Spindle position displays Through hollow shaft max. ø14 mm, automated format alignment Display LCD two lines, interface RS485 N 152 Features –– Automated format alignment –– Two keys for format alignment touch by touch –– Through hollow shaft up to ø14 mm –– Resolution: 1440 steps/revolution ±4096 revolutions –– Display: LCD backlit, two lines –– Absolute multiturn measuring system –– Actual value and target display –– Interface RS485 Technical data - mechanical design Voltage supply 24 VDC ±10 % Shaft type ø14 mm (through hollow shaft) Current consumption ≤40 mA Operating speed ≤600 rpm (short-term) Display LCD, 7-segment display, 2-lines, backlit Protection DIN EN 60529 IP 50 Measuring principle Absolute multiturn measuring system Operating temperature -10...+50 °C Storage temperature -20...+70 °C Measuring range -99.99...+999.99 mm -9.999...+99.999 inch Relative humidity 80 % non-condensing Torque support Torque pin provided at housing Steps per turn 1440 Connection Number of turns 4096 / 12 bit Spindle pitch ≤14 mm - Cable output (15 cm) with male connector M8, 4-pin - Motor cable with female connector M16, 12-pin Interface RS485 (ASCII protocol) Operation / keypad Membrane with two keys Data memory Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Housing type Surface-mount with hollow shaft Dimensions 37 x 75 x 45 mm Mounting Surface-mount with hollow shaft Weight approx. 120 g Material Polyamide black, UL 94V-0 Programmable parameters Display position horizontal/ vertical Measuring unit mm/inch Counting direction Spindle pitch Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Motive positioning Two softkeys for format alignment Direct motor connection to N 152 by motor cable Standard DIN EN 61010‑1 Protection class II Overvoltage category II Pollution degree 2 Emitted interference DIN EN 61000-6-3 Interference immunity DIN EN 61000-6-2 Approval UL approval / E63076 1 www.baumer.com/motion 21/3/2016 Technical data - electrical ratings Subject to modification in technic and design. Errors and omissions excepted. N 152 with cable output Spindle position displays Through hollow shaft max. ø14 mm, automated format alignment Display LCD two lines, interface RS485 N 152 Part number N 152. 1 Description 3 A multiconDrive represents a simplified and very efficient, reasonably priced system for automatic format alignment. With multiconDrive the spindle position displays communicate directly with EC motors. Every spindle position display is connected to the corresponding motor by a separate cable output providing the motor without delay with the signals "clockwise", "counterclockwise", "rotation speed" for switchover to high/low speed. The spindle position display provides two keys for clockwise and counterclockwise direction used during the first editing operation. The key makes the motor moving into the requested direction. A soft touch results in a defined STEP. Thus, new spindle positions can be edited under direct visual check of the operator with an accuracy of ±1/100 mm. Shaft position parameters once set can be filed as profile in the control. The serial interface enables network of maximum 32 spindle position displays with PC or PLC. For complete solutions N 242 memory controller as operating and memory terminal is available. Up to 100 format profiles can be stored by teach-in. The respective position parameters can be retransmitted at any time as target to the respecitve spindle position displays to release automatic format alignment cycles. 01 Through hollow shaft A ø14 mm Display A Inclined B Horizontal at front Voltage supply 3 24 VDC Connection 1 Cable output M8, motor cable 0.5 m 2 Cable output M8, motor cable 1.5 m Interface 1 RS485 Accessories Adaptor cable between cable connector M8 and female M16, 1 m Z 178.AW1 Cable connector M8, 4-pin, without cable with integrated terminating resistor 120 Ω Z 178.B01 Female connector M8, 4-pin, without cable Z 178.D05 Data and supply cable M8, Master to N 150 and N 155, 5 m Z 165.E01 Extension cable SPA-motor (male/female) M16, 12-pin, 1 m Z 178.S01 Cable connector M8, 4-pin, without cable Z 178.V01 Coupling cable with M8 - M8, 1 m cable Z 178.Y02 Y-junction M8, 4-pin, with cable Z 178.V03 Coupling cable with M8 - M8, 3 m cable Z 178.V05 Coupling cable with M8 - M8, 5 m cable Z 178.V10 Coupling cable with M8 - M8, 10 m cable Z 178.050 Data and supply cable, ø5 mm, 4 cores, shielded, on 50 m drum 2 www.baumer.com/motion 21/3/2016 Z 178.A01 Subject to modification in technic and design. Errors and omissions excepted. Connectors and cables Spindle position displays Through hollow shaft max. ø14 mm, automated format alignment Display LCD two lines, interface RS485 N 152 Terminal assignment SPA – connector, 4-pin Motor connector, 12-pin M8 connector Assignment Connector Assignment Pin 1 Tx/Rx–, RS485 Pin A – Pin 2 Tx/Rx+, RS485 Pin B Motor left Pin 3 Sensor supply +24 V Pin C Motor right Pin 4 Sensor supply 0 V Pin D Speed M8 connector Pin E – Pin F – Pin G – Pin H – Pin J – Pin K Error signal Pin L Speed Pin M GND 1 3 2 4 M16 male connector B C L D E A K J M H F G Enable n.c. 1 2 3 4 5 6 7 8 24 V 0V IN 1 output IN 1 input IN 2 output IN 2 input (logic 24 V) OUT 1 IN 1 (left) IN 2 (right) IN 4 (speed) 24 V n.c. n.c. AI- (0...10 V) AI+ (0...10 V) OUT 3 (fault) IN 3 (speed) 0V M Motor 3 A B C D E F G H J K Error L M Motor left Motor right Speed n.c. n.c. n.c. n.c. n.c. Error signal Speed GND SPA www.baumer.com/motion 21/3/2016 supply voltage release counterclockwise release clockwise Subject to modification in technic and design. Errors and omissions excepted. Circuit diagram Spindle position displays Through hollow shaft max. ø14 mm, automated format alignment Display LCD two lines, interface RS485 N 152 Dimensions Optional display position 75 ° 4.8 Torque pin 6 28 2:1 ø6h9 ø14H7 20.5 ø20 22 Pin M4 Seal 6.5 M16 male connector / motor 37 1 M8 mal e connector Subject to modification in technic and design. Errors and omissions excepted. 45 12.5 30.15 31.8 4 www.baumer.com/motion 21/3/2016 75 0.5x 45°