than the reference source. As each output timing pair has its own bit settings, they can be
set to provide different output timings. For 65.536 MHz output clock, the total loading on the output should not
be larger than 10pF.
4.0
Output Channel Control
To be able to interface with external buffers, the output signals can be set to enter a high impedance or drive high
state on a per-channel basis. The Per Channel Function (bits 31 - 29) in the Connection Memory Bits can be set to
001 to drive the channel output high, or to 000, 110 or 111 to set the channel into a high impedance state.
5.0
Data Input Delay and Data Output Advancement
The Group Control Registers (GCR) are used to adjust the input delay and output advancement for each input and
output data groups. Each group is independently programmed.
5.1
Input Sampling Point Delay Programming
The input sampling point delay programming feature provides users with the flexibility of handling different wire
delays when incoming traffic is from different sources.
By default, all input streams have zero delay, such that bit 7 is the first bit that appears after the input frame
boundary (assuming ST-BUS formatting). The nominal input sampling point with zero delay is at the 3/4 bit time.
The input delay is enabled by the Input Sample Point Delay (bit 8 - 4) in the Group Control Registers 0 - 31 (GCR0
- 31) as described in Section 14.4 on page 43. The input sampling point delay can range from 0 to 7 3/4 bit delay
with a 1/4 bit resolution on a per group basis.
19
Zarlink Semiconductor Inc.
ZL50073
Nominal Channel n Boundary
STi[n]
0
7
6
5
Data Sheet
Nominal Channel n+1 Boundary
4
3
2
1
0
00000 (Default)
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
7
6
11111
11110
11101
11100
11011
11010
11001
11000
10111
10110
10101
10100
10011
10010
10001
10000
Example: With a setting of 01111 the sampling point for bit 7 will be 3 1/2 bits
Figure 5 - Input Sampling Point Delay Programming
There are limitations when the ZL50073 is programmed to use CKi2 - 0 as the input stream clock source as
opposed to the internal clock:
•
The granularity of the delay becomes 1/2 the selected reference clock period, or 1/4 bit, whichever is longer
•
If the selected reference clock frequency is the same as the stream bit rate, the granularity of the delay is 1/2 bit.
In this case, the least significant bit of the ISPD register is not used; the remaining 4 bits select the total delay in
1/2 bit increments, to a maximum of 7 1/2 bits. Also, the 0 bit delay reference point changes from the 3/4 bit
position to the 1/2 bit position.
5.2
Fractional Bit Advancement on Output
See Section 14.4, Group Control Registers, for programming details.
This feature is used to advance the output data with respect to the output frame boundary. Each group has its own
bit advancement value which can be programmed in the Group Control Registers 0 - 31 (GCR0 - 31).
By default all output streams have zero bit advancement such that bit 7 is the first bit that appears after the output
frame boundary (assuming ST-BUS formatting). The output advancement is enabled by the Output Stream Bit
Advancement (bits 21 - 20) of the Group Control Registers 0 - 31 (GCR0 - 31), as described in Section 14.4. The
output delay can vary from 0 to 22.8 ns with a 7.6 ns increment. The exception to this is output streams
programmed at 65 Mbps, in which case the increment is 3.8 ns with a total advancement of 11.4 ns.
20
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Nominal 8 MHz
Clock
Nominal 16 MHz
Clock
Nominal 32/65 MHz
Clock
Nominal Output
Bit Timing
OSBA = 00
7.6 ns (~3.8 ns at 65 Mbps)
Level 1
Advance
OSBA = 01
15.2 ns (~7.6 ns at 65 Mbps)
Level 2
Advance
OSBA = 10
22.8 ns (~11.4 ns at 65 Mbps)
Level 3
Advance
OSBA = 11
Figure 6 - Output Bit Advancement Timing
This programming feature is provided to assist in designs where per stream routing delays are significant and
different.
The OSBA bits in the Group Control Registers are used to set the bit-advancement for each of the corresponding
serial output stream groups. Figure 6 illustrates the effect of the OSBA settings on the output timing.
There are limitations when the ZL50073 is programmed to use CKi2 - 0 as the output stream clock source:
•
If the selected reference clock frequency is 65 MHz or 32 MHz, the granularity of the advancement is
reduced to 1/2 the clock period
•
If the selected reference clock frequency is 16 MHz or 8 MHz, bit advancement is not available and the
output streams are driven at the nominal times
6.0
Message Mode
In Message Mode (MSG), microprocessor data can be broadcast to the output data streams on a per-channel
basis. This feature is useful for transferring control and status information to external circuits or other TDM devices.
For a given output channel, when the corresponding Per Channel Function (bits 31 - 29) in the Connection Memory
are set to Message Mode (010), the Connection Memory’s lowest data byte (bits 7 - 0) is output in the timeslot.
Refer to Section 14.1.1, Connection Memory Bit Functions, for programming details.
To increase programming bandwidth, the ZL50073 has separate addressable 32 bit memory locations, called
Connection Memory Least Significant Bytes (LSB), which provide direct access to the Connection Memories’
21
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Lowest data bytes (bits 7 - 0). Up to four consecutive message mode channels can be set with one Connection
Memory LSB access. Refer to Section 14.1.2, Connection Memory LSB, for programming details.
6.1
Data Memory Read
All TDM input channels can be read via the microprocessor port. This feature is useful for receiving control and
status information from external circuits or other TDM devices. Each 32 bit Data Memory access enables up to four
consecutive input channels to be monitored. The Data Memory field is read only; any attempt to write to this
address range will result in a bus error condition signalled back to the host processor. Refer to Section 14.2, Data
Memory, for programming details.
The latency of data reads is up to 3 frames, depending on when the input timeslots are sampled.
6.2
Connection Memory Block Programming
See Section 14.7, Block Init Register, and Section 14.8, Block Init Enable Register, for programming details.
This feature allows for fast initialization of the connection memory after power up. When the block programming
mode is enabled, the contents of Block Init Register are written to all Connection Memory Bits. This operation
completes in one 125 µs frame. During Connection Memory initialization, all TDM output streams are set to high
impedance.
7.0
Data Delay Through the Switching Paths
See Section 14.1.1, Connection Memory Bit Functions, for programming details.
The switching of information from the input serial streams to the output serial streams results in a throughput delay.
The device can be programmed to perform timeslot interchange functions with different throughput delay
capabilities on a per-channel basis. For voice applications, select variable throughput delay to ensure minimum
delay between input and output data. In wideband data application, select constant delay to maintain the frame
integrity of the information through the switch. The delay through the device varies according to the type of
throughput delay selected by programming the Per Channel Function (bits 31 - 29) in the Connection Memories.
When these bits are set to 011, the channel is in variable delay mode. When they are set to 100, the channel is in
constant delay mode.
7.1
Constant Delay Mode
In this mode the frame integrity is maintained in all switching configurations. The delay though the switch is 2
frames - Input Channel + Output Channel. This can result in a minimum delay of 1 frame + 1 channel if the last
channel of a stream is switched to the first channel of a stream. The maximum delay is 1 channel short of 3 frames
delay. This occurs when the first channel of a stream is switched to the last channel of a stream.
The data throughput delay is expressed as a function of ST-BUS/GCI-Bus frames, input channel number (n) and
output channel number (m). The data throughput delay (T) is:
T = 2 frames + (n - m)
22
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3
Figure 7 - Data Throughput Delay for Constant Delay
7.2
Variable Delay Mode
Variable delay mode causes the output channel to be transmitted as soon as possible. This is a useful mode for
voice applications where the minimum throughput delay is more important than data integrity. The delay through the
switch is minimum 3 channels and maximum 1 frame + 2 channels.
N-2 N-1 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9
N-2 N-1 CH0 CH1 CH2 CH3
N-2 N-1 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9
N-2 N-1 CH0 CH1 CH2 CH3
Figure 8 - Data Throughput Delay for Variable Delay
23
Zarlink Semiconductor Inc.
ZL50073
8.0
Data Sheet
Per-Channel A-Law/µ-Law Translation
The ZL50073 provides per channel code translation to be used to adapt pulse code modulation (PCM) voice or data
traffic between networks which use different encoding laws. Code translation is available in both Connection Modes
and Message Mode.
This feature is controlled by the Connection Memories. The V/D (bit 28) defines if the traffic in the channel is voice
or data. The ICL1 - 0 (bits 27 - 26) define the input coding law and the OCL1 - 0 (bits 25 - 24) define the output
coding law. The different coding options are shown in Table 4:
Input Coding
(ICL1- 0)
Output Coding
(OCL1 - 0)
Voice Coding
(V/D bit = 0)
00
00
ITU-T G.711 A-Law
No Code
01
01
ITU-T G.711 µ-Law
Alternate Bit Inversion (ABI)
10
10
A-Law without Alternate Bit
Inversion (ABI)
Inverted Alternate Bit
Inversion (ABI)
11
11
µ-Law without Magnitude
Inversion (MI)
All Bits Inverted
Data Coding
(V/D bit = 1)
Table 4 - Input and Output Voice and Data Coding
For voice coding options, the ITU-T G.711 A-Law and ITU-T G.711 µ-Law are the standard rules for encoding. The
A-Law without Alternate Bit Inversion (ABI) is an alternative code that does not invert the even bits (6, 4, 2, 0). The
µ-Law without Magnitude Inversion (MI) is an alternative code that does not perform Inversion of magnitude bits (6,
5, 4, 3, 2, 1, 0).
When performing data code options, No Code does not invert the bits. The Alternate Bit Inversion (ABI) option
inverts the even bits (6, 4, 2, 0) while the Inverted Alternate Bit Inversion (ABI) inverts the odd bits (7, 5, 3, 1). When
All Bits Inverted is selected, all of the bits (7, 6, 5, 4, 3, 2, 1, 0) are inverted.
The input channel and output channel encoding law are configured independently. If the output channel coding is
set to be different from the input channel, the ZL50073 performs translation between the two standards. If the input
and output encoding laws are set to the same standard, no translation occurs.
9.0
Bit Error Rate Tester
The ZL50073 has one Bit Error Rate (BER) transmitter and one BER receiver for each pair of input and output
streams, resulting in 128 transmitters connected to the output streams and 128 receivers associated with the input
streams. Each transmitter can generate a BER sequence with a pattern of 215-1 Pseudo-Random Code (ITU
O.151). Each transmitter can start at any location on the stream and will last for a minimum of 1 channel to a
maximum of 1 frame time (125 µs). The BER transmitters are enabled by programming the Per Channel Function
(bit 31 - 29) to 101 (PRBS Generator mode) in the Connection Memories.
Multiple Connection Memory locations can be programmed for BER tests. These locations are not required to be
consecutive. However, when read back, the BER locations must be received in the same order that they were
transmitted. If the BER locations are not received in the same order, the BER test will produce errors.
The PRBS bit pattern is sequentially loaded into the output timeslots. An example is shown in Figure 9.
24
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Example segment of serial bit pattern
from Stream N PRBS Generator
..010111001101101111001010110110001011111011010011100001101...
Stream N with Channels
a, b and c enabled
for PRBS insertion
a
b
c
a
Frame m
b
c
Frame m+1
Figure 9 - Example PRBS Timeslot Insertion
Each PRBS detector can be configured to monitor for bit errors in one or more timeslots. The selection of timeslots
is configured by the Input BER Enable Control Memory (IBERECM). See Section 14.3.1 for programming details.
Each detector has an associated 16 bit error counter accessible via the microprocessor interface, as described in
Section 14.3.2, BER Counters. The value of the counter represents the total number of errors detected on the
corresponding input stream. Bit errors are accumulated until the counter is either reset (by writing to the counter or
by resetting the device), or the counter reaches its maximum value, 65,535 (decimal). If more than 65,535 errors
are detected, the counter will hold at the maximum value until reset.
Any number of timeslots may be configured for bit error rate testing; however the user must ensure the following for
correct operation of the BER test function:
1. The number of timeslots enabled for PRBS detection on the input stream must equal the number of timeslots
enabled for PRBS generation on the source output stream.
2. The arrival order of timeslots at the PRBS detector must be the same as the order in which timeslots were transmitted by the PRBS generator. For example, in Figure 9 above, the timeslot order a,b,c must be maintained
through the external path from source TDM output stream to destination TDM input stream.
10.0
Microprocessor Port
The ZL50073 has a generic microprocessor port that provides access to the internal Data Memory (read access
only), Connection Memory, and Control Registers.
The port size can be configured to be either 32 bit or 16 bit, controlled by the D16B pin.
The port works with either Motorola or Intel type microprocessor buses, selected by the IM pin.
10.1
Addressing
The Data Memory, Connection Memory and Control Registers are assigned 32 bit fields in the ZL50073 memory
space. The Address Bus, A18 - 0, controls access to each 32 bit location. Byte addressing is also provided to give
the user programming flexibility, if access to less than 32 bits is required.
Each 32 bit memory or register location spans 4 consecutive addresses. Example:
•
The 32 bit Group Control Register for TDM Group 0 is located at address range 40200 - 40203 Hex
The Least Significant address identifies the Most Significant Byte (MSB) in the 32 bit field, as illustrated in Table 5.
25
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Address (Hex)
Memory/Register Bits
40200
Bits 31:24 (MSB)
40201
Bits 23:16
40202
Bits 15:8
40203
Bits 7:0 (LSB)
Table 5 - Example of Address and Byte Significance
10.2
32 bit Bus Operation
In 32 bit mode (D16B = 0), all 32 bits of the Data Bus, D31 - 0, may be used for write and read transfers. D31 on the
bus maps to Bit 31 of the internal memory or register, D30 maps to Bit 30, etc. The least significant address bits, A1
- 0, and the Data Transfer Size inputs, SIZ0 - 1, identify which bytes are being accessed.
In Motorola Bus mode (IM = 0), A1 - 0 identify the first byte in the 32 bit field to be transferred, as shown in Table 6.
The SIZ0 - 1 inputs indicate the access transfer size, as shown in Table 7.
A1
A0
Byte Addressed
0
0
Bit 31:24
0
1
Bit 23:16
1
0
Bit 15:8
1
1
Bit 7:0
Table 6 - 32 Bit Motorola Mode Byte Addressing
For example, to transfer all 32 bits in a single access: A1 = 0. A0 = 0, SIZ1 = 0, SIZ0 = 0. To transfer D15 - 8 only:
A1 = 1, A0 = 0, SIZ1 = 0, SIZ0 = 1.
SIZ1
SIZ0
Access Transfer Size
0
0
4 Bytes
0
1
1 Byte
1
0
2 Bytes
1
1
3 Bytes
Table 7 - 32 Bit Motorola Mode Access Transfer Size
In Intel Bus Mode (IM = 1), A1 - 0, and SIZ1 - 0 form active low byte enable signals, consistent with BE3 - 0
available on the Intel i960 processor, as shown in Table 8.
Pin
Equivalent
i960 Signal
Byte
Addressed
A1
BE3
Bit 31:24
A0
BE2
Bit 23:16
SIZ1
BE1
Bit 15:8
SIZ0
BE0
Bit 7:0
Table 8 - 32 bit Intel Mode Bus Enable Signals
Byte addressing applies only to write accesses. On read cycles, all 32 bits are output on every access.
26
Zarlink Semiconductor Inc.
ZL50073
10.3
Data Sheet
16 Bit Bus Operation
In 16 bit mode (D16B = 1), D15 - 0 are used for data transfers to/from the ZL50073. D31 - 16 are unused and must
be connected to a defined logic level. D15 on the bus maps to Bit 31 and Bit 15 of the internal 32 bit memory or
register, D14 maps to Bit 30 and Bit 14, etc.
In 16 bit mode, the least significant address bit, A0, is not used, and must be connected to defined logic level. In this
case, address bit A1 and the Data Transfer Size inputs, SIZ1 - 0, identify which bytes are being accessed.
In Motorola Bus Mode (IM = 0), SIZ1 - 0 form active low data strobe signals, consistent with UDS and LDS available
on the MC68000 and MC68302 processors, as shown in Table 9.
In Intel Bus Mode (IM = 1), SIZ1 - 0 form active low byte enable signals, consistent with BE1 and BE0 available on
the Intel i960 processor, as shown in Table 9.
Pin Name
Motorola Mode
MC68000,MC68302
Equivalent Function
IM = 0
Intel Mode i960 Equivalent
Function
IM = 1
Data Bus Bytes Enabled
SIZ1
UDS
BE1
D15-8
SIZ0
LDS
BE0
D7-0
Table 9 - Byte Enable Signals
In both Intel and Motorola modes, the A1 address input is used to identify the word alignment in internal memory.
A1 = 0
Bits 31:16
A1 = 1
Bits 15:0
16-bit word alignments are shown in Table 10. An example of byte addressing is given in Table 11.
Microprocessor
16 bit Data Bus
SIZ1
SIZ0
A1
Internal 32-bit Memory
or Register
D15 - 8
0
1
0
Bits 31:24
0
1
1
Bits 15:8
1
0
0
Bits 23:16
1
0
1
Bits 7:0
0
0
0
Bits 31:16
0
0
1
Bits 15:0
D7 - 0
D15 - 0
1
1
X
1
Table 10 - 16 Bit Mode Word Alignment
1. X - Don’t Care
27
Zarlink Semiconductor Inc.
No access
ZL50073
Address
(Hex)
Register
Description
Data Sheet
Register
Byte
A18 - 0 (binary)
SIZ1
SIZ0
Comments
40200 or
40201
Group Control
Register (Group 0)
Bits 23:16
100 0000 0010 0000 000X†
1
0
8 bit transfer
40282 or
40283
Input Clock Control
Register
Bits 15:8
100 0000 0010 1000 001X†
0
1
8 bit transfer
40286 or
40287
Output Clock
Control Register
Bits 15:0
100 0000 0010 1000 011X†
0
0
16 bit transfer
40284 or
40285
Output Clock
Control Register
Bits 31:16
100 0000 0010 1000 010X†
0
0
16 bit transfer
Table 11 - 16 Bit Mode Example Byte Address
† Don’t Care. A0 is not used.
10.4
10.4.1
Bus Operation
Read Cycle
The operation of a read cycle is illustrated in Figure 10.
•
The microprocessor asserts the R/W control signal high, to signal a read cycle. It also drives the address A,
transfer size, SIZ1 - 0, and chip select logic drives the CS signal active low to select the ZL50073
•
The microprocessor then drives the DS signal active low, to signal the start of the bus cycle. The DS signal
is held low for the duration of the bus cycle
•
WAIT is asserted active low
•
The ZL50073 accesses the requested memory or register location(s), and places the requested data onto
the data bus, D31 - 0 (D15 - 0 in 16 bit Mode). All data bus pins are driven, whether or not they are being
used for the specific data transfer. Unused pins will present unknown data. If the address is to an unused
area of the memory space, unknown data is presented on the data bus
•
The ZL50073 then de-asserts WAIT, and asserts either DTA or BERR, depending on the validity of the data
transfer
•
When the microprocessor observes the active low state of the DTA or the BERR signal, it terminates the bus
cycle by driving the DS pin inactive high
•
When the ZL50073 sees the DS signal go inactive high, it removes the assertions on the DTA or BERR
signals by driving them inactive high
•
When the ZL50073 sees the CS signal go inactive high, it tri-states the data bus, D31 - 0 (D15 - 0 in 16 bit
Mode) and the DTA and BERR signals. However, if CS goes inactive high before DS goes inactive high, the
DTA and BERR signals are driven inactive high before they are tri-stated
•
In Intel mode, DTA is always driven to signal the end of a bus cycle, regardless of BERR
28
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Address A,
SIZ1 - 0
CS
R/W
DS
Data
DTA
BERR
Hi-Z
Hi-Z
WAIT
The cycle termination signals WAIT & DTA are provided for all bus configurations.
Figure 10 - Read Cycle Operation
10.4.2
Write Cycle
The operation of the write cycle is illustrated in Figure 11.
•
The microprocessor asserts the R/W control signal low, to signal a write cycle. It also drives the address A,
data transfer size, SIZ1 - 0, and chip select logic drives the CS signal active low to select the ZL50073
•
The microprocessor then drives the data bus, D31 - 0 (D15 - 0 in 16 bit Mode) with the data to be written,
and then drives the DS signal active low, to signal the start of the bus cycle. The DS signal is held low for the
duration of the bus cycle
•
WAIT is asserted active low
•
The ZL50073 transfers the data presented on the data bus pins into the indicated memory or register
location(s). If the address is to an unused area of the memory space, or to the data memory, no data is
transferred. The microprocessor port cannot write to the Data Memory
•
The ZL50073 then de-asserts WAIT, and asserts either DTA or BERR, depending on the validity of the data
transfer
•
When the microprocessor observes the active low state of the DTA or the BERR signal, it terminates the bus
cycle by driving the DS pin inactive high
•
When the ZL50073 sees the DS signal go inactive high, it removes the assertions on the DTA or BERR
signals by driving them inactive high
•
When the ZL50073 sees the CS signal go inactive high, it tri-states the DTA and BERR signals. However, if
CS goes inactive high before DS goes inactive high, the DTA and BERR signals are driven inactive high
before they are tri-stated
•
In Intel mode, DTA is always driven to signal the end of a bus cycle, regardless of BERR
29
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Address
SIZ1 - 0
CS
R/W
DS
Data
DTA
Hi-Z
BERR
WAIT
The cycle termination signals WAIT & DTA are provided for all bus configurations.
Figure 11 - Write Cycle Operation
11.0
Power-up and Initialization of the ZL50073
11.1
Device Reset and Initialization
The PWR pin is used to reset the ZL50073. When this pin is low, the following functions are performed:
•
Asynchronously puts the microprocessor port in a reset state
•
Tristates all of the output streams (SToA0 - 31, SToB0 - 31, SToC0 - 31 and SToD0 - 31)
•
Preloads all of the registers with their default values (refer to the individual registers for default values)
•
Clears all internal counters
11.2
Power Supply Sequencing
The ZL50073 has two separate power supplies: VDD_IO (3.3 V) and VDD_CORE (1.8 V). The recommended
power-up sequence is for VDD_IO to be applied first, followed by the VDD_CORE supply. VDD_CORE should not lead
VDD_IO supply by more than 0.3 V. Both supplies may be powered-down simultaneously.
11.3
Initialization
Upon power up, the ZL50073 should be initialized as follows:
•
Assert PWR to low immediately after power is applied
•
Set the TRST pin low to disable the JTAG TAP controller
•
Deassert the PWR pin
•
Apply the Master Clock Input (CKi0) and Master Frame Pulse Input (FPi0) to the values defined by the
CK_SEL1 - 0 pins
•
Set the ODE pin low to disable the output streams
30
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Note: After the PWR reset is removed, and on the application of a suitable master clock input, it takes
approximately 1 ms for the internal initialization to complete.
•
Automatic block initialization of the Connection Memory to all zeros occurs, without microprocessor
intervention
•
All Group Control Registers are preset to 000C000C hex, corresponding to rates of 65 Mbps, no link
inversions, no fractional output bit advancements, internal clock source, and no input sample point delays
•
The Input Clock Control Register is preset to 0DB hex, corresponding to:
•
-
All clock inputs set to negative logic sense
-
All frame pulse inputs set to negative logic sense
-
All input frame pulses set to ST-BUS timing
The Output Clock Control Register is pre-set to 060D1C3C hex, corresponding to:
-
All clock outputs set to negative logic sense
-
All frame pulse outputs set to negative logic sense
-
All output frame pulses set to ST-BUS timing
-
All output clock source selections to internal
-
Clock outputs, CKo0 - 3 are preset to rates of 65 MHz, 32 MHz, 16 MHz and 8 MHz, respectively
Note: If the master clock input, CKi0, is not available, the microprocessor port will assert BERR on all accesses and
read cycles.
12.0
IEEE 1149.1 Test Access Port
The JTAG test port is implemented to meet the mandatory requirements of the IEEE 1149.1 (JTAG) standard. The
operation of the boundary-scan circuity is controlled by an external Test Access Port (TAP) Controller.
The ZL50073 uses the public instructions defined in IEEE 1149.1, with the provision of a 16-bit Instruction Register,
and three scannable Test Data Registers: Boundary Scan Register, Bypass Register and Device Identification
Register.
12.1
Test Access Port (TAP)
The Test Access Port (TAP) accesses the ZL50073 test functions. The interface consists of 4 input and 1 output
signal. as follows:
•
Test Clock (TCK) - TCK provides the clock for the test logic. The TCK does not interfere with any on-chip
clock and thus remains independent in the functional mode. The TCK permits shifting of test data into or out
of the Boundary-Scan register cells concurrently with the operation of the device and without interfering with
the on-chip logic.
•
Test Mode Select (TMS) - The TAP Controller uses the logic signals received at the TMS input to control
test operations. The TMS signals are sampled at the rising edge of the TCK pulse. This pin is internally
pulled to VDD_IO when it is not driven from an external source.
•
Test Data Input (TDi) - Serial input data applied to this port is fed either into the instruction register or into a
test data register, depending on the sequence previously applied to the TMS input. Both registers are
described in a subsequent section. The received input data is sampled at the rising edge of TCK pulses.
This pin is internally pulled to VDD_IO when it is not driven from an external source.
•
Test Data Output (TDo) - Depending on the sequence previously applied to the TMS input, the contents of
either the instruction register or data register are serially shifted out towards the TDo. The data out of the
TDo is clocked on the falling edge of the TCK pulses. When no data is shifted through the boundary scan
cells, the TDo driver is set to a high impedance state.
31
Zarlink Semiconductor Inc.
ZL50073
•
Data Sheet
Test Reset (TRST) - Resets the JTAG scan structure. This pin is internally pulled to VDD_IO when it is not
driven from an external source. When JTAG is not in use, this pin must be tied low for normal operation.
The TAP signals are only applied when the ZL50073 is required to be in test mode. When in normal, non-test mode,
TRST must be connected low to disable the test logic. The remaining test pins may be left unconnected.
12.2
Instruction Register
The ZL50073 uses the public instructions defined in the IEEE 1149.1 standard. The JTAG interface contains a
16-bit instruction register. Instructions are serially loaded into the instruction register from the TDi when the TAP
controller is in its shifted-OR state. These instructions are subsequently decoded to achieve two basic functions: to
select the test data register that may operate while the instruction is current and to define the serial test data
register path that is used to shift data between TDi and TDo during register scanning.
12.3
Test Data Register
As specified in the IEEE 1149.1 standard, the ZL50073 JTAG Interface contains three test data registers:
•
The Boundary-Scan Register - The Boundary-Scan register consists of a series of Boundary-Scan cells
arranged to form a scan path around the boundary of the ZL50073 core logic.
•
The Bypass Register - The Bypass register is a single stage shift register that provides a 1-bit path from
TDi to TDo.
•
The Device Identification Register - The JTAG device ID for the ZL50073 is C39914BH
12.4
Version
<31:28>
0000
Part Number
<27:12>
1100 0011 1001 1001
Manufacturer ID
<11:1>
0001 0100 101
LSB
<0>
1
Boundary Scan Description Language (BSDL)
A Boundary Scan Description Language (BSDL) file is available from Zarlink Semiconductor to aid in the use of the
IEEE-1149.1 test interface.
13.0
Memory Map of ZL50073
The memory map for the ZL50073 is given in Table 12.
Address (Hex)
Description
00000 - 1FFFF
Connection Memory
20000 - 27FFF
Connection Memory LSB
28000 - 2FFFF
Data Memory: Read only; Bus error on write (BERR)
30000 - 37FFF
Input BER Enable Control Memory
38000 - 3FFFF
Invalid Address. Access causes Bus error (BERR)
40000 - 401FF
BER Counters
40200 - 4027F
Group Control Registers
40280 - 40283
Input Clock Control Register
40284 - 40287
Output Clock Control Register
Table 12 - Memory Map
32
Zarlink Semiconductor Inc.
ZL50073
Address (Hex)
40288 - 4028B
Data Sheet
Description
Block Init Register
4028C - 4028F
Block Init Enable
40290- 7FFFF
Invalid Address. Access causes Bus error (BERR)
Table 12 - Memory Map (continued)
14.0
Detailed Memory and Register Descriptions
This section describes all the memories and registers that are used in this device.
14.1
Connection Memory
Address range 00000 - 1FFFF hex.
On power-up, all Connection Memory locations are initialized automatically to 00000000 hex, using the Block
Initialization feature, as described in Section 14.7 and Section 14.8.
The 32 bit Connection Memory has 32,768 locations. Each 32 bit long-word is used to program the desired source
data and any other per-channel characteristics of one output time-slot.
The memory map for the Connection Memory is sub-divided into 32 blocks, each corresponding to one of the
possible 32 output stream group numbers. The address ranges for these blocks are illustrated in Table 13.
Output
Group
Start
Address
(Hex)
Address Range
(Hex)
Output
Group
Start
Address
(Hex)
Address Range
(Hex)
0
000000
000000 - 000FFF
16
010000
010000 - 010FFF
1
001000
001000 - 001FFF
17
011000
011000 - 011FFF
2
002000
002000 - 002FFF
18
012000
012000 - 012FFF
3
003000
003000 - 003FFF
19
013000
013000 - 013FFF
4
004000
004000 - 004FFF
20
014000
014000 - 014FFF
5
005000
005000 - 005FFF
21
015000
015000 - 015FFF
6
006000
006000 - 006FFF
22
016000
016000 - 016FFF
7
007000
007000 - 007FFF
23
017000
017000 - 017FFF
8
008000
008000 - 008FFF
24
018000
018000 - 018FFF
9
009000
009000 - 009FFF
25
019000
019000 - 019FFF
10
00A000
00A000 - 00AFFF
26
01A000
01A000 - 01AFFF
11
00B000
00B000 - 00BFFF
27
01B000
01B000 - 01BFFF
12
00C000
00C000 - 00CFFF
28
01C000
01C000 - 01CFFF
13
00D000
00D000 - 00DFFF
29
01D000
01D000 - 01DFFF
14
00E000
00E000 - 00EFFF
30
01E000
01E000 - 01EFFF
15
00F000
00F000 - 00FFFF
31
01F000
01F000 - 01FFFF
Table 13 - Connection Memory Group Address Mapping
33
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
The mapping of each output stream, SToAn, SToBn, SToCn and SToDn, depends on the programmed bit rate. The
address offset range for each stream is illustrated in Table 14.
Output Group Data Rate
Timeslot Range
Output Stream
Stream Address Offset Range (Hex)
65 Mbps
0 - 1023
SToAn
00000 - 00FFF
SToBn, Cn, Dn
N/A
SToAn
00000 - 007FF
SToBn
00800 - 00FFF
SToCn, Dn
N/A
SToAn
00000 - 003FF
SToBn
00400 - 007FF
SToCn
00800 - 00BFF
SToDn
00C00 - 00FFF
SToAn
00000 - 001FF
SToBn
00200 - 003FF
32 Mbps
0 - 511
16 Mbps
0 - 255
8 Mbps
0 - 127
SToCn
00400 - 005FF
SToDn
00600 - 007FF
BERR
00800 - 00FFF
N/A
Table 14 - Connection Memory Stream Address Offset at Various Output Rates
The address range for a particular stream is given by adding the group start address, as indicated in Table 13, to
the appropriate stream offset range, as indicated in Table 14. For example, the Connection Memory address range
for SToB12 operating at 32 Mbps is 00C800-00CFFF; the Connection Memory address range for SToC4 operating
at 8 Mbps is 004400-0045FF.
Each output channel timeslot occupies a range of 4 addresses in the Connection Memories. The timeslot address
offset is illustrated in Table 15. It shows the maximum number of timeslots that a stream can have, but the actual
number of timeslots available depends on the output data rates, as illustrated in Table 1 and Table 14.
Timeslot
SToAn
SToBn
SToCn
SToDn
Address
Offset hex
0
0
0
0
000
1
1
1
1
004
2
2
2
2
008
-
-
-
-
-
126
126
126
126
1F8
127
127
127
127
1FC
128
128
128
128
200
129
129
129
129
204
-
-
-
-
-
254
254
254
254
3F8
255
255
255
255
3FC
Table 15 - Connection Memory Timeslot Address Offset Range
34
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Timeslot
SToAn
SToBn
SToCn
SToDn
Address
Offset hex
256
256
400
257
257
404
-
-
510
510
7F8
511
511
7FC
-
-
-
512
800
513
804
-
-
1021
FF4
1022
FF8
1023
FFC
Table 15 - Connection Memory Timeslot Address Offset Range (continued)
14.1.1
Connection Memory Bit Functions
The bit functions of the connection memory are illustrated in Table 16.
External Read/Write Address: 000000H
Reset Value: 0000H
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
PCF
2
PCF
1
PCF
0
V/D
ICL
1
ICL
0
OCL
1
OCL
0
0
0
0
0
0
0
0
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
GP
4
GP
3
GP
2
GP
1
GP
0
STCH
9
STCH
8
STCH
7
STCH
6
STCH
5
STCH
4
STCH
3
STCH
2
STCH
1
STCH
0
Bit
Name
31 - 29
PCF2 - 0
Description
Per Channel Function
PCF2 - 0
Function
Description
000
OT
Output is tri-stated
001
FH
Output drives high always
010
MSG
Output is in message mode
011
VAR
Variable delay connection mode
100
CD
Constant delay connection mode
101
PRBS
110
OT
Output is tri-stated
111
OT
Output is tri-stated
PRBS Generator
Table 16 - Connection Memory Bits (CMB)
35
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
External Read/Write Address: 000000H
Reset Value: 0000H
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
PCF
2
PCF
1
PCF
0
V/D
ICL
1
ICL
0
OCL
1
OCL
0
0
0
0
0
0
0
0
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
GP
4
GP
3
GP
2
GP
1
GP
0
STCH
9
STCH
8
STCH
7
STCH
6
STCH
5
STCH
4
STCH
3
STCH
2
STCH
1
STCH
0
Bit
Name
28
V/D
27 - 26
ICL1 - 0
Description
Voice/Data Control
When this bit is low, the corresponding channel is for voice.
When this bit is high, the corresponding channel is for data.
Input Coding Law
ICL1 - 0
25 - 24
OCL1 - 0
Input Coding Law
For Voice (V/D bit = 0)
For Data (V/D bit = 1)
00
CCITT.ITU A-Law
No Code
01
CCITT.ITU µ-Law
ABI
10
A-Law w/o ABI
Inverted ABI
11
µ-Law w/o Mag. Inv
All Bits Inverted
Output Coding Law
OCL1 - 0
Output Coding Law
For Voice (V/D bit = 0)
For Data (V/D bit = 1)
00
CCITT.ITU A-Law
No Code
01
CCITT.ITU µ-Law
ABI
10
A-Law w/o ABI
Inverted ABI
11
µ-Law w/o Mag. Inv
All Bits Inverted
23 - 15
Unused
Reserved. In normal functional mode, these bits MUST be set to zero.
14 - 10
GP4 - 0
Source Group Selection. These bits define the input/source group number (31 - 0).
Table 16 - Connection Memory Bits (CMB) (continued)
36
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
External Read/Write Address: 000000H
Reset Value: 0000H
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
PCF
2
PCF
1
PCF
0
V/D
ICL
1
ICL
0
OCL
1
OCL
0
0
0
0
0
0
0
0
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
GP
4
GP
3
GP
2
GP
1
GP
0
STCH
9
STCH
8
STCH
7
STCH
6
STCH
5
STCH
4
STCH
3
STCH
2
STCH
1
STCH
0
Bit
Name
Description
9-0
STCH
9-0
Source Stream and Channel Selection / Message Mode Data
In connection mode (constant/variable delay), these bits define the input/source stream
and channel number, depending on the data rate.
For 65.536 Mbps, bits 9 - 0 select the input channel (0 - 1023).
For 32.768 Mbps, bits 9 - 1 select the input channel (0 - 511). Bit 0 selects stream STiA
(0) or STiB (1).
For 16.869 Mbps, bits 9 - 2 select the input channel (0 - 255). Bits 1 - 0 select stream
STiA (00), STiB (01), STiC (10), or STiD (11).
For 8.192 Mbps, bits 9 - 3 select the input channel (0 - 127). Bit 2 MUST be set to 0. Bits
1 - 0 select stream STiA (00), STiB (01), STiC (10), or STiD (11).
In message mode, bits 7 - 0 define the output data. The data is output sequentially with
bit 7 being output first. Bits 9 - 8 are not used.
Table 16 - Connection Memory Bits (CMB) (continued)
14.1.2
Connection Memory LSB
The Connection Memory Least Significant Byte field is provided to give a convenient alternative way to modify the
output data for a stream in message mode. In this memory address range, all of the connection memory least
significant bytes (bits 7 - 0) are available for read/write in consecutive address locations. This feature is provided for
programming convenience. It can allow higher programming bandwidth on message mode streams. For example,
one longword access to this memory space can read or set the message bytes in four consecutive connection
memory locations. Access to this memory space is big-endian, with the most significant bytes on the data bus
accessing the lower address of the connection memory. For example, for 32-bit data bus, to access the Connection
Memory LSB associated with channels 3 - 0 on a particular stream, the data bus D31 - 24 carry data for channel 0,
D23 - 16 carry data for channel 1, D15 - 8 carry data for channel 2, and D7 - 0 carry data for channel 3. Addressing
into each of the streams is illustrated in Table 17.
Output
Group
Start
Address
(Hex)
Address Range
(Hex)
Output
Group
Start
Address
(Hex)
Address Range
(Hex)
0
020000
020000 - 0203FF
16
024000
024000 - 0243FF
1
020400
020400 - 0207FF
17
024400
024400 - 0247FF
2
020800
020800 - 020BFF
18
024800
024800 - 024BFF
3
020C00
020C00 - 020FFF
19
024C00
024C00 - 024FFF
4
021000
021000 - 0213FF
20
025000
025000 - 0253FF
5
021400
021400 - 0217FF
21
025400
025400 - 0257FF
Table 17 - Connection Memory LSB Group Address Mapping
37
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Output
Group
Start
Address
(Hex)
Address Range
(Hex)
Output
Group
Start
Address
(Hex)
Address Range
(Hex)
6
021800
021800 - 021BFF
22
025800
025800 - 025BFF
7
021C00
021C00 - 021FFF
23
025C00
025C00 - 025FFF
8
022000
022000 - 0223FF
24
026000
026000 - 0263FF
9
022400
022400 - 0227FF
25
026400
026400 - 0267FF
10
022800
022800 - 022BFF
26
026800
026800 - 026BFF
11
022C00
022C00 - 022FFF
27
026C00
026C00 - 026FFF
12
023000
023000 - 0233FF
28
027000
027000 - 0273FF
13
023400
023400 - 0237FF
29
027400
027400 - 0277FF
14
023800
023800 - 023BFF
30
027800
027800 - 027BFF
15
023C00
023C00 - 023FFF
31
027C00
027C00 - 027FFF
Table 17 - Connection Memory LSB Group Address Mapping (continued)
38
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Output Group Data Rate
Timeslot Range
Output Stream
Stream Address Offset Range (Hex)
65 Mbps
0 - 1023
SToAn
00000 - 003FF
32 Mbps
0 - 511
16 Mbps
8 Mbps
SToBn, Cn, Dn
N/A
SToAn
00000 - 001FF
SToBn
00200 - 003FF
SToCn, Dn
N/A
SToAn
00000 - 000FF
SToBn
00100 - 001FF
SToCn
00200 - 002FF
SToDn
00300 - 003FF
SToAn
00000 - 0007F
SToBn
00080 - 000FF
SToCn
00100 - 0017F
SToDn
00180 - 001FF
BERR
00200 - 003FF
0 - 255
0 - 127
N/A
Table 18 - Connection Memory LSB Stream Address Offset at Various Output Rates
Within each stream group, the mapping of each of the actual output streams, SToAn, SToBn, SToCn and SToDn,
depends on the output rate programmed into the Group Control Registers. The address offsets to these control
areas for each of the output streams are illustrated in Table 18.
39
Zarlink Semiconductor Inc.
ZL50073
14.2
Data Sheet
Data Memory
The data memory field is a read only address range used to monitor the data being received by the input streams.
Addressing into each of the streams is illustrated in Table 19.
Input
Group
Start
Address
(Hex)
Address Range
(Hex)
Input
Group
Start
Address
(Hex)
Address Range
(Hex)
0
028000
028000 - 0283FF
16
02C000
02C000 - 02C3FF
1
028400
028400 - 0287FF
17
02C400
02C400 - 02C7FF
2
028800
028800 - 028BFF
18
02C800
02C800 - 02CBFF
3
028C00
028C00 - 028FFF
19
02CC00
02CC00 - 02CFFF
4
029000
029000 - 0293FF
20
02D000
02D000 - 02D3FF
5
029400
029400 - 0297FF
21
02D400
02D400 - 02D7FF
6
029800
029800 - 029BFF
22
02D800
02D800 - 02DBFF
7
029C00
029C00 - 029FFF
23
02DC00
02DC00 - 02DFFF
8
02A000
02A000 - 02A3FF
24
02E000
02E000 - 02E3FF
9
02A400
02A400 - 02A7FF
25
02E400
02E400 - 02E7FF
10
02A800
02A800 - 02ABFF
26
02E800
02E800 - 02EBFF
11
02AC00
02AC00 - 02AFFF
27
02EC00
02EC00 - 02EFFF
12
02B000
02B000 - 02B3FF
28
02F000
02F000 - 02F3FF
13
02B400
02B400 - 02B7FF
29
02F400
02F400 - 02F7FF
14
02B800
02B800 - 02BBFF
30
02F800
02F800 - 02FBFF
15
02BC00
02BC00 - 02BFFF
31
02FC00
02FC00 - 02FFFF
Table 19 - Data Memory Group Address Mapping
Within each stream group, the mapping of each of the actual input streams, STiAn, STiBn, STiCn and STiDn,
depends on the input rate programmed into the Group Control Registers. The address offsets to these data areas
for each of the input streams are illustrated in Table 20.
Input Group Data Rate
Time-slot Range
65 Mbps
0 - 1023
32 Mbps
16 Mbps
0 - 511
0 - 255
Input Streams
Address Offset Range (Hex)
STiAn
00000 - 003FF
STiBn, Cn, Dn
N/A
STiAn
00000 - 001FF
STiBn
00200 - 003FF
STiCn, Dn
N/A
STiAn
00000 - 000FF
STiBn
00100 - 001FF
STiCn
00200 - 002FF
STiDn
00300 - 003FF
Table 20 - Data Memory Stream Address Offset at Various Output Rates
40
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Input Group Data Rate
Time-slot Range
Input Streams
Address Offset Range (Hex)
8 Mbps
0 - 127
STiAn
00000 - 0007F
N/A
STiBn
00080 - 000FF
STiCn
00100 - 0017F
STiDn
00180 - 001FF
BERR
00200 - 003FF
Table 20 - Data Memory Stream Address Offset at Various Output Rates (continued)
The address ranges for the data memory portion corresponding to each of the actual input streams, STiAn, STiBn,
STiCn and STiDn, for any particular input group number is calculated by adding the Start Address for the particular
group, as indicated in Table 19, to the appropriate Address Offset Range, as indicated in Table 20. The time-slots
map linearly into the appropriate address offset range. (i.e. timeslots 0, 1, 2, ... map into addresses 00000, 00001,
00002, ...)
The entire data memory is a read only structure. Any write attempts will result in a bus error. BERR is driven active
low to terminate the bus cycle.
14.3
14.3.1
BER Control Memory and Error Counters
Input BER Enable Control Memory
The BER Enable Control Memory (IBERECM) is a read/write memory block. Each memory location is used to
control the BER counter of one incoming timeslot. Addressing into each of the streams is illustrated in Table 21.
Input
Group
Start
Address
(Hex)
Address Range
(Hex)
Input
Group
Start
Address
(Hex)
Address Range
(Hex)
0
030000
030000 - 0303FF
16
034000
034000 - 0343FF
1
030400
030400 - 0307FF
17
034400
034400 - 0347FF
2
030800
030800 - 030BFF
18
034800
034800 - 034BFF
3
030C00
030C00 - 030FFF
19
034C00
034C00 - 034FFF
4
031000
031000 - 0313FF
20
035000
035000 - 0353FF
5
031400
031400 - 0317FF
21
035400
035400 - 0357FF
6
031800
031800 - 031BFF
22
035800
035800 - 035BFF
7
031C00
031C00 - 031FFF
23
035C00
035C00 - 035FFF
8
032000
032000 - 0323FF
24
036000
036000 - 0363FF
9
032400
032400 - 0327FF
25
036400
036400 - 0367FF
10
032800
032800 - 032BFF
26
036800
036800 - 036BFF
11
032C00
032C00 - 032FFF
27
036C00
036C00 - 036FFF
12
033000
033000 - 0333FF
28
037000
037000 - 0373FF
13
033400
033400 - 0337FF
29
037400
037400 - 0377FF
14
033800
033800 - 033BFF
30
037800
037800 - 037BFF
15
033C00
033C00 - 033FFF
31
037C00
037C00 - 037FFF
Table 21 - BER Enable Control Memory Group Address Mapping
41
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
Each byte location of the BER Enable Memory contains one read/write BER counter enable (BCE) bit, mapped into
the D0 location. If the BCE bit is set, then the BER counter for the corresponding stream and timeslot is enabled for
the duration of that timeslot. If the BCE bit is cleared the counter is disabled.
Input Group Data Rate
Time-slot Range
Input Streams
Address Offset Range (Hex)
65 Mbps
0 - 1023
STiAn
00000 - 003FF
STiBn, Cn, Dn
N/A
STiAn
00000 - 001FF
STiBn
00200 - 003FF
STiCn, Dn
N/A
32 Mbps
0 - 511
16 Mbps
0 - 255
8 Mbps
0 - 127
N/A
STiAn
00000 - 000FF
STiBn
00100 - 001FF
STiCn
00200 - 002FF
STiDn
00300 - 003FF
STiAn
00000 - 0007F
STiBn
00080 - 000FF
STiCn
00100 - 0017F
STiDn
00180 - 001FF
BERR
00200 - 003FF
Table 22 - BER Enable Control Memory Stream Address Offset at Various Output Rates
14.3.2
BER Counters
There are a total of 128 Bit Error Counters, corresponding to the 128 serial input streams. Each count value is 32
bits wide, but only the least significant 16 bits are used. The most significant 16 bits of the bit error counters will
always read back zero. A write operation to any byte of the counter, including the 16 most significant bits, will clear
that counter.
Each bit error counter contains the number of single bit errors detected on the corresponding stream, since the
counter was last cleared. If the number of bit errors detected exceeds 65535 (decimal), the counter will hold that
value until it is cleared.
BER Input Group
BER Input Stream
Start Address (Hex)
Address Range (Hex)
0
STiA0
040000
040000 - 040003
STiB0
040004
040004 - 040007
STiC0
040008
040008 - 04000B
STiD0
04000C
04000C - 04000F
STiA1
040010
040010 - 040013
STiB1
040014
040014 - 040017
STiC1
040018
040018 - 04001B
STiD1
04001C
04001C - 04001F
.
.
.
.
.
.
1
.
.
Table 23 - BER Counter Group and Stream Address Mapping
42
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
BER Input Group
BER Input Stream
Start Address (Hex)
Address Range (Hex)
31
STiA31
0401F0
0401F0 - 0401F3
STiB31
0401F4
0401F4 - 0401F7
STiC31
0401F8
0401F8 - 0401FB
STiD31
0401FC
0401FC - 0401FF
Table 23 - BER Counter Group and Stream Address Mapping (continued)
14.4
Group Control Registers
The ZL50073 addresses the issues of a simple programming model and automatic stream configuration by defining
a basic switching bit rate of 65.536 Mbps and by grouping the I/O streams. Each TDM I/O group contains 4 input
and 4 output streams. The 4 input streams in the same group have identical input characteristics, and similarly, the
4 output streams in the same group have identical output characteristics. However, input and output streams in the
same group can have different input and output operation characteristics.
The Group Control Registers are provided for setting the operating characteristics of the TDM input and output
streams. All of the Group Control Registers are mapped long-word aligned on 32 bit boundaries in the memory
space. Each of the 32 registers is used to control one group. The mapping of the Group Control Registers to the I/O
group numbers is illustrated in Table 24. The bit functions of each of the Group Control Registers are illustrated in
Table 25.
TDM Group
Group Control Register Address (Hex)
0
40200 - 40203
1
40204 - 40207
2
40208 - 4020B
3
4020C - 4020F
:
:
:
:
29
40274 - 40277
30
40278 - 4027B
31
4027C - 4027F
Table 24 - Group Control Register Addressing
43
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
External Read/Write Address: 40200H - 4027FH
Reset Value: 000C000CH
31
30
29
28
27
26
25
24
23
22
21
20
19
17
16
0
0
0
0
0
0
0
0
0
OSI
OSBR 0
OSSRC 1
OSSRC 0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
ISI
ISPD
4
ISPD
3
ISPD
2
ISPD
1
ISPD
0
ISBR
1
ISBR
0
ISSRC
1
ISSRC
0
Bit
Name
31 - 23
Unused
22
OSI
21 - 20
OSBA1 - 0
19 - 18
OSBR1 - 0
OSBA 1 OSBA 0 OSBR 1
18
Description
Reserved. In normal functional mode, these bits MUST be set to zero.
Output Stream Invert
For normal operation, this bit is set low.
To invert the output stream, set this bit high.
Output Stream Bit Advancement
OSBA1 - 0
Non-65 Mbps
65 Mbps
00
0 ns
0 ns
01
7.6 ns
3.8 ns
10
15.2 ns
7.6 ns
11
22.8 ns
11.4 ns
Output Stream Bit Rate
OSBR1 - 0
Bit Rates Per Group
STi/oA
STi/oB
STi/oC
STi/oD
00
8.192 Mbps
8.192 Mbps
8.192 Mbps
8.192 Mbps
01
16.384 Mbps
16.384 Mbps
16.384 Mbps
16.384 Mbps
10
32.768 Mbps
32.768 Mbps
Not Used
Not Used
11
65.536 Mbps
Not Used
Not Used
Not Used
Unused streams are tri-stated.
If the internal system clock is used as the clock source, all the above data rates are
available. Otherwise, the data rate cannot exceed the selected clock source’s rate.
17 - 16
OSSRC1 - 0
Output Stream Clock Source Select
OSSRC1 - 0
Output Timing Source
00
Internal System Clock
01
CKi0 and FPi0
10
CKi1 and FPi1
11
CKi2 and FPi2
Table 25 - Group Control Register
44
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
External Read/Write Address: 40200H - 4027FH
Reset Value: 000C000CH
31
30
29
28
27
26
25
24
23
22
21
20
19
OSBA 1 OSBA 0 OSBR 1
18
17
16
0
0
0
0
0
0
0
0
0
OSI
OSBR 0
OSSRC 1
OSSRC 0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
ISI
ISPD
4
ISPD
3
ISPD
2
ISPD
1
ISPD
0
ISBR
1
ISBR
0
ISSRC
1
ISSRC
0
Bit
Name
Description
15 - 10
Unused
9
ISI
8-4
ISPD4 - 0
Input Sampling Point Delay
Default Sampling Point is 3/4. Adjust according to Figure 5 on page 20.
3-2
ISBR1 - 0
Input Stream Bit Rate
Reserved. In normal functional mode, these bits MUST be set to zero.
Input Stream Inversion
For normal operation, this bit is set low.
To invert the input stream, set this bit high.
ISBR1 - 0
Bit Rates Per Group
STi/oA
STi/oB
STi/oC
STi/oD
00
8.192 Mbps
8.192 Mbps
8.192 Mbps
8.192 Mbps
01
16.384 Mbps
16.384 Mbps
16.384 Mbps
16.384 Mbps
10
32.768 Mbps
32.768 Mbps
Not Used
Not Used
11
65.536 Mbps
Not Used
Not Used
Not Used
Unused streams must be connected to ground.
If the internal system clock is used as the clock source, all the above data rates are
available. Otherwise, the data rate cannot exceed the selected clock source’s rate.
1-0
ISSRC1 - 0
Input Stream Clock Source Select
ISSRC1 - 0
Input Timing Source
00
Internal System Clock
01
CKi0 and FPi0
10
CKi1 and FPi1
11
CKi2 and FPi2
Table 25 - Group Control Register (continued)
The Group Control Register is a static control register. Changes to bit settings may disrupt data flow on the selected
port for a maximum of 2 frames.
45
Zarlink Semiconductor Inc.
ZL50073
14.5
Data Sheet
Input Clock Control Register
The Input Clock Control Register is used to select the logic sense of the input clock.
External Read/Write Address: 40280H
Reset Value: 0DBH
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
GCI
SEL2
FPI
POL2
CKI
POL2
GCI
SEL1
FPI
POL1
CKI
POL1
GCI
SEL0
FPI
POL0
CKI
POL0
Bit
Name
Description
31 - 9
Unused
8
GCISEL2
GCI-Bus Selection for FPi2
When this bit is low, FPi2 is set for ST-BUS mode.
When this bit is high, FPi2 is set for GCI-Bus mode.
7
FPIPOL2
Frame Pulse Polarity Selection for FPi2
When this bit is low, FPi2 is set for active high.
When this bit is high, FPi2 is set for active low.
6
CKIPOL2
Clock Polarity Selection for CKi2
When this bit is low, CKi2 is set for the positive clock edge.
When this bit is high, CKi2 is set for negative.
5
GCISEL1
GCI-Bus Selection for FPi1
When this bit is low, FPi1 is set for ST-BUS mode.
When this bit is high, FPi1 is set for GCI-Bus mode.
4
FPIPOL1
Frame Pulse Polarity Selection for FPi1
When this bit is low, FPi1 is set for active high.
When this bit is high, FPi1 is set for active low.
3
CKIPOL1
Clock Polarity Selection for CKi1
When this bit is low, CKi1 is set for the positive clock edge.
When this bit is high, CKi1 is set for negative.
2
GCISEL0
GCI-Bus Selection for FPi0
When this bit is low, FPi0 is set for ST-BUS mode.
When this bit is high, FPi0 is set for GCI-Bus mode.
1
FPIPOL0
Frame Pulse Polarity Selection for FPi0
When this bit is low, FPi0 is set for active high.
When this bit is high, FPi0 is set for active low.
0
CKIPOL0
Clock Polarity Selection for CKi0
When this bit is low, CKi0 is set for the positive clock edge.
When this bit is high, CKi0 is set for negative.
Reserved. In normal functional mode, these bits MUST be set to zero.
Table 26 - Input Clock Control Register
46
Zarlink Semiconductor Inc.
ZL50073
14.6
Data Sheet
Output Clock Control Register
The Output Clock Control Register is used to select the desired source, frequency, and logic sense of the output
clocks. The bit functions of the Output Clock Control Register are illustrated in Table 27.
External Read/Write Address: 40284H
Reset Value: 060D1C3CH
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
0
0
0
GCO
SEL3
FPO
POL3
CKO
POL3
CKO3
RATE1
CKO3
RATE0
CKO3
SRC1
CKO3
SRC0
GCO
SEL2
FPO
POL2
CKO
POL2
CKO2
RATE1
CKO2
RATE0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CKO2
SRC1
CKO2
SRC0
GCO
SEL1
FPO
POL1
CKO
POL1
CKO1
RATE1
CKO1
RATE0
CKO1
SRC1
CKO1
SRC0
GCO
SEL0
FPO
POL0
CKO
POL0
CKO0
RATE1
CKO0
RATE0
CKO0
SRC1
CKO0
SRC0
Bit
Name
Description
31 - 28
Unused
27
GCO
SEL3
GCI-Bus Selection for FPo3
When this bit is low, FPo3 is set for ST-BUS mode.
When this bit is high, FPo3 is set for GCI-Bus mode.
26
FPO
POL3
Frame Pulse Polarity Selection for FPo3
When this bit is low, FPo3 is set for active high.
When this bit is high, FPo3 is set for active low.
25
CKO
POL3
Clock Polarity Selection for CKo3
When this bit is low, CKo3 is set for the positive clock edge.
When this bit is high, CKo3 is set for the negative clock edge.
24 - 23
CKO3
RATE
1-0
Output Clock Rate for CKo3 and FPo3
The output clock rate can not exceed the selected clock source rate. All rates are available when the internal system clock is selected as clock source.
Reserved. In normal functional mode, these bits MUST be set to zero.
CKO3RATE1 - 0
22 - 21
CKO3
SRC
1-0
CKo3
FPo3
00
8.192 MHz
120 ns
01
16.384 MHz
60 ns
10
32.768 MHz
30 ns
11
65.536 MHz
15 ns
Output Clock Source for CKo3 and FPo3
CKO3SRC1 - 0
Output Timing Source
00
Internal System Clock
01
CKi0 and FPi0
10
CKi1 and FPi1
11
CKi2 and FPi2
Table 27 - Output Clock Control Register
47
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
External Read/Write Address: 40284H
Reset Value: 060D1C3CH
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
0
0
0
GCO
SEL3
FPO
POL3
CKO
POL3
CKO3
RATE1
CKO3
RATE0
CKO3
SRC1
CKO3
SRC0
GCO
SEL2
FPO
POL2
CKO
POL2
CKO2
RATE1
CKO2
RATE0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CKO2
SRC1
CKO2
SRC0
GCO
SEL1
FPO
POL1
CKO
POL1
CKO1
RATE1
CKO1
RATE0
CKO1
SRC1
CKO1
SRC0
GCO
SEL0
FPO
POL0
CKO
POL0
CKO0
RATE1
CKO0
RATE0
CKO0
SRC1
CKO0
SRC0
Bit
Name
20
GCO
SEL2
GCI-Bus Selection for FPo2
When this bit is low, FPo2 is set for ST-BUS mode.
When this bit is high, FPo2 is set for GCI-Bus mode.
19
FPO
POL2
Frame Pulse Polarity Selection for FPo2
When this bit is low, FPo2 is set for active high.
When this bit is high, FPo2 is set for active low.
18
CKO
POL2
Clock Polarity Selection for CKo2
When this bit is low, CKo2 is set for the positive clock edge.
When this bit is high, CKo2 is set for the negative clock edge.
17 - 16
CKO2
RATE
1-0
Output Clock Rate for CKo2 and FPo2
The output clock rate can not exceed the selected clock source rate. All rates are available when the internal system clock is selected as clock source.
15 - 14
13
CKO2
SRC
1-0
GCO
SEL1
Description
CKO2RATE1 - 0
CKo2
FPo2
00
8.192 MHz
120 ns
01
16.384 MHz
60 ns
10
32.768 MHz
30 ns
11
65.536 MHz
15 ns
Output Clock Source for CKo2 and FPo2
CKO2SRC1 - 0
Output Timing Source
00
Internal System Clock
01
CKi0 and FPi0
10
CKi1 and FPi1
11
CKi2 and FPi2
GCI-Bus Selection for FPo1
When this bit is low, FPo1 is set for ST-BUS mode.
When this bit is high, FPo1 is set for GCI-Bus mode.
Table 27 - Output Clock Control Register (continued)
48
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
External Read/Write Address: 40284H
Reset Value: 060D1C3CH
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
0
0
0
GCO
SEL3
FPO
POL3
CKO
POL3
CKO3
RATE1
CKO3
RATE0
CKO3
SRC1
CKO3
SRC0
GCO
SEL2
FPO
POL2
CKO
POL2
CKO2
RATE1
CKO2
RATE0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CKO2
SRC1
CKO2
SRC0
GCO
SEL1
FPO
POL1
CKO
POL1
CKO1
RATE1
CKO1
RATE0
CKO1
SRC1
CKO1
SRC0
GCO
SEL0
FPO
POL0
CKO
POL0
CKO0
RATE1
CKO0
RATE0
CKO0
SRC1
CKO0
SRC0
Bit
Name
12
FPO
POL1
Frame Pulse Polarity Selection for FPo1
When this bit is low, FPo1 is set for active high.
When this bit is high, FPo1 is set for active low.
11
CKO
POL1
Clock Polarity Selection for CKo1
When this bit is low, CKo1 is set for the positive clock edge.
When this bit is high, CKo1 is set for the negative clock edge.
10 - 9
CKO1
RATE
1-0
Output Clock Rate for CKo1 and FPo1
The output clock rate can not exceed the selected clock source rate. All rates are available when the internal system clock is selected as clock source.
8-7
CKO1
SRC
1-0
Description
CKO1RATE1 - 0
CKo1
FPo1
00
8.192 MHz
120 ns
01
16.384 MHz
60 ns
10
32.768 MHz
30 ns
11
65.536 MHz
15 ns
Output Clock Source for CKo1 and FPo1
CKO1SRC1 - 0
Output Timing Source
00
Internal System Clock
01
CKi0 and FPi0
10
CKi1 and FPi1
11
CKi2 and FPi2
6
GCO
SEL0
GCI-Bus Selection for FPo0
When this bit is low, FPo0 is set for ST-BUS mode.
When this bit is high, FPo0 is set for GCI-Bus mode.
5
FPO
POL0
Frame Pulse Polarity Selection for FPo0
When this bit is low, FPo0 is set for active high.
When this bit is high, FPo0 is set for active low.
Table 27 - Output Clock Control Register (continued)
49
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
External Read/Write Address: 40284H
Reset Value: 060D1C3CH
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
0
0
0
0
GCO
SEL3
FPO
POL3
CKO
POL3
CKO3
RATE1
CKO3
RATE0
CKO3
SRC1
CKO3
SRC0
GCO
SEL2
FPO
POL2
CKO
POL2
CKO2
RATE1
CKO2
RATE0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
CKO2
SRC1
CKO2
SRC0
GCO
SEL1
FPO
POL1
CKO
POL1
CKO1
RATE1
CKO1
RATE0
CKO1
SRC1
CKO1
SRC0
GCO
SEL0
FPO
POL0
CKO
POL0
CKO0
RATE1
CKO0
RATE0
CKO0
SRC1
CKO0
SRC0
Bit
Name
Description
4
CKO
POL0
Clock Polarity Selection for CKo0
When this bit is low, CKo0 is set for the positive clock edge.
When this bit is high, CKo0 is set for the negative clock edge.
3-2
CKO0
RATE
1-0
Output Clock Rate for CKo0 and FPo0
The output clock rate can not exceed the selected clock source rate. All rates are available when the internal system clock is selected as clock source.
CKO0RATE1 - 0
1-0
CKO0
SRC
1-0
CKo0
FPo0
00
8.192 MHz
120 ns
01
16.384 MHz
60 ns
10
32.768 MHz
30 ns
11
65.536 MHz
15 ns
Output Clock Source for CKo0 and FPo0
CKO0SRC1 - 0
Output Timing Source
00
Internal System Clock
01
CKi0 and FPi0
10
CKi1 and FPi1
11
CKi2 and FPi2
Table 27 - Output Clock Control Register (continued)
50
Zarlink Semiconductor Inc.
ZL50073
14.7
Data Sheet
Block Init Register
The Block Init Register is a 32 bit read/write register at address 040288 - 04028BH.
The Block Init Register is used during block initialization of the connection memory. A block initialization
automatically occurs at power-up. However, it is possible to perform a block initialization at any time. During Block
Initialization, the value of the Block Init Register is copied to all connection memory locations in an operation that
runs in about 120 µs. If the Block Init Register is modified during a block initialization, the new value used is
ignored.
14.8
Block Init Enable Register
The Block Init Enable Register is a 32 bit read/write register at address 04028C - 04028FH.
The Block Init Enable Register is used to initiate a block initialization of the connection memory. A block initialization
automatically occurs at power-up. Since the Block Init Register is cleared at power-up this automatic block
initialization will write all zeros to all Connection Memory Bits. However, it is possible to perform a block initialization
at any time. To begin a block initialization, the hex value 31415926 must be written to the Block Init Enable Register.
If a block initialization is signaled while one is in progress, the signal is ignored, and the currently active block
initialization is allowed to complete.
The value read back from the Block Init Enable Register is different from the value written. It represents both the
block initialization status, and the power-up reset initialization status. The meaning of the initialization status bits is
illustrated in Table 28. The bits 31 - 2 always read back 0.
Bit
Name
Description
0
Block Init Status
0 if Block initialization is completed;
1 if Block initialization is in progress
1
Reset Init Status
0 if Reset initialization is completed
1 if Reset initialization is in progress
Table 28 - Block and Power-up Initialization Status Bits
Any access to the connection memory or the data memory during a block initialization or a reset initialization will
result in a bus error, BERR. All TDM outputs are tri-stated during any block initialization.
51
Zarlink Semiconductor Inc.
ZL50073
15.0
Data Sheet
DC/AC Electrical Characteristics
Absolute Maximum Ratings1 - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Sym.
Min.
VDD_IO
Typ.2
Max.
Unit
-0.5
5.0
V
VDD_CORE
-0.5
5.0
V
1
Chip I/O Supply Voltage
2
Chip Core Supply Voltage
3
Input Voltage (non-5 V tolerant inputs)
VI_3V
-0.5
VDD_IO +
0.5
V
4
Input Voltage (5 V tolerant inputs)
VI_5V
-0.5
7.0
V
5
Continuous Current at digital outputs
Io
15
mA
6
Package power dissipation
PD
2.1
W
7
Storage temperature
TS
+125
°C
Note 1:
Note 2:
- 55
Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Sym.
Min.
Typ.1
Max.
Unit
TOP
-40
25
+85
°C
VDD_CORE
1.71
1.8
1.89
V
VDD_IO
3.0
3.3
3.6
V
V
1
Operating Temperature
2
Positive Supply Core
3
Positive Supply I/O
4
Input Voltage (non-5 V tolerant inputs)
VI_3V
0
VDD_IO
5
Input Voltage (5 V tolerant inputs)
VI_5V
0
5.5
Note 1:
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
DC Electrical Characteristics - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Sym.
Min.
Typ.1
Max.
Unit
IDD_CORE
500
mA
IDD_IO
62
mA
Test Conditions
1
Core Supply Current2
2
I/O Supply Current
3
Leakage Current
IDDQ
4
Dynamic Power Dissipation
PDD
5
Input High Voltage
VIH
6
Input Low Voltage
VIL
0.8
V
7
Input Leakage-input pins3
IIL
5
µA
0≤<VI ≤VDD_IO
8
Input Leakage-bidirectional pins
IBL
5
µA
0≤<VI ≤VDD_IO
9
Pull-up Current
IPU
µA
Input at 0 V
Outputs Unloaded
µA
105
1.2
2.0
W
Outputs Unloaded
V
-33
52
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
DC Electrical Characteristics - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics
Sym.
Min.
Typ.1
Max.
Unit
10
Pull-down Current
IPD
33
µA
11
Input Pin Capacitance
CI
3
pF
12
Output High Voltage
13
Output Low Voltage
VOH
2.4
V
Test Conditions
Input at VDD_IO
IOH = 8 mA
Note 1:
0.4
V
IOL = 8 mA
VOL
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
Note 2:
Note 3:
StoA = 65 Mbps with random patterns. CKo0 = 65 MHz, CKo1 = 32 MHz.
Maximum leakage on pins (output or I/O pins in high impedance state) is over an applied voltage (Vin).
AC Electrical Characteristics1 - Timing Parameter Measurement Voltage Levels - Voltages are with respect to ground
(VSS) unless otherwise stated.
Characteristics
Sym.
Level
Unit
1
CMOS Threshold
VCT
0.5 VDD_IO
V
2
Rise/Fall Threshold Voltage High
VHM
0.7 VDD_IO
V
3
Rise/Fall Threshold Voltage Low
VLM
0.3 VDD_IO
V
Test Conditions
1. Characteristics are over recommended operating conditions unless otherwise stated.
AC Electrical Characteristics1 - FPi0-2 and CKi0-2 Timing
No.
1
2
3
4
Characteristic (Figure 12)
FPi0-2 Input Frame Pulse Setup
Time
FPi0-2 Input Frame Pulse Hold
Time
FPi0-2 Input Frame Pulse width
CKi0-2 Input Clock Period
(average value, does not consider
the effects of jitter)
Sym.
Min.
tFPIS
tFPIH
tFPIW
tCKIP
Typ.2
Max.
Units
Notes
3
12
ns
CKi = 65.536 MHz
3
25
ns
CKi = 32.768 MHz
3
55
ns
CKi = 16.384 MHz
3
115
ns
CKi = 8.192 MHz
2
12
ns
CKi = 65.536 MHz
2
25
ns
CKi = 32.768 MHz
2
55
ns
CKi = 16.384 MHz
2
115
ns
CKi = 8.192 MHz
5
24
ns
CKi = 65.536 MHz
5
50
ns
CKi = 32.768 MHz
5
110
ns
CKi = 16.384 MHz
5
230
ns
CKi = 8.192 MHz
15
15.26
15.5
ns
65.536 MHz
30
30.5
31
ns
32.768 MHz
60
61.0
62
ns
16.384 MHz
120
122
124
ns
8.192 MHz
53
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
AC Electrical Characteristics1 - FPi0-2 and CKi0-2 Timing
No.
Characteristic (Figure 12)
Sym.
Min.
Typ.2
Max.
Units
5
CKi Input Clock High Time
tCKIH
4
ns
6
CKi Input Clock Low Time
tCKIL
4
ns
7
CKi Input Clock Rise/Fall Time
trCKI,
tfCKI
0
8
CKi Input Clock Cycle to Cycle
Variation
tCVC
Notes
6
ns
2
ns p-p
Standard rating3.
STi at 65 Mbps
4
ns p-p
Standard rating3.
STi at 32 Mbps
10
ns p-p
Standard rating3.
STi at 16 Mbps
20
ns p-p
Standard rating3.
STi at 8 Mbps
20% of
tCKIP
p-p
Extended rating.
With alternate clock
source4 or high
CKi0 rate5
Note 1:
Note 2:
Characteristics are over recommended operating conditions unless otherwise stated.
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
Note 3:
Note 4:
Note 5:
When using internal APLL clock source and the CKi0 frequency is less than or equal to the data rate.
When using input clock source CKi2-0 instead of the internal APLL clock source.
When using internal APLL clock source and the CKi0 frequency is higher than or equal to twice the data rate.
FPi
tFPIS
tFPH
tCKIP
tCKIH
tCKIL
CKi
trCKI
tfCKI
Input Frame Boundary
Figure 12 - Frame Pulse Input and Clock Input
54
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
AC Electrical Characteristics1 - FPi and CKi Skew
No.
1
Note 1:
Note 2:
Characteristic (Figure 13)
CKi0 to CKi1, 2 Skew
Sym.
Min.
tCKSK
-30
Typ.2
Max.
Units
+30
ns
Notes
CL 50 pF
Assume no jitter on input
clocks
Characteristics are over recommended operating conditions unless otherwise stated.
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
FPi0
CKi0
FPi1, 2
tCKSK
CKi1, 2
Frame Boundary
Figure 13 - Frame Skew Timing Diagram
55
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
AC Electrical Characteristics1 - FPO0-3 and CKO0-3 (65.536 MHz) Timing
No.
Characteristic
Sym.
Min.
Typ.2
Max.
Units
Notes3
1
FPO0-3 Output Frame Pulse
Setup Time
tFPOS
5.5
9.5
ns
CL=30 pF
2
FPO0-3 Output Frame Pulse Hold
Time
tFPOH
5.5
9.5
ns
CL=30 pF
3
CKO0-3 Output Clock Period
tCKOP
14.5
15.5
ns
CL=30 pF
AC Electrical Characteristics1 - FPO0-3 and CKO0-3 (32.768 MHz) Timing
No.
Characteristic
Sym.
Min.
Typ.2
Max.
Units
Notes3
1
FPO0-3 Output Frame Pulse
Setup Time
tFPOS
14.0
16.5
ns
CL=30 pF
2
FPO0-3 Output Frame Pulse Hold
Time
tFPOH
14.0
16.5
ns
CL=30 pF
3
CKO0-3 Output Clock Period
tCKOP
30.0
31.0
ns
CL=30 pF
Max.
Units
AC Electrical Characteristics1 - FPO0-3 and CKO0-3 (16.384 MHz) Timing
No.
Characteristic
Sym.
Min.
Typ.2
Notes3
1
FPO0-3 Output Frame Pulse
Setup Time
tFPOS
29.0
31.0
ns
CL=30 pF
2
FPO0-3 Output Frame Pulse Hold
Time
tFPOH
29.0
31.0
ns
CL=30 pF
3
CKO0-3 Output Clock Period
tCKOP
60.5
61.5
ns
CL=30 pF
AC Electrical Characteristics1 - FPO0-3 and CKO0-3 (8.192 MHz) Timing
No.
Characteristic
Sym.
Min.
Typ.2
Max.
Units
Notes3
1
FPO0-3 Output Frame Pulse
Setup Time
tFPOS
60.0
62.0
ns
CL=30 pF
2
FPO0-3 Output Frame Pulse Hold
Time
tFPOH
60.0
62.0
ns
CL=30 pF
3
CKO0-3 Output Clock Period
tCKOP
121.5
122.5
ns
CL=30 pF
Note 1:
Note 2:
Characteristics are over recommended operating conditions unless otherwise stated.
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
Note 3:
CKo clock source set to internal 131MHz APLL.
56
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
FPo0-3
tFPOS
tFPOH
tCKOP
CKo0-3
Output Frame Boundary
Figure 14 - ST-Bus Frame Pulse and Clock Output Timing
FPo0-3
tFPOS
tFPOH
tCKOP
CKo0-3
Output Frame Boundary
Figure 15 - GCI Frame Pulse and Clock Output Timing
AC Electrical Characteristics - Output Clock Jitter Generation
No.
Characteristic
Max.
Units
1
Jitter at CKO0-3 (8.192 MHz)
1050
ps-pp
2
Jitter at CKO0-3 (16.384 MHz)
1030
ps-pp
3
Jitter at CKO0-3 (32.768 MHz)
920
ps-pp
4
Jitter at CKO0-3 (65.536 MHz)
810
ps-pp
Note 1:
CKi at 8 MHz, output clock source set to internal APLL. No jitter presented on the Cki0 input.
Note 2:
For 65.536 MHz output clock, the total loading on the output should not be larger than 10pF.
57
Zarlink Semiconductor Inc.
Notes1,2
ZL50073
Data Sheet
AC Electrical Characteristics1 - Serial Data Timing2 to CKi
No.
1
2
Characteristic (Figure )
CKi to CKo Positive edge
Propagation Delay
CKi to CKo Negative edge
Propagation Delay
Max.
Units
Notes4
3.5
8
ns
CKo clock source =
CKi
4.1
9.2
ns
CKo Clock source =
Internal 131 MHz
APLL output
4.5
9.2
ns
CKo clock source =
CKi
5
10.1
ns
CKo Clock source =
Internal 131 MHz
APLL output
Sym.
Min.
tCKDP
tCKDN
Typ.3
3
STi to posedge CKi setup
tSIPS
-0.8
ns
4
STi to posedge CKi hold
tSIPH
5.9
ns
5
STi to negedge CKi setup
tSINS
-0.8
ns
6
STi to negedge CKi hold
tSINH
5.9
ns
7
Posedge CKi to Output Data Valid
tSIPV
4.8
11.6
ns
SToA5
4.1
13.7
ns
SToB, C, D5
5.8
12.9
ns
SToA5
4.5
14.8
ns
SToB, C, D5
4.3
14.6
ns
SToA5
4.6
14.5
ns
SToB, C, D5
5.3
13
ns
SToA5
5.7
13.6
ns
SToB, C, D5
10
ns
SToA
CL = 30 pF, RL = 1K5
11
ns
SToB, C, D
CL = 30 pF, RL = 1K5
4.5
15
ns
SToA5
6
20
ns
SToB, C, D5
8
9
10
11
12
Negedge CKi to Output Data Valid
tSINV
Posedge CKi to Output Data
tri-state
tSIPZ
Negedge CKi to Output Data
tri-state
tSINZ
ODE to Output Data tri-state
tSOZ
ODE to Output Data Enable
tSOE
Note 1:
Note 2:
Note 3:
Characteristics are over recommended operating conditions unless other wise stated.
All of these specifications refer to ST-BUS inputs and outputs with clock source set to CKi.
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
Note 4:
Note 5:
Loads on all serial outputs set to 30 pF.
High Impedance is measured by pulling to the appropriate rail with R L, with timing corrected to cancel time taken to discharge
C L.
58
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
FPi
(negative sense)
tCKDN
CKo
(negative sense)
CKi
(negative sense)
tSINS
tSINH
STin
VALID DATA *
tSINV
STon
tSINZ
STon
tSOZ
ODE
tSOE
FPi
(negative sense)
tCKDP
CKo
(positive sense)
CKi
(positive sense)
tSIPS
tSIPH
STin
VALID DATA
*
tSIPV
STon
tSIPZ
STon
Note 1: CKi frequency is assumed to be twice of the STin data rate, so that the sampling point is at the
3/4 point of the bit cell, or 1 1/2 clock period after the active clock edge
Note 2: If CKi frequency is the same as the STin data rate, the sampling point moves to the 1/2 point of
the bit cell, or 1/2 clock period after the active clock edge.
Figure 16 - Serial Data Timing to CKi
59
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
AC Electrical Characteristics - Serial Data Timing1 to CKo2
No.
Characteristic (Figure 17)
Sym.
Min.
Typ.3
Max.
Units
Notes4
1
STi to posedge CKo setup
tSOPS
7.3
ns
2
STi to posedge CKo hold
tSOPH
-2.0
ns
3
STi to negedge CKo setup
tSONS
7.3
ns
4
STi to negedge CKo hold
tSONH
-2.0
ns
5
Posedge CKo to Output Data Valid
tSOPV
0.1
2.7
ns
SToA4
0
4.6
ns
SToB, C, D4
-1.2
1.7
ns
SToA4
-1.6
3.7
ns
SToB, C, D4
0.9
4.9
ns
SToA4
0.1
5.1
ns
SToB, C, D4
0.4
4.7
ns
SToA4
0
4.8
ns
SToB, C, D4
6
7
8
Negedge CKo to Output Data Valid
tSONV
Posedge CKo to Output Data tri-state
Negedge CKo to Output Data tri-state
tSOPZ
tSONZ
Note 1:
Note 2:
Note 3:
Data Capture points vary with respect to CKo edge depending on clock rates & fractional delay settings.
All of these specifications refer to ST-BUS inputs, ST-BUS outputs and CKo outputs set to internal clock source.
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
Note 4:
Loads on all serial outputs set to 30 pF.
60
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
FPo
(negative sense)
CKo
(negative sense)
tSONS
tSONH
STin
tSONV
VALID DATA
*
STon
tSONZ
STon
FPo
(negative sense)
CKo
(positive sense)
tSOPS
tSOPH
STin
tSOPV
VALID DATA
*
STon
tSOPZ
STon
Note 1: CKo frequency is assumed to be twice of the STin data rate, so that the sampling point is at the
3/4 point of the bit cell, or 1 1/2 clock period after the active clock edge
Note 2: If CKo frequency is the same as the STin data rate, the sampling point moves to the 1/2 point of
the bit cell, or 1/2 clock period after the active clock edge.
Figure 17 - Serial Data Timing to CKo
61
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
AC Electrical Characteristics - CKo to Other CKo Skew1
No.
Characteristic (Figure 17)
Sym.
Min.
Typ.2
Max.
Units
1
CKo1 to CKo0 skew
tCKOS1-0
0
1.2
ns
2
CKo2 to CKo0 skew
tCKOS2-0
0
1.2
ns
3
CKo1 to CKo3 skew
tCKOS1-3
0
1.2
ns
4
CKo2 to CKo3 skew
tCKOS2-3
0
1.2
ns
5
CKo3 to CKo0 skew
tCKOS3-0
-0.6
0.6
ns
6
CKo2 to CKo1 skew
tCKOS2-1
-0.6
0.6
ns
Note 1:
Note 2:
Notes
All of these specifications refer to ST-BUS inputs, ST-BUS outputs and CKo outputs set to internal clock source.
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
CKo0
tCKOS3-0
CKo3
tCKOS1-3
tCKOS1-0
CKo1
tCKOS2-0
tCKOS2-1
CKo2
tCKOS2-3
Figure 18 - CKo to other CKo Skew
62
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
AC Electrical Characteristics - Microprocessor Bus Interface
No
Characteristics (Figure , & Figure 20)
Sym.
Min.
Typ.1
Max.
Units
Notes
1
DS Recovery
tDSRE
5
ns
2
CS Recovery
tCSRE
0
ns
3
CS asserted setup to DS asserted
tCSS
0
ns
4
Address, SIZ1-0, R/W setup to DS asserted
tADS
0
ns
5
CS hold from DS deasserted
tCSH
0
ns
6
Address, SIZ0-1, R/W hold from DS
deasserted
tADH
0
ns
7
Data valid to DTA asserted on read
tDSR
0
ns
CL = 50 pF,
RL = 1 k2
8
CS deasserted to Data tri-stated on read
ns
CL = 50 pF,
RL = 1 k2
9
Data setup to DS asserted on write
tWDS
10
CS asserted to WAIT deasserted
tCSWA
11
Data hold from DTA asserted on write
tDHW
12
DS asserted to WAIT Asserted
tWDD
13
WAIT deasserted to DTA/BERR asserted
skew
tAKS
14
DS asserted to DTA Asserted
tAKD
5
tDZ
0
ns
9
0
ns
CL = 30 pF,
RL = 1K2
ns
9
ns
CL = 50 pF,
RL = 1 k2
0
10
ns
CL = 50 pF,
RL = 1 k2
35
155
ns
Connection
Memory
50
75
ns
All other
registers
15
DS deasserted to DTA Deasserted
tAKH
7
ns
CL = 30 pF,
RL = 1K2
16
CS deasserted to DTA tri-stated
tDTHZ
13
ns
CL = 30 pF,
RL = 1 K2
17
CS deasserted to WAIT tri-stated
tWAHZ
6
ns
CL = 30 pF,
RL = 1K2
18
BE or UDS/LDS skew
tDSK
20
ns
19
BE or UDS/LDS to DS set-up
tBEDS
0
Note 1:
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
Note 2:
High Impedance is measured by pulling to the appropriate rail with R L, with timing corrected to cancel time taken to discharge
C L.
63
Zarlink Semiconductor Inc.
ZL50073
DS
(UDS,LDS)
tCSRE
Data Sheet
tCSS
tCSH
tADS
tADH
CS
VALID
A18-A0
RWN,SIZ
tDZ
D31-D0
READ
VALID READ DATA
tWDS
VALID WRITE DATA
D31-D0
WRITE
tDSR
Hi-Z
DTA
BERR
tAKD
tCSWA
tWDD
tDHW
tDSR
(BE1-0 or
UDS, LDS)
tWAHZ
Hi-Z
Figure 19 - Microprocessor Bus Interface Timing
DS
Hi-Z
tAKH
tAKS
Hi-Z
WAIT
tDTHZ
tBEDS
tDSK
Figure 20 - Intel Mode Timing
64
Zarlink Semiconductor Inc.
ZL50073
Data Sheet
AC Electrical Characteristics1 - IEEE 1149.1 Test Port and PWR Pin Timing
No.
Characteristic (Figure 21)
Sym.
Min.
100
Typ.2
Max.
Units
1
TCK Clock Period
tTCKP
2
TCK Clock Frequency
tTCKF
3
TCK Clock Pulse Width High
tTCKH
20
ns
4
TCK Clock Pulse Width Low
tTCKL
20
ns
5
TMS Set-up Time
tTMSS
10
ns
6
TMS Hold Time
tTMSH
10
ns
7
TDi Input Set-up Time
tTDIS
20
ns
8
TDi Input Hold Time
tTDIH
60
ns
9
TDo Output Delay
tTDOD
10
TRST pulse width
tTRSTW
20
ns
11
PWR pulse width
tTPWR
20
ns
Note 1:
Note 2:
Notes
ns
10
MHz
20
ns
CL = 30 pF
Characteristics are over recommended operating conditions unless otherwise stated.
Typical figures are at 25°C, V DD_CORE at 1.8 V and V DD_IO at 3.3 V and are for design aid only: not guaranteed and not
subject to production testing.
tTCKL
tTCKH
tTCKP
TCK
tTMSS
tTMSH
TMS
tTDIS
tTDIH
TDi
tTDOD
TDo
tTRSTW
TRST
tTPWR
PWR
Figure 21 - IEEE 1149.1 Test Port & PWR Reset Timing
65
Zarlink Semiconductor Inc.
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable.
However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such
information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or
use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual
property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in
certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE