EN

Spindle position displays
Through hollow shaft max. ø14 mm, with infrared interface
Format alignment by power tool, interface RS485
N 153
Features
–– Infrared interface for format alignment by power tool
–– Two keys for format alignment touch by touch
–– Through hollow shaft up to ø14 mm
–– Resolution: 1440 steps/revolution ±4096 revolutions
–– Display: LCD backlit, two lines
–– Absolute multiturn measuring system
–– Actual value and target display
–– Interface RS485
–– LED status indicator
Technical data - mechanical design
Voltage supply
24 VDC ±10 %
Shaft type
ø14 mm (through hollow shaft)
Current consumption
≤40 mA
Operating speed
≤600 rpm (short-term)
Display
LCD, 7-segment display,
2-lines, backlit
Protection DIN EN 60529
IP 50, IP 54 (on request)
Measuring principle
Absolute multiturn measuring
system
Operating temperature
-10...+50 °C
Storage temperature
-20...+70 °C
Measuring range
-99.99...+999.99 mm
-9.999...+99.999 inch
Relative humidity
80 % non-condensing
Torque support
Torque pin provided at housing
Steps per turn
1440
Connection
Number of turns
4096 / 12 bit
Spindle pitch
≤14 mm
Interface
RS485 (ASCII protocol)
- Male/female connector M8,
4-pin
- Cable output (30/15 cm) with
male/female connector M8,
4-pin
Data memory
Parameter buffer: EEPROM
Current value buffer: >10 years
by integrated 3 V lithium battery
Operation / keypad
Membrane with two keys
Housing type
Surface-mount with hollow shaft
Programmable
parameters
Display position horizontal/
vertical
Measuring unit mm/inch
Spindle pitch
Counting direction
Spindle tolerance
Positioning direction
Direction arrows
Tolerance window
Round up/down
Dimensions
37 x 75 x 45 mm
Mounting
Surface-mount with hollow shaft
Weight approx.
120 g
Material
Polyamide black, UL 94V-0
Motive positioning
Two softkeys for format
alignment
Connected to power tool by
infrared interface
Standard
DIN EN 61010‑1
Protection class II
Overvoltage category II
Pollution degree 2
Emitted interference
DIN EN 61000-6-3
Interference immunity
DIN EN 61000-6-2
Approval
UL approval / E63076
1
www.baumer.com/motion
24/5/2016
Technical data - electrical ratings
Subject to modification in technic and design. Errors and omissions excepted.
N 153 with cable output
Spindle position displays
Through hollow shaft max. ø14 mm, with infrared interface
Format alignment by power tool, interface RS485
N 153
Part number
1
3
A
A
multicon AccuDrive is an economical system for mobile,
motive format alignment. By AccuDrive positioning of shafts
to the desired format is quick, accurate and less fussy hand
crank operations. Saving setup times and avoiding editing
errors are consequently the most convincing arguments.
The electrically commutated professional power tool ASMIR
serves as mobile actuator that communicates with N 153
spindle position displays by infrared interface. Red and
green status LEDs provided at the position display indicate
the operator which shafts require alignment. A flashing LED
indicates the positioning order.
The power tool is a vital help in aligning the respective
shafts to the new format. Select the desired positioning direction by aid of the two pushbuttons provided at the power
tool. Press and hold the start button to start the positioning
operation at slow speed with increasing acceleration. This
way, the operator is able to proceed the positioning operation in direct sight with an accuracy of ±1/100 mm.
Any shaft positions once effected can be filed under a
parameter profile in the control to be recalled any time. By
serial interface maximum 32 spindle position displays may
be networked to PC or PLC. Through solutions are realized by memory controller N 242 as memory and operating
terminal where max. 100 format profiles can be entered and
saved by Teach-in.
01
Through hollow shaft
A ø14 mm
Display
A Inclined
Voltage supply
3 24 VDC
Connection
0 Connector output M8
1 Cable output M8
Interface
1 RS485
Accessories
Z 178.A01
Adaptor cable between cable connector M8
and female M16, 1 m
Z 178.AW1
Cable connector M8, 4-pin, without cable with
integrated terminating resistor 120 Ω
Z 178.B01
Female connector M8, 4-pin, without cable
Z 178.D05
Data and supply cable M8, Master to N 150
and N 155, 5 m
Z 178.S01
Cable connector M8, 4-pin, without cable
Z 178.V01
Coupling cable with M8 - M8, 1 m cable
Z 178.V03
Coupling cable with M8 - M8, 3 m cable
Z 178.V05
Coupling cable with M8 - M8, 5 m cable
Z 178.V10
Coupling cable with M8 - M8, 10 m cable
Z 178.050
Data and supply cable, ø5 mm,
4 cores, shielded, on 50 m drum
Subject to modification in technic and design. Errors and omissions excepted.
Connectors and cables
2
www.baumer.com/motion
24/5/2016
N 153.
Description
Spindle position displays
Through hollow shaft max. ø14 mm, with infrared interface
Format alignment by power tool, interface RS485
N 153
Terminal assignment
SPA – connector and female connector, 4-pin
Connector
Assignment
Pin 1
Tx/Rx-, RS485
Pin 2
Tx/Rx+, RS485
Pin 3
Sensor supply +24 V
Pin 4
Sensor supply 0 V
M8 connector
1
3
M8 female
connector
2
2
4
4
1
3
Dimensions
Connect or output
4.8 Torque pin
6
°
Cable output
ø14H7
300
A
Seal
14
A
1
13
52
12.5
M8
connector
Connector
Female connector
3
ø12
ø12
www.baumer.com/motion
Subject to modification in technic and design. Errors and omissions excepted.
45
M8
female
connector
24/5/2016
6.5
31.8
30.15
10
ø6h9
28
2:1
60
16
Pin M4
13
26
37
StatusLED
IR-Diode
ø20
22
20.5
75
0.5x 45°
150
75